Search NASA⌕ Search

SEARCH · Search NASA

Results for “transferability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The effects of turbulence and stator/rotor interactions on turbine heat transfer. II - Effects of Reynolds number and incidence

Part I of this paper presents airfoil heat transfer data obtained in a rotating turbine model at its design rotor incidence. This portion of the paper presents heat transfer data obtained in the same model for various combinations of Reynolds number and inlet turbulence and for a very wide range of rotor incidence. On the suction surfaces of the first stage airfoils the locations and lengths of transition were influenced by both the inlet turbulence level and the Reynolds number. In addition it was demonstrated that on the first stage pressure surfaces combinations of high Reynolds number and high turbulence can produce heat transfer rates well in excess of two-dimensional turbulent flow. Rotor heat transfer distributions indicate that for relatively small deviations from the design incidence, local changes to the heat transfer distributions were produced on both pressure and suction sides near the stagnation region. For extremely large negative incidence the flow was completely separated from the rotor pressure surface producing very high local heat transfer.

Blair, M. F.↗
NASA NTRS1988

Heat transfer in gas turbine engines and three-dimensional flows; Proceedings of the Symposium, ASME Winter Annual Meeting, Chicago, IL, Nov. 27-Dec. 2, 1988

The present conference on heat transfer characteristics of gas turbines and three-dimensional flows discusses velocity-temperature fluctuation correlations at the flow stagnation flow of a circular cylinder in turbulent flow, heat transfer across turbulent boundary layers with pressure gradients, the effect of jet grid turbulence on boundary layer heat transfer, and heat transfer characteristics predictions for discrete-hole film cooling. Also discussed are local heat transfer in internally cooled turbine airfoil leading edges, secondary flows in vane cascades and curved ducts, three-dimensional numerical modeling in gas turbine coal combustor design, numerical and experimental results for tube-fin heat exchanger airflow and heating characteristics, and the computation of external hypersonic three-dimensional flow field and heat transfer characteristics.

Elovic, E.↗
NASA NTRS1989

Charge transfer and X-ray emission from supernova remnants

The X-ray line emission excited by charge transfer between neutral hydrogen and the hydrogenic or fully stripped ions of heavy elements has been computed for a grid of nonequilibrium ionization models for supernova remnants. The effects of charge transfer excitation on the X-ray spectra of supernova remnants are discussed. The charge transfer process depends very sensitively upon the abundance of neutral hydrogen behind the shock. Consequently, a careful treatment of the ionization of hydrogen was required. The model line fluxes are compared with those excited by conventional collisional processes involving electrons. Results are presented in the form of contour plots for both the flux excited by charge transfer and the ratio of the charge transfer flux to that associated solely with collisional processes involving electrons. Charge transfer never contributes more than 10 percent of the flux of the strongest electron collisionally excited lines, and its contribution is typically 0.001 to 10 to the -5th for a shock moving into a medium composed of neutral hydrogen.

Wise, Michael W.↗
NASA NTRS1989

Effects of very high turbulence on heat transfer

The effects of very high free stream turbulence on heat transfer were investigated experimentally by placing a flat plate, constant temperature heat transfer surface in a large diameter turbulent-free jet. The heat transfer rates measured were two to four times greater than those that would be predicted by accepted correlations for turbulent boundary layers. Thus, rather than establish a particular high turbulence flow field and then measure its effect on heat transfer, search for a flow field with very aggressive heat transfer characteristics and description of the aspects of the free stream turbulence associated with high levels of heat transfer is examined.

Maciejewski, Paul K.↗
NASA NTRS1990

The effects of high free-stream turbulence on heat transfer in turbulent boundary layer

A series of heat transfer measurements utilizing a variety of flows, each characterized by a high level of turbulence, is evaluated. This research is conducted to aid in predicting the heat transfer of first stage turbine blades and vanes. Instead of establishing a particular high turbulence flow field and measuring its effect on heat transfer, a set of flow fields with very aggressive heat transfer characteristics was determined in order to learn which aspects of these flows were responsible for the high heat transfer. Results of these tests were utilized to identify the most aggressive heat transfer environments, and then the turbulence properties of those flows were studied.

Maciejewski, Paul K.↗
NASA NTRS1990

Interfacial mass transfer to a cylinder endwall during spin-up/spin-down

The local rate of mass transfer to the bottom endwall of a large aspect ratio cylinder was measured during spin-up/spin-down. The local mass transfer rate was a strong function radial position along the endwall. At the center during spin-up from rest, the maximum enhancement in mass transfer occurred after the Ekman time scale and before the viscous time scale. At the center during spin-down to rest, a stagnation vortex formed, causing the mass transfer rate to decay and then increase back to the original value of the order of the viscous time scale. Away from the center a much more complicated pattern was observed, but spin-up and spin-down were similar. Two peaks in mass transfer rate occurred for an Ekman number over 0.0074. Alternating spin-up and spin-down with a short period caused the center of the endwall to experience a nearly sinusoidal variation in mass transfer with the frequency equal to the forcing frequency. Near the edge the frequency was twice the forcing frequency.

Larrousse, Mark F.↗
NASA NTRS1991

Two-dimensional Navier-Stokes heat transfer analysis for rough turbine blades

A quasi-three-dimensional thin-layer Navier-Stokes analysis was used to predict heat transfer to rough surfaces. Comparisons are made between predicted and experimental heat transfer for turbine blades and flat plates of known roughness. The effect of surface roughness on heat transfer was modeled using a mixing length approach. The effect of near-wall grid spacing and convergence criteria on the accuracy of the heat transfer predictions are examined. An eddy viscosity mixing length model having an inner and outer layer was used. A discussion of the appropriate model for the crossover between the inner and outer layers is included. The analytic results are compared with experimental data for both flat plates and turbine blade geometries. Comparisons between predicted and experimental heat transfer showed that a modeling roughness effects using a modified mixing length approach results in good predictions of the trends in heat transfer due to roughness.

Boyle, R. J.↗
NASA NTRS1991

Closed-loop transfer recovery with observer-based controllers. I - Analysis

The description of a novel problem in loop transfer recovery is presented. The problem of closed-loop recovery (CLTR) is examined using a measurement feedback-control law where the closed-loop transfer function from the external signal to the controlled output can be made either exactly equal or approximately close to the so-called target closed-loop transfer function achieved under full-state feedback. The analysis of CLTR applies specifically to the general class of observer-based controllers and focuses on three fundamental issues. The first issue is concerned with what can and cannot be achieved for a given system and for an arbitrary target closed-loop transfer function. The second issue is to develop necessary and/or sufficient conditions for a target closed-loop transfer function to be recoverable either exactly or approximately. The third issue deals with the necessary and/or sufficient conditions on a given system such that it has at least one recoverable target closed-loop transfer function. The result is applied to the lateral autopilot design for a commercial transport airplane.

Chen, Ben M.↗
NASA NTRS1991

Minimum fuel coplanar aeroassisted orbital transfer using collocation and nonlinear programming

The fuel optimal control problem arising in coplanar orbital transfer employing aeroassisted technology is addressed. The mission involves the transfer from high energy orbit (HEO) to low energy orbit (LEO) without plane change. The basic approach here is to employ a combination of propulsive maneuvers in space and aerodynamic maneuvers in the atmosphere. The basic sequence of events for the coplanar aeroassisted HEO to LEO orbit transfer consists of three phases. In the first phase, the transfer begins with a deorbit impulse at HEO which injects the vehicle into a elliptic transfer orbit with perigee inside the atmosphere. In the second phase, the vehicle is optimally controlled by lift and drag modulation to satisfy heating constraints and to exit the atmosphere with the desired flight path angle and velocity so that the apogee of the exit orbit is the altitude of the desired LEO. Finally, the second impulse is required to circularize the orbit at LEO. The performance index is maximum final mass. Simulation results show that the coplanar aerocapture is quite different from the case where orbital plane changes are made inside the atmosphere. In the latter case, the vehicle has to penetrate deeper into the atmosphere to perform the desired orbital plane change. For the coplanar case, the vehicle needs only to penetrate the atmosphere deep enough to reduce the exit velocity so the vehicle can be captured at the desired LEO. The peak heating rates are lower and the entry corridor is wider. From the thermal protection point of view, the coplanar transfer may be desirable. Parametric studies also show the maximum peak heating rates and the entry corridor width are functions of maximum lift coefficient. The problem is solved using a direct optimization technique which uses piecewise polynomial representation for the states and controls and collocation to represent the differential equations. This converts the optimal control problem into a nonlinear programming problem which is solved numerically by using a modified version of NPSOL. Solutions were obtained for the described problem for cases with and without heating constraints. The method appears to be more robust than other optimization methods. In addition, the method can handle complex dynamical constraints.

Shi, Yun Yuan↗
NASA NTRS1991

Heat transfer measurements from a smooth NACA 0012 airfoil

Local convective heat transfer coefficients were measured from a smooth NACA 0012 airfoil having a chord length of 0.533 m. Flight data were taken for the smooth airfoil at Reynolds numbers based on chord in the range 1.24 to 2.50 million and at various angles of attack up to 4 deg. During these flight tests, the freestream velocity turbulence intensity was found to be very low. Wind tunnel data were acquired in the Reynolds number range 1.20 to 4.52 million and at angles of attack from -4 to +8 deg. The turbulence intensity in the IRT was 0.5-0.7 percent with the cloud-generating sprays off. A direct comparison between the results obtained in flight and in the IRT showed that the higher level of turbulence intensity in the IRT had little effect on the heat transfer for the lower Reynolds numbers but caused a moderate increase in heat transfer at the higher Reynolds numbers. Turning on the cloud-generating spray nozzle atomizing air in the IRT did not alter the heat transfer. The present data were compared with leading-edge cylinder and flat plate heat transfer correlations that are often used to estimate airfoil heat transfer in computer codes.

Poinsatte, Philip E.↗
NASA NTRS1993

Practical aspects of transfer from GTO to lunar orbit

This paper is a presentation of some practical aspects of orbital transfer from Geosynchronous Transfer Orbit (GTO) to close, near-circular orbits of the Moon. The intent is to identify the important parameters affecting the problem and to bound (approximately) the range of required delta V for a spacecraft that has been placed in GTO. The basic geometric relationships are described and the dynamics are simulated by use of the Zero-Sphere-of Influence Patched Conic method. It is found that the inclination of the transfer orbit to the Earth-Moon plane is relatively unimportant while the position of the line of apsides with respect to the Moon's orbit is the main geometric parameter of interest. It is shown that this parameter can be controlled by selecting the time of day for launch and that two launch windows of approximately 45 minutes duration are available each day of the year if use is made of the recommended phasing orbit transfer. The phasing orbit transfer not only provides twice-daily launch windows, but also provides a mechanism for efficacious correction of GTO injection errors. Delta V penalties for out-of-plane transfer and for late launch are evaluated and the method is recommended for use as an affordable means of achieving lunar orbit.

Uphoff, Chauncey↗
NASA NTRS1992

Heat transfer with very high free-stream turbulence. I - Experimental data. II - Analysis of results

Boundary layer heat transfer with very high freestream turbulence is investigated. The problem is studied experimentally by placing a constant-temperature heat transfer surface at various locations in the margin of a turbulent free jet and measuring both the surface heat transfer rate and the turbulence in the freestream. Freestream turbulent fluctuations 20 to 60 percent relative to the mean velocity augment heat transfer 1.8 to 4 times that which would be predicted locally using accepted correlations for turbulent boundary layers at the same Reynolds number. The correlations of Simonich and Bradshaw (1989), Pedisius et al. (1983), and Blair (1983) each fail to describe the present data. For flows over flat surfaces in air with very high freestream turbulence, greater than 0.2, u-prime determines h. A new heat transfer parameter, St-prime, characterizes turbulent boundary layer heat transfer with freestream turbulence on the domain 0-0.65 to within +/- 15 percent for high Reynolds number flows with uniform thermal boundary conditions.

Maciejewski, P. K.↗
NASA NTRS1992

Effect of uneven wall temperature on local heat transfer in a rotating square channel with smooth walls and radial outward flow

The effect of uneven wall temperature on the local heat transfer coefficient in a rotating square channel with smooth walls and radial outward flow is investigated for Reynolds numbers from 2500 to 25,000 and rotation numbers from 0 to 0.352. Three cases of thermal boundary conditions are studied: (1) four walls uniform temperature, (2) four walls uniform heat flux, and (3) leading and trailing walls hot and two side walls cold. It is shown that the heat transfer coefficients on the leading surface are much lower than that of the trailing surface due to rotation. For case 1, the leading surface heat transfer coefficient decreases and then increases with increasing rotation numbers, and the trailing surface heat transfer coefficient increases monotonically with rotation numbers. The trailing surface heat transfer coefficients, as well as those for the side walls, for case 2 are higher than for case 1, and the leading surface heat transfer coefficients for cases 2 and 3 are significantly higher than for case 1.

Han, J.-C.↗
NASA NTRS1992

An experimental study of heat transfer in a large-scale turbine rotor passage

An experimental study of the heat transfer distribution in a turbine rotor passage was conducted in a large-scale, ambient temperature, rotating turbine model. Heat transfer was measured for both the full-span suction and pressure surfaces of the airfoil as well as for the hub endwall surface. The objective of this program was to document the effects of flow three-dimensionality on the heat transfer in a rotating blade row (vs a stationary cascade). Of particular interest were the effects of the hub and tip secondary flows, tip leakage and the leading-edge horseshoe vortex system. The effect of surface roughness on the passage heat transfer was also investigated. Midspan results are compared with both smooth-wall and rough-wall finite-difference two-dimensional heat transfer predictions. Contour maps of Stanton number for both the rotor airfoil and endwall surfaces revealed numerous regions of high heat transfer produced by the three-dimensional flows within the rotor passage. Of particular importance are regions of local enhancement (as much as 100 percent over midspan values) produced on the airfoil suction surface by the secondary flows and tip-leakage vortices and on the hub endwall by the leading-edge horseshoe vortex system.

Blair, Michael F.↗
NASA NTRS1993

Conjugate heat transfer from a heated disk to a thin liquid film formed by a controlled impinging jet

An experimental and numerical study of the heat transfer from a heated horizontal disk to a thin film of liquid is described. The liquid was delivered to the disk by a collar arrangement such that the film thickness and radial velocity were known at the outer radius of the collar. This method of delivery is termed as a controlled impinging jet. Flow visualization tests were performed and heat transfer data were collected along the radius of the disk for different volumetric flow rates and inlet temperatures in the supercritical and subcritical regions. The heat transfer coefficient was found to increase with flow rate when both supercritical and subcritical regions were present on the heated surface. A numerical simulation of this free surface problem was performed, which included the effects of conjugate heat transfer within the heated disk and the liquid. The numerical predictions agree with the experimental results and show that conjugate heat transfer has a significant effect on the local wail temperature and heat transfer coefficient.

Faghri, A.↗
NASA NTRS1993

High Reynolds number and turbulence effects on aerodynamics and heat transfer in a turbine cascade

Experimental data on pressure distribution and heat transfer on a turbine airfoil were obtained over a range of Reynolds numbers from 0.75 to 7.5 million and a range of turbulence intensities from 1.8 to about 15 percent. Fundamental heat transfer and pressure distribution data are obtained over a wide range of high Reynolds numbers and to extend the heat transfer data base to include the range of Reynolds numbers encountered in the SSME turbopump turbines. The results obtained indicated that Reynolds number and turbulence intensity have a large effect on both the transition from laminar to turbulent flow and the resulting heat transfer. For a given turbulence intensity, heat transfer for all Reynolds numbers at the leading edge can be correlated with the Frossling number developed for lower Reynolds numbers. For a given turbulence intensity, heat transfer for the airfoil surfaces downstream of the leading edge can be approximately correlated with a dimensionless parameter. Comparison of the experimental results were also made with a numerical solution from a 2D Navier-Stokes code.

Yeh, Frederick C.↗
NASA NTRS1991

Two-dimensional Navier-Stokes heat transfer analysis for rough turbine blades

A quasi-three-dimensional thin-layer Navier-Stokes analysis was used to predict heat transfer to rough surfaces. Comparisons are made between predicted and experimental heat transfer for turbine blades and flat plates of known roughness. The effect of surface roughness on heat transfer was modeled using a mixing length approach. The effect of near-wall grid spacing and convergence criteria on the accuracy of the heat transfer predictions are examined. An eddy viscosity mixing length model having an inner and outer layer was used. A discussion of the appropriate model for the crossover between the inner and outer layers is included. The analytic results are compared with experimental data for both flat plates and turbine blade geometries. Comparisons between predicted and experimental heat transfer showed that a modeling roughness effects using a modified mixing length approach results in good predictions of the trends in heat transfer due to roughness.

Boyle, R. J.↗
NASA NTRS1994

Three-dimensional aspects of radiative transfer in remote sensing of precipitation: Application to the 1986 COHMEX storm

Several multifrequency techniques for passive microwave estimation of precipitation based on the absorption and scattering properties of hydrometers have been proposed in the literature. In the present study, plane-parallel limitations are overcome by using a model based on the discrete-ordinates method to solve the radiative transfer equation in three-dimensional rectangular domains. This effectively accounts for the complexity and variety of radiation problems encountered in the atmosphere. This investigation presents result for plane-parallel and three-dimensional radiative transfer for a precipitating system, discusses differences between these results, and suggests possible explanations for these differences. Microphysical properties were obtained from the Colorado State University Regional Atmospehric Modeling System and represent a hailstorm observed during the 1986 Cooperative Huntsville Meteorological Experiment. These properties are used as input to a three-dimensional radiative transfer model in order to simulate satellite observation of the storm. The model output consists of upwelling brightness temperatures at several of the frequencies on the Special Sensor Microwave/Imager. The radiative transfer model accounts for scattering and emission of atmospheric gases and hydrometers in liquid and ice phases. Brightness temperatures obtained from the three-dimensional model of this investigation indicate that horizontal inhomogeneities give rise to brightness temperature fields that can be quite different from fields obtained using plane-parallel radiative transfer theory. These differences are examined for various resolutions of the satellite sensor field of view. In adddition, the issue of boundary conditions for three-dimensional atmospheric radiative transfer is addressed.

Haferman, J. L.↗