Search NASA⌕ Search

SEARCH · Search NASA

Results for “vertical profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Requirements and Technology Advances for Global Wind Measurement with a Coherent Lidar: A Shrinking Gap

Early concepts to globally measure vertical profiles of vector horizontal wind from space planned on an orbit height of 525 km, a single pulsed coherent Doppler lidar system to cover the full troposphere, and a continuously rotating telescope/scanner that mandated a vertical line of sight wind profile from each laser shot. Under these conditions system studies found that laser pulse energies of approximately 20 J at 10 Hz pulse repetition rate with a rotating telescope diameter of approximately 1.5 m was required. Further requirements to use solid state laser technology and an eyesafe wavelength led to the relatively new 2-micron solid state laser. With demonstrated pulse energies near 20 mJ at 5 Hz, and no demonstration of a rotating telescope maintaining diffraction limited performance in space, the technology gap between requirements and demonstration was formidable. Fortunately the involved scientists and engineers set out to reduce the gap, and through a combination of clever ideas and technology advances over the last 15 years, they have succeeded. This paper will detail the gap reducing factors and will present the current status.

Kavaya, Michael J.↗

The vertical structure of diabatic heating associated with the Madden-Julian oscillation simulated by the Goddard Laboratory for Atmospheres climate model

The diabatic heating structure of the nine-layer Goddard Laboratory for Atmospheres model of the Madden-Julian oscillation (MJO) is illustrated with composite charts made for those times when this low-frequency mode reaches its maximum and minimum amplitudes. These composite charts compare the vertically integrated diabatic heating with potential functions, the vertical distribution of diabatic heating with the east-west mass flux function in the tropics, and the vertical profiles of diabatic heating at the centers of maximum and minimum MJO amplitude. Three interesting features of the model MJO's diabatic heating are revealed: (1) the maximum heating rate of this low-frequency mode is located over the Asian monsoon region and its amplitude is about a half of the maximum value of the seasonal mean heating rate in this region, (2) the vertical diabatic heating rate profile has a maximum at 500 mbar and resembles the seasonal mean total heating profile, and (3) the total diabatic heating is for the most part composed of the latent heat released by cumulus convection.

Chen, Tsing-Chang↗

Profiles of temperature and density based on extremes at 5, 10, 20, 30 and 40 km

Information on the vertical distribution of expected extremes of temperature and density are required for the design and operation of systems traversing the atmosphere. Such data are particularly important at altitudes from the surface to approximately 80 km for developing all types of airborne vehicles ranging from helicopters and airplanes to sophisticated aerospace systems. Vertical profiles of temperature and density have been developed based on 1- and 10-percent hot and cold temperatures and 1- and 10- percent high and low densities occurring during the most severe month at the worst locations for which reliable upper-air data are available. The model profiles, from the surface to 80 km, are based on extremes that occur at 5, 10, 20, 30, and 40 km. There are 20 profiles for extreme temperatures (5 levels by 4 percentiles) that include associated densities, and 20 analogous profiles for extreme densities including associated temperatures. Consequently, a set of realistic profiles (rather than envelopes) of temperature and density, associated with extremes at each of 5 specified levels in the troposphere and stratosphere, are now available for altitudes up to 80 km.

Kantor, A. J.↗

Doppler lidar measurement of profiles of turbulence and momentum flux

A short-pulse CO2 Doppler lidar with 150-m range resolution measured vertical profiles of turbulence and momentum flux. Example measurements are reported of a daytime mixed layer with strong mechanical mixing caused by a wind speed of 15 m/sec, which exceeded the speed above the capping inversion. The lidar adapted an azimuth scanning technique previously demonstrated by radar. Scans alternating between two elevation angles allow determination of mean U-squared, V-squared, and W-squared. Expressions were derived to estimate the uncertainty in the turbulence parameters. A new processing method, partial Fourier decomposition, has less uncertainty than the filtering used earlier.

Eberhard, Wynn L.↗

Differential absorption lidars for remote sensing of atmospheric pressure and temperature profiles

A near infrared differential absorption lidar technique is developed using atmospheric oxygen as a tracer for high resolution vertical profiles of pressure and temperature with high accuracy. Solid-state tunable lasers and high-resolution spectrum analyzers are developed to carry out ground-based and airborne measurement demonstrations and results of the measurements presented. Numerical error analysis of high-altitude airborne and spaceborne experiments is carried out, and system concepts developed for their implementation.

Korb, C. Laurence↗

Measurement of aerosol profiles using high-spectral-resolution Rayleigh-Mie lidar

High-spectral-resolution Rayleigh-Mie lidar measurements of vertical profiles (1 to 5 km) of atmospheric pressure and density, as well as aerosol profiles, including backscatter ratio and extinction ratio are reported. These require simultaneous measurement of temperature. Use of the technique does not require any assumptions about the aerosol but does require that the pressure at one altitude is known and that the gas law of the air is known (e.g., an ideal gas).

Krueger, D. A.↗

First Reprocessing of Southern Hemisphere ADditional OZonesondes (SHADOZ) Profile Records (1998-2015): 1. Methodology and Evaluation

Electrochemical concentration cell ozonesonde measurements are an important source of highly resolved vertical profiles of ozone with long-term data records for deriving ozone trends, model development, satellite validation, and air quality studies. Ozonesonde stations employ a range of operational and data processing procedures, metadata reporting, and instrument changes that have resulted in inhomogeneities within individual station data records. A major milestone is the first reprocessing of seven Southern Hemisphere ADditional OZonesondes (SHADOZ) station ozonesonde records to account for errors and biases in operating/processing procedures. Ascension Island, Hanoi, Irene, Kuala Lumpur, La Reunion, Natal, and Watukosek station records all show an overall increase in ozone after reprocessing. Watukosek shows the largest increase of 9.0 plus or minus 2.1 Dobson Units (DU) in total column ozone; Irene and Hanoi show a 5.5 plus or minus 2.5 DU increase, while remaining sites show statistically insignificant enhancements. Negligible to modest ozone enhancements are observed after reprocessing in the troposphere (up to 8%) and stratosphere (up to 6%), except at La Reunion for which the application of background currents reduces tropospheric ozone (2.1 plus or minus1.3 DU). Inhomogeneities due to ozonesonde/solution-type changes at Ascension, Natal, and La Reunion are resolved with the application of transfer functions. Comparisons with EP-TOMS, Aura's Ozone Monitoring Instrument and Microwave Limb Sounder (MLS) satellite ozone overpasses show an overall improvement in agreement after reprocessing. Most reprocessed data sets show a significant reduction in biases with MLS at the ozone maximum region (50-10 hPa). Changes in radiosonde/ozonesonde system and nonstandard solution types can account for remaining discrepancies observed at several sites when compared to satellites.

Electrochemical concentration cell ozonesonde meas↗

Lightning Contribution to Improvement of Passive Microwave Vertical Structure and Rainfall Estimation

Joint observations from the TRMM mission are used to examine the contribution which lightning observations can make towards estimation of vertical structure and rainfall from passive microwave data. Passive microwave (TMI) observations are binned into distinct vertical structure categories based on cluster analysis of radar (PR) vertical profiles and convective/stratiform (C/S) classifiers. TMI rain estimates are high-biased relative to radar for stratiform and mixed convective/stratiform vertical structures and low-biased relative to radar for convective structures. Significant ambiguity exists in the TMI brightness temperature space between midlevel stratiform and convective profile types which are primary contributors to tropical rainfall. The ambiguity is worst for convective profile types with radar echo tops within and just above the mixed-phase region. The ability of TMI data (including all low and high frequency polarized brightness temperatures; 19V, 19H, 21V, 37V, 37H, 85V, 85H) to predict vertical structure is assessed. The incremental benefit of including TMI convective/stratiform (C/S) classifiers (both 85 GHz polarization and 19, 37 and 85 GHz texture-based) and LZS lightning observations is then considered. The use of all parameters (brightness temperatures, TMI C/S classifiers, lightning data, predicted vertical structure) to reduce TMI/PR rainfall estimate scatter is demonstrated. For both vertical structure and rainfall estimation, inclusion of C/S classifiers and lightning observations provide statistical skill improvements but do not completely alleviate critical midlevel profile C/S ambiguity and related rain estimate errors.

Boccippio, Dennis↗

TPSAS-NF1676L-29931-DND

The ACE science working group satellite concept calls for a combination of high spectral resolution aerosol lidar and a polarimeter able to determine vertical profiles of aerosol extinction and clouds. Here we discuss why an HSRL lidar is required to achieve these requirements. The primary advantage of an HSRL over an elastic backscatter lidar is that the HSRL channel allows for the independent retrieval of vertically resolved aerosol extinction without constraint. Not requiring a constraint means greater availability of retrievals in polar regions, on the night side, and in broken cloud situations, plus greater accuracy particularly in the lowest part of the atmosphere and in scenes with aerosol heterogeneity. Advantages go beyond the extinction products. Unlike attenuated backscatter, which is an integrated quantity, the aerosol backscatter coefficient depends only on the aerosol at a specific level in the atmosphere, making it preferable for use in quantitative applications. The aerosol backscatter coefficient is more accurate from an HSRL system compared to the retrieval from a single-channel system. This is because errors in both extinction and backscatter from a single-channel system increase with decreasing altitude, due to the need to accurately characterize the overlying attenuation. This means that an HSRL will also have more valid data in and near the boundary layer where aerosol is of primary interest for air quality and weather applications and for many climate objectives including aerosol-cloud interaction studies. Even cloud properties that do not directly use the HSRL capability (cloud phase and thin cirrus retrievals) benefit from the more accurate calibration of an HSRL system. The improved accuracy of backscatter and extinction also lead to better capabilities for aerosol typing, improved retrievals of aerosol radiative effect, and increased information content for combined lidar + polarimeter retrievals of profiles of microphysical properties such as vertically resolved effective radius.

S P Burton↗

Viscous pumping and the spin-down of thermospheric gyres and jets

Strong gyres and jets can be generated at auroral latitudes in the thermosphere by enhanced electric fields during geomagnetic substorms. Typical height profiles of ion density suggest that the ion drag force should generate large curvature in the vertical profile of the winds in the highly viscous region of the thermosphere above about 200 km. It is proposed that the poststorm spin-down of these gyres and jets proceeds via Ekman circulations driven by the curvatures in the height profiles of the winds. Analytic and numerical calculations of the ageostrophic winds forced by curvature in model geostrophic wind profiles show that the ageostrophic wind speeds and directions depend mainly on the kinematic viscosity in the region of curvature and the total change in shear in the geostrophic wind. Ageostrophic wind speeds for typical thermospheric jets can exceed 200 m/s (about 50 percent of the jet winds). Spin-down times of thermospheric jets and cyclonic gyres by the Ekman pumping mechanism are estimated at less than about 6 hours.

Walterscheid, R. L.↗

Atomic oxygen in the lower thermosphere

The 63-micron line due to thermospheric atomic oxygen O(P-3), using a far-infrared spectrometer on a balloon platform at 37 km altitude over Palestine, TX, on June 20, 1983. From measurements of the equivalent width of this line at two elevation angles, a weak angular dependence is found: the equivalent width increases by a factor of 1.5 + or - 0.3 as the angle decreases from +30 deg to +1 deg. Since the optical depth of the O(P-3) line is large, the measured line intensity cannot be directly converted to a column abundance. Instead, the measurements are interpreted in terms of radiative transfer through a 16-layer atmosphere extending to 200 km. A model atmosphere for summer at 30 deg N, with an exospheric temperature of 1300 K, including an assumed daytime atomic oxygen abundance profile constructed from recent chemical and dynamical models and a water vapor abundance profile constructed from recent experimental and model results is used. For this assumed O(P-3) vertical profile shape a multiplicative scaling factor of 0.8, with an altitude-dependent uncertainty is determined. In the best-determined layer the uncertainty in the multiplier is + or - 0.2 at 119 km. The model-dependent peak atomic oxygen density is 3.6 (+ or - 1.9) x 10 to the 11th/cu cm at an altitude of about 101 km.

Lin, Florence J.↗

Investigation of Tropical Dynamics and Transport with UARS Data

Our research focused on Kelvin waves in the tropical lower stratosphere, and resulted in three papers published or submitted to the Journal of Geophysical Research. The first of these, published in 2002, used temperature data from the Microwave Limb Sounder to examine the amplitude, frequency, phase, and spatial structure of leading modes of Kelvin waves. The second and third, submitted late in 2002 and currently in revision, described the response to Kelvin waves of various trace constituents measured by MLS and CLAES (methane, nitrous oxide, CFC-12, and ozone in the second paper; water vapor in the third paper). Water vapor is a special case because the vertical structure induced by Kelvin waves is convolved with water vapor's seasonally varying vertical profile induced by seasonal variations in temperature at the tropical tropopause. Forward modeling indicated that the vertical resolution of MLS was indeed adequate to capture this complicated structure, yet it was not visible in the MLS data, though the Kelvin wave signature was clear on certain UARS levels. The effects of Kelvin waves on the tropical tropopause and on stratosphere- troposphere exchange cannot be quantified from UARS data because of poor vertical resolution and sensitivity in that region. It is recommended that this analysis be repeated using data from the new MLS and HIRDLS instruments aboard Aura, and that priority be given to fine-scale retrievals of temperature, water vapor, and ozone in the tropical tropopause region.

Jackman, Charles↗

Towards an A-train Aerosol Assimilation System: Assimilation of MODIS Aerosol Optical Thickness Retrievals into a Global Aerosol Transport and Radiation Model

To understand the role of atmospheric aerosols in Earth's climate system we ideally require a global, three-dimensional, and temporally continuous system of measurements. The view of aerosols provided by a single polar-orbiting satellite instrument (e.g., MODIS), while providing the greatest spatial coverage of any measurement system available, can offer only a single relevant observation per day of a particular location. Furthermore, the quantitative interpretation of those observations is subject to considerable uncertainty because of we do not know the aerosol optical properties or vertical profiles well enough. Ground-based and in situ measurements can provide missing detail about aerosol vertical and optical properties, but lack the spatial (and sometimes temporal) coverage desired. Chemical transport models treating the aerosol lifecycle complement this picture by providing three-dimensional, global, and continuous aerosol fields, but suffer from poor constraints on their initial conditions (e.g., the aerosol source, sink, and transformation mechanisms). Here we present a global, three- dimensional aerosol transport model and assimilation system. The model assimilates the MODIS aerosol optical thickness product to constrain its aerosol distributions and burdens. We provide an analysis of the model aerosol distributions as constrained by ground-based sun photometer measurements and aerosol products from other satellite measurements.

Colarco, P.↗

Ices in Titan's Lower Stratosphere

Analyses of Cassini CIRS far-infrared limb spectra of Titan at 15N, 15S, and 58S reveal a broad emission feature between 70 and 270/cm, restricted to altitudes between 60 and 100 km. This emission feature is chemically different from Titan's photochemical aerosol, which has an emission feature peak around 145 cm-1. The shape of the observed broad emission feature resembles a mixture of the solid component of the two most abundant nitrites in Titan's stratosphere, that of HCN and HC3N. Following the saturation vapor pressure vertical profiles of HCN and HC3N, the 60 to 100 km altitude range corresponds closely to the vertical location where these nitriles are expected to condense out and form small, suspended ice particles. This is the first time ices in Titan's stratosphere have been identified at latitudes south of 50N. Results and physical implications will be discussed.

Anderson, Carrie↗

Global Weather States and Their Properties from Passive and Active Satellite Cloud Retrievals

In this study, the authors apply a clustering algorithm to International Satellite Cloud Climatology Project (ISCCP) cloud optical thickness-cloud top pressure histograms in order to derive weather states (WSs) for the global domain. The cloud property distribution within each WS is examined and the geographical variability of each WS is mapped. Once the global WSs are derived, a combination of CloudSat and Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) vertical cloud structure retrievals is used to derive the vertical distribution of the cloud field within each WS. Finally, the dynamic environment and the radiative signature of the WSs are derived and their variability is examined. The cluster analysis produces a comprehensive description of global atmospheric conditions through the derivation of 11 WSs, each representing a distinct cloud structure characterized by the horizontal distribution of cloud optical depth and cloud top pressure. Matching those distinct WSs with cloud vertical profiles derived from CloudSat and CALIPSO retrievals shows that the ISCCP WSs exhibit unique distributions of vertical layering that correspond well to the horizontal structure of cloud properties. Matching the derived WSs with vertical velocity measurements shows a normal progression in dynamic regime when moving from the most convective to the least convective WS. Time trend analysis of the WSs shows a sharp increase of the fair-weather WS in the 1990s and a flattening of that increase in the 2000s. The fact that the fair-weather WS is the one with the lowest cloud radiative cooling capability implies that this behavior has contributed excess radiative warming to the global radiative budget during the 1990s.

histograms↗

Global-scale distribution of ozone in the remote troposphere from ATom and HIPPO airborne field missions

Ozone is a key constituent of the troposphere, where it drives photochemical processes, impacts air quality, and acts as a climate forcer. Large-scale in situ observations of ozone commensurate with the grid resolution of current Earth system models are necessary to validate model outputs and satellite retrievals. In this paper, we examine measurements from the Atmospheric Tomography (ATom; four deployments in 2016–2018) and the HIAPER Pole-to-Pole Observations (HIPPO; five deployments in 2009–2011) experiments, two global-scale airborne campaigns covering the Pacific and Atlantic basins. ATom and HIPPO represent the first global-scale, vertically resolved measurements of O3 distributions throughout the troposphere, with HIPPO sampling the atmosphere over the Pacific and ATom sampling both the Pacific and Atlantic. Given the relatively limited temporal resolution of these two campaigns, we first compare ATom and HIPPO ozone data to longer-term observational records to establish the representativeness of our dataset. We show that these two airborne campaigns captured on average 53 %, 54 %, and 38 % of the ozone variability in the marine boundary layer, free troposphere, and upper troposphere–lower stratosphere (UTLS), respectively, at nine well-established ozonesonde sites. Additionally, ATom captured the most frequent ozone concentrations measured by regular commercial aircraft flights in the northern Atlantic UTLS. We then use the repeated vertical profiles from these two campaigns to confirm and extend the existing knowledge of tropospheric ozone spatial and vertical distributions throughout the remote troposphere. We highlight a clear hemispheric gradient, with greater ozone in the Northern Hemisphere, consistent with greater precursor emissions and consistent with previous modeling and satellite studies. We also show that the ozone distribution below 8 km was similar in the extra-tropics of the Atlantic and Pacific basins, likely due to zonal circulation patterns. However, twice as much ozone was found in the tropical Atlantic as in the tropical Pacific, due to well-documented dynamical patterns transporting continental air masses over the Atlantic. Finally, we show that the seasonal variability of tropospheric ozone over the Pacific and the Atlantic basins is driven year-round by transported continental plumes and photochemistry, and the vertical distribution is driven by photochemistry and mixing with stratospheric air. This new dataset provides additional constraints for global climate and chemistry models to improve our understanding of both ozone production and loss processes in remote regions, as well as the influence of anthropogenic emissions on baseline ozone.

ATom, aircraft profiles, Atlantic pollution, ozone↗

An Analysis of the Automated Meteorological Profiling System Low Resolution Flight Element

A study was conducted to determine the quality of thermodynamic and wind data measured by or derived from the Low Resolution Flight Element (LRFE) of the Automated Meteorological Profiling System (AMPS). The AMPS LRFE replaced the Meteorological Sounding System (MSS), which was used to provide vertical profiles of thermodynamic and low-resolution wind data in support of spacecraft launch operations at the Cape Canaveral Air Force Station (CCAFS) and NASA Kennedy Space Center (KSC), Florida. Air temperature, relative humidity, and height, which are directly measured by the LRFE, are used to derive air pressure and density. Test flights were conducted where an LRFE sonde and an MSS sonde were attached to the same balloon and the two profiles were compared. MSS data was used as the standard reference data. The objective of the thermodynamic testing was to determine a) if the LRFE met Space Shuttle Program (SSP) accuracy requirements outlined in the Space Shuttle Launch and Landing Program Requirements Document (PRD) and/or, b) if the LRFE met or exceeded MSS data quality. AMPS uses the Global Positioning System (GPS) to determine wind speed and direction. In order to provide a basis for comparison, either an AMPS High Resolution Flight Element (HRFE) or a radar tracked Jimsphere was released simultaneously with each AMPS LRFE at CCAFS. The goal of these tests was to determine if the LRFE wind data met the requirement for low-resolution wind data defined in the Shuttle PRD. Based on the available data, the LRFE is shown to produce more consistent thermodynamic measurements than the MSS. The LRFE is also shown to meet the Shuttle PRD requirements for low resolution wind data.

Leahy, Frank B.↗