Search NASA⌕ Search

SEARCH · Search NASA

Results for “3D electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Multivalence states and optical band-tail effect in heavily V-doped ZnS thin films

V K-edge X-ray absorption near edge structure spectroscopy analysis of Zn 1-x V x S demonstrates that the bulk V valence states change from V(IV) to V(II) as the V concentration increases from x=0.15 to x=0.48. Atomic bound-state transitions from the hybridization of sp ZnS and 3d V electronic states show a decreasing hybridization with V concentration. X-ray photoelectron spectroscopy reveals the coexistence of a V(IV)/V(III)/V(II) mixture at the surface with a predominant V(III) state, indicating differences between surface and bulk. Optical studies reflect large band-tails associated with in-gap defects that increase with V concentration.

36 MATERIALS SCIENCE↗

Pool boiling critical heat flux studies of accident tolerant fuel cladding materials

Pool boiling experiments have been performed at atmospheric pressure on potential accident tolerant fuel (ATF) cladding materials (Zirlo®, Cr coated Zirlo®, FeCrAl coated Zirlo®, and monolithic SiC) to evaluate the Critical Heat Flux (CHF) points. Corrosion resistant coatings of Cr and FeCrAl alloy were deposited on flat Zirlo® samples using cold spray technology. The as-prepared samples after uniform surface polishing were subjected to autoclave tests at 360 °C water and 18.6 MPa for 360 h to simulate prototypic corrosion of the ATF cladding materials in LWR normal operation. Surface characteristics potentially influencing CHF such as surface morphology, roughness, static contact angle, and surface chemistry were characterized using a suite of characterization methods including scanning electron microscopy, 3D optical profilometry, optical contact angle measurements, and x-ray photoelectron spectroscopy (XPS). Thermo-physical properties of the samples such as density, thermal conductivity, and heat capacity were measured by differential scanning calorimetry and laser flash thermal diffusivity measurement. FeCrAl coatings showed CHF values comparable to bare Zirlo® samples, while slightly lower CHF values were observed for Cr coated samples and bulk SiC flats (produced by chemical vapor deposition, CVD). As-deposited Cr coatings showed 67% higher CHF than the as-polished Cr coatings due to its higher surface roughness level. The autoclave testing for the prepared samples generally increased the CHF except for the surface polished Cr coatings. Similar CHF values of bare Zirlo®, FeCrAl coating, and CVD SiC samples were observed after autoclave test but there were negligible change CHF of Cr coatings. XPS studies indicated that the formation or deposition of a few monolayers of hydrophobic carbonaceous species on surface can affect CHF values. The trends in CHF data are discussed in terms of evolution of the surface characteristics of the ATF materials.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Enhancing Magnetic Functionality with Scandium: Breaking Stereotypes in the Design of Rare Earth Materials

Replacement of strongly magnetic gadolinium with weakly magnetic scandium unexpectedly enhances ferromagnetic interactions in (Gd 1–x Sc x ) 5 Ge 4 . Based upon this counterintuitive experimental finding we demonstrate the unique role 3d 1 electrons of scandium atoms play in mediating magnetic interactions between the gadolinium atoms from the neighboring layers in the Sm 5 Ge 4 -type crystal lattice. Scandium substitutions at and below 20% rapidly increase the Curie temperature, TC, of the Gd 5 Ge 4 parent, eliminate both the kinetic arrest and hysteresis, and drastically improve reversibility of the first-order magnetostructural transformation at T C . In agreement with first-principles predictions, higher than 20% Sc leads to the formation of a closely related Pu 5 Rh 4 -type structure where the first-order magnetostructural transformation is replaced by a conventional second-order ferromagnetic ordering that remains accompanied by a continuous rearrangement of the crystal lattice. In conclusion, comparison of two materials with similar structures and compositions shows that significantly stronger magnetocaloric effect occurs in the first-order material, which also shows very small hysteresis. Furthermore, we demonstrate that a behavior of a specific interatomic distance can predict anomalous physical properties in a series of alloys where compositional dependence of lattice parameters suggests a rather trivial solid solubility and uninteresting magnetism.

36 MATERIALS SCIENCE↗

Synthesis and Characterization of Metastable Cobalt Honeycomb KCoAsO 4

The Kitaev model has served as a long-sought-after target in the realization of a quantum spin liquid that could host Majorana Fermions. Such non-Abelian anyons could revolutionize quantum computing if properly implemented to overcome decoherence. A 3d 7 electronic configuration, like Co 2+ , has been explored by theory and experimental work to design Kitaev materials. Here, in this study, we report the synthesis of a new cobaltate honeycomb material KCoAsO 4 . The compound is synthesized through a low-temperature solution route and crystallized in space group R¯3 with lattice parameters a = 5.0394(1) and c = 28.6790(1) as determined by neutron powder diffraction. The crystal structure follows motifs similar to those of the honeycomb compound BaCo2(AsO 4 ) 2 but presents differing magnetic behavior. Magnetization/heat capacity measurements on the powder show antiferromagnetic transition T N = 14 K. Two lower-temperature transitions are present in susceptibility at low field that resemble spin reorientations. Magnetization data as a function of field have curvature indicative of metamagnetic behavior below the magnetic ordering temperature, with the magnetic ordering suppressed upon application of a higher magnetic field. Computational studies suggest the presence of a weak nearest-neighbor Kitaev term, K 1 , consistent with related honeycomb cobaltates. Together, the data suggest that this material should present a new platform for developing Kitaev quantum spin liquids.

cobaltate↗

Derivation of Multiple Covarying Material and Process Parameters Using Physics-Based Modeling of X-ray Data

There is considerable interest in developing multimodal characterization frameworks capable of probing critical properties of complex materials by relying on distinct, complementary methods or tools. Any such framework should maximize the amount of information that is extracted from any given experiment and should be sufficiently powerful and efficient to enable on-the-fly analysis of multiple measurements in a self-consistent manner. Such a framework is demonstrated in this work in the context of self-assembling polymeric materials, where theory and simulations provide the language to seamlessly mesh experimental data from two different scattering measurements. Specifically, the samples considered here consist of diblock copolymers (BCP) that are self-assembled on chemically nanopatterned surfaces. The copolymers microphase separate into ordered lamellae with characteristic dimensions on the scale of tens of nanometers that are perfectly aligned by the substrate over macroscopic areas. These aligned lamellar samples provide ideal standards with which to develop the formalism introduced in this work and, more generally, the concept of high-information-content, multimodal experimentation. In conclusion, the outcomes of the proposed analysis are then compared to images generated by 3D scanning electron microscopy tomography, serving to validate the merit of the framework and ideas proposed here.

36 MATERIALS SCIENCE↗

In Situ Local Imaging of Ferromagnetism and Superconductivity in RbEuFe 4 As 4

The coexistence of superconductivity and ferromagnetism is an intrinsically interesting research focus in condensed matter physics but the study is limited by low superconducting (T c ) and magnetic (T m ) transition temperatures in related materials. Here, we used a scanning superconducting quantum interference device to image the in-situ diamagnetic and ferromagnetic responses of RbEuFe 4 As 4 with high T c and T m . We observed significant suppression of superfluid density in vicinity of the magnetic phase transition, signifying fluctuation-enhanced magnetic scatterings between Eu spins and Fe 3d conduction electrons. Intriguingly, we observed multiple ferromagnetic domains which should be absent in an ideal magnetic helical phase. The formation of these domains demonstrates a weak c-axis ferromagnetic component probably arising from Eu spin-canting effect, indicative of possible superconductivity-driven domain Meissner and domain vortex-antivortex phases as revealed in EuFe 2 (As 0.79 P 0.21 ) 2 . Finally, our observations highlight RbEuFe 4 As 4 is a unique system which includes multiple interplay channels between superconductivity and ferromagnetism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

ITQ-54: a multi-dimensional extra-large pore zeolite with 20 × 14 × 12-ring channels

A multi-dimensional extra-large pore silicogermanate zeolite, named ITQ-54, has been synthesised by in situ decomposition of the N,N-dicyclohexylisoindolinium cation into the N-cyclohexylisoindolinium cation. Its structure was solved by 3D rotation electron diffraction (RED) from crystals of ca. 1 μm in size. The structure of ITQ-54 contains straight intersecting 20 × 14 × 12-ring channels along the three crystallographic axes and it is one of the few zeolites with extra-large channels in more than one direction. ITQ-54 has a framework density of 11.1 T atoms per 1000 Å 3 , which is one of the lowest among the known zeolites. ITQ-54 was obtained together with GeO 2 as an impurity. A heavy liquid separation method was developed and successfully applied to remove this impurity from the zeolite. ITQ-54 is stable up to 600 °C and exhibits permanent porosity. The structure was further refined using powder X-ray diffraction (PXRD) data for both as-made and calcined samples.

36 MATERIALS SCIENCE↗

Linking morphology with activity through the lifetime of pretreated PtNi nanostructured thin film catalysts

In this study, the nanoscale morphology of highly active Pt 3 Ni 7 nanostructured thin film fuel cell catalysts is linked with catalyst surface area and activity following catalyst pretreatments, conditioning and potential cycling. The significant role of fuel cell conditioning on the structure and composition of these extended surface catalysts is demonstrated by high resolution imaging, elemental mapping and tomography. The dissolution of Ni during fuel cell conditioning leads to highly complex, porous structures which were visualized in 3D by electron tomography. Quantification of the rendered surfaces following catalyst pretreatment, conditioning, and cycling shows the important role pore structure plays in surface area, activity, and durability.

30 DIRECT ENERGY CONVERSION↗

The migration mechanism of transition metal ions in LiNi 0.5 Mn 1.5 O 4

The migration of transition metal ions in the oxygen framework was recently proposed to be responsible for the continuous loss of average working potential of high energy density layered–layered composite cathodes for lithium-ion batteries. The potential migration pathway in a model material, LiNi 0.5 Mn 1.5 O 4 spinel, was investigated using in situ high-energy X-ray diffraction and in situ neutron diffraction during the solid state synthesis process. It was found that the migration of transition metal ions among octahedral sites is possible by using tetrahedral vacancies as intermediate sites. It was also suggested that the number of electrons in 3d orbitals has a significant impact on their mobility in the hosting oxygen framework.

25 ENERGY STORAGE↗

Gd 3 Ni 2 and Gd 3 Co x Ni 2-x : magnetism and unexpected Co/Ni crystallographic ordering

The crystal structure, composition and physical properties of Gd 3 Ni 2 , which was earlier reported to exist in the Gd–Ni system without any details of its structure and properties, have been determined. This rare earth binary compound is a high-temperature phase: it forms via a peritectic reaction at 988 K (715 °C) and decomposes below ≈923 K (650 °C). The compound can be retained at room temperature as a metastable phase by quenching after high temperature annealing. Gd 3 Ni 2 crystallizes in the monoclinic Dy 3 Ni 2 structure type [mS20, C2/m (No. 12), Z = 4; with lattice parameters a = 13.418(3) Å, b = 3.720(1) Å, c = 9.640(2) Å, β = 106.250(3)°]. Ni can be substituted by Co up to 50% (i.e. up to and including Gd 3 CoNi) with no change in the structural prototype; the substitution of Co for Ni stabilizes the R 3 Co x Ni 2-x phases down to room temperature. The crystal structure, magnetic properties and magnetocaloric effect (MCE) have been investigated for both Gd 3 Ni 2 and the related Gd 3 Co x Ni 2-x solid solution alloys (0 ≤ x ≤ 1). The crystal structure of the Gd 3 CoNi is a ternary ordered derivative of the monoclinic Dy 3 Ni 2 -type, where Co fully occupies only one of the two 4i Wyckoff sites available for the transition metal. To the best of our knowledge, this is the first example of an intermetallic phase showing ordered site occupations by the chemically quite similar elements Co and Ni. All compounds show long range ferromagnetic ordering, with T C progressively increasing from 147 K (for Gd 3 Ni 2 ) to 176 K (for Gd 3 CoNi) as a cubic function of the Co content. Evidence of Co contributing to the magnetic interactions in these compounds has been found. First-principles total energy calculations predicted the ordered occupation of Co and Ni at the crystallographic sites of Gd3CoNi, which was later confirmed by single crystal X-ray diffraction. The increased conduction electronic state (3d) exchange splitting at the Fermi level supports the experimentally observed enhanced Curie temperature in Gd 3 CoNi compared to Gd 3 Ni 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metal-hydrogen-pi-bonded organic frameworks

We report the synthesis and characterization of a new series of permanently porous, three-dimensional metal–organic frameworks (MOFs), M-HAF-2 (M = Fe, Ga, or In), constructed from tetratopic, hydroxamate-based, chelating linkers. Here, the structure of M-HAF-2 was determined by three-dimensional electron diffraction (3D ED), revealing a unique interpenetrated hcb-a net topology. This unusual topology is enabled by the presence of free hydroxamic acid groups, which lead to the formation of a diverse network of cooperative interactions comprising metal–hydroxamate coordination interactions at single metal nodes, staggered π–π interactions between linkers, and H-bonding interactions between metal-coordinated and free hydroxamate groups. Such extensive, multimodal interconnectivity is reminiscent of the complex, noncovalent interaction networks of proteins and endows M-HAF-2 frameworks with high thermal and chemical stability and allows them to readily undergo postsynthetic metal ion exchange (PSE) between trivalent metal ions. We demonstrate that M-HAF-2 can serve as versatile porous materials for ionic separations, aided by one-dimensional channels lined by continuously π-stacked aromatic groups and H-bonding hydroxamate functionalities. As an addition to the small group of hydroxamic acid-based MOFs, M-HAF-2 represents a structural merger between MOFs and hydrogen-bonded organic frameworks (HOFs) and illustrates the utility of non-canonical metal-coordinating functionalities in the discovery of new bonding and topological patterns in reticular materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Current disruption and its spreading in collisionless magnetic reconnection

Recent magnetic reconnection experiments (MRX) [Dorfman et al., Geophys. Res. Lett. 40, 233 (2013)] have disclosed current disruption in the absence of an externally imposed guide field. During current disruption in MRX, both the current density and the total observed out-of-reconnection-plane current drop simultaneous with a rise in out-of-reconnection-plane electric field. Here, we show that current disruption is an intrinsic property of the dynamic formation of an X-point configuration of magnetic field in magnetic reconnection, independent of the model used for plasma description and of the dimensionality (2D or 3D) of reconnection. An analytic expression for the current drop is derived from Ampere's Law. Its predictions are verified by 2D and 3D electron-magnetohydrodynamic (EMHD) simulations. Three dimensional EMHD simulations show that the current disruption due to localized magnetic reconnection spreads along the direction of the electron drift velocity with a speed which depends on the wave number of the perturbation. The implications of these results for MRX are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma kinetic effects on interfacial mix and burn rates in multispatial dimensions

The physics of mixing in plasmas is of great significance to inertial confinement fusion and high energy density laboratory experiments. Two- and three-dimensional (2D and 3D) particle-in-cell simulations with a binary collision model are used to explore kinetic effects arising during the mixing of plasma media. The applicability of the one-dimensional (1D) ambipolarity condition is evaluated in 2D and 3D simulations of a plasma interface with a sinusoidal perturbation. The 1D ambipolarity condition is found to remain valid in 2D and 3D, as electrons and ions flow together required for $J$ = 0. Simulations of perturbed interfaces show that diffusion-induced total pressure imbalance and hydroflows flatten fine interface structures and drive rapid atomic mix. The atomic mix rate from a structured interface is faster than the ~$\sqrt{\bar{t}}$ scaling obtained from 1D theory in the small-Knudsen-number limit. Plasma kinetic effects inhibit the growth of the Rayleigh-Taylor instability at small wavelengths and result in a nonmonotonic growth rate scaling with wavenumber k with a maximum at a low k value, much different from $\sqrt{Agk}$ (where A is the Atwood number and g is the gravitational constant) as expected in the absence of plasma kinetic effects. Simulations under plasma conditions relevant to MARBLE separated-reactant experiments on Omega and the NIF show kinetic modification of DT fusion reaction rates. With non-Maxwellian distributions and relative drifts between D and T ions, DT reactivity is higher than that inferred from rates using stationary Maxwellian distributions. Reactivity is additionally revealed to be reduced in the presence of finite-Knudsen-layer losses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

3D velocity map imaging of electrons with TPX3CAM

In this report we demonstrate three-dimensional velocity map imaging of low energy electrons using a TPX3CAM, where the three-dimensional momentum information [$p_x, p_y, p_z$] is encoded in position and timing [x, y, t] of hits on the camera sensor. We make use of the camera sensor for the [x, y] information and a constant fraction discriminator and fast time to digital converter in the camera for the time information. We illustrate the capabilities of our apparatus by presenting above threshold ionization measurements of xenon, which produces well defined structures in the momentum resolved photoelectron yield.

79 ASTRONOMY AND ASTROPHYSICS↗

Spin-crossover complexes: Self-interaction correction vs density correction

Complexes containing a transition metal atom with a 3d 4 –3d 7 electron configuration typically have two low-lying, high-spin (HS) and low-spin (LS) states. The adiabatic energy difference between these states, known as the spin-crossover energy, is small enough to pose a challenge even for electronic structure methods that are well known for their accuracy and reliability. In this work, we analyze the quality of electronic structure approximations for spin-crossover energies of iron complexes with four different ligands by comparing energies from self-consistent and post-self-consistent calculations for methods based on the random phase approximation and the Fermi–Löwdin self-interaction correction. Considering that Hartree–Fock densities were found by Song et al., J. Chem. Theory Comput. 14, 2304 (2018), to eliminate the density error to a large extent, and that the Hartree–Fock method and the Perdew–Zunger-type self-interaction correction share some physics, we compare the densities obtained with these methods to learn their resemblance. Here, we find that evaluating non-empirical exchange-correlation energy functionals on the corresponding self-interaction-corrected densities can mitigate the strong density errors and improves the accuracy of the adiabatic energy differences between HS and LS states.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Iron telluride ladder compounds: Predicting the structural and magnetic properties of BaFe 2 Te 3

Since the discovery of pressure-induced superconductivity in the two-leg ladder system BaFe 2 X 3 (X=S, Se), with the 3d iron electronic density n=6, quasi-one-dimensional iron-based ladders have attracted considerable attention. In this work, we use density-functional theory to predict that the novel n=6 iron ladder BaFe 2 Se 3 could be stable with a similar crystal structure as BaFe 2 Se 3 . Furthermore, our results also indicate that BaFe2Te3 will display a complex 2×2 block-type magnetic order. Due to the magnetic striction effects of this block order, BaFe2Te3 should be a magnetic noncollinear ferrielectric system with a net polarization 0.31μC/cm2. In summary, the similar electronic density and magnetic ground state of Te- and Se-based ladders indicates both should display similar properties. In particular, the physical and structural similarity with BaFe 2 Se 3 suggests that BaFe 2 Se 3 could become superconducting under high pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Origin of the magnetic and orbital ordering in α-Sr 2 CrO 4

Motivated by recent experimental progress in transition metal oxides with the K 2 NiF 4 structure, in this study we investigate the magnetic and orbital ordering in α-Sr 2 CrO 4 . Using first principles calculations, first we derive a three-orbital Hubbard model, which reproduces the ab initio band structure near the Fermi level. The unique reverse splitting of t 2g orbitals in α-Sr 2 CrO 4 , with the 3d 2 electronic configuration for the Cr 4+ oxidation state, opens up the possibility of orbital ordering in this material. Using real-space Hartree-Fock for multi-orbital systems, we constructed the ground state phase diagram for the two dimensional compound α-Sr 2 CrO 4 . We found stable ferromagnetic, antiferromagnetic, antiferro-orbital, and staggered orbital stripe ordering in robust regions of the phase diagram. Furthermore, using the density matrix renormalization group method for two-leg ladders with the realistic hopping parameters of α-Sr 2 CrO 4 , we explore magnetic and orbital ordering for experimentally relevant interaction parameters. Again, we find a clear signature of antiferromagnetic spin ordering along with antiferro-orbital ordering at moderate to large Hubbard interaction strength. We also explore the orbital-resolved density of states with Lanczos, predicting insulating behavior for the compound α-Sr 2 CrO 4 , in agreement with experiments. Finally, an intuitive understanding of the results is provided based on a hierarchy between orbitals, with d xy driving the spin order, while electronic repulsion and the effective one dimensionality of the movement within the d xz and d yz orbitals driving the orbital order.

36 MATERIALS SCIENCE↗

Peierls transition, ferroelectricity, and spin-singlet formation in monolayer VOI 2

Using ab initio density functional theory and single-orbital Hubbard model calculations via the density matrix renormalization group method, we systematically studied the monolayer VOI 2 with a 3d 1 electronic configuration. Our phonon calculations indicate that the orthorhombic Pmm2 FE-II phase is the most likely ground state, involving a ferroelectric (FE) distortion along the a axis and V-V dimerization along the b axis. Specifically, the “pseudo Jahn-Teller” effect caused by the coupling between empty V (d xz/yz and d 3z 2 -r 2 ) and O 2p states is proposed as the mechanism that stabilizes the FE distortion from the paraelectric phase. Moreover, the half-filled metallic d xy band displays a Peierls instability along the b axis, inducing a V-V dimerization. Additionally, we found very short-range antiferromagnetic coupling along the V-V chain due to the formation of nearly decoupled spin singlets in the ground state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗