SEARCH · Search NASA

Results for “Active Flow Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Wave phenomena in a high Reynolds number compressible boundary layer

Growth of unstable disturbances in a high Reynolds number compressible boundary layer is numerically simulated. Localized periodic surface heating and cooling as a means of active control of these disturbances is studied. It is shown that compressibility in itself stabilizes the flow but at a lower Mach number, significant nonlinear distortions are produced. Phase cancellation is shown to be an effective mechanism for active boundary layer control.

Bayliss, A.↗

NASA NTRS2003

Boundary-Layer Separation Control under Low-Pressure Turbine Airfoil Conditions using Glow-Discharge Plasma Actuators

Modem low-pressure turbines, in general, utilize highly loaded airfoils in an effort to improve efficiency and to lower the number of airfoils needed. Typically, the airfoil boundary layers are turbulent and fully attached at takeoff conditions, whereas a substantial fraction of the boundary layers on the airfoils may be transitional at cruise conditions due to the change of density with altitude. The strong adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation at the latter low Reynolds number conditions. Large separation bubbles, particularly those which fail to reattach, cause a significant degradation of engine efficiency. A component efficiency drop of the order 2% may occur between takeoff and cruise conditions for large commercial transport engines and could be as large as 7% for smaller engines at higher altitude. An efficient means of of separation elimination/reduction is, therefore, crucial to improved turbine design. Because the large change in the Reynolds number from takeoff to cruise leads to a distinct change in the airfoil flow physics, a separation control strategy intended for cruise conditions will need to be carefully constructed so as to incur minimum impact/penalty at takeoff. A complicating factor, but also a potential advantage in the quest for an efficient strategy, is the intricate interplay between separation and transition for the situation at hand. Volino gives a comprehensive discussion of several recent studies on transition and separation under low-pressure-turbine conditions, among them one in the present facility. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions. If the transition occurs early in the boundary layer then separation may be reduced or completely eliminated. Transition in the shear layer of a separation bubble can lead to rapid reattachment. This suggests using control mechanisms to trigger and enhance early transition. Gad-el-Hak provides a review of various techniques for flow control in general and Volino discusses recent studies on separation control under low-pressure-turbine conditions utilizing passive as well as active devices. As pointed out by Volino, passive devices optimized for separation control at low Reynolds numbers tend to increase losses at high Reynolds numbers, Active devices have the attractive feature that they can be utilized only in operational regimes where they are needed and when turned off would not affect the flow. The focus in the present paper is an experimental Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modem low-pressure-turbine airfoil ('Pak-B'). The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2%) and high (2.5%) Gee-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface- flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control. of active separation control using glow discharge plasma actuators.

Hultgren, Lennart S.↗

NASA NTRS1976

Airframe technology for energy efficient transport aircraft

NASA has initiated a comprehensive Aircraft Energy Efficiency Program which is concerned with the development of approaches for reducing fuel consumption in new aircraft of the 1980-2000 time period. A review is presented of the airframe technologies selected for emphasis in the NASA program, taking into account an evaluation of their potential for reducing transport direct operating costs through fuel efficiency. Attention is given to the importance of fuel efficiency, the impact of advanced technology, advanced composite structures, the NASA composite primary structures program, advanced aerodynamics and active controls, supercritical wing geometry, active load and flutter control, and aspects of laminar flow control.

Leonard, R. W.↗

NASA NTRS1985

Numerical simulation of boundary layer excitation by surface heating/cooling

The concept of active control of growing disturbances in an unstable compressible flow by using time periodic, localized surface heating is studied numerically. The simulations are calculated by a fourth-order accurate solution of the compressible, laminar Navier-Stokes equations. Fourth-order accuracy is particularly important for this problem because the solution must be computed over many wavelengths. The numerical results demonstrate the growth of an initially small fluctuation into the nonlinear regime where a local breakdown into smaller scale disturbances can be observed. It is shown that periodic surface heating over a small strip can reduce the level of the fluctuation provided that the phase of the heating current is properly chosen.

Bayliss, A.↗

NASA NTRS1986

Numerical simulation of boundary-layer excitation by surface heating/cooling

Bayliss, A.↗

NASA NTRS1989

Adaptive structures; Proceedings of the ASME Winter Annual Meeting, San Francisco, CA, Dec. 10-15, 1989

The present conference on adaptive structures discusses piezoelectric and electrostrictive sensors and actuators for adaptive structures and smart materials, real-time control for composite structures with embedded actuators and sensors, a laminated-shell theory incorporating embedded distributed actuators, traveling-wave power flow techniques, uncertainty modeling for the control of an active structure, and active vibration isolation in the presence of unmodeled structural dynamic response. Also discussed are the control of flexible beams via free-free active truss, truss structure control using member actuators with latch mechanism, neural processors for smart-structure control, the effect of imperfections on the static control of adaptive structures, adaptive structures for segmented optical systems, and the shape-control of flexible structures.

Wada, Ben K.↗

NASA NTRS2002

Integrated Shear Stress/Temperature Micromachined Sensors

During this project we were able to design and initiate the fabrication of an integrated Micro ElectroMechanical Systems (MEMS)-based shear stress/temperature sensor for flow control applications. A brief summary of the completed activities during this project is presented.

Sheplak, Mark↗

NASA NTRS2013

Physics Based Model for Online Fault Detection in Autonomous Cryogenic Loading System

We report the progress in the development of the chilldown model for rapid cryogenic loading system developed at KSC. The nontrivial characteristic feature of the analyzed chilldown regime is its active control by dump valves. The two-phase flow model of the chilldown is approximated as one-dimensional homogeneous fluid flow with no slip condition for the interphase velocity. The model is built using commercial SINDAFLUINT software. The results of numerical predictions are in good agreement with the experimental time traces. The obtained results pave the way to the application of the SINDAFLUINT model as a verification tool for the design and algorithm development required for autonomous loading operation.

Cryogenics↗

NASA NTRS1996

A New Method for the Adaptive Control of Vortex-Wall Interactions

The control of vortical flows is gaining significance in the design of aeronautical and marine structures. While passive devices have been used effectively in the past, active control strategies have the potential of allowing a leap in the performance of future configurations. The efficiency of control schemes is strongly dependent on the development of accurate flow models that can be devised using information that is available not only from numerical solutions of the governing Navier-Stokes equations but also can be measured experimentally. In that context it is desirable to construct adaptive control schemes using information that can be measured at the wall.

Koumoutsakos, P.↗

NASA NTRS2007

Living Together in Space: The International Space Station Internal Active Thermal Control System Issues and Solutions-Sustaining Engineering Activities at the Marshall Space Flight Center From 1998 to 2005

On board the International Space Station, heat generated by the crew and equipment is removed by the internal active thermal control system to maintain a comfortable working environment and prevent equipment overheating. Test facilities simulating the internal active thermal control system (IATCS) were constructed at the Marshall Space Flight Center as part of the sustaining engineering activities to address concerns related to operational issues, equipment capability, and reliability. A full-scale functional simulator of the Destiny lab module IATCS was constructed and activated prior to launch of Destiny in 2001. This facility simulates the flow and thermal characteristics of the flight system and has a similar control interface. A subscale simulator was built, and activated in 2000, with special attention to materials and proportions of wetted surfaces to address issues related to changes in fluid chemistry, material corrosion, and microbial activity. The flight issues that have arisen and the tests performed using the simulator facilities are discussed in detail. In addition, other test facilities at the MSFC have been used to perform specific tests related to IATCS issues. Future testing is discussed as well as potential modifications to the simulators to enhance their utility.

Wieland, P. O.↗

NASA NTRS1980

On the stabilization of three-dimensional boundary layers by suction and cooling

A significant reduction in the drag of transonic aircraft can be achieved by using an active method of boundary-layer control to maintain laminar flow on the aerodynamic surfaces. The stabilizing influence of suction for both favorable and adverse pressure gradients is demonstrated by means of the self-similar incompressible three-dimensional boundary layers on yawed wedges. Profile instability is measured by the maximum amplification rate of fixed-frequency disturbances computed according to linearized, locally parallel, spatial stability theory. Suction is found to be more effective in controlling Tollmien-Schlichting instability than stationary cross-flow disturbances. The effectiveness of surface cooling as a method of stabilization is compared with suction for the boundary layers on a transonic 35 deg swept wing of infinite span. It is found from compressible stability theory that when the surface is cooled to a uniform temperature such that the maximum cross-flow velocity is reduced by the same amount as with a uniform suction distribution, the stabilizing effect of cooling on cross-flow disturbances is less than with suction.

Mack, L. M.↗

NASA NTRS1984

Development of flight testing techniques

A list of students involved in research on flight analysis and development is given along with abstracts of their work. The following is a listing of the titles of each work: Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft; Aerodynamic drag reduction tests on a box shaped vehicle; A microprocessor based anti-aliasing filter for a PCM system; Flutter prediction of a wing with active aileron control; Comparison of theoretical and flight measured local flow aerodynamics for a low aspect ratio fin; In flight thrust determination on a real time basis; A comparison of computer generated lift and drag polars for a Wortmann airfoil to flight and wind tunnel results; and Deep stall flight testing of the NASA SGS 1-36.

Sandlin, D. R.↗

NASA NTRS1991

Status and outlook of flow separation control

Under certain conditions, wall-bounded flows separate. To improve the performance of natural or man-made flow systems, it may be beneficial to delay or advance this detachment process. The present article reviews the status and outlook of separation control for both steady and unsteady flows. Both passive and active techniques to prevent or to provoke flow detachment are considered and suggestions are made for further research.

Gad-El-hak, Mohamed↗

NASA NTRS1997

A review of adaptive change in musculoskeletal impedance during space flight and associated implications for postflight head movement control

We present a review of converging sources of evidence which suggest that the differences between loading histories experienced in 1-g and weightlessness are sufficient to stimulate adaptation in mechanical impedance of the musculoskeletal system. As a consequence of this adaptive change we argue that we should observe changes in the ability to attenuate force transmission through the musculoskeletal system both during and after space flight. By focusing attention on the relation between human sensorimotor activity and support surfaces, the importance of controlling mechanical energy flow through the musculoskeletal system is demonstrated. The implications of such control are discussed in light of visual-vestibular function in the specific context of head and gaze control during postflight locomotion. Evidence from locomotory biomechanics, visual-vestibular function, ergonomic evaluations of human vibration, and specific investigations of locomotion and head and gaze control after space flight, is considered.

Review, Tutorial↗

NASA NTRS2013

Towed Subsurface Optical Communications Buoy

The innovation allows critical, high-bandwidth submarine communications at speed and depth. This reported innovation is a subsurface optical communications buoy, with active neutral buoyancy and streamlined flow surface veins for depth control. This novel subsurface positioning for the towed communications buoy enables substantial reduction in water-absorption and increased optical transmission by eliminating the intervening water absorption and dispersion, as well as by reducing or eliminating the beam spread and the pulse spreading that is associated with submarine-launched optical beams.

Stirbl, Robert C.↗

NASA NTRS1991

Transonic adaptive flutter suppression using approximate unsteady time domain aerodynamics

A digital adaptive controller is applied to the active flutter suppression problem of a wing under time varying flight conditions in subsonic and transonic flow. Linear quadratic controller gain at each time step is obtained using an iterative Riccati solver. The digital adaptive optimal controller is robust with respect to the unknown external loads. Flutter and divergence instabilities are simultaneously suppressed using a trailing-edge control surface and displacement sensing. A new transonic unsteady aerodynamic approximation methodology is developed which enables one to carry out the rapid calculation required for transonic aeroservoelastic applications. This approximation is based on a combination of unsteady subsonic aerodynamics combined with a transonic correction procedure. Aeroservoelastic transient time response is obtained using Roger's approximation, state transition matrices and an iterative time marching algorithm. The aeroservoelastic system in the time domain is modeled using a deterministic ARMA model together with a parameter estimator. Transonic flutter boundaries of a wing structure are computed, in the time domain, using an estimated aeroelastic system matrix and are in good agreement with experimental data for the low transonic Mach number range.

Pak, Chan-Gi↗

NASA NTRSDate not supplied

Hall Magnetohydrodynamic Power Generation and Drag Augmentation Using A Coaxial-Electrode Configuration During Hypersonic Entry

For interplanetary missions, a spacecraft must reduce its relative velocity from orbital speeds of multiple kilometers per second to zero in order to safely land on the surface of a planetary body. During this phase known as planetary reentry, the spacecraft undergoes high speed above Mach 5 up to Mach 30. This hyper-sonic flight regime imposes a strong bow shock in front of the vehicle that imparts extreme aerodynamic and thermal effects. In addition, during portions of this regime, a plasma is formed in the post-shock flow-field around the vehicle due to these high temperatures. Interaction between an applied magnetic field with this electrically conductive fluid, or magnetohydrodynamic (MHD) interaction, can be utilized to convert kinetic energy from the flow into storable electrical energy. Onboard MHD energy generation can benefit the spacecraft by increasing the power of active thermal control components and vehicle control systems during reentry. MHD interaction also exerts a Lorentz body force on the plasma flow that can be manipulated to act as an additional drag force through the vehicle body. MHD drag augmentation can benefit the spacecraft with an additional control mechanism that operates without moving parts. This can be utilized at higher altitudes and subsequently reduce convective heat transfer to the vehicle. MHD interaction with plasma flow suggests that both power generation and drag augmentation can be integrated together in one design. Modern numerical studies have only demonstrated the viability and potential of MHD energy generation and drag modulation separately for implementation into future spacecraft designs [1] [2] [3]. Steeves et. al. presented one possible generator design specifically for reentry vehicles that utilized a modular panel with two embedded electromagnets and two extruding electrodes for air plasma to flow between. Fujino et. al. presented results that indicated increased total drag with a permanent magnet embedded in the blunt body of the Orbital Reentry Experiment (OREX) trajectory. Furthermore, experimental investigations of these two MHD applications have been limited and separate due to the difficult technical nature of experimental de-sign and analysis. For MHD energy generation, there have been two designs which used a cylindrical fore-body with two embedded permanent magnets and two outward facing curved electrodes for tangency to an artificially ionized plasma that flowed along the body length [4] [5]. The first design was studied using an air microwave (MW) ionized supersonic plasma wind tunnel and the second design used radio frequency (RF) ionization of Argon, but both physically demonstrated the feasibility of MHD energy generation in reentry plasma conditions. For MHD drag modulation, one study involved a small-scale cylindrical blunt body embedded with permanent magnets immersed in plasma flow in an arcjet tunnel [6], and another utilized a spherical permanent magnet enclosed with a spherical forebody that was evaluated in a shock expansion tunnel [7]. Both experimental studies provided physical evidence of drag augmentation due to MHD interactions. Therefore, because of the multi-faceted effects of MHD along with both applications having been deemed feasible and beneficial during reentry, this indicates that a coupled power generation and drag modulation design could be achievable. The axi-symmetric nature of blunt bodies for reentry suggests that a spherical set of two ring electrodes near the nose along the body axis. Based on first principles, flow along the walls of the spherical body can then produce MHD interactions between the electrodes. As a result, two currents are generated: a Hall current that produces power and a primary inductive current that augments the drag force. The goal of this work is to provide a simulated design of a coaxial-electrode con-figuration for power generation and drag modulation for experimental testing.

E. Leong↗

NASA NTRS2016

Engineering Design Tools for Shape Memory Alloy Actuators: CASMART Collaborative Best Practices and Case Studies

The primary goal of the Consortium for the Advancement of Shape Memory Alloy Research and Technology (CASMART) is to enable the design of revolutionary applications based on shape memory alloy (SMA) technology. In order to help realize this goal and reduce the development time and required experience for the fabrication of SMA actuation systems, several modeling tools have been developed for common actuator types and are discussed herein along with case studies, which highlight the capabilities and limitations of these tools. Due to their ability to sustain high stresses and recover large deformations, SMAs have many potential applications as reliable, lightweight, solid-state actuators. Their advantage over classical actuators can also be further improved when the actuator geometry is modified to fit the specific application. In this paper, three common actuator designs are studied: wires, which are lightweight, low-profile, and easily implemented; springs, which offer actuation strokes upwards of 200 at reduced mechanical loads; and torque tubes, which can provide large actuation forces in small volumes and develop a repeatable zero-load actuation response (known as the two-way shape memory effect). The modeling frameworks, which have been implemented in the design tools, are developed for each of these frequently used SMA actuator types. In order to demonstrate the versatility and flexibility of the presented design tools, as well as validate their modeling framework, several design challenges were completed. These case studies include the design and development of an active hinge for the deployment of a solar array or foldable space structure, an adaptive solar array deployment and positioning system, a passive air temperature controller for regulation flow temperatures inside of a jet engine, and a redesign of the Corvette active hatch, which allows for pressure equalization of the car interior. For each of the presented case studies, a prototype or proof-of-concept was fabricated and the experimental results and lessons learned are discussed. This analysis presents a collection of CASMART collaborative best practices in order to allow readers to utilize the available design tools and understand their modeling principles. These design tools, which are based on engineering models, can provide first-order optimal designs and are a basic and efficient method for either demonstrating design feasibility or refining design parameters. Although the design and integration of an SMA-based actuation system always requires application- and environment-specific engineering considerations, common modeling tools can significantly reduce the investment required for actuation system development and provide valuable engineering insight.

Design tools↗