Search NASA⌕ Search

SEARCH · Search NASA

Results for “Adhesives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2024

Finite Element Modeling of the Phase Change in Thermally-Grown SiO 2 in SiC Systems for Gas Turbines

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO 2 thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb 2 Si 2 O 7 EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO 2 TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation from β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of Particle Spreading Dynamics on Powder Bed Quality in Metal Additive Manufacturing

Powder spreading precedes creation of every new layer in powder bed additive manufacturing (AM). The powder spreading process can lead to powder layer defects such as porosity, poor surface roughness and particle segregation. Therefore, the creation of homogeneous layers is the first task for optimal part printing. Discrete element methods (DEM) powder spreading simulations are typically limited to a single layer and/or small number of particles. Therefore, results from such model configurations may not be generalized to multiple layer processes. In this study, a computationally efficient multi-layer powder spreading DEM simulation model is proposed. The model is calibrated experimentally using static Angle of Repose measurements. The adhesion model parameter, cohesive energy density is related to adhesive surface energy and strain energy release rate parameters. The model results show that interaction between particle and the powder spreading rake leads to noticeable variation in packing density, surface roughness, dynamic angle of repose (AOR), particle size distribution, and particle segregation. Finally, the powder model is experimentally validated using a recoater spreading rig to measure the dynamic AOR at spreading speeds consistent with recoating speeds and layer heights used in AM processes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tribological properties of PDA + PTFE coating in oil-lubricated condition

In this work the tribological properties of 45 ± 2 μm-thick polytetrafluoroethylene (PTFE) and polydopamine (PDA) + PTFE coatings in oil-lubricated conditions were investigated under a normal load of 10 N and a linear reciprocating speed of 0.1 m/s. Both the PTFE and the PDA + PTFE coatings were deposited using an in-house spray-coating method. The PDA + PTFE coating was five times more durable compared to the PTFE coating in oil-lubricated conditions. Both PTFE and PDA + PTFE coatings showed lower COF in oil-lubricated conditions than in dry conditions. The nanomechanical properties measured by PeakForce Quantitative Nanomechanical (PFQNM) characterization method showed an increase in Young’s modulus and adhesion force for the PDA + PTFE coatings compared to the PTFE coatings. Chemical analysis showed that the cross-linking between PDA and PTFE polymer chains occurred during the high-temperature sintering procedure. Finally, the higher adhesion of PDA + PTFE coating to the cast iron substrate and the stronger cohesion due to the cross-linking between PDA and PTFE contributed to the higher durability of the PDA + PTFE composite coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗
DOE OSTI2023

Designing ultrastable Pt/CeO 2 -Al 2 O 3 nanosheet catalysts for three-way catalysts applications

Designing Rh-free, especially Pt-only, three-way catalysts with improved low-temperature activity/stability is highly desirable. Herein, we demonstrate that ultrastable Pt/CeO 2 -Al 2 O 3 nanosheet catalysts can be obtained based on a Sabatier principle of metal-support interaction. Tuning the surface coverage of penta-site rich γ-Al 2 O 3 nanosheets (AlNS, weak adhesion to Pt) by CeO 2 “nano-islands” (strong adhesion to Pt) can lead to the synthesis of Pt/60 wt.%CeO 2 -AlNS that have lower light-off temperatures for CO, hydrocarbons, and NO compared to conventional Pt/CeO 2 and Pt/Al 2 O 3 catalysts by 100–200°C and a similar performance with the state-of-the-art Rh-based catalyst. Further, incorporating CeO 2 on the surface of AlNS can retard the sintering of CeO 2 during harsh redox hydrothermal aging, associate with the strong interaction between CeO 2 “nano-island” and penta-site rich γ-Al 2 O 3 nanosheets. Moreover, the improved activity/stability of Pt/CeO 2 -AlNS catalysts can be attributed to tuning of the Pt detachment and migration from and back to the CeO 2 “nano-islands”, respectively, that keeps Pt as nanoclusters on CeO 2 , the most active species for three-way catalyst applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Scalable thin graphene oxide membranes enabled by polydopamine gutter layer

Two-dimensional (2D) nanosheets have been widely used to fabricate thin-film composite membranes for dye desalination. However, they often need to be thick to mitigate the defects resulting from their random stacking and rough support surface. Herein, bio-adhesive polydopamine (PDA) is used as a gutter layer to prepare graphene oxide (GO)-based membranes by improving the adhesion between the GO and porous support and providing a smooth surface to form thin, highly selective layers. For example, the PDA priming reduces the GO layer thickness by 57 %, from 447 to 190 nm, while achieving similar dye desalination properties. The effect of the dopamine concentration, exposure time, and GO layer thickness on the membrane structure and desalination performance are thoroughly investigated using various techniques, such as scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS), and x-ray diffraction (XRD). The PDA gutter layer is also applied for hollow fiber membranes, achieving water permeance of 79 L m -2 h −1 bar−1 and rejection of ∼99 % for Direct red 80. The membranes were challenged by simulated dye/salt mixtures to elucidate the complicated effect of the compositions on the desalination performance. Furthermore, this study unveils a new avenue to improve separation performance and large-scale manufacturability of 2D material-based membranes.

Dye desalination↗
DOE OSTI2023

First-principles study of interfaces in Al/SiC metal-matrix composite system

In this work, first-principles calculations were performed on the interfaces between Al and SiC, which is a widely used strengthening agent in aluminum metal-matrix-composites (Al/MMC). C-terminated interfaces have much larger work of adhesion than Si-terminated interfaces, indicating that the former has much stronger interfacial bonding. The electron localization function shows that the chemical bonding between Al and C has a strong covalent character, while the bonding between Al and Si is largely metallic. As a result of the vastly different chemical bonding, the work of adhesion for C-terminated interfaces increases with the number of dangling bonds at the interface, while the opposite trend was observed for Si-terminated interfaces. Additionally, the interface energy for Si-terminated interfaces is comparable to that for C-terminated interfaces, suggesting both types of terminations can coexist in the Al/SiC system.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A critical verification of beam and shell models of wind turbine blades

Ever-increasing wind turbine size has challenged predictive capabilities on several fronts. Here, to address part of the blade structural modeling uncertainty, a systematic model fidelity comparison study was conducted on commonly used finite elements. pyNuMAD was utilized to create beam, shell, and solid models of a 100 m long blade undergoing large static deflections. The solid model avoided the use of layered-solid elements by resolving core and facesheet layers. An unprecedented model with 73.7 million elements revealed insights that have never been possible from prior experimental and numerical studies. As compared to the solid element model, the tip deflection from the shell and beam model was found to be about 2% and 4.3% too low, respectively. The twist from the beam model was found to be about 5.6% too high, while the twist from shell model was 24% too low, though improvement was demonstrated with mesh refinement. The beam model adhesive stresses were more accurate than the shell model. Out-of-plane stresses were of great significance near geometric and material discontinuities, and neither the shell nor beam model captured these effects well. Failure predictions from beam, shell, or layered-solid models are unlikely to be reliable at trailing edges, adhesives, ply-drops, spar-cap boundaries.

17 WIND ENERGY↗
DOE OSTI2024

The Effect of Air Separations on Fast Pyrolysis Products for Forest Residue Feedstocks

This study investigates the intricate relationship between biomass preprocessing and pyrolysis product yields, employing the air classification technique for the treatment of loblolly pine residues with varying moisture content. A comprehensive exploration of the physicochemical properties of air-classified loblolly pine informs a sophisticated pyrolysis simulation model. Given the complex and multifaceted nature of biomass pyrolysis, operating across diverse temporal and spatial scales, a pyrolysis kinetics-based CFD–DEM simulation method is employed to predict product yields. Results showed that the elevated moisture content amplifies particle adhesiveness, necessitating augmented air velocities for effective separation, thereby influencing the efficiency of the separation process. While carbon and hydrogen contents exhibit relative stability across diverse moisture contents and blower frequencies, the oxygen content undergoes noticeable changes. For example, the oxygen contents were measured as 29.2 and 38.6 wt% in the light fraction of 30% moisture content sample at blower frequencies of 10 and 20 Hz, respectively. An intriguing finding emerges from pyrolysis simulation, indicating that a lower blower frequency in air classification moderately enhances bio-oil yield and significantly improves its quality, particularly in terms of water content. For instance, the water content in the bio-oil was about 1.5% and 10% in the heavy and light fractions, respectively from 10% moisture sample under 15 Hz blower frequency. In summary, a detailed understanding and strategic manipulation of critical material attributes in biomass through efficient fractionation techniques are imperative for advancing fast pyrolysis as a sustainable avenue for renewable energy and chemical production.

09 BIOMASS FUELS↗
DOE OSTI2022

Anticorrosive epoxy coatings from direct epoxidation of bioethanol fractionated lignin

The development of lignin-based anticorrosive epoxy coatings for steel protection is beneficial for both alleviating the fossil resource depletion and value-added utilization of lignin but remains a challenge due to the inherent heterogeneous structure of lignin. Here, in this study, we selectively extract the low molecular weight (MW) fraction of a crop residue-derived enzymatic hydrolysis lignin (EHL) through a bioethanol fractionation process and prepare epoxy resin by direct epoxidation of the bioethanol fractionated lignin (BFL). The coatings are then fabricated using 20–100 wt% of BFL-based epoxy resin (LEp) as the commercial epoxy resin substitute. The low MW and high p-hydroxyphenyl content of the BFL offer high solubility and good workability for BFL and LEp during epoxidation and coating production, respectively. Lignin-based coatings with 20–40 wt% LEp exhibit good adhesion property (5B) and superior corrosion resistance, compared to the commercial epoxy coating. Although coating with high LEp concentrations (i.e., 60–100 wt%) resulted in decreased adhesion strength, the coating with 100 wt% LEp still displayed corrosion protection performance comparable to that of the commercial epoxy coating. Overall, this study provides a simple and effective approach to converting lignin to epoxy resins for a wide variety of surface coating applications.

09 BIOMASS FUELS↗
DOE OSTI2022

From acetone fractionation to lignin-based phenolic and polyurethane resins

In this paper, acetone fractionation was used to increase the homogeneity of softwood kraft lignin for product development. The acetone soluble and insoluble fractions were analyzed in terms of elemental composition, chemical structure, and thermal properties. The phenolic hydroxyl content of the acetone soluble fraction increased by 24%. The acetone soluble fraction of kraft lignin was used to fully substitute phenol in phenolic resin formulation. The resulting formulated lignin-formaldehyde adhesive showed higher adhesion strength (4.3 MPa) compared to a lab formulated phenol-formaldehyde resin (3.4 MPa) with 100% wood failure after lap shear test. On the other hand, the acetone insoluble lignin fraction, which had 23% higher aliphatic hydroxyl content compared to the starting lignin, was used to entirely replace petroleum-based polyol in polyurethane resin formulation. Then a bio-derived solvent (dihydrolevoglucosenone, Cyrene) was used to dissolve the acetone insoluble lignin fraction to synthesize lignin-based polyurethane resin. Tailoring the structure of kraft lignin through solvent fractionation resulted in two fractions, which were used to replace 100% of two major petrochemicals (phenol and polyol) in the formulations of phenolic and PU resins, that would otherwise be challenging due to the heterogeneity of softwood kraft lignin.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Growth mechanism of glucose-based hydrochar under the effects of acid and temperature regulation

Improving the tailorability of hydrochar synthesis is an effective way to enhance its performance and utilization efficiency. In this study, the growth rate, morphology, and molecular structure of hydrochar were controlled by regulating the pH and temperature of the hydrothermal carbonization process. Growth process analysis indicates that hydrochar has three growth periods: induction, rapid, and stable growth periods. It is mainly controlled by 5-hydroxymethylfurfural (HMF), which is formed by converting glucose and its transformation products. Further, the regulation of acid can significantly shorten the induction period of hydrochar, even under low-temperature conditions (<180 °C), and increase the growth rate of hydrochar. However, the degree of hydrochar adhesion varies: the lower the temperature, the greater the degree of its adhesion. Molecular structural analysis demonstrates that hydrochar mainly consists of furan structural domains and aromatic clusters, and its surface is rich in oxygen-containing functional groups. The degree at which hydrochar was aromatized was improved by increasing the reaction temperature (160–220 °C); whereas the regulation of acid reduced it and increased the content of oxygen-containing functional groups on the hydrochar surface. Based on these results, it is proposed that hydrochar formation has five stages and three growth periods with or without acid regulation.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Leak-tight crack repair for 304L stainless steel using friction surfacing

Here, friction surfacing (FS) was investigated as a method for sealing 50 μm wide thru-cracks in 3-mm-thick 304L stainless steel (304L) plate. Friction surfacing was performed using two sizes of 304L consumable rod, with diameters of 9.52 mm and 12.7 mm, on two substrate conditions (clean and oxidized). Friction surfacing was able to deposit a 600 μm thick coating and repair cracks to a depth of 100 μm - 200 μm below the original surface, when using the 12.7-mm-diameter consumable rod for both substrate conditions. Helium leak rates of 10 -10 atm-cc/s were achieved on crack repairs, designating them as leak-tight by the ANSI N14.5 standard. Optical and scanning electron microscopy were used to investigate the coating microstructure and bond interfaces. In this study, the 12.7-mm-diameter rod performed better with disruption of the oxide layer on the oxidized substrate and providing a more homogenous coating. Mechanical properties of the coated samples were evaluated by performing micro-indentation, tensile, bending, and adhesion testing. Higher hardness in the coatings was observed due to the fine equiaxed grains resulting from dynamic recrystallization. Complete consolidation of plastically deformed material on the substrate and a strong diffusion bond across the interface was observed. This was reflected in tensile and bending properties of the FS coatings being comparable to those of uncoated specimen. No delamination of the FS coating was observed during adhesion testing. The results demonstrate that friction surfacing is a viable option to seal cracks in stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cold Spray Deposition of 304L Stainless Steel to Mitigate Chloride-Induced Stress Corrosion Cracking in Canisters for Used Nuclear Fuel Storage

A feasibility study of the cold spray deposition process of 304L stainless steel on 304L stainless steel substrates as a mitigation method for chloride-induced stress corrosion cracking (CISCC) has been investigated under various substrate conditions. The study is aimed at the application of this technology to mitigate CISCC that may potentially occur in or nearthe fusion welded regions of stainless steel canisters in Dry Cask Storage System (DCSS) for used nuclear fuels. Spherical gas-atomized 304L stainless steel powder, in the size range of 25 µm to 44 µm, was used as a feedstock powder for the cold spray process. The powder was deposited on four types of 304L substrates with various surface conditions: as-polished, oxidized, cold-rolled, plates with prototypical CISCC. The effects of cold spray parameters on quality of cold spray coatings were investigated. Thickness, porosity, and phases in the as-deposited materials were evaluated using scanning electron microscopy (SEM) and X-ray diffraction (XRD), and correlated with microhardness and adhesion strength measured via micro-indentation and ASTM C633 pulling test, respectively. XRD analysis of the coatings was also conducted to examine the effects of cold spray condition on residual stress state in the coating. Detailed cross-sectional examination of coating/substrate interfaces was performed with transmission electron microscopy (TEM) equipped with energy dispersive spectroscopy (EDS). Dense and continuous coatings with good adhesion strength and hardness were produced for the various substrate conditions by adjusting cold spray parameters. The results demonstrate that cold spray stainless steel coating is a viable option to provide a physical barrier against CISCC in fusion weld regions of stainless steel in corrosive chloride salt-bearing environments.

Dry Cask Storage Systems, cold spray, 304L stainle↗
DOE OSTI2021

Evaluation of the anisotropic grain boundaries and surfaces of α -U via molecular dynamics

Alloys based on uranium-zirconium are gaining renewed interest as fuels for the Versatile Test Reactor and a number of microreactor designs. Implementing metallic fuel in reactors creates the need for robust descriptive and predictive fuel performance modeling. Here, the current state of metallic fuel performance modeling relies on empirical equations derived from historical experiments, which may be unreliable when applied outside of their temperature, power, and composition phase space. One area where such data is lacking is the irradiation behavior of alpha -U, specifically tearing and porosity formation at the early stages of irradiation. While grain boundaries likely play a key role in this fuel behavior, relatively little is known about grain boundaries in alpha-U. Thus, we evaluate the grain boundary, surface energy, and work of adhesion of alpha -U utilizing molecular dynamics. Symmetric tilt grain boundaries (STGBs) are analyzed with the tilt plane oriented along each major crystallographic axis, for a total of eighty unique grain boundaries. The effect of temperature, tilt plane, and misorientation angle on interfacial energies are analyzed. The interfacial energies typically increase with temperature and there is significant variance as a function of misorientation angle, irrespective of the tilt plane. At 500 K, the average surface energy (1.23 J/m 2 ) is approximately 1.5 times the grain boundary energy (0.79 J/m 2 ), and the work of adhesion is approximately twice the grain boundary energy (1.68 J/m 2 ). Orientations for the likely formation of twins and likely failure planes are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗