Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Experimental and analytical results of tangential blowing applied to a subsonic V/STOL inlet

Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack.

Burley, R. R.↗
NASA NTRS1982

An analytical procedure for computing smooth transitions between two specified cross sections with applications to blended wing body configuration

An analytical procedure is described for designing smooth transition surfaces for blended wing-body configurations. Starting from two specified cross section shapes, the procedure generates a gradual transition from one cross section shape to the other as an analytic blend of the two shapes. The method utilizes a conformal mapping, with subsequent translation and scaling, to transform the specified and shapes to curves that can be combined more smoothly. A sample calculation is applied to a blended wing-body missile type configuration with a top mounted inlet.

Barger, R. L.↗
NASA NTRS1982

Analytical and simulator study of advanced transport

An analytic methodology, based on the optimal-control pilot model, was demonstrated for assessing longitidunal-axis handling qualities of transport aircraft in final approach. Calibration of the methodology is largely in terms of closed-loop performance requirements, rather than specific vehicle response characteristics, and is based on a combination of published criteria, pilot preferences, physical limitations, and engineering judgment. Six longitudinal-axis approach configurations were studied covering a range of handling qualities problems, including the presence of flexible aircraft modes. The analytical procedure was used to obtain predictions of Cooper-Harper ratings, a solar quadratic performance index, and rms excursions of important system variables.

Levison, W. H.↗
NASA NTRS1982

Analytical and experimental evaluations of Space Shuttle TPS tile vibration response

Analytical studies and laboratory experiments have been performed to evaluate the vibration response of the Space Shuttle Thermal Protection System (TPS) tiles due to the intense rocket generated acoustic noise during lift-off. The TPS tiles are mounted over the exterior of the Space Shuttle Orbiter structure through Strain Isolation Pads (SIP) which protect the tiles from thermal induced shear loads at their interface. The analytical predictions indicate that the response of a typical tile is governed by the structural vibration inputs through the SIP under the tile at frequencies below 250 Hz, and by the direct acoustic excitation over the exterior surface of the tile at frequencies above 250 Hz. An evaluation of the laboratory test data for this same tile, in which conditioned (partial) coherent output spectral analysis procedures were used, leads to exactly the same conclusion. The results demonstrate the power of conditioned spectral analysis procedures in identifying vibration response mechanisms when two or more of the inputs are highly correlated.

Piersol, A. G.↗
NASA NTRS1982

Analytical solution for the drift behavior of Dynamics Explorer-B

The Dynamics Explorer (DE) mission was designed to explore the earth's magnetosphere, ionosphere, and plasmasphere. The DE mission employs two spacecraft, including DE-A and DE-B. The spacecraft were launched from the Western Test Range on Aug. 3, 1981, onboard the same Delta launch vehicle. The two spacecraft were placed in a coplanar polar orbit, with DE-A in a high altitude orbit (perigee = 570 km and apogee = 23174 km) and DE-B in a low altitude orbit (perigee = 309 km and apogee = 1013 km). In the present investigation, an attempt has been made to validate the flight data for DE-B with analytic and simulation results. The external torques acting on the spacecraft are represented in terms of tractable mathematical functions. A piecewise linear model of the superrotation of the upper atmosphere is assumed. The effect of individual torques on the long-term pitch axis motion is investigated using analytic and simulation methods. The results are found to be in very good agreement with the available flight data.

Sellappan, R. G.↗
NASA NTRS1982

Analytical procedures for flutter model development and checkout in preparation for wind tunnel testing of the DAST ARW-1 wing

A study to develop analytical procedures to be used in the checkout and calibration of a flutter wind tunnel model of the DAST ARW-1 wing equipped with a flutter suppression device is reported. The methods used to obtain a realistic simulation of the structural inertial and aerodynamic properties of the wing, the hydro-electro-servo actuator used for flutter suppression, a prediction of the open loop flutter speed at a fixed Mach number (.897), a procedure for checkout and calibration using the method frequency response of a wing mounted accelerometer, and an analytical representation of a reduced state approximation of the overall system are described.

Pines, S.↗
NASA NTRS1983

Analytical and Experimental Evaluation of the Heat Transfer Distribution over the Surfaces of Turbine Vanes

Three airfoil data sets were selected for use in evaluating currently available analytical models for predicting airfoil surface heat transfer distributions in a 2-D flow field. Two additional airfoils, representative of highly loaded, low solidity airfoils currently being designed, were selected for cascade testing at simulated engine conditions. Some 2-D analytical methods were examined and a version of the STAN5 boundary layer code was chosen for modification. The final form of the method utilized a time dependent, transonic inviscid cascade code coupled to a modified version of the STAN5 boundary layer code featuring zero order turbulence modeling. The boundary layer code is structured to accommodate a full spectrum of empirical correlations addressing the coupled influences of pressure gradient, airfoil curvature, and free-stream turbulence on airfoil surface heat transfer distribution and boundary layer transitional behavior. Comparison of pedictions made with the model to the data base indicates a significant improvement in predictive capability.

Hylton, L. D.↗
NASA NTRS1983

On the analytical modeling of the nonlinear vibrations of pretensioned space structures

Pretensioned structures are receiving considerable attention as candidate large space structures. A typical example is a hoop-column antenna. The large number of preloaded members requires efficient analytical methods for concept validation and design. Validation through analyses is especially important since ground testing may be limited due to gravity effects and structural size. The present investigation has the objective to present an examination of the analytical modeling of pretensioned members undergoing nonlinear vibrations. Two approximate nonlinear analysis are developed to model general structural arrangements which include beam-columns and pretensioned cables attached to a common nucleus, such as may occur at a joint of a pretensioned structure. Attention is given to structures undergoing nonlinear steady-state oscillations due to sinusoidal excitation forces. Three analyses, linear, quasi-linear, and nonlinear are conducted and applied to study the response of a relatively simple cable stiffened structure.

Housner, J. M.↗
NASA NTRS1983

Analytical and Numerical Solution for a Solidifying Liquid Alloy Slab

Numerical and analytical solutions are presented for the temperature and concentration distributions during the solidification of a binary liquid alloy slab. The slab is taken to be of a finite depth but infinite in the horizontal direction. The solidification process is started by withdrawing a fixed amount of heat from the lower surface of the slab. The upper surface of the slab is subjected to both radiation and convective conditions. The solution gives the concentration and temperature profiles and the interface position as a function of time. Due to the smallness of the mass diffusion coefficient in the solid, the numerical solution method breaks down whenever the ratio of the diffusivities in the solid and the liquid falls below a certain value. An analytical method is developed which gives accurate solution for any value of the diffusivity ratio.

Antar, B. N.↗
NASA NTRS1984

Analytical Study of Blowing Boundary-Layer Control for Subsonic V/STOL Inlets

The analytical methods used to study blowing boundary-layer control (BLC) for subsonic V/STOL inlets are described. The methods are then shown to give good agreement with experimental results, both with and without blowing BLC. Finally, because of this good agreement, the methods were used to determine analytically the optimum (minimum blowing power required) location and height for a blowing slot within a subsonic V/STOL inlet.

Hwang, D. P.↗
NASA NTRS1984

Analytical and experimental investigation of stator endwall countouring in a small axial-flow turbine

An experimental and analytical investigation was conducted to determine the effect of stator endwall contouring on turbine stage performance. In this investigation three stator configurations were evaluated using a common rotor. The three stator configurations were a cylindrical endwall design and two contoured endwall designs, one having a S-shaped outer wall profile and the other having a conical-shaped outer wall profile. Experimental data were obtained over a range of equivalent speeds, total pressure ratios, and rotor tip clearances for each stator-rotor combination. Detailed analytical loss assessments were conducted to aid in the determination of the contouring effect on turbine performance.

Haas, J. E.↗
NASA NTRS1982

Empirical testing of an analytical model predicting electrical isolation of photovoltaic models

A major design requirement for photovoltaic modules is that the encapsulation system be capable of withstanding large DC potentials without electrical breakdown. Presented is a simple analytical model which can be used to estimate material thickness to meet this requirement for a candidate encapsulation system or to predict the breakdown voltage of an existing module design. A series of electrical tests to verify the model are described in detail. The results of these verification tests confirmed the utility of the analytical model for preliminary design of photovoltaic modules.

Garcia, A., III↗
NASA NTRS1984

System identification of analytical models of damped structures

A procedure is presented for identifying linear nonproportionally damped system. The system damping is assumed to be representable by a real symmetric matrix. Analytical mass, stiffness and damping matrices which constitute an approximate representation of the system are assumed to be available. Given also are an incomplete set of measured natural frequencies, damping ratios and complex mode shapes of the structure, normally obtained from test data. A method is developed to find the smallest changes in the analytical model so that the improved model can exactly predict the measured modal parameters. The present method uses the orthogonality relationship to improve mass and damping matrices and the dynamic equation to find the improved stiffness matrix.

Fuh, J.-S.↗
NASA NTRS1984

An analytic solution for the orbital perturbations of the Venus Radar Mapper due to gravitational harmonics

Hill's variational equations are solved analytically for the orbital perturbations of a spacecraft nominally in an elliptic orbit around a non-spherical body. The rotation of the central planet about its spin-axis is not considered in the analysis. The perturbations are restricted to the planetary gravitational harmonics only. An extremely simple algorithm is derived to transform the spherical harmonic potentials to the orbital coordinate system, and the resulting accelerations are shown to be simply trigonometric functions of the true anomaly. With the principal matrix solution for the differential equations of the adjoint system given in closed form, the orthogonality of the trigonometric functions makes it possible to obtain an analytic solution for the non-homogeneous problem, at intervals of 2 pi in true anomaly. The solution for orbital perturbations can be extended over several revolutions by applying well-known results from Floquet's theory. The technique is demonstrated with results presented on the spacecraft periapsis altitude for the forthcoming Venus Radar Mapper Mission.

Vijayaraghavan, A.↗
NASA NTRS1984

Experimental and analytical investigations into airfoil icing

Methods of analyzing and measuring experimentally the accretion of ice and its effect on airfoil aerodynamic performance are presented. An analytical method for predicting water droplet impingement has been developed and shows the influence of airfoil leading edge radius and thickness on droplet impingement to be significant. Rime ice accretions are predicted including time dependent effects and these shapes compare well to experiment. Scaling water droplet impingement and rime ice accretion is discussed. Predictions of the effect of rime ice on airfoil performance are developed based on empirical and analytical methods. Techniques for measuring and simulating ice accretions for wind tunnel tests compare well to actual iced airfoil aerodynamic data. Data showing the effect of ice on measured airfoil performance using real and simulated ice are presented.

Bragg, M. B.↗
NASA NTRS1985

Analytical modeling of circuit aerodynamics in the new NASA Lewis wind tunnel

Rehabilitation and extention of the capability of the altitude wind tunnel (AWT) was analyzed. The analytical modeling program involves the use of advanced axisymmetric and three dimensional viscous analyses to compute the flow through the various AWT components. Results for the analytical modeling of the high speed leg aerodynamics are presented; these include: an evaluation of the flow quality at the entrance to the test section, an investigation of the effects of test section bleed for different model blockages, and an examination of three dimensional effects in the diffuser due to reentry flow and due to the change in cross sectional shape of the exhaust scoop.

Towne, C. E.↗
NASA NTRS1985

Automated dynamic analytical model improvement for damped structures

A method is described to improve a linear nonproportionally damped analytical model of a structure. The procedure finds the smallest changes in the analytical model such that the improved model matches the measured modal parameters. Features of the method are: (1) ability to properly treat complex valued modal parameters of a damped system; (2) applicability to realistically large structural models; and (3) computationally efficiency without involving eigensolutions and inversion of a large matrix.

Fuh, J. S.↗
NASA NTRS1983

Development of finite analytic method for unsteady three-dimensional Navier-Stokes equation

A finite analytic (FA) numerical method is described for the numerical study of three-dimensional fluid flow problems. The FA method incorporates a local linearization scheme and a classical analytic solution technique to formulate the algebraic representation of unsteady three-dimensional Navier Stokes Equations. The twenty-eight point FA formula thus obtained gives all positive coefficients and desired upwind shift. Cubic cavity flows are then solved by the FA method for Reynolds numbers of 100 and 400. A simple variant of SIMPLER algorithm is used to resolve the pressure-velocity coupling problem. The numerical solutions show that the presence of side walls reduce the strength of the primary vortex when compared with the two-dimensional square cavity flows.

Chen, H.-C.↗