Search NASA⌕ Search

SEARCH · Search NASA

Results for “Base heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Spectroscopic results in helium from the NASA Lewis Bumpy Torus plasma

Spectroscopic measurements have been carried out on the NASA Lewis Bumpy Torus experiment in which a steady state ion heating method based on the modified Penning discharge is applied in a bumpy torus confinement geometry. Electron temperatures in pure helium are measured from the ratio of spectral line intensities. Measured electron temperatures range from 10 to 100 eV. Relative electron densities are also measured over the range of operating conditions. Radial profiles of temperature and relative density are measured in the two basic modes of operation of the device called the low and high pressure modes. The electron temperatures are used to estimate particle confinement times based on a steady state particle balance.

Richardson, R. W.↗
NASA NTRS1977

Temperature distribution in the human body under various conditions of induced hyperthermia

A mathematical model based on heat balance equations was developed for studying temperature distribution in the human body under deep hyperthermia which is often induced in the treatment of malignant tumors. The model yields results which are in satisfactory agreement with experimental data. The distribution of temperature under various conditions of induced hyperthermia, i.e. as a function of water temperature and supply rate, is examined on the basis of temperature distribution curves in various body zones.

Korobko, O. V.↗
NASA NTRS1979

A 15 kWe (nominal) solar thermal-electric power conversion concept definition study: Steam Rankin reciprocator system

A conceptual design of a 3600 rpm reciprocation expander was developed for maximum thermal input power of 80 kW. The conceptual design covered two engine configurations; a single cylinder design for simple cycle operation and a two cylinder design for reheat cycle operation. The reheat expander contains a high pressure cylinder and a low pressure cylinder with steam being reheated to the initial inlet temperature after expansion in the high pressure cylinder. Power generation is accomplished with a three-phase induction motor coupled directly to the expander and connected electrically to the public utility power grid. The expander, generator, water pump and control system weigh 297 kg and are dish mounted. The steam condenser, water tank and accessory pumps are ground based. Maximum heat engine efficiency is 33 percent: maximum power conversion efficiency is 30 percent. Total cost is $3,307 or $138 per kW of maximum output power.

Wingenback, W.↗
NASA NTRS1979

The history of an atmosphere of impact origin

Most of the masses accreting onto the earth and terrestrial planets impacted at sufficiently high velocities to release their volatiles into the atmosphere by impact-heating. However, based on models of planetary growth by accumulation from solid bodies, the time-scale for accretion was sufficiently long that the average surface temperatures could not have risen above 320 K. Using measured reaction rates, the released volatiles should have been re-incorporated into the planet by hydrating the surface minerals and were subsequently buried during accretion. Rapid hydration of impact products precludes the formation of a thick atmosphere as the planet accreted. Thus, only the subsequent differentiation and evolution of the terrestrial planets determined the size and composition of each planet's atmosphere.

Jakosky, B. M.↗
NASA NTRS1980

Ionospheric disturbance overview

A program of research and exploratory development was undertaken to assess the potential impact of Satellite Power System operation on the ionosphere. The program relies on the utilization of ground-based ionospheric heating facilities in order to simulate the ionospheric heating that will come from the Satellite Power System. Thus far, the experimental program directed toward assessing telecommunications impacts has received the most attention, and little impact was observed on VLF, LF, and MF operations.

Rush, C. M.↗
NASA NTRS1981

Rankine engine solar power generation. I - Performance and economic analysis

Results of a computer simulation of the performance of a solar flat plate collector powered electrical generation system are presented. The simulation was configured to include locations in New Mexico, North Dakota, Tennessee, and Massachusetts, and considered a water-based heat-transfer fluid collector system with storage. The collectors also powered a Rankine-cycle boiler filled with a low temperature working fluid. The generator was considered to be run only when excess solar heat and full storage would otherwise require heat purging through the collectors. All power was directed into the utility grid. The solar powered generator unit addition was found to be dependent on site location and collector area, and reduced the effective solar cost with collector areas greater than 400-670 sq m. The sites were economically ranked, best to worst: New Mexico, North Dakota, Massachusetts, and Tennessee.

Gossler, A. A.↗
NASA NTRS1985

Shuttle system ascent aerodynamic and plume heating

The shuttle program provided a challenge to the aerothermodynamicist due to the complexity of the flow field around the vehicle during ascent, since the configuration causes multiple shock interactions between the elements. Wind tunnel tests provided data for the prediction of the ascent design heating environment which involves both plume and aerodynamic heating phenomena. The approach for the heating methodology based on ground test firings and the use of the wind tunnel data to formulate the math models is discussed.

Foster, L. D.↗
NASA NTRS1985

Morphological Stability and Fluid Dynamics of Vapor Crystal Growth

A fundamental understanding of the conditions under which crystals can retain morphological stability, i.e., shape stability of the advancing interface, during growth from vapors was studied. Morphological stability (MS) is a necessary condition for the growth of homogeneous single crystals required for numerous device applications. For crystallization from melts, the MS concepts are well developed and are essentially based on heat and mass transfer conditions about the advancing interface. For crystallization from vapors, the MS requirements are more complex and not well understood. The added complexity arises from the fact that anisotropies in interfacial kinetics are typically stronger in crystallization from vapors than from melts. These pronounced anisotropies root in the distinctly lower atomic roughness of most vapor-solid interfaces.

Rosenberger, F.↗
NASA NTRS1987

Magnetic flares in the protoplanetary nebula and the origin of meteorite chondrules

This study proposes and analyzes a model for the chondrule forming heating events based on magnetohydrodynamic flares in the corona of the protoplanetary nebula which precipitate energy in the form of energetic plasma along magnetic field lines down toward the face of the nebula. It is found that flare energy release rates sufficient to melt the prechondrular matter, leading to the formation of the chondrules, can occur in the tenuous corona of a protostellar disk. Energy release rates sufficient to achieve melting require that the ambient magnetic field strength be in the range that has been inferred separately from independent meteorite remanent magnetization studies.

Levy, E. H.↗
NASA NTRS1986

A siphon mechanism for supplying prominence mass

A siphonlike mechanism for moving mass from the chromosphere to a gravitational well at the top of a magnetic loop to form a prominence is examined. The calculations assume no a priori flow velocity at the loop base. Instead, heating in the loop legs drives the flow. The prominence formation process requires two steps. First, the background heating rate must be reduced to on the order of 1 percent of the initial heating rate required to maintain the coronal loop. This forms an initial condensation at the top of the loop. Second, the heating must take place only in the loop legs in order to produce a pressure differential which drives mass up into the well at the top of the loop. The heating rate in the loop must be increased once the prominence has begun to form, or full prominence densities cannot be achieved in a reasonable time. It is concluded that this heating driven siphonlike mechanism is feasible for producing and maintaining prominences.

Poland, A. I.↗
NASA NTRS1986

Inverted thermal conversion - GaAs, a new alternative material for integrated circuits

A new type of GaAs is developed which exhibits inverted thermal conversion (ITC); i.e., it converts from conducting to semiinsulating upon annealing at about 850 C. In device fabrication, its low resistivity prior to high-temperature processing differentiates ITC GaAs from the standard semiinsulating GaAs. The ITC characteristics are obtained through control of the concentration of the midgap donor EL2 based on heat treatment and crystal-growth modification. Thus EL2 does not exist in the conducting state of ITC GaAs. Conversion to the semiinsulating state during 850 C annealing is caused by the formation of EL2.

Lagowski, J.↗
NASA NTRS1987

Thermal modeling of high rate Li-SOCl2 primary cylindrical cells

Four different heat transfer paths were separately investigated in a spirally-wound D-size cell. Thermal resistances of the relating components along each heat transfer path were calculated, and the total network of thermal resistances was constructed, resulting in the total thermal resistance of approximately 16.4 C/W at Tw = 40 C, and 12.2 C/W at Tw = 100 C. The amount of heat transferred along the radial direction, which is normal to the electrodes, was found to be about 91 percent of the total heat dissipation. Based on the present results obtained at the component level, the present D-size lithium cell may be operated at a C/2 discharge rate under normal discharge conditions below the cut-off voltage of 2.5 V.

Cho, Young I.↗
NASA NTRS1988

Lithospheric evolution of the Northern Arabian Shield: Chemical and isotopic evidence from basalts, xenoliths and granites

The evolution of the upper-mantle and the lower-crust (the conteinental lithosphere), is the area of Israel and Sinai was studied, using the chemical composition and the Nd-Sr isotopic systematics from mantle and crustal nodules, their host basalts, and granites. The magmatism and the metasomatism making the lithosphere are related to uprise of mantle diapirs in the uppermost mantle of the area. These diapirs heated the base of the lithosphere, eroded, and replaced it with new hot material. It caused a domal uplift of the lithosphere (and the crust). The doming resulted in tensional stresses that in turn might develop transport channels for the basalt.

Stein, M.↗
NASA NTRS1987

Thermal properties and effects for Li/BCX (thionyl chloride) cells

New NASA requirements for the screening of lithium cells for space applications involve thermal soaks at elevated temperatures (149 C). The currently qualified Li/BCX cells and three design modifications have been evaluated showing that a design incorporating a shortened electrode stack met this test condition while continuing to satisfy the performance and safety requirements for cells used on NASA manned space vehicles. Information was also developed to show that measured heat capacities for the BCX D size cells correlated well with the heat generated from cells discharged in an insulated environment. Calculated heat capacities based on the amounts and types of materials in a cell were low compared to these values. This information provides the basis for the design of battery packs in the highly insulating environment of outer space.

Takeuchi, E. S.↗
NASA NTRS1987

Advanced gearbox technology

An advanced 13,000 HP, counterrotating (CR) gearbox was designed and successfully tested to provide a technology base for future designs of geared propfan propulsion systems for both commercial and military aircraft. The advanced technology CR gearbox was designed for high efficiency, low weight, long life, and improved maintainability. The differential planetary CR gearbox features double helical gears, double row cylindrical roller bearings integral with planet gears, tapered roller prop support bearings, and a flexible ring gear and diaphragm to provide load sharing. A new Allison propfan back-to-back gearbox test facility was constructed. Extensive rotating and stationary instrumentation was used to measure temperature, strain, vibration, deflection and efficiency under representative flight operating conditions. The tests verified smooth, efficient gearbox operation. The highly-instrumented advanced CR gearbox was successfully tested to design speed and power (13,000 HP), and to a 115 percent overspeed condition. Measured CR gearbox efficiency was 99.3 percent at the design point based on heat loss to the oil. Tests demonstrated low vibration characteristics of double helical gearing, proper gear tooth load sharing, low stress levels, and the high load capacity of the prop tapered roller bearings. Applied external prop loads did not significantly affect gearbox temperature, vibration, or stress levels. Gearbox hardware was in excellent condition after the tests with no indication of distress.

Anderson, N. E.↗
NASA NTRS1991

Cooling of in-situ propellant rocket engines for Mars mission

One propulsion option of a Mars ascent/descent vehicle is multiple high-pressure, pump-fed rocket engines using in-situ propellants, which have been derived from substances available on the Martian surface. The chosen in-situ propellant combination for this analysis is carbon monoxide as the fuel and oxygen as the oxidizer. Both could be extracted from carbon dioxide, which makes up 96 percent of the Martian atmosphere. A pump-fed rocket engine allows for higher chamber pressure than a pressure-fed engine, which in turn results in higher thrust and in higher heat flux in the combustion chamber. The heat flowing through the wall cannot be sufficiently dissipated by radiation cooling and, therefore, a regenerative coolant may be necessary to avoid melting the rocket engine. The two possible fluids for this coolant scheme, carbon monoxide and oxygen, are compared analytically. To determine their heat transfer capability, they are evaluated based upon their heat transfer and fluid flow characteristics.

Armstrong, Elizabeth S.↗
NASA NTRS1991

Models of recurrent strike-slip earthquake cycles and the state of crustal stress

Numerical models of the strike-slip earthquake cycle, assuming a viscoelastic asthenosphere coupling model, are examined. The time-dependent simulations incorporate a stress-driven fault, which leads to tectonic stress fields and earthquake recurrence histories that are mutually consistent. Single-fault simulations with constant far-field plate motion lead to a nearly periodic earthquake cycle and a distinctive spatial distribution of crustal shear stress. The predicted stress distribution includes a local minimum in stress at depths less than typical seismogenic depths. The width of this stress 'trough' depends on the magnitude of crustal stress relative to asthenospheric drag stresses. The models further predict a local near-fault stress maximum at greater depths, sustained by the cyclic transfer of strain from the elastic crust to the ductile asthenosphere. Models incorporating both low-stress and high-stress fault strength assumptions are examined, under Newtonian and non-Newtonian rheology assumptions. Model results suggest a preference for low-stress (a shear stress level of about 10 MPa) fault models, in agreement with previous estimates based on heat flow measurements and other stress indicators.

Lyzenga, Gregory A.↗