Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capacity degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Cost-Optimized Cold Climate Heat Pump Development and Field Test

Cold climate heat pumps (CCHPs) expand the heat pump market to climates where heating demand is dominant. They can achieve more than 70% energy savings compared with electric resistance heating and operate at lower cost than using tank-stored propane to fuel a furnace. A high-efficiency heat pump with a heating seasonal performance factor (HSPF)—as defined by the Air-Conditioning, Heating, and Refrigeration Institute (AHRI 2008)—greater than 10.0 would be more efficient than gas heating in terms of source energy. However, developing a cost-effective CCHP involves some challenges. A typical single-speed, air-source heat pump (ASHP) with an HSPF of 7.7 Btu/Wh does not work well under cold outdoor temperature conditions typical of cold climate locations for four major reasons: 1. Discharge temperature is too high—The low suction pressure and high compression pressure ratio at low ambient temperatures causes high compressor discharge temperatures in excess of the maximum limit for many of the compressors on the market. Furthermore, system charge of a heat pump is usually optimized in the cooling mode, which leads to overcharge conditions in the heating mode, further increasing the discharge temperature. 2. Heating capacity is insufficient if sized to meet the building design cooling load— Heating capacity of a single-speed heat pump decreases with ambient temperature. The heating capacity at -13°F (-25°C) typically decreases to 20%–40% of the rated heating capacity at 47°F (8.3°C) (~equivalent to the rated cooling capacity at 95°F [35°C]). Therefore, a single-speed heat pump, typically sized to match the building design cooling load, cannot provide adequate heating capacity to match the building heating load at low ambient temperatures. The capacity deficit is filled by inefficient resistance heat, thus lowering the system efficiency and significantly increasing power demand. 3. Cyclic loss is significant if sized to meet the building design heating load—If a single-speed heat pump is sized to meet the heating load, it will be significantly oversized relative to the cooling load in many cold climates. This will cause excessive on/off cyclic loss during the cooling and heating operations at moderately low ambient temperatures. Thus, capacity modulation capability (e.g., using a variable-speed or multi-stage compressor) is necessary for a CCHP, which uses its full capacity to meet the peak heating load and partial capacity to meet the cooling and part-load heating loads. 4. Coefficient of performance (COP) is low—Heating COP degrades significantly at low ambient temperatures owing to the large temperature difference between the heat source and sink. A target CCHP should be sized to meet the building design heating load while minimizing the cyclic loss for the cooling and heating operations at moderate ambient temperatures.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Degradation and Modeling of Large-Format Commercial Lithium-Ion Cells as a Function of Chemistry, Design, and Aging Conditions

Demand for large-format (>10 Ah) lithium-ion batteries has increased substantially in recent years, due to the growth of both electric vehicle and stationary energy storage markets. The economics of these applications is sensitive to the lifetime of the batteries, and end-of-life can either be due to energy or power limitations. Despite this, there is little information from cell manufacturers on the sensitivity of cell degradation to environmental conditions or battery use. This work reports accelerated aging test data from four commercial large-format lithium-ion batteries from three manufacturers, with varying design (thickness, casings, ...), chemistry (lithium-iron-phosphate (LFP) or lithium-nickel-manganese-cobalt-oxide positive electrodes (NMC), with graphite (Gr) negative electrodes), and capacity (50 to 250 Amp hours). The tested LFP|Gr cell is found to be relatively insensitive to cycling conditions like temperature or voltage window, while NMC|Gr cells have varying sensitivity. Degradation trends are further investigated by training predictive models: simple polynomial trend lines, a semi-empirical reduced-order model, and an empirical reduced-order model identified using machine-learning based on symbolic regression. Calendar and cycle life are simulated over a variety of conditions to directly compare the various batteries. Cell size and thickness are found to substantially impact sensitivity to temperature during cycle aging, while electrode chemistry impacts depth-of-discharge sensitivity. Real-world battery lifetime is evaluated by simulating residential energy storage and commercial frequency containment reserve systems in several U.S. climate regions. Predicted lifetime across cell types varies from 7 years to 20+ years, though all cells are predicted to have at least 10 year life in certain conditions.

battery lifetime↗
DOE OSTI2021

Effects of short-term over-discharge cycling on the performance of commercial 21,700 lithium-ion cells and the identification of degradation modes

In this paper, short-term over-discharge cycling was performed on commercially available 21,700 lithium-ion cells to investigate its effects on cell performance; the degradation modes were also identified and analyzed in detail using both in-situ and ex-situ methods. Results show that observable capacity loss occurs when the cell is over-discharged to 112.5% depth of discharge. Moreover, the negative impact of the depth of discharge on cell performance (or cell aging) is more serious than the number of cycles, and continuous over-discharge cycling will accumulate such impact. The loss of Li inventory related to the decomposition and reformation of solid electrolyte interphase film is an important cause of the irreversible capacity loss/degradation of Li-ion cells during over-discharge cycling testing. Furthermore, the dissolution of copper current collector can greatly reduce the mechanical stability of the anode, and further, the deposition of Cu, the exfoliation and the cracking of active material particles can influence the transfer of ions and lead to the loss of Li inventory and the loss of active material within Li-ion cells. Additionally, when the depth of discharge exceeds 108.3%, deposition of Cu is observed on the ceramic-covered side of separators.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrothermal mineralization of per- and polyfluoroalkyl substances for soil remediation

Abstract Per- and polyfluoroalkyl substances (PFAS) are persistent and bioaccumulative pollutants that can easily accumulate in soil, posing a threat to environment and human health. Current PFAS degradation processes often suffer from low efficiency, high energy and water consumption, or lack of generality. Here, we develop a rapid electrothermal mineralization (REM) process to remediate PFAS-contaminated soil. With environmentally compatible biochar as the conductive additive, the soil temperature increases to >1000 °C within seconds by current pulse input, converting PFAS to calcium fluoride with inherent calcium compounds in soil. This process is applicable for remediating various PFAS contaminants in soil, with high removal efficiencies ( >99%) and mineralization ratios ( >90%). While retaining soil particle size, composition, water infiltration rate, and cation exchange capacity, REM facilitates an increase of exchangeable nutrient supply and arthropod survival in soil, rendering it superior to the time-consuming calcination approach that severely degrades soil properties. REM is scaled up to remediate soil at two kilograms per batch and promising for large-scale, on-site soil remediation. Life-cycle assessment and techno-economic analysis demonstrate REM as an environmentally friendly and economic process, with a significant reduction of energy consumption, greenhouse gas emission, water consumption, and operation cost, when compared to existing soil remediation practices.

Science & Technology - Other Topics↗
DOE OSTI2025

Solid Amine CO2 Adsorbent Degradation: Insights from Experiments and Atomistic Simulations

Direct air capture (DAC) has received significant attention this decade as a viable solution to limit global warming, although large-scale deployment is currently not economically feasible. To reach the ambitious cost target set by the U.S. of $100/ton CO2 captured and stored, significant improvements must be made to sorbent lifetime and capacity. Aminosilanes grafted onto silica supports are promising candidates for deployment in DAC systems due to their relatively high oxidative stability and low regeneration temperature. Despite myriad advancements in the field, there still exists a fundamental knowledge gap relating sorbent structure to performance. In this work, we grafted various aminosilanes onto the highly porous silica SBA-15 and characterized both oxidative stability and CO2 capacity. Material properties systematically investigated included amine moiety (primary vs. secondary), silane group structure, number of linkages to the silica support, and co-addition of impregnated amines (e.g., PEI), among others. A fixed bed system was used to execute accelerated degradation studies in the presence of humidity and varying temperatures to simulate realistic operating conditions. Atomistic simulations were combined with the experimental results to gain mechanistic insight, ultimately informing the design of next-generation materials

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

The Influence of Mesoscale Particle Structure on the Electrode Degradation and Resultant Electrochemistry of Lithium Ion Cells With Nickel Rich Lithium Nickel Manganese Cobalt Oxide Positive Electrodes

Nickel-rich lithium nickel manganese cobalt oxide, NMC (LiNi x Mn y Co z O 2 ), materials are desirable positive electrodes in lithium ion batteries, providing high capacity and energy density. The mesoscale structure of NMC materials is commonly a polycrystalline aggregate, providing opportunity for short lithium ion transport distance of the small primary particles, yet facile material handling due to the larger secondary particles. On (de)lithiation the NMC unit cell changes volume, where the anisotropic strain can result in secondary particle fracture. This secondary particle fracture process during cycling has been associated with several degradation modes of NMC materials in LIBs. In this work, a milling process was determined whereby the secondary particles could be pre-fractured with retention of the parent primary particle crystallographic structure, crystallite size, and morphology, providing the ability to unambiguously determine the influence of NMC secondary particle size and mesostructure on resultant functional behavior. The bulk and interfacial properties and electrochemistry of as-received commercially obtained polycrystal NMC811 (LiNi 0.8 Mn 0.1 Co 0.1 O 2 , PC NMC) and its milled MPC NMC counterpart were compared. The smaller secondary particle size, higher surface area MPC NMC was found to result in 1) greater cathode tortuosity, 2) reduced surface Ni on the cycled MPC cathodes consistent with surface reconstruction, and 3) increased Ni deposition on the anodes from cathode-anode crosstalk. These factors manifested in unfavorable electrochemical behavior of MPC with lower functional capacity at both 1C and C/10 rates and higher impedance over extended moderate voltage (dis)charge cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Long-term thermal aging of parylene conformal coating under high humidity and its effects on tin whisker mitigation

Usage of pure tin (Sn) or Sn-rich alloy in electronics industry is growing, which makes them more susceptible to the spontaneous growth of tin whiskers. The risk of having these whiskers can be dramatically mitigated by applying a conformal coating provided that it not only possesses excellent mechanical and adhesion properties but also maintains these properties throughout their service. Parylene C is commonly used as a conformal coating because of its favorable mechanical and physical properties, as well as superior conformal coverage. The purpose of this paper is to investigate the degradation of parylene C coating during the thermal aging in high humidity environment (85°C/85% relative humidity for up to 5000hrs) and its effect on the tin whisker mitigation capacity. It was observed that during aging at high temperature and high humidity (HTHH) environment, the oxidation occurs at early times, followed by bond scission, resulting in the loss of strength of the coating. Thinner parylene coating (12.5-μm-thick) had better coating adhesion on the silane-treated tin surface, so provided the better protection for tin whisker penetration than the thicker counterpart (25-μm-thick). After 2500hrs of aging, due to the degradation of the silane agent at the tin/parylene interface, the adhesion of the parylene coating was significantly weakened on the tin surface, which resulted in extensive corrosion of the tin solderpads. The loss of adhesion of the coating, along with the corrosion of the tin surface facilitated the tin whisker nucleation at the interface while the loss of mechanical strength and the brittleness made the coating easily penetrated by the growing whiskers. Tin whiskers with a smaller diameter were buckled and grew along the delaminated region while those with a larger diameter penetrated and continued to grow through the coating. Hence, the effectiveness of the parylene coatings on tin whisker mitigation is significantly reduced under long exposure to such high temperature and high humidity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solvent-mediated oxide hydrogenation in layered cathodes

Self-discharge and chemically induced mechanical effects degrade calendar and cycle life in intercalation-based electrochromic and electrochemical energy storage devices. In rechargeable lithium-ion batteries, self-discharge in cathodes causes voltage and capacity loss over time. The prevailing self-discharge model centers on the diffusion of lithium ions from the electrolyte into the cathode. Here, we demonstrate an alternative pathway, where hydrogenation of layered transition metal oxide cathodes induces self-discharge through hydrogen transfer from carbonate solvents to delithiated oxides. In self-discharged cathodes, we further observe opposing proton and lithium ion concentration gradients, which contribute to chemical and structural heterogeneities within delithiated cathodes, accelerating degradation. Hydrogenation occurring in delithiated cathodes may affect the chemo-mechanical coupling of layered cathodes as well as the calendar life of lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Analysis of degradation in residential battery energy storage systems for rate-based use-cases

This article examines the impact of residential battery energy storage (BES) systems' operational modes on the life (i.e. usable energy capacity) of the battery under several climatic conditions and battery chemistries. The sharp increase in residential BES installations has been a result of decreasing costs of batteries, increase in rate structures motivated applications such as solar self-consumption and time-of-use energy management, and customers purchasing these systems for backup power. While these different modes of operations provide a combination of increased bill savings, reliability of supply, and energy sustainability to the customer, their operational characteristics vary significantly between use-cases. Functional life of BES systems is known to be strongly dependent on their operating conditions. In this article, we analyze the operation of residential BES systems under different rate-based use-cases, for different battery chemistries and cell designs, and under different environmental conditions. This is conducted by simulating the control of BES operations using rate-based cycling algorithms and analyzing the prognosis of multiple battery lifetime models that consider complex nonlinear dependencies of operational stress factors such as state-of-charge, depth-of-discharge, and temperature on degradation. Significant variations in battery life are observed owing to the differences in characteristics of the uses-cases coupled with environmental conditions and battery chemistries. Such differences lead to the conclusion that choice of residential BES technologies and chemistries should account for their intended use-cases.

25 ENERGY STORAGE↗
DOE OSTI2025

Cost-optimized energy storage operation for a grid-connected solar PV system at community and individual scales

This study provides a comparative analysis of grid-connected PV-integrated battery storage at individual and community scales. The paper addresses the challenge of managing energy demand-generation mismatch by using a battery energy storage optimization algorithm, which minimizes operational costs while accounting for battery degradation. Also, this work introduces a broader evaluation basis that includes seasonal variability, grid exchange smoothness, and scalability across different battery capacities. Results show that community-scale storage more effectively dampens grid exchange power fluctuations and reduces system costs, particularly with moderate price differences between electricity buying and selling prices and low battery capacities. The paper also analyzes the impacts of static control versus cost-optimized battery system management. Here, it is shown that the gap in system costs between the cost-optimized and static control scenarios widens as the price difference increases.

25 ENERGY STORAGE↗
DOE OSTI2025

Chemo-Mechanical Behavior and Stability of High-Loading Cathodes in Solid-State Batteries

Solid-state batteries can offer higher energy density and improved safety compared to lithium ion batteries, which use flammable liquid electrolytes. Increasing the ratio of cathode active materials in composite cathodes enhances the energy density and reduces manufacturing costs. Changes in the ratio of cathode active materials alter the microstructure and chemo-mechanical response of a cathode during operation. Understanding the relationship between composition, microstructure, and chemo-mechanical interactions is critical for optimizing solid-state cathodes. Here, in this study, we engineered composite cathodes with varying ratios of LiNi 0.8 Co 0.1 Mn 0.1 O 2 and Li 6 PS 5 Cl to systematically investigate the role of microstructural evolution in long-term chemo-mechanical transformations. Chemo-mechanical stresses resulting from the volume changes of the cathode active materials led to degradation mechanisms, such as fracture and interfacial delamination. Active material fracture and delamination led to underutilization of active material and significant capacity decay during cycling. Coatings that suppress active material-active material interactions during cycling may aid in suppressing the generation of local stress hotspots.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Topotaxially grown composite cathodes for cobalt-free high-energy long-life Li-ion batteries

The vehicle industry’s increasing demand for electrification necessitates the removal of expensive and rare cobalt from current high-energy batteries. However, eliminating cobalt poses challenges due to its vital role in maintaining the layered structural ordering and cycling stability of commonly used Li(NiMnCo)O 2 cathodes. As an alternative to conventional layered oxide designs, we report a lithium nickelate cathode with a composite structure comprising major stoichiometric layered and minor rocksalt phases within the same oxygen lattice. This material outperforms conventional designs by maintaining stable battery operation at voltages up to 4.8 V vs. Li|Li + , with 88% capacity retention after 1000 cycles at 2C. The topotaxial-growth-enabled interlock between the two components mitigates chemo-mechanical degradation, offering a promising pathway to cobalt-free cathodes. Additionally, we reveal a miscibility gap in the Li-Ni-O system that enables kinetic adjustment of composition and structure during sintering, thereby tuning the functionality of high-energy cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

An in situ formed inorganic conductive network enables high stability and rate capability of single-crystalline nickel-rich cathodes

Single-crystalline Ni-rich cathodes are promising for the next generation of high-energy-density Li-ion batteries due to their better capacity retention than their polycrystalline counterparts. However, there is still much room for improving the electrochemical performances when considering their surface degradation and severe kinetic hindrance during cycling. Herein, we report a strategy to construct an in situ formed robust Li-conductive Li 3 PO 4 layer on the surface of cathode particles. This Li-conductive layer significantly increases the Li-ion diffusion coefficients and suppresses detrimental surface phase transformation. In situ XRD reveals that the improved kinetics alleviate the local stress at high voltage. The as-prepared single-crystalline LiNi 0.83 Co 0.12 Mn 0.05 O 2 delivers good durability (96.8% after 100 cycles at 1C) and excellent rate capability (177.08 mA h g -1 at 5C). Here, this work provides a facile and efficient strategy to improve the cycling performance and boost the rate capability of single-crystalline Ni-rich cathodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Sorbent Based Post-Combustion CO 2 Slipstream Testing

TDA Research, Inc. has developed a low-cost sorbent (alkalized alumina) based technology for post-combustion CO 2 capture. The sorbent runs in an isothermal process for adsorption and regeneration. Neither temperature swing nor pressure swing is needed. TDA designed a system which operated 10 fixed beds to simulate a moving bed process. The flow pattern was optimized to minimize the steam usage for regeneration. An excellent sorbent (Batch 1) was also developed with collaboration with our partner. The sorbent degraded after long term operation. We developed a reprocessing procedure, which can be conducted in situ, to restore the sorbent capture capacity as the fresh sorbent after running for about 1250 hours. The reprocessing extended the sorbent longevity significantly. TDA designed a pilot unit (40’ x 32’ x 11.5’), processing flue gas equivalent to 0.5 MW of power generation. It had 10 beds and each bed could hold 1.75 m 3 of sorbent. We worked with Springs Fabrication, Inc. to complete the construction of the pilot unit. It was then shipped and installed at NCCC. The pilot unit was kept running in 24-hour mode when the flue gas and steam were available. It could run automatically without operator on site. Parametric and long-term (2 months) tests were carried out successfully. The results showed that TDA’s process can achieve 90% capture and 95% CO 2 purity for both coal and NG flue gases. For coal flue gas, the system reached performance target when processing up to 0.62 MW flue gas, 24% higher than the design capacity. Thus, capital cost could be saved on the reactors and sorbent. The strip air flow was designed to be 0.25 of that of the flue gas. The test data showed the strip/flue ratio can be reduced to as little as 0.18, which saves the power consumption for the strip air blower. The pressure drop was found to be lower than what the empirical equation calculated. The sorbent still had 91.7% of original capacity after 3-month test. With the data from the pilot test, we updated the TEA. For a 550-MW e supercritical coal fired power plant with CO 2 capture, the capture cost for TDA’s process is $34.9/tonne CO 2 captured, which meets DOE’s goal of $40/tonne and is 17.1% less than the DOE baseline Case 12. Therefore, TDA’s process has a good potential for commercialization.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Physical Interpretation of Early Battery Life Prediction Models

Early battery life prediction models are most useful for R&D if they help us understand the early changes in battery electrochemical response that correspond with long-term degradation and failure. Linear regression models such as Fused lasso and Partial Least Squares can fit coefficients directly to high-dimensional electrochemical data like capacity-voltage and ΔV–state-of-charge, i.e., Q(V) and ΔV(SOC) curves, learning coefficients that can be physically interpreted. We leverage the ISU-ILCC battery aging data set to learn high-dimensional coefficients for early battery life prediction from traditional slow-rate capacity check data, demonstrating learning on Q(V), d Q· d V −1 , and ΔV(SOC) curves. A thorough study on the dependence of coefficient values on train/test size and data preprocessing methods is made, demonstrating the reliability of high-dimensional regression approaches unless very small amounts of data are used for model training. For this data set, coefficients from Q(V) and d Q· d V −1 models highlight changes in electrode stoichiometry due to lithium loss, while ΔV(SOC) coefficients highlight changes in positive electrode diffusivity due to particle cracking as well as electrode stoichiometry shifts. By directly interpreting the coefficients of a regression model, we make physical insights into battery degradation mechanisms without requiring the assumptions of traditional battery data analysis methods.

25 ENERGY STORAGE↗
DOE OSTI2022

Modeling Chemo-Mechanics with Electrolyte Infiltration to Quantify Degradation of Cathode Particles

One of the main goals in modeling lithium-ion batteries is to improve/predict longevity and resilience of new chemistries. To that end, this talk investigates the formation of stress-induced fracture within polycrystalline cathode particles and the impact on capacity loss. Physically based cathode aging dynamics is simulated in a 3D, continuum-level chemo-mechanical model. The model captures anisotropic Li diffusion within a single polycrystalline particle comprised of hundreds to thousands of randomly oriented grains. A recent addition to this model includes electrolyte infiltration, which occurs when the electrolyte seeps into surface cracks within the particle. The model predicts that particle fracture is primarily due to non-ideal grain interactions with slight dependence on high-rate charge demands. Essentially, when neighboring grains are misaligned, they expand a different rates relative to one another leading to high stresses and ultimately the formation of intraparticle cracks. The model predicts that small particles with large grains develop significantly less damage than larger particles with small grains. Finally, the model predicts most of the chemo-mechanical damage accumulates in the first charge after formation. This chemo-mechanical "damage saturation" effect indicates that initial particle fracture occurs within the first few cycles, while long-term cathode degradation is not solely chemo-mechanically induced. The principle contribution of this research is the use of an anisotropic chemo-mechanical model to test how particle geometry affect capacity fade, which predicts that particle size has a stronger effect on capacity fade than grain size and ultimately that small particles with large grains have the least capacity fade.

cathode↗
DOE OSTI2025

Mechanically Robust Bismuth-Embedded Carbon Microspheres for Ultrafast Charging and Ultrastable Sodium-Ion Batteries

Advancements in the development of fast-charging and long-lasting microstructured alloying anodes with high volumetric capacities are essential for enhancing the operational efficiency of sodium-ion batteries (SIBs). These anodes, however, face challenges such as declined cyclability and rate capability, primarily due to mechanical degradation reduced by significant volumetric changes (over 252%) and slow kinetics of sodium-ion storage. Herein, we introduce a novel anode design featuring densely packed bismuth (Bi) embedded within highly conductive carbon microspheres to overcome the aforementioned challenges. Remarkably, the high loading Bi anode within carbon microspheres with a high tap density of 2.59 g cm -3 possesses significant mechanical strength exceeding 590 MPa and limits volume swelling of only 10.9% post-sodiation. This anode demonstrates a high volumetric capacity (908.3 mAh cm -3 ), ultrafast chargeability (200 A g -1 , full charge/discharge in just 5.5 s), and outstanding cyclability over 12,000 cycles and maintains exceptional cycling stability even at -30 °C. The full cell paired with a Na 3 V 2 (PO 4 ) 3 cathode retains over 80% capacity after 600 cycles at 36 C, demonstrating a remarkable rate capability of 126 C (full charge/discharge in 28.6 s). Our comprehensive experimental evaluations and chemo-mechanical simulations shed light on the mechanisms underpinning the anode's superior performance. In conclusion, this development marks a significant advancement in the design of durable and fast-charging anodes for high-performance SIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Hydrothermal synthesis of Co-free NMA cathodes for high performance Li-ion batteries

Scalable and sustainable production of high voltage cathodes is required to meet the increasing demands for Li-ion batteries. Additionally, the anticipated scarcity of critical materials like cobalt necessitates demonstration of Co-free alternatives that can match the performance metrics of conventional cathodes. Herein, a hydrothermal synthesis route for production of a new class of high-capacity, cobalt-free cathode material, LiNi 0.9 Mn 0.05 Al 0.05 O 2 (NMA9055) for next-generation Li-ion batteries is reported. In this work, the synthesized cathode material shows high crystallinity and purity with monodispersed spherical morphology. Extensive electrochemical, structural, and post-mortem characterization of this novel NMA material is carried out. NMA-Li half cells show an initial discharge capacity of 200 mAh/g with a 96% capacity retention over 100 cycles when cycled between 3.0 and 4.4 V. On the other hand, NMA full cells with Li 4 Ti 5 O 12 (LTO) electrodes as the anode, show an initial discharge capacity of 186 mAh/g with 81% capacity retention over 200 cycles. Post-mortem structural and morphological characterization show that the NMA morphology and crystal structure do not degrade significantly over 200 charge/discharge cycles. This new class of cobalt free cathode material containing nickel, manganese and aluminum synthesized by an ammonia-free synthesis route is expected to provide a facile solution towards sustainable cathode production.

25 ENERGY STORAGE↗