Results for “Configurations” — Page 21

NASA NTRS2015

Numerical Experiments of Counterflowiing Jet Effects on Supersonic Slender-Body Configurations

Previous studies have demonstrated that the use of counterflowing jets can greatly reduce the drag and heat loads on blunt-body geometries, especially when the long penetration mode jet condition can be established. Previously, the authors had done some preliminary numerical studies to determine the ability to establish long penetration mode jets on a typical Mach 1.6 slender configuration, and study its impact on the boom signature. The results indicated that a jet with a longer penetration length was required to achieve any impact on the boom signature of a typical Mach 1.6 slender configuration. This paper focuses on an in-depth parametric study, done using the space-time conservation element solution element Navier-Stokes flow solver, for investigating the effect of various counterflowing jet conditions/configurations on two supersonic slender-body models (cone-cylinder and quartic body of revolution). The study is aimed at gaining a better understanding of the relationship between the shock penetration length and reduction of drag and boom signature for these two supersonic slender-body configurations. Different jet flow rates, Mach numbers, nozzle jet exit diameters and jet-to-base diameter ratios were examined. The results show the characteristics of a short-to-long-to-short penetration-mode pattern with the increase of jet mass flow rates, observed across various counterflowing jet nozzle configurations. Though the optimal shock penetration length for potential boom-signature mitigation is tied to the long penetration mode, it often results in a very unsteady flow and leads to large oscillations of surface pressure and drag. Furthermore, depending on the geometry of the slender body, longer jet penetration did not always result in maximum drag reduction. For the quartic geometry, the maximum drag reduction corresponds well to the longest shock penetration length, while this was not the case for the cone-cylinder-as the geometry was already optimized for drag. Numerical results and assessments obtained from this parametric study along with the recommendation for future implementation of counterflowing jets as a means for drag and noise reduction are detailed in this paper.

Venkatachari, Balaji Shankar↗

NASA NTRS2016

CFD Predictions for Transonic Performance of the ERA Hybrid Wing-Body Configuration

A computational study was performed for a Hybrid Wing Body configuration that was focused at transonic cruise performance conditions. In the absence of experimental data, two fully independent computational fluid dynamics analyses were conducted to add confidence to the estimated transonic performance predictions. The primary analysis was performed by Boeing with the structured overset-mesh code OVERFLOW. The secondary analysis was performed by NASA Langley Research Center with the unstructured-mesh code USM3D. Both analyses were performed at full-scale flight conditions and included three configurations customary to drag buildup and interference analysis: a powered complete configuration, the configuration with the nacelle/pylon removed, and the powered nacelle in isolation. The results in this paper are focused primarily on transonic performance up to cruise and through drag rise. Comparisons between the CFD results were very good despite some minor geometric differences in the two analyses.

Deere, Karen A.↗

NASA NTRS2016

International Space Station Configuration Analysis and Integration

Ambitious engineering projects, such as NASA's International Space Station (ISS), require dependable modeling, analysis, visualization, and robotics to ensure that complex mission strategies are carried out cost effectively, sustainably, and safely. Learn how Booz Allen Hamilton's Modeling, Analysis, Visualization, and Robotics Integration Center (MAVRIC) team performs engineering analysis of the ISS Configuration based primarily on the use of 3D CAD models. To support mission planning and execution, the team tracks the configuration of ISS and maintains configuration requirements to ensure operational goals are met. The MAVRIC team performs multi-disciplinary integration and trade studies to ensure future configurations meet stakeholder needs.

Anchondo, Rebekah↗

NASA NTRS2017

Flow Structure Comparison for Two 7-Point LDI Configurations

This paper presents a comparison primarily of the cold flow 2-D velocity profiles; and describes flame tube combusting flow operability for a 7-point Lean Direct Injector (LDI). This circular LDI array consists of a center element surrounded by six outer elements spaced 60 degrees apart; the spacing between all adjacent elements is the same. Each element consists of a simplex atomizer that injects at the throat of a converging-diverging venturi, and an axial swirler upstream of the venturi throat to generate swirl. The two configurations were: 1) one which consists of all 60 deg co-swirling axial air swirlers, and; 2) one configuration which uses a 60 deg swirler in the center, surrounded by counter-swirling 45 deg swirlers. Testing was done at 5- bar and at an inlet temperature of 700K. Two air reference velocities were considered in the cold flow measurements. The 2D velocity profiles were determined using particle image velocimetry. Results indicate the configuration using all 60 deg swirlers generates a field that moderates to a more uniform distribution at a shorter distance downstream and is more easily operable than the second configuration, which produces recirculation regions at the edges of the outer 45 deg swirlers, and results in a more stratified velocity field at any given axial location.

velocity↗

NASA NTRS2017

A Sweeping Jet Application on a High Reynolds Number Semispan Supercritical Wing Configuration

The FAST-MAC circulation control model was modified to test an array of unsteady sweeping-jet actuators at realistic flight Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center. Two types of sweeping jet actuators were fabricated using rapid prototype techniques, and directed over a 15% chord simple-hinged flap. The model was configured for low-speed high-lift testing with flap deflections of 30 deg and 60 deg, and a transonic cruise configuration having a 0 deg flap deflection. For the 30 deg flap high-lift configuration, the sweeping jets achieved comparable lift performance in the separation control regime, while reducing the mass flow by 54% as compared to steady blowing. The sweeping jets however were not effective for the 60 deg flap. For the transonic cruise configuration, the sweeping jets reduced the drag by 3.3% at an off-design condition. The drag reduction for the design lift coefficient for the sweeping jets offer is only half the drag reduction shown for the steady blowing case (6.5%), but accomplished this with a 74% reduction in mass flow.

Jones, Gregory S.↗

NASA NTRS2018

Numerical Simulation of a Simplified High-Lift CRM Configuration Embedded with Fluidic Actuators

Numerical simulations have been performed for a simplified high-lift configuration that is representative of a modern transport airplane. This configuration includes a leading-edge slat, fuselage, wing, nacelle-pylon and a simple hinged flap. The suction surface of the flap is embedded with multiple rows of fluidic actuators to reduce the extent of reversed flow regions and improve the aerodynamic performance of the configuration with flap in a deployed state. In the current paper, a Lattice Boltzmann Method based high-fidelity computational fluid dynamics (CFD) code, known as PowerFLOW® is used to simulate the entire flow field associated with this configuration, including the flow inside the actuators. A fully compressible version of the PowerFLOW® code that has been validated for high speed flows is used for the present simulations to accurately represent the transonic flow regimes that are encountered in the flow field generated by the actuators operating at higher mass flow (momentum) rates required to mitigate reverse flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient active flow control (AFC) systems and actuator arrangement for lift augmentation are emerging based on the parametric studies conducted here prior to wind tunnel tests. These numerical solutions will be compared with experimental data, once such data becomes available.

Vatsa, Veer N.↗

NASA NTRS2019

Effect of Loading Configuration on Kinematics and Kinetics for Deadlift and Squat Exercises: Case Study in Modeling Exercise Countermeasure Device for Astronauts

This study compares squat and deadlift exercises performed with two different loading configurations: 1) on a novel single-cable resistance exercise countermeasure device (ECD) for spaceflight and 2) with free weights. The results compare joint kinematics and kinetics between different loading configurations for each exercise, and also between the two exercises for each loading configuration. Single-cable versions of the squat (using a harness) and deadlift (using a T-bar) performed on the Hybrid Ultimate Lifting Kit (HULK) ECD have significantly different sagittal plane joint angle kinematics (both peak angle and range of motion) as well as joint kinetics (both peak joint moment and joint impulse) vs. their free weight equivalents at the same load. Differences also exist in hip abduction and rotation. Overall, the single-cable configurations tend to reduce peak joint angles, ranges of motion, peak joint moment and joint impulse vs. free weights. A notable exception is the lumbar joint, which is more heavily loaded for single-cable squats vs. free weight squats. This may have implications for both training benefit and possible risk of injury. Deadlift and squat exercises work the lower body musculature in different ways, with the deadlift emphasizing hip and lumbar extension and the squat emphasizing knee extension. Based on these findings, we would advocate the use of both movements in the exercise prescriptions of astronaut crews on deep-space missions.

Resistance Exercise↗

NASA NTRS2017

A Sweeping Jet Application on a High Reynolds Number Semispan Supercritical Wing Configuration

The FAST-MAC circulation control model was modified to test an array of unsteady sweeping-jet actuators at realistic flight Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center. Two types of sweeping jet actuators were fabricated using rapid prototype techniques, and directed over a 15% chord simple-hinged flap. The model was configured for low-speed high-lift testing with flap deflections of 30° and 60°, and a transonic cruise configuration with a 0° flap deflection. For the 30° flap high-lift configuration, the sweeping jets achieved comparable lift performance in the separation control regime, while reducing the mass flow by 54% as compared to steady blowing. However, the sweeping jets were not effective for the 60° flap. For the transonic cruise configuration, the sweeping jets reduced the drag by 3.3% at an off design condition. The drag reduction for the design lift coefficient for the sweeping jets provided only half the drag reduction shown for the steady blowing case (6.5%), but accomplished this with a 74% reduction in mass flow.

Gregory S Jones↗

NASA NTRS2020

Mars Ascent Vehicle Hybrid Propulsion Configuration

As part of a Mars Sample Return (MSR) campaign, two Mars Ascent Vehicle (MAV) configurations have been designed in parallel. Each ascent vehicle configuration has a different propulsion system which ultimately leads to two unique vehicle designs. As part of a Preliminary Architecture Assessment (PAA), these vehicle designs were developed to the same level of maturity in order to inform the selection of one of the vehicles as the point of departure design for the campaign. The selection will be made in November 2019. The initial MSR architecture called for a hybrid-based propulsion MAV. This type of propulsion system calls for a solid wax motor that would utilize liquid MON-25 as an oxidizer. Hybrid rocket propulsion allows for more flexibility than traditional solid or liquid propulsion options, and typically benefits from the advantages of both. A hybrid motor can be throttled and shut down easily, and avoids significant risk in manufacturing and handling. On a theoretical level, hybrid motors perform at a higher specific impulse (Isp) than solid motors. The primary disadvantage of hybrid motors comes from additional complexity and significantly less flight heritage and low Technology Readiness Level (TRL). This paper describes the design of the hybrid propulsion configuration. An additional paper will be published describing the design of the solid propulsion configuration1. The hybrid propulsion configuration MAV was developed in 2019 by NASA Marshall Space Flight Center (MSFC) in association with NASA Jet Propulsion Laboratory (JPL). It features a Single Stage to Orbit (SSTO) design with an SP7A solid wax fuel and MON-25 liquid oxidizer. The liquid portion of the vehicle allows for a Liquid Injection Thrust Vector Controller (LITVC) as well as hypergolic propellant additives for ignition. The vehicle was designed to deliver approximately 0.31kg of Martian geological samples to a circular orbit at Mars of 343km at a 25o inclination. Although hybrid propulsion in general has been used on launch vehicles in the past, the integrated vehicle subsystems that operate in conjunction with these propulsion elements do not typically operate in a Martian environment, which in this application can get as cold as -40oC. The PAA advanced the maturity of these subsystems by performing detailed design and analysis on the vehicle with respect to structures and mechanisms, Guidance/Navigation/Control (GNC) systems, avionics, Reaction Control System (RCS), LITVC, thermal environments, and advanced Computational Fluid Dynamics (CFD). This paper will summarize the results of these studies.

Yaghoubi, Darius↗

NASA NTRS2019

An Exploration of the Performance and Acoustic Characteristics of UAV-Scale Stacked Rotor Configurations

As interest grows in rotor- and propeller-driven electric vertical takeoff and landing (eVTOL) aircraft for the Urban Air Mobility market, there is a potential for previously studied concepts to reemerge due to the opportunities afforded by novel technologies and operating modes. One such concept is the “stacked” rotor, which consists of multiple co-rotating rotors positioned co-axially with a small axial offset. The goal of the work presented in this paper is to determine whether stacked rotors offer a compelling advantage for eVTOL aircraft in terms of both performance and acoustic characteristics. Results are presented for new experimental tests and computational modeling of multiple stacked rotor configurations, and comparisons are made with conventional rotor configurations. Testing of thirteen separate configurations— each using the same blade shape—revealed a configuration that resulted in an increase in the rotor power loading efficiency by more than 7% and reduced noise by more than 3 dBA when compared with a conventional rotor with all blades located in the same rotational plane.

Whiteside, Siena K. S.↗

NASA NTRS2020

Streak Instability Analysis for BOLT Configuration

The BOLT configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. A numerical study of the boundary layer instabilities over this configuration has been performed with the goal of applying state-of-the-art tools in multidimensional stability analysis that complement the other ongoing research related to the BOLT flight campaign. Specifically, the paper outlines modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane of a 1/3 rd scale BOLT configuration that was tested in the low-disturbance hypersonic wind tunnel at Purdue University and both quiet and conventional tunnels at Texas A&M University (TAMU). The basic state computations agree well with the heat flux measurements in the Purdue quiet tunnel as well as with the off-body velocity field described in a previous DNS study at the University of Minnesota. The encouraging agreement between the predicted frequency spectra of the streak instability in the region of increased boundary layer thickness and the surface pressure spectra measured during the TAMU experiments suggests that these streak instabilities may play an important role during the transition process near the symmetry plane. The modest value of the predicted peak N-factor (N max ≈ 5) for the streak instabilities provides a potential explanation for why transition is not observed under quiet flow conditions, but may occur in a noisy wind tunnel. Similar instability analyses are performed for the flight configuration at two selected flow conditions from the ascent portion of the planned flight trajectory. The predicted values of the peak N-factor suggest that transition onset in the vicinity of the center plane is possible at the ascent time of t = 26.98 seconds (N max ≈ 12.5 at X/L = 0.77), but the streak instabilities weaken sufficiently at the later time of t = 28.88 seconds (N max ≈ 11.5 at X/L ≈ 1.00) and are less likely to cause transition at that time.

Laminar turbulent transition↗

NASA NTRSDate not supplied

3D Climate Simulations of Earth-Like Planets with A Range of Atmospheric Composition, Radiative Transfer, Ocean, And Resolution Configurations, Using the New Version of ROCKE-3D

Understanding the climate of terrestrial planetary atmospheres has been increasingly the focus of research worldwide, in light of the increasing amount of rocky planet discoveries orbiting other stars in or near their habitable zone. Here we present simulations with the new version of the 3D climate model ROCKE-3D, whose version 2.0 will soon become publicly available. A wide range of configurations will be supported, compared to a handful ones in its predecessor, version 1.0 (Way et al., 2017). These include two model resolutions (4x5 and 2x2.5), two radiation schemes (GISS and SOCRATES), three atmospheric configurations (Earth-like, Earth-like without O3 and aerosols, and N2-dominated), and three ocean setups (prescribed sea-surface temperatures and ice cover, q-flux, and dynamic). Simulations of all different configuration combinations have been performed and will become available for use by the community. Key results will be presented across those configurations, together of the role of the structural uncertainty in model setup in the resulting climate calculated by the model.

climate simulations of Earth-like planets↗

NASA NTRS2020

An Over-the-Rotor Liner Investigation with Configurations Enabled by Additive Manufacturing

This paper presents the results of an investigation of over-the-rotor acoustic liner configurations enabled by additive manufacturing. NASA Langley and Glenn Research Centers have collaborated on the usage of acoustic liners in the turbofan aircraft engine nacelle wall at or very near the tip of the rotor. These liners absorb rotor-alone and rotor-stator interaction noise and, due to their proximity to the rotor tips, serve as a pressure release to inhibit the amount of generated noise. Initial tests with a metallic foam liner demonstrated good acoustic results, but there was concern regarding the durability of the material. NASA then decided to explore configurations enabled by additive manufacturing via tests in the NASA Langley Normal Incidence Tube. Measured data for uniform-depth and variable-depth cores with narrow and wide chambers were compared with predictions via the NASA Langley impedance prediction model. As these configurations were intended for eventual use in an over-the-rotor application, it was necessary to add facesheets to the wide-chamber cores to avoid deleterious flow effects caused by open cavities. A number of facesheets were tested in combination with each wide-chamber core. Finally, it has been shown that grooves near the rotor tips cause an improvement in aerodynamic performance. A small set of grooves were fabricated such that they could be combined with the wide-chamber configurations. The results of these tests were subsequently used to guide designs for further testing in higher technology readiness level test rigs at NASA Glenn Research Center.

acoustic↗

NASA NTRSDate not supplied

Airframe Noise Simulations of a Full-Scale Large Civil Transport in Landing Configuration

This paper summarizes the results obtained from an extensive computational campaign to accurately predict full-scale landing gear noise for large civil transports. A highly accurate digital model of a full-scale Boeing 777-300ER aircraft with as-flown nose and main landing gear components was developed for use in the simulations. Two aircraft configurations were selected: nose and main landing gear deployed with wing high-lift devices retracted, and nose and main landing gear deployed with wing high-lift devices deflected. The two configurations were simulated without and with toboggan fairings installed on the main gear to represent the principal configurations evaluated during the 2005 QTD2 flight test. All simulations were performed with the lattice Boltzmann solver PowerFLOW® to resolve and capture the highly complex, unsteady flow field in the immediate vicinity of the aircraft. The far-field noise sig-nature of the aircraft was computed via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable surface enclosing the source regions used as input. Synthetic pressure records at ground array microphone locations used during the QDT2 test were employed to generate narrowband acoustic maps and integrated far-field noise spectra. With high-lift devices retracted, the predicted spectra showed that landing gear noise is equivalent to total airframe noise, with no other airframe sources appearing within 10 dB of gear peak levels. Application of a toboggan fairing to the main gear produced modest noise reductions of 1-2 dB across the resolved frequency range. With high-lift devices deflected, undercarriage noise was within 3-4 dB of the total airframe noise, thus comprising nearly half of the total airframe noise. For this configuration, the toboggan fairing did not produce a reduction in noise, corroborating trends previously observed in QTD2 flight test data.

airframe noise↗

NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗

NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗

NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗

NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗