Search NASA⌕ Search

SEARCH · Search NASA

Results for “Designs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

The Study of the Relationship between Probabilistic Design and Axiomatic Design Methodology

Structural failure is rarely a "sudden death" type of event, such sudden failures may occur only under abnormal loadings like bomb or gas explosions and very strong earthquakes. In most cases, structures fail due to damage accumulated under normal loadings such as wind loads, dead and live loads. The consequence of cumulative damage will affect the reliability of surviving components and finally causes collapse of the system. The cumulative damage effects on system reliability under time-invariant loadings are of practical interest in structural design and therefore will be investigated in this study. The scope of this study is, however, restricted to the consideration of damage accumulation as the increase in the number of failed components due to the violation of their strength limits.

Onwubiko, Chin-Yere↗
NASA NTRS1950

Investigation of Performance of Axial-Flow Compressor of XT-46 Turbine-Propeller Engine. II - Performance of Revised Compressor at Design Equivalent Speed: Performance of Revised Compressor at Design Equivalent Speed - II

The compressor from the XT-46 turbine-propeller engine was revised by removing the last two rows of stator blades and by eliminating the interstage leakage paths described in a previous report. With the revised compressor, the flow choking point shifted upstream into the last rotor-blade row but the maximum weight flow was not increased over that of the original compressor. The flow range of the revised compressor was reduced to about two-thirds that obtained with the original compressor. The later stages of the compressor did not produce the design static-pressure increase probably because of excessive boundary-layer build-up in this region. Measurements obtained in the ninth-stage stator showed that the performance up to this station was promising but that the last three stages of the compressor were limiting the useful operating range of the preceding stages. Some modifications in flow-passage geometry and blade settings are believed to be necessary, however, before any major improvements in over-all compressor performance can be obtained.

Creagh, John W. R.↗
NASA NTRS2005

Optimal Design of Integrated Systems Health Management (ISHM) Systems for improving safety in NASA's Exploration Vehicles: A Two-Level Multidisciplinary Design Approach

In this paper, a two-level multidisciplinary design approach is described to optimize the effectiveness of ISHM s. At the top level, the overall safety of the mission consists of system-level variables, parameters, objectives, and constraints that are shared throughout the system and by all subsystems. Each subsystem level will then comprise of these shared values in addition to subsystem-specific variables, parameters, objectives and constraints. A hierarchical structure will be established to pass up or down shared values between the two levels with system-level and subsystem-level optimization routines.

Tumer, Irem↗
NASA NTRS2005

A Robotics Systems Design Need: A Design Standard to Provide the Systems Focus that is Required for Longterm Exploration Efforts

The United States is entering a new period of human exploration of the inner Solar System, and robotic human helpers will be partners in that effort. In order to support integration of these new worker robots into existing and new human systems, a new design standard should be developed, to be called the Robot-Systems Integration Standard (RSIS). It will address the requirements for and constraints upon robotic collaborators with humans. These workers are subject to the same functional constraints as humans of work, reach, and visibility/situational awareness envelopes, and they will deal with the same maintenance and communication interfaces. Thus, the RSIS will be created by discipline experts with the same sort of perspective on these and other interface concerns as human engineers.

Dischinger, H. Charles., Jr.↗
NASA NTRS2011

Comparison of Resource Requirements for a Wind Tunnel Test Designed with Conventional vs. Modern Design of Experiments Methods

The factors that determine data volume requirements in a typical wind tunnel test are identified. It is suggested that productivity in wind tunnel testing can be enhanced by managing the inference error risk associated with evaluating residuals in a response surface modeling experiment. The relationship between minimum data volume requirements and the factors upon which they depend is described and certain simplifications to this relationship are realized when specific model adequacy criteria are adopted. The question of response model residual evaluation is treated and certain practical aspects of response surface modeling are considered, including inference subspace truncation. A wind tunnel test plan developed by using the Modern Design of Experiments illustrates the advantages of an early estimate of data volume requirements. Comparisons are made with a representative One Factor At a Time (OFAT) wind tunnel test matrix developed to evaluate a surface to air missile.

DeLoach, Richard↗
NASA NTRS2014

Lean Mission Operations Systems Design - Using Agile and Lean Development Principles for Mission Operations Design and Development

The Resource Prospector Mission seeks to rove the lunar surface with an in-situ resource utilization payload in search of volatiles at a polar region. The mission operations system (MOS) will need to perform the short-duration mission while taking advantage of the near real time control that the short one-way light time to the Moon provides. To maximize our use of limited resources for the design and development of the MOS we are utilizing agile and lean methods derived from our previous experience with applying these methods to software. By using methods such as "say it then sim it" we will spend less time in meetings and more time focused on the one outcome that counts - the effective utilization of our assets on the Moon to meet mission objectives.

Operations↗
NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗
NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗