SEARCH · Search NASA

Results for “FLOW - CHANNELS, CURVED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS2008

Configuration Effects on Acoustic Performance of a Duct Liner

Continued success in aircraft engine noise reduction necessitates ever more complete understanding of the effect that flow path geometry has on sound propagation in the engine. The Curved Duct Test Rig (CDTR) has been developed at NASA Langley Research Center to investigate sound propagation through a duct of comparable size (approximately the gap of GE90) and physical characteristics to the aft bypass duct of typical aircraft engines. The liner test section is designed to mimic the outer/inner walls of an engine exhaust bypass duct that has been unrolled circumferentially. Experiments to investigate the effect of curvature along the flow path on the acoustic performance of a test liner are performed in the CDTR and reported in this paper. Flow paths investigated include both straight and curved with offsets from the inlet to the discharge plane of and 1 duct width, respectively. The test liners are installed on the side walls of the liner test section. The liner samples are perforate over honeycomb core, which design is typical of liners installed in aircraft nacelles. In addition to fully treated side walls, combinations of treated and acoustically rigid walls are investigated. While curvature in the hard wall duct is found not to reduce the incident sound significantly, it does cause mode scattering. It is found that asymmetry of liner treatment causes scattering of the incident mode into less attenuated modes, which degrades the overall liner attenuation. It is also found that symmetry of liner treatment enhances liner performance by eliminating scattering into less attenuated modes. Comparisons of measured liner attenuation with numerical results predicted by an analytic model based on the parabolic approximation (CDUCT-LaRC) have also been made and are reported in this paper. The effect of curvature in the rigid wall configuration estimated by CDUCT-LaRC is similar to the observed results, and the mode scattering seen in the measurements also occurs in the analytic model results. The analytic model and experiment show similar differences of overall attenuation between one wall treated and both walls treated.

Gerhold, Carl H.↗

NASA NTRS2003

Computational Hemodynamic Simulation of Human Circulatory System under Altered Gravity

A computational hemodynamics approach is presented to simulate the blood flow through the human circulatory system under altered gravity conditions. Numerical techniques relevant to hemodynamics issues are introduced to non-Newtonian modeling for flow characteristics governed by red blood cells, distensible wall motion due to the heart pulse, and capillary bed modeling for outflow boundary conditions. Gravitational body force terms are added to the Navier-Stokes equations to study the effects of gravity on internal flows. Six-type gravity benchmark problems are originally presented to provide the fundamental understanding of gravitational effects on the human circulatory system. For code validation, computed results are compared with steady and unsteady experimental data for non-Newtonian flows in a carotid bifurcation model and a curved circular tube, respectively. This computational approach is then applied to the blood circulation in the human brain as a target problem. A three-dimensional, idealized Circle of Willis configuration is developed with minor arteries truncated based on anatomical data. Demonstrated is not only the mechanism of the collateral circulation but also the effects of gravity on the distensible wall motion and resultant flow patterns.

Kim. Chang Sung↗

NASA NTRS2000

Measurements in a Transitional Boundary Layer Under Low-Pressure Turbine Airfoil Conditions

This report presents the results of an experimental study of transition from laminar to turbulent flow in boundary layers or in shear layers over separation zones on a convex-curved surface which simulates the suction surface of a low-pressure turbine airfoil. Flows with various free-stream turbulence intensity (FSTI) values (0.5%, 2.5% and 10%), and various Reynolds numbers (50,000, 100,000 200,000 and 300,000) are investigated. Reynold numbers in the present study are based on suction surface length and passage exit mean velocity. Flow separation followed by transition within the separated flow region is observed for the lower-Re cases at each of the FSTI levels. At the highest Reynolds numbers and at elevated FSn, transition of the attached boundary layer begins before separation, and the separation zone is small. Transition proceeds in the shear layer over the separation bubble. For both the transitional boundary layer and the transitional shear layer, mean velocity, turbulence intensity and intermittency (the fraction of the time the flow is turbulent) distributions are presented. The present data are compared to published distribution models for bypass transition, intermittency distribution through transition, transition start position, and transition length. A model developed for transition of separated flows is shown to adequately predict the location of the beginning of transition, for these cases, and a model developed for transitional boundary layer flows seems to adequately predict the path of intermittency through transition when the transition start and end are known. These results are useful for the design of low-pressure turbine stages which are known to operate under conditions replicated by these tests.

Simon, Terrence W.↗

DOE OSTI2020

Adaptive Multirate Mass Transfer (aMMT) Model: A New Approach to Upscale Regional‐Scale Transport Under Transient Flow Conditions

Abstract The long‐term evaluation of regional‐scale groundwater quality needs efficient upscaling methods for transient flow. Upscaling techniques, such as the Multirate Mass Transfer (MRMT) method with constant upscaling parameters, have been used for transport with steady‐state flow, yet the upscaling parameters (i.e., rate coefficients) may be time dependent. This study proposed and validated an adaptive MRMT (aMMT) method by allowing the mass transfer coefficients in MRMT to change with the flow field. Advective‐dispersive contaminant transport simulated in a 3‐D heterogeneous medium was used as a reference solution. Equivalent transport under homogeneous flow conditions was evaluated by applying the MRMT and aMMT models for upscaling. The relationship between mass transfer coefficients and flow rates was fitted under steady‐state flow driven by various hydraulic gradients. A power law relationship was obtained, which was then used to update the mass transfer coefficients in each stress period under transient flow conditions in the aMMT method. Results indicated that for advection‐dominated transport, both the MRMT and aMMT methods can upscale the anomalous transport dynamics affected by subgrid heterogeneity under transient flow conditions. Whereas for diffusion‐dominated systems, the MRMT model failed to capture the tails of tracer breakthrough curves after the boundary condition changed, but the results from the aMMT model were significantly improved. However, if the overall flow direction changed, both MRMT and aMMT failed to represent the breakthrough curve tail generated by the heterogeneous system. The results point toward a promising path for upscaling transport in complex aquifers with transient flow.

Guo, Zhilin↗

DOE OSTI2026

INL Intern Poster Session

Characterization of off-gas constituents from nuclear fuel reprocessing can be measured using a residual gas analyzer. Characterization of this off-gas is important in a closed fuel cycle, where gasses such as Nox, Kr, I, and C-14 need to be removed from reprocessing plants to meet regulatory requirements. Both Kr and Xe have low chemical reactivity, making capture and separation difficult. Solid sorbents can be used to capture these gases as an alternative to cryogenic distillation, which is energy intensive and hazardous. AgZ-PAN and HZ-PAN are two solid sorbents that have demonstrated selective capture of Xe and Kr. A residual gas analyzer can be used to obtain breakthrough curves that demonstrate how well this adsorption and separation occur. The breakthrough curve is dependent on packing density, column size, and flow rate. Data obtained from the RGA was verified with a gas chromatographer.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1991

Viscous equilibrium computations using program LAURA

The Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) has been modified to compute viscous equilibrium flow. Periodic calls to the thermodynamic and transport property curve-fits enable solutions to be computed for small percentage increase in computer time when compared with perfect gas times. The code is used to compute the hypersonic flow over slender and blunt cones, and solutions are compared with other computational techniques and flight data.

Greene, Francis A.↗

NASA NTRSDate not supplied

CFD Predictions of Boiling Regime Transitions during Line Chilldown validated against a 1G LN2 Experiment

Introduction Before filling a propellant tank on the ground or in Space, the transfer line between the donor and receiver tanks must be cooled down preferably by sacrificing a minimum amount of the cryogenic fluid. The cryogenic line chill-down process involves a transition between different flow boiling regimes, namely, film boiling, transition film boiling, and nucleate boiling which are complex and may be quite gravity-dependent. Capturing these boiling phenomena and predicting the transition between them in a CFD framework is new and challenging both for 1g and microgravity applications. Materials & Methods The present work addresses this challenge by employing a two-phase Eulerian approach in the context of a homogeneous fluid mixture together with the Lee phase change model to capture the film boiling regime of the chill-down process using ANSYS Fluent®. The nucleate boiling regime is predicted by incorporating an in-house developed sub-grid model that accounts for bubble nucleation, bubble growth, bubble departure diameter, and their shedding frequency. The sub-grid model is encoded and implemented into Fluent via a user-defined function for the wall-fluid heat flux calculations. The mathematical formulation and numerical implementation of the CFD model are described in detail. The coupled CFD-Subgrid model is validated against published experimental data for liquid nitrogen chill-down of a heated stainless-steel pipe in 1g. Results Numerical simulation results show good agreements between the CFD predictions of the wall temperature evolution, rewetting temperature, and transition between film and nucleate boiling, with the experimental measurements published by Darr et al [2] for several different LN2 flowrates in the vertical pipe orientation. The CFD predictions for the wall temperature distribution indicate a rapid quenching of the wall at two upstream and downstream temperature sensing locations as compared to the experimental measurement. The only tuning parameter in the CFD model is the Lee mass transfer coefficient. The CFD Model predicts the Liedenfrost rewetting temperature in close agreement with the experiment. This marks a transition between stable and transitionary flow boiling regimes. The CFD-predicted boiling curve for the downstream sensor location is also compared against its experimental counterpart and indicates that the model is able to predict all the key temperature and heat flux parameters during the transitions from stable to transitionary film boiling to nucleate boiling in close agreement with the experiment. A sequence of predicted volume fraction, and temperature contours depicting these transitions will be presented.

Evaporation Condensation↗

NASA NTRS1950

The Boundary Layers in Fluids with Little Friction

The vortices forming in flowing water behind solid bodies are not represented correctly by the solution of the potential theory nor by Helmholtz's jets. Potential theory is unable to satisfy the condition that the water adheres at the wetted bodies, and its solutions of the fundamental hydrodynamic equations are at variance with the observation that the flow separates from the body at a certain point and sends forth a highly turbulent boundary layer into the free flow. Helmholtz's theory attempts to imitate the latter effect in such a way that it joins two potential flows, jet and still water, nonanalytical along a stream curve. The admissibility of this method is based on the fact that, at zero pressure, which is to prevail at the cited stream curve, the connection of the fluid, and with it the effect of adjacent parts on each other, is canceled. In reality, however, the pressure at these boundaries is definitely not zero, but can even be varied arbitrarily. Besides, Helmholtz's theory with its potential flows does not satisfy the condition of adherence nor explain the origin of the vortices, for in all of these problems, the friction must be taken into account on principle, according to the vortex theorem.

Blasius, H.↗

NASA NTRS1998

Analysis of Linear Aerospike Plume Induced X-33 Base Heating Environment

Computational analysis is conducted to study the effect of an linear aerospike engine plume on the X-33 base-heating environment during ascent flight. To properly account for the freestream-body interaction and to allow for potential plume-induced flow-separation, the thermo-flowfield of the entire vehicle at several trajectory points is computed. A sequential grid-refinement technique is used in conjunction with solution-adaptive, patched, and embedded grid methods to limit the model to a manageable size. The computational methodology is based on a three-dimensional, finite-difference, viscous flow, chemically reacting, pressure-based computational fluid dynamics formulation, and a three-dimensional, finite-volume, spectral-line based weighted-sum-of-gray-gases absorption, computational radiation heat transfer formulation. The computed forebody and afterbody surface pressure coefficients and base pressure characteristic curves are compared with those of a cold-flow test. The predicted convective and radiative base-heat fluxes, the effect of base-bleed, and the potential of plume-induced flow separation are presented.

Wang, Ten-See↗

NASA NTRSDate not supplied

Fracture Prediction of Epoxy Resin using Morse Bond Potential Embedded in GAFF using Molecular Dynamics Simulations

A generic method is developed to investigate the fracture behavior of an epoxy resin using atomistic molecular (MD) dynamics simulations. The epoxy system consisted of the stoichiometric mixture of tetra-/tri-functional epoxies and di-functional hardener molecules and was cured with a step-growth crosslinking algorithm. A hybrid force field (hFF) in which Morse bond function were added in second generation-general Amber Force Field (GAFF2) was used to capture bond breaking of the crosslinked epoxy system under uniaxial deformation. The Morse bond parameters for covalent bonds in the crosslinked backbone were fit to dissociation curves computed by CASPT2/6-311+G**. After the systems in various crosslink densities were obtained and equilibrated, the full length of stress-strain (𝜎-𝜀) curve was produced including initial elastic regime, yielding, plastic flow, strain hardening, and progressive failure. We found that the hFF was effective in studying the dissociation of crosslinked polymers and understanding the failure mechanism. In the results, the hFF delivered the same elastic property obtained from the unmodified force field GAFF. The stress-strain curve, however, began to be distinct in the plastic regime due to broken covalent bonds capable of altering the tensile behavior. Once the stress reached maximum, it progressively decreased until the ultimate failure (𝜎=0). Since hFF employed the existing GAFF functions with including a minimal change of its bond potential, this approach is easier to perform and computationally more efficient for unveiling the fracture behavior of polymer materials at the molecular level than other approaches with reactive force fields. We expect this approach will be utilized to accelerate the material-by-design process for thermosets by incorporate data from molecular models.

Changwoon Jang↗

DOE OSTI2024

An experimental investigation on the CO 2 storage capacity of the composite confining system

Assuring secure containment of stored CO 2 is of paramount importance—for climate change mitigation, for permitting, and for reassuring the public. Regional seals, such as those sealing petroleum accumulations, have proven to be effective for securing CO 2 . However, the goal of permanent sequestration can also be satisfied with “composite confining systems” consisting of multiple, possibly discontinuous flow barriers that, in aggregate, create a system with very high permeability anisotropy and effectively retard the vertical migration of CO 2 . This study focuses on investigating the barrier characteristics necessary for effective containment of CO 2 , using both physical flow experiments and modified invasion percolation simulations. The simulations are calibrated to the physical experiments and are used to further extend the analysis. Results show that for a composite confining system, a) even barriers with low capillary entry pressure contrast to the underlying flow unit can divert rising CO 2 ; b) curved or anticlinal barrier topography can enhance CO 2 trapping; c) fining-upward gradations make little difference to barrier effectiveness or CO 2 retention; d) longer barriers retain more CO 2 regardless of barrier topography. Finally, field-scale simulations have demonstrated the importance of barrier length for increasing CO 2 storage capacity. Furthermore, the results presented can be used to inform the development of new screening criteria for characterization and effectiveness of composite confining systems.

58 GEOSCIENCES↗

NASA NTRS1991

A design strategy for the use of vortex generators to manage inlet-engine distortion using computational fluid dynamics

A reduced Navier-Stokes solution technique was successfully used to design vortex generator installations for the purpose of minimizing engine face distortion by restructuring the development of secondary flow that is induced in typical 3-D curved inlet ducts. The results indicate that there exists an optimum axial location for this installation of corotating vortex generators, and within this configuration, there exists a maximum spacing between generator blades above which the engine face distortion increases rapidly. Installed vortex generator performance, as measured by engine face circumferential distortion descriptors, is sensitive to Reynolds number and thereby the generator scale, i.e., the ratio of generator blade height to local boundary layer thickness. Installations of corotating vortex generators work well in terms of minimizing engine face distortion within a limited range of generator scales. Hence, the design of vortex generator installations is a point design, and all other conditions are off design. In general, the loss levels associated with a properly designed vortex generator installation are very small; thus, they represent a very good method to manage engine face distortion. This study also showed that the vortex strength, generator scale, and secondary flow field structure have a complicated and interrelated influence over engine face distortion, over and above the influence of the initial arrangement of generators.

Anderson, Bernhard H.↗

NASA NTRS1991

A design strategy for the use of vortex generators to manage inlet-engine distortion using computational fluid dynamics

Anderson, Bernhard H.↗

DOE OSTI2020

An extended trajectory-mechanics approach for calculating two-phase flow paths

A technique originating in quantum dynamics is used to derive a trajectory-based, semi-analytical solution for two-phase flow. The partial differential equation governing the evolution of the aqueous phase is equivalent to a family of ordinary differential equations defined along a path through the porous medium. The trajectories may be found by solving the differential equations directly or by post-processing the output of a numerical solution to the full set of governing equations. The trajectories, which differ from conventional streamlines, are found to bend downward in response to gravitational forces. The curvature is more pronounced as the dip of the porous layer containing the flow increases. Subtle changes in the relative permeability curve can lead to significant variations in the trajectories. The ordinary differential equation for the trajectory provides an expression for the travel time along the path. The expression produces a semi-analytical approximation to the model parameter sensitivities, the partial derivatives of the travel times with respect to changes in the permeability model. The semi-analytical trajectory-based sensitivities generally agree with those computed using a numerical reservoir simulator and a perturbation approach. The sensitivities are useful in tomographic imaging algorithms designed to estimate the spatial variation in permeability within a porous medium using multiphase observations.

58 GEOSCIENCES↗

NASA NTRS1985

Mean velocity and turbulence measurements in a 90 deg curved duct with thin inlet boundary layer

The experimental database established by this investigation of the flow in a large rectangular turning duct is of benchmark quality. The experimental Reynolds numbers, Deans numbers and boundary layer characteristics are significantly different from previous benchmark curved-duct experimental parameters. This investigation extends the experimental database to higher Reynolds number and thinner entrance boundary layers. The 5% to 10% thick boundary layers, based on duct half-width, results in a large region of near-potential flow in the duct core surrounded by developing boundary layers with large crossflows. The turbulent entrance boundary layer case at R sub ed = 328,000 provides an incompressible flowfield which approaches real turbine blade cascade characteristics. The results of this investigation provide a challenging benchmark database for computational fluid dynamics code development.

Crawford, R. A.↗

NASA NTRS1951

The Design of Variable Mach Number Asymmetric Super-Sonic Nozzles by Two Procedures Employing Inclined and Curved Sonic Lines

Two theoretical procedures are developed for designing asymmetric supersonic nozzles for which the calculated exit flow is nearly uniform over a range of Mach numbers. One procedure is applicable at Mach numbers less than approximately 3. This approach yields, without iteration, a nozzle for which the calculated exit flow is uniform at two Mach numbers and, with proper design, is nearly uniform at Mach numbers between, slightly above, and slightly below these two. The use of an inclined and curved sonic line is an essential feature of this approach, The second procedure requires iteration and is used far designs at Mach numbers exceeding 3. Although it is not a necessary feature, an inclined and curved sonic line is also used in this procedure. In both approaches the flow field dawn stream of the sonic line is determined using the method of characteristics.

Syvertson, Clarence A.↗

DOE OSTI2021

Serrated Flow in Alloy Systems

This chapter presents the problem of the complexity of plastic flow in alloys, which is manifested by serrated deformation curves and transient plastic strain localizations. This phenomenon, which uncovers an inherently collective nature of the dynamics of crystal defects, is well known for conventional alloys. Surprisingly, despite the particular microstructure of HEAs, which strongly impacts the microscopic dynamics of defects, not only the HEAs are prone to the macroscopically jerky flow, but the serration patterns display many similar features, thus bearing evidence to similar laws for the collective dynamics. To provide a comprehensive approach to this problem, the chapter is subdivided into two parts. The first part presents the state-of-the art of this research under the angle of distinct regimes of collective dislocation dynamics found in conventional alloys, e.g., self-organized criticality, deterministic chaos, or synchronization. The second part summarizes recent investigations into serrated flows in HEAs, uncovering common and specific types of behaviors. Both parts conclude with the formulation of diverse open questions concerning these strongly coupled fields of research.

Lebyodkin, Mikhail↗

NASA NTRS1950

Some Studies on the Flow of a Gas in the Region of Transition Through the Velocity of Sound

The two-dimensional motion of an incompressible fluid about a closed contour with a definite velocity in magnitude and direction at infinity is considered. If, without changing the direction of the velocity at infinity, the magnitude is increased, the configuration of the streamlines remains unchanged and only the numbering of the stream function changes. There exists only one family of curves that can serve as streamlines in the incompressible flow about a given contour (at a given angle of attack); for example, the contour of an airplane wing. The case is quite different with a compressible fluid.

Kiebel, I. A.↗