Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - DIFFUSERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

An experimental study on the effects of tip clearance on flow field and losses in an axial flow compressor rotor

Detailed measurement of the flow field in the tip region of a compressor rotor was carried out using a Laser Doppler Velocimeter (LDV) and a Kiel probe at two different tip clearance heights. At both clearance sizes, the relative stagnation pressure and the axial and tangential components of relative velocities were measured upstream, inside the passage and downstream of the rotor, up to about 20 percent of the blade span from the annulus wall. The velocities, outlet angles, losses, momentum thickness, and force defect thickness are compared for the two clearances. A detailed interpretation of the effect of tip clearance on the flow field is given. There are substantial differences in flow field, on momentum thickness, and performance as the clearance is varied. The losses increase linearly within the passage and their values increase in direct proportion to tip clearance height. No discernable vortex (discrete) is observed downstream of the rotor.

Lakshminarayana, B.↗
NASA NTRS1987

Intergration effects of D-shaped, underwing, aft-mounted, separate-flow, flow-through nacelles on a high-wing transport

An experimental investigation was conducted in the Langley 16-Foot Transonic Tunnel at freestream Mach numbers from 0.70 to 0.82 and angles of attack from -3.0 to 4.0 deg to determine the integration effects of D-shaped, underwing, aft-mounted, separate-flow, flow-through nacelles on a high-wing transonic transport configuration. The results showed that the aft-mounted nacelle/pylon produced an increase in lift over that of the wing-body configuration by pressurizing much of the wing lower surface in front of the pylon. For the D-shaped nacelle, a substantial region of supersonic flow over the wing, aft of the lip of the nacelle, cancelled the reduction in drag caused by the increase in pressures ahead of the lip, to increase interference and form drag compared with a similar circular-shaped nacelle. The installed drag of the D=shaped nacelle was essentially the same as that of an aft-mounted circular nacelle from a previous investigation.

Lamb, Milton↗
NASA NTRS1987

Graphics and Flow Visualization of Computer Generated Flow Fields

Flow field variables are visualized using color representations described on surfaces that are interpolated from computational grids and transformed to digital images. Techniques for displaying two and three dimensional flow field solutions are addressed. The transformations and the use of an interactive graphics program for CFD flow field solutions, called PLOT3D, which runs on the color graphics IRIS workstation are described. An overview of the IRIS workstation is also described.

Kathong, M.↗
NASA NTRS1988

A Study of Flow Separation in Transonic Flow Using Inviscid and Viscous Computational Fluid Dynamics (CFD) Schemes

A comparison of flow separation in transonic flows is made using various computational schemes which solve the Euler and the Navier-Stokes equations of fluid mechanics. The flows examined are computed using several simple two-dimensional configurations including a backward facing step and a bump in a channel. Comparison of the results obtained using shock fitting and flux vector splitting methods are presented and the results obtained using the Euler codes are compared to results on the same configurations using a code which solves the Navier-Stokes equations.

Rhodes, J. A.↗
NASA NTRS1988

On the generation of mean flows by the interaction of Goertler vortices and Tollmien-Schlichting waves in curved channel flows

There are many fluid flows where the onset of transition can be caused by different instability mechanisms which compete in the nonlinear regime. The interaction of a centrifugal instability mechanism with the viscous mechanism which causes Tollmein-Schlichting waves is discussed. The interaction between these modes can be strong enough to drive the mean state; the interaction is investigated in the context of curved channel flows so as to avoid difficulties associated with boundary layer growth. Essentially it was found that the mean state adjusts itself so that any modes present are neutrally stable even at finite amplitude. In the first instance, the mean state driven by a vortex of short wavelength in the absence of Tollmein-Schlichting waves is considered. It is shown that for a given channel curvature and vortex wavelength, there is an upper limit to the mass flow rate which the channel can support as the pressure gradient is increased. When the Tollmein-Schlichting waves are present, then the nonlinear differential equation to determine the mean state is modified.

Bassom, Andrew P.↗
NASA NTRS1987

Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. I - Measurement and analysis technique

This two-part paper presents laser anemometer measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan. The objective is to provide additional insight into unsteady blade-row interactions within highspeed compressors which affect stage efficiency, energy transfer, and other design considerations. Part 1 describes the measurement and analysis techniques used for resolving the unsteady flow field features. The ensemble-average and variance of the measured velocities are used to identify the rotor wake generated and unresolved unsteadiness, respectively. (Rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and the term unresolved unsteadiness refers to all remaining contributions to unsteadiness such as vortex shedding, turbulence, mass flow fluctutions, etc.). A procedure for calculating auto and cross correlations of the rotor wake generated and unresolved unsteady velocity fluctuations is described. These unsteady-velocity correlations have significance since they also result from a decomposition of the Navier-Stokes equations. This decomposition of the Navier-Stokes equations resulting in the velocity correlations used to describe the unsteady velocity field will also be outlined in this paper.

Suder, K. L.↗
NASA NTRS1989

Noise produced by turbulent flow into a rotor: Theory manual for atmospheric turbulence prediction and mean flow and turbulence contraction prediction

Prediction of helicopter main rotor noise due to ingestion of atmospheric turbulence was analyzed. The analysis combines several different models that describe the fluid mechanics of the turbulence and the ingestion process. Two models, atmospheric turbulence, and mean flow and turbulence contraction were covered. The third model, covered in a separate report, describes the rotor acoustic mode. The method incorporates the atmospheric turbulence model and a rapid distortion turbulence contraction description to determine the statistics of the anisotropic turbulence at the rotor plane. The analytical basis for a module was provided which was incorporated in NASA's ROTONET helicopter noise prediction program. The mean flow and turbulence statistics associated with the atmospheric boundary layer were modeled including effects of atmospheric stability length, wind speed, and altitude. The turbulence distortion process is modeled as a deformation of vortex filaments (which represent the turbulence field) by a mean flow field due to the rotor inflow.

Simonich, J. C.↗
NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

The present analyses of boundary layer flow and turbulence transport attempt to characterize the influence of freestream turbulence on the surface heat-transfer rate and stagnation point region skin friction of a circular cross-section cylinder in turbulent flow. The Reynolds stress-transport equations and k-epsilon two-equation turbulence modeling are used, yielding time-averaged turbulence double-correlations, mean-flow properties, surface heat-transfer rate, and skin-friction with freestream isotropic turbulence. A comparison of analytical results with experimental data indicates that large Reynolds normal stresses are induced at the boundary layer edge by the kinetic energy of the turbulence.

Wang, C. R.↗
NASA NTRS1989

Three-dimensional computations of cross-flow injection and combustion in a supersonic flow

A low-storage version of the SPARK3D code which is based on the temporally second-order accurate MacCormack (1969) explicit scheme is used to solve the governing equations for three-dimensional chemically reacting flows with finite-rate chemistry. The code includes a fourth-order compact spatial scheme capable of providing higher order spatial accuracy, and it is used to study two-dimensional linear advection, two-dimensional Euler flow, and three-dimensional viscous flow. Also considered are the injection, mixing, and combustion of hydrogen in a supersonic cross stream.

Carpenter, M. H.↗
NASA NTRS1988

A new look at wind tunnel flow quality for transonic flows

The implementation of several transonic hot wire anemometry techniques for obtaining fluctuating data related to wind tunnel flow quality has been evaluated. An overview of the theoretical considerations, calibration techniques, and related assumptions are discussed for the data presented from the LaRC 8' Transonic Pressure Tunnel. The impact of incorrect assumptions related to hot wire sensitivities are highlighted. Velocity, density, total temperature, and mass flow results from three-element, two-element, and single-element probes are presented in rms and spectral formats. Based on these comparisons, great caution should be used when relying on flow quality information obtained utilizing hot wire techniques other than the three-element technique.

Jones, Gregory S.↗
NASA NTRS1989

SSME LOX post flow analysis/fluid structure interaction. Volume 1: Flow analysis

The realization of measures to improve the performance of the Space Shuttle is, to a large extent, dependent on an improved understanding of the fluid flow phenomena occurring in the main engine. The overall arrangement of the primary components of the Space Shuttle Main Engine (SSME) are presented. The impingement of the hot gases from the transfer ducts onto the LOX posts causes them to be subjected to severe thermal and gas dynamic loads, which in the past have resulted in the occasional breakage of some elements of the outer row of posts during test firings of the engine, particularly at higher power levels. Large velocities in the gap between the LOX posts may also be a contributing factor in causing dynamic stability problems. The deforming structural response of the posts to the pressure loading may likely affect the gas flowfield by producing a moving flowfield boundary, thereby creating a dynamically coupled unsteady fluid-structure system. The objective was to investigate the three-dimensional, turbulent flow around a simplified SSME LOX post array using an existing Reynolds averaged Navier-Stokes flow solver and a suitable turbulence model to parameterize the turbulent shear stresses. Numerical computations were performed to analyze the effect on the flowfield of varying the spacing between the LOX posts, which were modeled as rigid, three-dimensional circular cylinders. The methodology used in the computations is described. Results are presented.

Burke, Roger W.↗
NASA NTRS1990

Design optimization of natural laminar flow fuselages in compressible flow

An optimization method has been developed to design axisymmetric body shapes such as fuselages, nacelles, and external fuel tanks with increased transition Reynolds numbers in subsonic compressible flow. The new design method involves a constraint minimization procedure coupled with analysis of the inviscid and viscous flow regions, and linear stability analysis of the compressible boundary layer. Boundary-layer transition is predicted by a 'hybrid' transition criterion based on Granville's transition criterion and a criterion using linear stability theory coupled with the e(n)-method. A tiptank of a business-jet is used as an example to illustrate that the method can be utilized to design an axisymmetric body shape with extensive natural laminar flow. Boundary layer transition is predicted to occur at a transition Reynolds number of 6.04 x 10 to the 6th on the original tiptank. On the designed body shape, a transition Reynolds number of 7.22 x 10 to the 6th is predicted using compressible linear stability theory coupled with e(n)-method.

Dodbele, Simha S.↗
NASA NTRS1990

Flow downstream of the heliospheric terminal shock. I - Irrotational flow

Recent reports of remote detection of the heliospheric terminal shock place it near 50 AU. These conflict with standard models which, when combined with current data on the local interstellar medium, place the shock beyod 100 AU. Resolution of this discrepancy has led to hypotheses that invoke cosmic ray pressure, momentum exchange with interstellar neutrals, and magnetic field effects between the shock and the contact discontinuity dividing the solar wind from interstellar plasma. These hypotheses depend not only on properties of the interstellar medium, but also on the downstream three-dimensional flow between the shock and the contact discontinuity, in the region called the 'heliosheath'. The downstream flow field in the absence of magnetic fields is examined here under the assumptions that the flow everywhere outside the shock can be approximated as irrotational and incompressible. It is found, in particular, that the distance between the terminal shock and the contact discontinuity is less than the heliocentric distance to the terminal shock, effectively eliminating magnetic field effects in the heliosheath as being dynamically important.

Suess, Steven T.↗
NASA NTRS1991

Hysteresis and the transition between axisymmetric flow and wave flow in the baroclinic annulus

A numerical model is employed to establish the transitions between axisymmetric flow and wave flow in the rotating, differentially heated annulus experiments of Fein for both rigid lid and free surface cases. It is shown that, for most of the transitions, the method of computing a steady axisymmetric flow and then testing its linear stability to wave disturbance results in good agreement with the experiments. Implications for the investigation of the dynamics of the earth's atmosphere are considered.

Miller, Timothy L.↗
NASA NTRS1990

The flow of a thin liquid film on a stationary and rotating disk. I - Experimental analysis and flow visualization

The mean thickness of a thin liquid film of deionized water with a free surface on a stationary and rotating horizontal disk has been measured with a nonobtrusive capacitance technique. The measurements were taken when the rotational speed was 0-300 RPM and the flow rate was 7.0-15.0 LPM. A flow visualization study of the thin film was also performed to determine the characteristics of the waves on the free surface. When the disk was stationary, a circular hydraulic jump was present on the disk. Surface waves were found in the supercritical and subcritical regions at all flow rates studied. When the rotational speed of the disk is low, a standing wave at the edge of the disk was present. As the rotational speed increased, the surface waves changed from the wavy-laminar region to a region in which the waves ran nearly radially across the disk on top of a thin substrate of fluid.

Thomas, S.↗
NASA NTRS1991

Computational and experimental aftbody flow fields for hypersonic, airbreathing configurations with scramjet exhaust flow simulation

Computational results are presented for three issues pertinent to hypersonic, airbreathing vehicles employing scramjet exhaust flow simulation. The first issue consists of a comparison of schlieren photographs obtained on the aftbody of a cruise missile configuration under powered conditions with two-dimensional computational solutions. The second issue presents the powered aftbody effects of modeling the inlet with a fairing to divert the external flow as compared to an operating flow-through inlet on a generic hypersonic vehicle. Finally, a comparison of solutions examining the potential of testing powered configurations in a wind-off, instead of a wind-on, environment, indicate that, depending on the extent of the three-dimensional plume, it may be possible to test aftbody powered hypersonic, airbreathing configurations in a wind-off environment.

Huebner, Lawrence D.↗
NASA NTRS1992

MHD flow past an obstacle - Large-scale flow in the magnetosheath

As a step to the study of the large-scale flow in the magnetosheath, the MHD flow past an obstacle is investigated. A time asymptotic method is used to obtain 3D steady-state solutions. The results indicate the formation of a depletion layer near the obstacle due to the increase of the magnetic field. Along the earth-sun line the plasma density increases first and then decreases from the post bow shock to the magnetopause. The local density maximum in front of the magnetopause may correspond to what was recently observed. When the interplanetary magnetic field direction is tilted from the solar wind flow, the IMF influences the shape of the bow shock as well as the location of the stagnation point at the magnetopause in a way consistent with observation. In addition, the results show the existence of a magnetosheath current in the post parallel-shock region.

Wu, C. C.↗
NASA NTRS1992

Design optimization of natural laminar flow bodies in compressible flow

An optimization method has been developed to design axisymmetric body shapes such as fuselages, nacelles, and external fuel tanks with increased transition Reynolds numbers in subsonic compressible flow. The new design method involves a constraint minimization procedure coupled with analysis of the inviscid and viscous flow regions and linear stability analysis of the compressible boundary-layer. In order to reduce the computer time, Granville's transition criterion is used to predict boundary-layer transition and to calculate the gradients of the objective function, and linear stability theory coupled with the e(exp n)-method is used to calculate the objective function at the end of each design iteration. Use of a method to design an axisymmetric body with extensive natural laminar flow is illustrated through the design of a tiptank of a business jet. For the original tiptank, boundary layer transition is predicted to occur at a transition Reynolds number of 6.04 x 10(exp 6). For the designed body shape, a transition Reynolds number of 7.22 x 10(exp 6) is predicted using compressible linear stability theory coupled with the e(exp n)-method.

Dodbele, Simha S.↗