SEARCH · Search NASA

Results for “Finite Element Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Multi-Terrain Impact Testing and Simulation of a Composite Energy Absorbing Fuselage Section

Comparisons of the impact performance of a 5-ft diameter crashworthy composite fuselage section were investigated for hard surface, soft soil, and water impacts. The fuselage concept, which was originally designed for impacts onto a hard surface only, consisted of a stiff upper cabin, load bearing floor, and an energy absorbing subfloor. Vertical drop tests were performed at 25-ft/s onto concrete, soft-soil, and water at NASA Langley Research Center. Comparisons of the peak acceleration values, pulse durations, and onset rates were evaluated for each test at specific locations on the fuselage. In addition to comparisons of the experimental results, dynamic finite element models were developed to simulate each impact condition. Once validated, these models can be used to evaluate the dynamic behavior of subfloor components for improved crash protection for hard surface, soft soil, and water impacts.

Fasanella, Edwin L.↗

NASA NTRS2007

Multi-Terrain Impact Testing and Simulation of a Composite Energy Absorbing Fuselage Section

Fasanella, Edwin L.↗

NASA NTRSDate not supplied

Applicability of Loads Estimation Techniques Using Sparse Acceleration Sensor Data to Spacecraft Structural Health Monitoring

The use of structural health monitoring systems on spacecraft structures can play a crucial role in ensuring the safety, reliability, and longevity of the structure by gathering and analyzing onboard sensor data. Of specific importance is monitoring for excessive loading at critical interfaces as any off-nominal structural excitations experienced by spacecraft structures can cause early unpredicted high structural life consumption or damage. The availability and cost of flight-certified sensors along with the size of spacecraft structures and allowable payload mass drives the need for a method to estimate loads using sparsely-located sensors. Numerous approaches such as physics-based, statistical learning, and physics-enhanced statistical learning algorithms have gained popularity among structural prognostics applications. However, developing noise-robust prediction models to assess loads and structural life predictions from a sparse multi-sensor data acquisition system can be a challenging task. This paper discusses the evaluation of physics-based versus machine-learning algorithms for predicting loads and structural life at mission critical locations on the spacecraft structure using a finite element loads analysis with the application of simulated noise and noise reduction techniques. To estimate the loads from accelerations, the physics-based algorithm leverages a loads transformation matrix from a Craig-Bampton reduced finite element model. A System Equivalent Reduction Expansion Process (SEREP) and a pseudo-inverse approach are considered to expand from the onboard sensor degrees of freedom to the Craig-Bampton model degrees of freedom. The machine learning algorithm provides a data driven solution/mapping of the sensor accelerations to the loads at the mission critical locations using a high dimensionality analysis. Although these strategies produce comparable loads prediction without noise, the limitations of these strategies with incorporating simulated noise and noise reduction techniques with low signal to noise ratio signals are evaluated. The study demonstrates the immense potential of statistical learning algorithms for sparse structural prognostic models and enhancing signal denoising techniques. These findings also highlight the need for noise-resilient prognostic models and low-noise data acquisition systems onboard spacecraft structures.

Spacecraft Structural Health Monitoring↗

NASA NTRS1994

Analysis of new composite architectures

Global/local method in conjunction with a special macro finite element is used to gain computational efficiency in the simulation of textile composites behavior. Results are included to demonstrate the effectiveness of the method. Also, 2D finite elements are used to study boundary effects in plain weave composite specimens subjected to extension, shear, and flexure loads. Effective extension, shear, and flexural moduli were found to be quite sensitive to specimen size. For extension and flexure loads stress distributions were affected by a free surface, but the free surface boundary effect did not appear to propagate very far into the interior. For shear load, the boundary effect appeared to propagate much further into the interior. The report is in the form of two technical articles, the first describes the global/local method while the second describes the use of the 2D finite elements.

Whitcomb, John D.↗

NASA NTRS2007

A Statistical Approach for the Concurrent Coupling of Molecular Dynamics and Finite Element Methods

Molecular dynamics (MD) methods are opening new opportunities for simulating the fundamental processes of material behavior at the atomistic level. However, increasing the size of the MD domain quickly presents intractable computational demands. A robust approach to surmount this computational limitation has been to unite continuum modeling procedures such as the finite element method (FEM) with MD analyses thereby reducing the region of atomic scale refinement. The challenging problem is to seamlessly connect the two inherently different simulation techniques at their interface. In the present work, a new approach to MD-FEM coupling is developed based on a restatement of the typical boundary value problem used to define a coupled domain. The method uses statistical averaging of the atomistic MD domain to provide displacement interface boundary conditions to the surrounding continuum FEM region, which, in return, generates interface reaction forces applied as piecewise constant traction boundary conditions to the MD domain. The two systems are computationally disconnected and communicate only through a continuous update of their boundary conditions. With the use of statistical averages of the atomistic quantities to couple the two computational schemes, the developed approach is referred to as an embedded statistical coupling method (ESCM) as opposed to a direct coupling method where interface atoms and FEM nodes are individually related. The methodology is inherently applicable to three-dimensional domains, avoids discretization of the continuum model down to atomic scales, and permits arbitrary temperatures to be applied.

Saether, E.↗

NASA NTRS1979

Solution of a few nonlinear problems in aerodynamics by the finite elements and functional least squares methods

The numerical simulation of the transonic flows of idealized fluids and of incompressible viscous fluids, by the nonlinear least squares methods is presented. The nonlinear equations, the boundary conditions, and the various constraints controlling the two types of flow are described. The standard iterative methods for solving a quasi elliptical nonlinear equation with partial derivatives are reviewed with emphasis placed on two examples: the fixed point method applied to the Gelder functional in the case of compressible subsonic flows and the Newton method used in the technique of decomposition of the lifting potential. The new abstract least squares method is discussed. It consists of substituting the nonlinear equation by a problem of minimization in a H to the minus 1 type Sobolev functional space.

Periaux, J.↗

NASA NTRS1995

Simulation of thin slot spirals and dual circular patch antennas using the finite element method with mixed elements

This semi-annual report describes progress up to mid-January 1995. The report contains five sections all dealing with the modeling of spiral and patch antennas recessed in metallic platforms. Of significance is the development of decomposition schemes which separate the different regions of the antenna volume. Substantial effort was devoted to improving the feed model in the context of the finite element method (FEM). Finally, an innovative scheme for truncating finite element meshes is presented.

Gong, Jian↗

NASA NTRS2010

Assessment of Static Delamination Propagation Capabilities in Commercial Finite Element Codes Using Benchmark Analysis

With capabilities for simulating delamination growth in composite materials becoming available, the need for benchmarking and assessing these capabilities is critical. In this study, benchmark analyses were performed to assess the delamination propagation simulation capabilities of the VCCT implementations in Marc TM and MD NastranTM. Benchmark delamination growth results for Double Cantilever Beam, Single Leg Bending and End Notched Flexure specimens were generated using a numerical approach. This numerical approach was developed previously, and involves comparing results from a series of analyses at different delamination lengths to a single analysis with automatic crack propagation. Specimens were analyzed with three-dimensional and two-dimensional models, and compared with previous analyses using Abaqus . The results demonstrated that the VCCT implementation in Marc TM and MD Nastran(TradeMark) was capable of accurately replicating the benchmark delamination growth results and that the use of the numerical benchmarks offers advantages over benchmarking using experimental and analytical results.

Orifici, Adrian C.↗

NASA NTRS2016

Tangle-Free Finite Element Mesh Motion for Ablation Problems

In numerical simulations involving boundaries that evolve in time, the primary challenge is updating the computational mesh to reflect the physical changes in the domain. In particular, the fundamental objective for any such \mesh motion" scheme is to maintain mesh quality and suppress unphysical geometric anamolies and artifacts. External to a physical process of interest, mesh motion is an added component that determines the specifics of how to move the mesh given certain limited information from the main system. This paper develops a set of boundary conditions designed to eliminate tangling and internal collision within the context of PDE-based mesh motion (linear elasticity). These boundary conditions are developed for two- and three-dimensional meshes. The paper presents detailed algorithms for commonly occuring topological scenarios and explains how to apply them appropriately. Notably, the techniques discussed herein make use of none of the specifics of any particular formulation of mesh motion and thus are more broadly applicable. The two-dimensional algorithms are validated by an extensive verification procedure. Finally, many examples of diverse geometries in both two- and three-dimensions are shown to showcase the capabilities of the tangle-free boundary conditions.

Droba, Justin↗

NASA NTRS2016

Crash Testing and Simulation of a Cessna 172 Aircraft: Pitch Down Impact Onto Soft Soil

During the summer of 2015, NASA Langley Research Center conducted three full-scale crash tests of Cessna 172 (C-172) aircraft at the NASA Langley Landing and Impact Research (LandIR) Facility. The first test represented a flare-to-stall emergency or hard landing onto a rigid surface. The second test, which is the focus of this paper, represented a controlled-flight-into-terrain (CFIT) with a nose-down pitch attitude of the aircraft, which impacted onto soft soil. The third test, also conducted onto soil, represented a CFIT with a nose-up pitch attitude of the aircraft, which resulted in a tail strike condition. These three crash tests were performed for the purpose of evaluating the performance of Emergency Locator Transmitters (ELTs) and to generate impact test data for model validation. LS-DYNA finite element models were generated to simulate the three test conditions. This paper describes the model development and presents test-analysis comparisons of acceleration and velocity time-histories, as well as a comparison of the time sequence of events for Test 2 onto soft soil.

Fasanella, Edwin L.↗

NASA NTRS1998

Numerical Modeling of Solidification in Space With MEPHISTO-4

A pre-flight analysis of the directional solidification of BiSn with MEPHISTO-4 is presented. Simplified Bridgman growth under microgravity conditions is simulated using a two dimensional finite element model. This numerical model is a single domain, pseudo-steady state model, and includes the effects of both thermal and solutal convection. The results show that for all orientations of the applied steady state gravity vector, of magnitude 1 micro-g, the directional solidification process remains diffusion controlled. The maximum convective velocity was found to be 4.424 x 10(exp -5) cm/s for the horizontal Bridgman growth configuration. This value is an order of magnitude lower than the growth velocity. The maximum and minimum values or solute concentration in the liquid at the crystal-melt interface were 13.867 at.% and 13.722 at.%, respectively. This gives a radial segregation value of xi = 1.046% at the interface. A secondary objective of this work was to compare the results obtained to those that consider thermal convection only (no solutal convection). It was found that the convective flow patterns in simulations which included solutal convection were significantly different from those which ignored solutal convection. The level of radial segregation predicted by the current simulations is an order of magnitude lower than that found in simulations which ignore solutal convection. The final aim was to investigate the effect of g-jitter on the crystal growth process. A simulation was performed to calculate the system response to a 1 second, 100 micro-g gravity impulse acting normal to the direction of growth. This pulse is consistent with that induced by Orbiter thruster firings. The results obtained indicate that such a gravity pulse causes an increase in the level of radial solute segregation at the interface from the steady state values. The maximum value of solute concentration in the liquid was found to be 13.888 at.%, the minimum value calculated was 13.706 at.%, yielding a radial segregation value of xi = 1.31% at the interface. These values occurred 126 seconds after the pulse terminated. Thus it is anticipated that the process will remain diffusion controlled even when subjected to such g-jitter.

Simpson, James E.↗

NASA NTRSDate not supplied

A Workflow to Rapidly Interrogate Multiscale Model Simulation Results Across Multiple Length Scales

Many tools can be used to visualize field and state variables for a single scale analysis so that the influence of relevant mechanisms can be evaluated. Finite element software is often utilized to simulate a unit cell of a material and visualize results at that scale. Material properties can be homogenized from individual constituents and local deformation, damage, and failure mechanisms can be evaluated within the unit cell due to globally applied boundary conditions. Such solutions can produce satisfactory results if a user is only interested in analyzing a single scale. But materials in general contain features across multiple length scales, and assumptions must be made when attempting to account for lower length scale phenomena within a higher length scale model. Multiscale modeling is an attractive means to model materials because detailed material responses can be tracked across multiple disparate length scales while reducing the amount of required assumptions. However, as the complexity of these models increases, a large amount of data can be produced, and data traceability can become increasingly more difficult. Field and state variables, which are naturally dependent on spatial position, may themselves be calculated from one or more lower length scale unit cell models each with their own appropriate field and state variables. The NASA Multiscale Analysis Tool (NASMAT) is one software that can be used to perform a multiscale analysis efficiently and output requested data at all length scales in the analysis. A companion open-source Python software, NASMAT PrePost, can be used to visualize NASMAT model results and rapidly interrogate multiscale data across multiple length scales. This presentation will demonstrate some of the key features of NASMAT PrePost on two multiscale problems by quickly displaying and demonstrating connectivity among multiscale results from large datasets.

Python↗

NASA NTRSDate not supplied

Study of Aircraft Structural Response and Occupant Loading During a Ditching Event Utilizing LS-DYNA Simulation

In this study, the capability of finite element model (FEM) analysis to assess aircraft structural response and occupant injury risk during aircraft water ditching conditions was evaluated. A FEM of the Fokker F28 aircraft, previously validated against full-scale crash test data, was simulated in a realistic water impact environment utilizing recorded conditions from the ditching of US Airways Flight 1549 into the Hudson River. The FEM of the F28 aircraft, was developed from a NASTRAN loads model provided by the vehicle manufacturer, calibrated using component fuselage drop-tests, and validated through test-analysis comparisons from a full-scale crash test of the F28 onto soil. Simulation results are presented in several categories: vehicle kinematics, structural accelerations, damage, occupant responses, and injury risk predictions. Results were consistent with the general outcomes of Flight 1549, indicating that the developed vehicle FEM, validated against land impact test data, may provide an effective tool for evaluating water ditching events.

Jacob Putnam↗

NASA NTRS1989

A NASTRAN/TREETOPS solution to a flexible, multi-body dynamics and controls problem on a UNIX workstation

Demands for nonlinear time history simulations of large, flexible multibody dynamic systems has created a need for efficient interfaces between finite-element modeling programs and time-history simulations. One such interface, TREEFLX, an interface between NASTRAN and TREETOPS, a nonlinear dynamics and controls time history simulation for multibody structures, is presented and demonstrated via example using the proposed Space Station Mobile Remote Manipulator System (MRMS). The ability to run all three programs (NASTRAN, TREEFLX and TREETOPS), in addition to other programs used for controller design and model reduction (such as DMATLAB and TREESEL, both described), under a UNIX Workstation environment demonstrates the flexibility engineers now have in designing, developing and testing control systems for dynamically complex systems.

Benavente, Javier E.↗

NASA NTRS1992

Computational simulation of intermingled-fiber hybrid composite behavior

Three-dimensional finite-element analysis and a micromechanics based computer code ICAN (Integrated Composite Analyzer) are used to predict the composite properties and microstresses of a unidirectional graphite/epoxy primary composite with varying percentages of S-glass fibers used as hydridizing fibers at a total fiber volume of 0.54. The three-dimensional finite-element model used in the analyses consists of a group of nine fibers, all unidirectional, in a three-by-three unit cell array. There is generally good agreement between the composite properties and microstresses obtained from both methods. The results indicate that the finite-element methods and the micromechanics equations embedded in the ICAN computer code can be used to obtain the properties of intermingled fiber hybrid composites needed for the analysis/design of hybrid composite structures. However, the finite-element model should be big enough to be able to simulate the conditions assumed in the micromechanics equations.

Mital, Subodh K.↗

NASA NTRS2016

Stochastic-Strength-Based Damage Simulation of Ceramic Matrix Composite Laminates

The Finite Element Analysis-Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program was used to characterize and predict the progressive damage response of silicon-carbide-fiber-reinforced reaction-bonded silicon nitride matrix (SiC/RBSN) composite laminate tensile specimens. Studied were unidirectional laminates [0] (sub 8), [10] (sub 8), [45] (sub 8), and [90] (sub 8); cross-ply laminates [0 (sub 2) divided by 90 (sub 2),]s; angled-ply laminates [plus 45 (sub 2) divided by -45 (sub 2), ]s; doubled-edge-notched [0] (sub 8), laminates; and central-hole laminates. Results correlated well with the experimental data. This work was performed as a validation and benchmarking exercise of the FEAMAC/CARES program. FEAMAC/CARES simulates stochastic-based discrete-event progressive damage of ceramic matrix composite and polymer matrix composite material structures. It couples three software programs: (1) the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC), (2) the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program (CARES/Life), and (3) the Abaqus finite element analysis program. MAC/GMC contributes multiscale modeling capabilities and micromechanics relations to determine stresses and deformations at the microscale of the composite material repeating-unit-cell (RUC). CARES/Life contributes statistical multiaxial failure criteria that can be applied to the individual brittle-material constituents of the RUC, and Abaqus is used to model the overall composite structure. For each FEAMAC/CARES simulation trial, the stochastic nature of brittle material strength results in random, discrete damage events that incrementally progress until ultimate structural failure.

composite structures↗

NASA NTRS2004

Higher-Order Finite Elements for Computing Thermal Radiation

Two variants of the finite-element method have been developed for use in computational simulations of radiative transfers of heat among diffuse gray surfaces. Both variants involve the use of higher-order finite elements, across which temperatures and radiative quantities are assumed to vary according to certain approximations. In this and other applications, higher-order finite elements are used to increase (relative to classical finite elements, which are assumed to be isothermal) the accuracies of final numerical results without having to refine computational meshes excessively and thereby incur excessive computation times. One of the variants is termed the radiation sub-element (RSE) method, which, itself, is subject to a number of variations. This is the simplest and most straightforward approach to representation of spatially variable surface radiation. Any computer code that, heretofore, could model surface-to-surface radiation can incorporate the RSE method without major modifications. In the basic form of the RSE method, each finite element selected for use in computing radiative heat transfer is considered to be a parent element and is divided into sub-elements for the purpose of solving the surface-to-surface radiation-exchange problem. The sub-elements are then treated as classical finite elements; that is, they are assumed to be isothermal, and their view factors and absorbed heat fluxes are calculated accordingly. The heat fluxes absorbed by the sub-elements are then transferred back to the parent element to obtain a radiative heat flux that varies spatially across the parent element. Variants of the RSE method involve the use of polynomials to interpolate and/or extrapolate to approximate spatial variations of physical quantities. The other variant of the finite-element method is termed the integration method (IM). Unlike in the RSE methods, the parent finite elements are not subdivided into smaller elements, and neither isothermality nor other unrealistic physical conditions are assumed. Instead, the equations of radiative heat transfer are integrated numerically over the parent finite elements by use of a computationally efficient Gaussian integration scheme.

Gould, Dana C.↗

NASA NTRS1990

The semidiscrete Galerkin finite element modeling of compressible viscous flow past an airfoil

The primary project was the numerical simulation, by a finite element/finite difference method, of the viscous flow about an airfoil. The secondary project involved the numerical simulation of the three-dimensional separated and vortex-dominated flow about a hemispherically capped cylinder in the transonic regime. Preliminary calculations were started for the hemisphere-cylinder at 0 and 5 degree angle of attack. The solution of the flow field about airfoils and wings is required to determine the important parameters of lift, moment, and drag. Viscous effects must be accounted for if the drag is to be accurately calculated. At present there are basically two approaches to the numerical simulation of the flow field, the use of fully viscous models and the inviscid/viscous models. The fully viscous models require the solution of an approximation of the Navier-Stokes equations and therefore should simulate most of the physical mechanisms. A fast, accurate, and computationally efficient inviscid flow solver was recently developed by Hartwich. It is thought that Hartwich's program coupled to a fast, accurate, and computationally efficient boundary layer code, will make an excellent tool for airfoil design. The purpose of the primary project was to develop a compressible boundary layer code using the semidiscrete Galerkin finite element method. The numerical scheme employed used the combination of a Dorodnitsyn formulation of the boundary layer equations, with a finite difference/finite element procedure (semidiscrete Galerkin method), in the solution of the compressible two-dimensional boundary layer equations. A laminar compressible boundary layer code was developed and tested for a NACA 0012 airfoil at a Mach number of 0.5, a Reynolds number of 5000, and zero angle of attack. At present the boundary layer program solves up to, but not beyond, separation.

Meade, Andrew J.↗