Search NASA⌕ Search

SEARCH · Search NASA

Results for “Form factors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Comparing the Performance of Hyperbolic and Circular Rod Quadrupole Mass Spectrometers with Applied Higher Order Auxiliary Excitation

This work applies higher order auxiliary excitation techniques to two types of quadrupole mass spectrometers (QMSs): commercial systems and spaceborne instruments. The operational settings of a circular rod geometry commercial system and an engineering test-bed for a hyperbolic rod geometry spaceborne instrument were matched, with the relative performance of each sensor characterized with and without applied excitation using isotopic measurements of Kr+. Each instrument was operated at the limit of the test electronics to determine the effect of auxiliary excitation on extending instrument capabilities. For the circular rod sensor, with applied excitation, a doubling of the mass resolution at 1% of peak transmission resulted from the elimination of the low-mass side peak tail typical of such rod geometries. The mass peak stability and ion rejection efficiency were also increased by factors of 2 and 10, respectively, with voltage scan lines passing through the center of stability islands formed from auxiliary excitation. Auxiliary excitation also resulted in factors of 6 and 2 in peak stability and ion rejection efficiency, respectively, for the hyperbolic rod sensor. These results not only have significant implications for the use of circular rod quadrupoles with applied excitation as a suitable replacement for traditional hyperbolic rod sensors, but also for extending the capabilities of existing hyperbolic rod QMSs for the next generation of spaceborne instruments and low-mass commercial systems.

Gershman, D. J.↗

Comparing the Performance of Hyperbolic and Circular Rod Quadrupole Mass Spectrometers with Applied Higher Order Auxiliary Excitation

This work applies higher order auxiliary excitation techniques to two types of quadrupole mass spectrometers (QMSs): commercial systems and spaceborne instruments. The operational settings of a circular rod geometry commercial system and an engineering test-bed for a hyperbolic rod geometry spaceborne instrument were matched, with the relative performance of each sensor characterized with and without applied excitation using isotopic measurements of Kr+. Each instrument was operated at the limit of the test electronics to determine the effect of auxiliary excitation on extending instrument capabilities. For the circular rod sensor, with applied excitation, a doubling of the mass resolution at 1% of peak transmission resulted from the elimination of the low-mass side peak tail typical of such rod geometries. The mass peak stability and ion rejection efficiency were also increased by factors of 2 and 10, respectively, with voltage scan lines passing through the center of stability islands formed from auxiliary excitation. Auxiliary excitation also resulted in factors of 6 and 2 in peak stability and ion rejection efficiency, respectively, for the hyperbolic rod sensor. These results not only have significant implications for the use of circular rod quadrupoles with applied excitation as a suitable replacement for traditional hyperbolic rod sensors, but also for extending the capabilities of existing hyperbolic rod QMSs for the next generation of spaceborne instruments and low-mass commercial systems.

auxiliary excitation↗

Precision Fe K-Alpha and Fe K-Beta Line Spectroscopy of the Seyfert 1.9 Galaxy NGC 2992 with Suzaku

We present detailed time-averaged X-ray spectroscopy in the 0.5-10 keV band of the Seyfert 1.9 galaxy NGC 2992 with the Suzaku X-ray Imaging Spectrometers (XIS). The source had a factor approximately 3 higher 2-10 keV flux (approximately 1.2 x l0(exp -11) erg per square cm per s) than the historical minimum and a factor approximately 7 less than the historical maximum. The XIS spectrum of NGC 2992 can be described by several components. There is a primary continuum, modeled as a power-law with a photon index of Gamma = 1.57(sup +0.06) (sup -0.03) that is obscured by a Compton-thin absorber with a column density of 8.01(sup +0.6) (sup -0.5)x l0 (exp 21) per square cm. . There is another, weaker, unabsorbed power-law component (modeled with the same slope as the primary), that is likely to be due to the primary continuum being electron-scattered into our line-of-sight by a region extended on a scale of hundreds of parsecs. We measure the Thomson depth of the scattering zone to be Tau = 0.072 +/- 0.021. An optically-thin thermal continuum emission component, which probably originates in the same extended region, is included in the model and yields a temperature and luminosity of KT = 0.656(sup +0.088) (sup -0.0.61) keV and approximately 1.2 +/- 0.4 x l0 (exp 40) erg per s respectively. We detect an Fe K emission complex which we model with broad and narrow lines and we show that the intensities of the two components are decoupled at a confidence level > 3 sigma. The broad Fe K alpha line has an equivalent width of 118(sup +32) (sup -61) eV and could originate in an accretion disk (with inclination angle greater than approximately 30 deg) around the putative central black hole. The narrow Fe K alpha line has an equivalent width of 1632(sup +47) (sup -26) eV and is unresolved (FWHM < 4630 km per s) and likely originates in distant matter. The absolute flux in the narrow line implies that the column density out of the line-of-sight could be much higher than measured in the line-of-sight, and that the mean (historically-averaged) continuum luminosity responsible for forming the line could be a factor of several higher than that measured from the data. We also detect the Fe K Beta line (corresponding to the narrow Fe K alpha line) with a high signal-to-noise ratio and describe a new robust method to constrain the ionization state of Fe responsible for the Fe K alpha and Fe K Beta lines that does not require any knowledge of possible gravitational and Doppler energy shifts affecting the line energies. For the distant line-emitting matter (e. g. the putative obscuring torus) we deduce that the predominant ionization state is lower than Fe VIII (at 99% confidence), conservatively taking into account residual calibration uncertainties in the XIS energy scale and theoretical and experimental uncertainties in the Fe K fluorescent line energies. From the limits on a possible Compton-reflection continuum it is likely that the narrow Fe K alpha and Fe K Beta lines originate in a Compton-thin structure.

Yaqoob, Tahir↗

The effects of bandpass limiters on n-phase tracking systems

The combination of a bandpass limiter and an n-th power tracking loop is considered. Performance of the combination does not depend on the form of the nonlinear function used to create the n-th harmonic signal as long as some energy in that zone is produced. The order in which the limiter and n-th power nonlinearity occur is unimportant so that the results apply equally well to the n-phase Costas type of implementations of the n-th power loops. Closed form expressions for the signal suppression factors are obtained. Coherent and noncoherent SNR's out of the n-th power-limiter combination can be expressed in terms of two of these suppression factors. The loop SNR of an n-th power-limited phase locked loop is estimated by simply calculating the suppression factors for n-th and 2n-th power loops. Finally, n-th power phase locked loops without limiters are compared with similar loops with limiters; the limiter can actually enhance output SNR at moderate to large input SNR.

Butman, S. A.↗

The effects of bandpass limiters on n-phase tracking systems

The combination of a bandpass limiter and an n(th) power tracking loop is considered. It is shown that the performance of the combination does not depend on the form of the nonlinear function used to create the n(th) harmonic signal so long as some energy in that zone is produced. Furthermore, the order in which the limiter and n(th) power nonlinearity occur is unimportant so that the results apply equally well to the n-phase Costas type of implementation of the n(th) power loops. Closed form expressions for the signal suppression factors are obtained and it is shown that the coherent and noncoherent SNR's out of the n(th) power-limiter combination can be expressed in terms of two of these suppression factors. This later point enables one to estimate the loop SNR of an n(th) power-limiter phase locked loop by simply calculating the suppression factors for n(th) and 2n(th) power loops. Finally, n(th) power phase locked loops without limiters are compared with similar loops with limiters where it is shown that the presence of the limiter can actually enhance the output SNR at moderate to large values of input SNR.

Butman, S. A.↗

A two-dimensional thermal analysis of a new high-performance tubular solar collector

The first of two articles are presented which describe and analyze the thermal performance of a vacuum tube solar collector. The assumptions and mathematical modeling are presented. The problem is reduced to the formulation of two simultaneous linear differential equations characterizing the collector thermal behavior. After applying the boundary conditions, a general solution is obtained which is found similar to the general Hottel, Whillier and Bliss form but with a complex flow factor.

Lansing, F. L.↗

A computer-aided design system geared toward conceptual design in a research environment

A computer-aided design system has recently been developed specifically for the small research group environment. The system is implemented on a Prime 400 minicomputer linked with a CDC 6600 computer. The goal was to assign the minicomputer specific tasks, such as data input and graphics, thereby reserving the large mainframe computer for time-consuming analysis codes. The basic structure of the design system consists of GEMPAK, a computer code that generates detailed configuration geometry from a minimum of input; interface programs that reformat GEMPAK geometry for input to the analysis codes; and utility programs that simplify computer access and data interpretation. The working system has had a large positive impact on the quantity and quality of research performed by the originating group. This paper describes the system, the major factors that contributed to its particular form, and presents examples of its application.

STACK S. H.↗

Analysis of a high-performance tubular solar collector

This article analyzes the thermal performance of a new vacuum tube solar collector. The assumptions and mathematical modeling are presented. The problem is reduced to the formulation of two simultaneous linear differential equations characterizing the collector thermal behavior. After applying the boundary conditions, a general solution is obtained which is found similar to the general Hottel, Whillier and Bliss form, but with a complex flow factor. The details of the two-dimensional thermal model of the solar collector at steady state is also presented to include the computer simulation and the performance parameterization. Comparison of the simulated performance with the manufacturer's test data showed good agreement at wide ranges of operating conditions.

Lansing, F. L.↗

A standard description and costing methodology for the balance-of-plant items of a solar thermal electric power plant. Report of a multi-institutional working group

Standard descriptions for solar thermal power plants are established and uniform costing methodologies for nondevelopmental balance of plant (BOP) items are developed. The descriptions and methodologies developed are applicable to the major systems. These systems include the central receiver, parabolic dish, parabolic trough, hemispherical bowl, and solar pond. The standard plant is defined in terms of four categories comprising (1) solar energy collection, (2) power conversion, (3) energy storage, and (4) balance of plant. Each of these categories is described in terms of the type and function of components and/or subsystems within the category. A detailed description is given for the BOP category. BOP contains a number of nondevelopmental items that are common to all solar thermal systems. A standard methodology for determining the costs of these nondevelopmental BOP items is given. The methodology is presented in the form of cost equations involving cost factors such as unit costs. A set of baseline values for the normalized cost factors is also given.

Source record↗

A Residuals Approach to Filtering, Smoothing and Identification for Static Distributed Systems

An approach for state estimation and identification of spatially distributed parameters embedded in static distributed (elliptic) system models is advanced. The method of maximum likelihood is used to find parameter values that maximize a likelihood functional for the system model, or equivalently, that minimize the negative logarithm of this functional. To find the minimum, a Newton-Raphson search is conducted that from an initial estimate generates a convergent sequence of parameter estimates. For simplicity, a Gauss-Markov approach is used to approximate the Hessian in terms of products of first derivatives. The gradient and approximate Hessian are computed by first arranging the negative log likelihood functional into a form based on the square root factorization of the predicted covariance of the measurement process. The resulting data processing approach, referred to here by the new term of predicted data covariance square root filtering, makes the gradient and approximate Hessian calculations very simple. A closely related set of state estimates is also produced by the maximum likelihood method: smoothed estimates that are optimal in a conditional mean sense and filtered estimates that emerge from the predicted data covariance square root filter.

Rodriguez, G.↗

Numerical algorithms for finite element computations on concurrent processors

The work of several graduate students which relate to the NASA grant is briefly summarized. One student has worked on a detailed analysis of the so-called ijk forms of Gaussian elemination and Cholesky factorization on concurrent processors. Another student has worked on the vectorization of the incomplete Cholesky conjugate method on the CYBER 205. Two more students implemented various versions of Gaussian elimination and Cholesky factorization on the FLEX/32.

Ortega, J. M.↗

Software development without languages

Automatic programming generally involves the construction of a formal specification; i.e., one which allows unambiguous interpretation by tools for the subsequent production of the corresponding software. Previous practical efforts in this direction have focused on the serious problems of: (1) designing the optimum specification language; and (2) mapping (translating or compiling) from this specification language to the program itself. The approach proposed bypasses the above problems. It postulates that the specification proper should be an intermediate form, with the sole function of containing information sufficient to facilitate construction of programs and also of matching documentation. Thus, the means of forming the intermediary becomes a human factors task rather than a linguistic one; human users will read documents generated from the specification, rather than the specification itself.

Osborne, Haywood S.↗

Low thrust viscous nozzle flow field predictions

The low thrust viscous nozzle flows have been studied numerically by using the steady-state Reynolds-averaged Navier-Stokes equations in conservative form. A new Lower-Upper factorization scheme in the axisymmetric coordinate system has been developed and is analyzed in this paper. This new Navier-Stokes solver has shown that the numerical analog is accurate and stable for the convergent and divergent nozzle flowfield calculation. The range of the chamber pressure is (1.85-29.4)psi with the chamber temperature equal to 600 F. The results are compared with the data collected in the NASA/MSFC vacuum chamber, and they are in very reasonable agreement.

Chou, L. C.↗

A study of flying-boat take-off

It is shown that the normal resistance curve for a flying boat may be approximated by two straight lines. The equations for take-off distance and time, derived from this approximation, are applied to a series of flying boats and the resulting factors are plotted in non dimensional form in a series of charts. Take-off performances from the charts are shown to be in good agreement with step-by-step integrations. Some applications of the charts to the solution of general design problems are included.

Diehl, Walter S↗

Experimental research on air propellers

The purposes of the experimental investigation on the performance of air propellers described in this report are as follows: (1) the development of a series of design factors and coefficients drawn from model forms distributed with some regularity over the field of air-propeller design and intended to furnish a basis of check with similar work done in other aerodynamic laboratories, and as a point of departure for the further study of special or individual types and forms; (2) the establishment of a series of experimental values derived from models and intended for later use as a basis for comparison with similar results drawn from certain selected full-sized forms and tested in free flight.

Durand, William F↗

Performance of rotating-wing aircraft

Up to the present there has been no coordinated presentation from which the influence of the constants essential for the performance of rotating-wing aircraft could be obtained in a systematic manner. The attempt at such a survey is made in the following, whereby nonessential factors, such as effect of blade form, blade profile, blade number, and blade twist on the performances are disregarded. Even the torsional flexibility of the blades is overlooked.

Hohenemser, K↗

Stellar coronal abundances. 3: The solar first ionization potential effect determined from full-disk observation

In this paper we reanalayze the full-disk quiet-sun spectrum of Mallinovsky & Heroux (1973) with modern atomic data. The purposes of this are to check our atomic data and methods in other investigations using data from nearby stars obtained with the NASA Extreme Ultraviolet Explorer (EUVE) satellite, and to confirm that the solar first ionization potential (FIP) effect investigated by previous authors studying discrete solar regions is the same as that found in full-disk spectra. We recover the usual solar FIP effect of a coronal abundance enhancement of elements with a low FIP of a factor approximately 3-4 for lines formed at temperatures greater than approximately 10(exp 6) K. For lower temperatures, the FIP effect seems to be substantially smaller, in qualitative agreement with other data. Comparing our full-disk result with those from discrete solar structures suggest that the FIP effect is a function of altitude, with the lower temperature full-disk emission being dominated by the super-granulation network. We also compare the recent ionization balance of Arnaud & Raymond (1992) with that of Arnaud & Rothenflug (1985).

Laming, J. Martin↗

HIRES Dust Imaging of the NGC 6334 Star Forming Complex

We present here our final report for the NASA grant "HIRES Dust Imaging of the NGC 6334 Star Forming Complex." This project was designed to study the photodissociation regions surrounding several OB stars in this cloud complex. NGC 6334 is unique in having at least seven distinct massive star forming regions in the same molecular cloud complex. The obvious advantage of studying young stars in the same molecular complex is that the stars all formed in the same global environment. Consequently, global factors like density waves, abundances, global magnetic field strength, and age of the parental molecular cloud cannot contribute to the differences among the star forming regions. Instead, the differences must arise only from local effects such as the mass, age, and UV fields of the individual stars. A study of NGC 6334 will greatly simplify the general problem of comparing different star formation regions by eliminating global effects.

Jackson, James M.↗