Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Experimental investigation of injection-induced fracturing during supercritical CO 2 sequestration

Leakage risk assessment is an inevitable procedure in permanent sequestration and storage of CO 2 in deep saline aquifers and depleted oil and gas reservoirs, where the integrity of caprock is most critical. Here, low porosity and low permeability concrete cubes were employed as caprock analogs to investigate the supercritical CO 2 injection-induced fracturing processes under true tri-axial stress conditions. A systematic experimental procedure, consisting of active acoustic emission measurement, pressure decay, injection pressure and temperature monitoring, fracture coloring, and gas fracturing, is formulated to qualitatively and quantitatively characterize the injection-induced fracturing processes and fracture morphology. Occurrence of injection-induced fracturing can be directly identified from peaks of borehole pressure profiles as well as sharp drops on temperature profiles due to CO 2 expansion, but generally there was no fracture propagation plateau appearing for the 20 cm rock cubes with zero pore pressure. Acoustic wave signatures, including both waveform change and arrival time delay, can effectively capture the extension of induced fractures inside the opaque rock. Initiation and propagation of supercritical CO 2 injection-induced fractures are highly dominated by the tri-axial stresses, following the general trend of continuum mechanics at high stress levels with large stress difference. As the stress difference decreases, induced fractures branch off in relatively arbitrary directions. For these supercritical CO 2 injection-induced fracturing experiments, poroelastic mechanics model makes a decent fit with the measured breakdown pressure of the caprock analogs. Findings in this study are valuable for risk analysis and operation optimization of geological CO 2 sequestration and storage as well as for CO 2 fracturing design and implementation in shale and tight reservoirs.

42 ENGINEERING↗

A study of changes in deep fractured rock permeability due to coupled hydro-mechanical effects

This paper presents a numerical study of the hydro-mechanical behaviour of a fractured rock domain at 1000. m depth below the land surface as a function of different levels of fluid pore pressure. A 2D fractured rock domain is adopted based on data obtained from outcrop mapping, displaying multiple fracture sets, fracture intersections, dead-end and curved fractures. A continuum based numerical model is used to evaluate the effects of compressive boundary stresses, cracking by tension failure in the intact rock and fractures and shear displacement along fractures on its equivalent permeability. Two in situ stress boundary conditions are considered: an isotropic case SR1 with the two horizontal boundary compressive stresses having the same magnitude, and an anisotropic case SR2 with the ratio between these compressive stress components set to be 2. In the SR2 case, changes in the local stress and stress ratio distributions due to different fluid pore pressure levels are anisotropic and more significant than in the SR1 case, because of tension failures in the intact rock forming bridges between fractures. These failure regions opened new flow connections between fractures and thereby caused important anisotropic changes in the flow paths, and significant decrease in local gradients of fluid pore pressure. The equivalent permeability increases sharply when the fluid pore pressure is approximately 90% of the magnitude of the minimum stress at the boundaries of the fractured rock domain. Results show that the equivalent permeability of the fractured rock domain is most sensitive to the fractures normal stiffness, the permeability of the tension failure regions and the power-law exponent for permeability change.

58 GEOSCIENCES↗

Bone Fractures Following External Beam Radiotherapy and Limb-Preservation Surgery for Lower Extremity Soft Tissue Sarcoma: Relationship to Irradiated Bone Length, Volume, Tumor Location and Dose

Purpose: To examine the relationship between tumor location, bone dose, and irradiated bone length on the development of radiation-induced fractures for lower extremity soft tissue sarcoma (LE-STS) patients treated with limb-sparing surgery and radiotherapy (RT). Methods and Materials: Of 691 LE-STS patients treated from 1989 to 2005, 31 patients developed radiation-induced fractures. Analysis was limited to 21 fracture patients (24 fractures) who were matched based on tumor size and location, age, beam arrangement, and mean total cumulative RT dose to a random sample of 53 nonfracture patients and compared for fracture risk factors. Mean dose to bone, RT field size (FS), maximum dose to a 2-cc volume of bone, and volume of bone irradiated to >=40 Gy (V40) were compared. Fracture site dose was determined by comparing radiographic images and surgical reports to fracture location on the dose distribution. Results: For fracture patients, mean dose to bone was 45 +- 8 Gy (mean dose at fracture site 59 +- 7 Gy), mean FS was 37 +- 8 cm, maximum dose was 64 +- 7 Gy, and V40 was 76 +- 17%, compared with 37 +- 11 Gy, 32 +- 9 cm, 59 +- 8 Gy, and 64 +- 22% for nonfracture patients. Differences in mean, maximum dose, and V40 were statistically significant (p = 0.01, p = 0.02, p = 0.01). Leg fractures were more common above the knee joint. Conclusions: The risk of radiation-induced fracture appears to be reduced if V40 <64%. Fracture incidence was lower when the mean dose to bone was <37 Gy or maximum dose anywhere along the length of bone was <59 Gy. There was a trend toward lower mean FS for nonfracture patients.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Identification of modes of fracture in a 2618-T6 aluminum alloy using stereophotogrammetry

The identification and the development of a quantification technique of the modes of fracture in fatigue fracture surfaces of a 2618-T6 aluminum alloy were developed during this research. Fatigue tests at room and high temperature (230 Degree-Sign C) were carried out to be able to compare the microscopic fractographic features developed by this material under these testing conditions. The overall observations by scanning electron microscopy (SEM) of the fracture surfaces showed a mixture of transgranular and ductile intergranular fracture. The ductile intergranular fracture contribution appears to be more significant at room temperature than at 230 Degree-Sign C. A quantitative methodology was developed to identify and to measure the contribution of these microscopic fractographic features. The technique consisted of a combination of stereophotogrammetry and image analysis. Stereo-pairs were randomly taken along the crack paths and were then analyzed using the profile module of MeX software. The analysis involved the 3-D surface reconstruction, the trace of primary profile lines in both vertical and horizontal directions within the stereo-pair area, the measurements of the contribution of the modes of fracture in each profile, and finally, the calculation of the average contribution in each stereo-pair. The technique results confirmed a higher contribution of ductile intergranular fracture at room temperature than at 230 Degree-Sign C. Moreover, there was no indication of a direct relationship between this contribution and the strain amplitudes range applied during the fatigue testing. - Highlights: Black-Right-Pointing-Pointer Stereophotogrammetry and image analysis as a measuring tool of modes of fracture in fatigue fracture surfaces. Black-Right-Pointing-Pointer A mixture of ductile intergranular and transgranular fracture was identified at room temperature and 230 Degree-Sign C testing. Black-Right-Pointing-Pointer Development of a quantitative methodology to obtain the percentage of modes of fracture within the fracture surface.

36 MATERIALS SCIENCE↗

P-wave velocity anisotropy related to sealed fractures reactivation tracing the structural diagenesis in carbonates

Fracture properties are important in carbonate reservoir characterization, as they are responsible for a large part of the fluid transfer properties at all scales. It is especially true in tight rocks where the matrix transfer properties only slightly contribute to the fluid flow. Open fractures are known to strongly affect seismic velocities, amplitudes and anisotropy. Here, we explore the impact of fracture evolution on the geophysical signature and directional V p anisotropy of fractured carbonates through diagenesis. For that purpose, we studied a meter-scale, parallelepiped quarry block of limestone using a detailed structural and diagenetic characterization, and numerous V p measurements. The block is affected by two en-échelon fracture clusters, both being formed in opening mode (mode 1) and cemented, but only one being reactivated in shear. We compared the diagenetic evolution of the fractures, which are almost all 100% filled with successive calcite cements, with the P-wave velocities measured across this meter-scale block of carbonate, which recorded the tectonic and diagenetic changes of a South Provence sedimentary basin. We found that a directional V p anisotropy magnitude as high as 8–16% correlates with the reactivated fractures’ cluster dip angle, which is explained by the complex filling sequence and softer material present inside the fractures that have been reactivated during the basin's tectonic inversion. We show that although a late karstification phase preferentially affected these reactivated fractures, it only amplified the pre-existing anisotropy due to tectonic shear. We conclude that V p anisotropy measurements may help to identify the fracture sealing/opening processes associated with polyphased tectonic history, the anisotropy being independent of the current stress-state. Finally, this case shows that velocity anisotropies induced by fractures resulted here from a cause that is different from how these features have often been interpreted: selective reactivation of sealed fractures clusters rather than direction of currently open ones.

58 GEOSCIENCES↗

Subsurface Characterization of Hydraulic Fracture Test Site-2 (HFTS-2), Delaware Basin

Hydraulic Fracturing Test Site-2 (HFTS-2) is a field-based research experiment performed in the Wolfcamp Formation of the Permian (Delaware) Basin. This paper focuses on integration, advanced geological characterization, and 3D subsurface modeling of the comprehensive HFTS-2 dataset. The study showcases a multidisciplinary reservoir characterization approach that incorporates geology, petrophysics, geochemistry, geomechanics, microseismic, and subsurface engineering analysis. Subsurface characterization of organic-rich mudstone formations requires understanding complex hydraulic fracture network growth in relation to inherent lithology, geomechanical properties, and interaction with pre-existing natural fractures. This paper presents a characterization workflow incorporating pre- and post-stimulation subsurface data, unique to the HFTS-2 dataset. The study integrated: (1) rock properties from logs, cores, and thin sections; (2) natural and hydraulic fracture descriptions from cores and image logs; (3) local and regional stresses; (4) geomechanics; (5) microseismic; (6) fiber optic (FO) and bottomhole pressure gauge (BHPG) response; and (7) produced fluids analysis. During a stimulation treatment, creation of the stimulated rock volume (SRV) is influenced by several subsurface factors. Key contributing factors include structural context, stress conditions, lithology, facies architecture, pre-existing natural fractures, and geomechanical properties. The HFTS-2 subsurface data integration indicates that the SRV is comprised of a complex juxtaposition of hydraulic fracture swarms, as evidenced by image logs analysis, core description, and microseismic monitoring. The HFTS-2 microseismic event density was used to generate 3D heat maps that serve as a representative SRV footprint, corroborated by secondary datasets. These maps were further integrated with petrophysical and geomechanical characteristics, as well as responses from FO and BHPG, to estimate the lateral and vertical dimensions of the effective fractures. The geological characterization for the HFTS-2 dataset combined with 3D modeling for petrophysical and geomechanical properties provides a strong foundation for subsurface simulation and optimization studies. Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/1-21URTC/D011S005R001/2477501/urtec-2021-5243-ms.pdf/1 by Carol Worster on 28 February 2022 URTeC 5243 The workflow improved our understanding of HFTS-2 hydraulic fracture propagation and characteristics in relation to offset pressure depletion and interaction with pre-existing natural fractures. Analysis showed that fracture geometry varies by stage and by well, and a complex fracture network is generated with varying fracture density. The multidisciplinary workflow presented herein for integration and characterization serves as a foundation to evaluate completion efficiency and estimate areal and vertical stimulation and depletion extent for the project. Furthermore, the workflow and learnings can also be transferred to other unconventional plays.

58 GEOSCIENCES↗

Increased Rates of Hip and Spine Fractures in Astronauts are Associated with Longer Spaceflight Durations

Given the accelerated declines in bone mineral density reported in US astronauts serving on the International Space Station, there is a possibility that a prolonged exposure to spaceflight could put astronauts at increased fracture risk during subsequent planetary explorations or after return to Earth. To date, there have been no fractures in astronauts during spaceflight. Recently-reported data from a flight study suggested that intake of the bisphosphonate alendronate combined with resistive exercise (on the Advanced Resistive Exercise Device – ARED) preserved more astronauts at their preflight skeletal status after a ~6-mos spaceflight than with ARED exercise alone. However, there is low acceptance of alendronate, or the recommended zoledronic acid, to suppress in-flight bone loss largely due to concern for unintended medication side effects and a perceived absence of astronaut fractures that can be directly attributable to spaceflight exposure. Hence, a recent survey of all astronaut fractures was analyzed to assess whether the rate of postflight fractures could be associated with extended spaceflight exposures. The fracture survey was of 262 astronauts across 8433.6 person-years (PY) and grouped according to previous exposure to a “Long Duration (LD)” spaceflight (3 mos or greater, but typically 6-mos). The number of fractures was modeled using count regression adjusting for i) the repeated measures within individuals across the groups, ii) the differing length of surveillance for each individual and iii) age at start of surveillance for each of the groups. Astronaut Group by Spaceflight Exposure #Individuals PY Covered No Exposure to Spaceflight 262 1882.7 No Exposure to LD spaceflight “Non-LD” 232 6121.3 Exposure to LD spaceflight 42 429.6 Analysis revealed an increased rate of hip and spine fractures for surveillance periods compared between LD Exposure and Non-LD Exposure: Hip – Relative Rate: 3.4 (95%CI: 1.0, 12.0); Spine– Relative Rate: 3.4 (95%CI: 1.0, 11.6). For all other skeletal sites, rates of fracture were similar for LD and Non-LD exposures. Data comparisons were conducted between groups of astronauts to preclude the interpretation of greater physical activity in astronauts as a contributing factor to fracture rates. This analysis of fracture data is the first report associating postflight hip and spine fractures in astronauts with exposure to extended duration spaceflights. Further analyses integrating co-morbidities for bone loss are planned.

skeleton↗

Inferring fracture dilation and shear slip from surface deformation utilising trained surrogate models

An important task in energy and CO 2 storage (sequestration) in the subsurface is to verify that the surrounding fractures and faults are not activated, acting as leakage pathways. This is achievable through effective and efficient Measurement, Monitoring and Verification (MMV) plans. In this work, two surrogate models are trained to captures dilation (opening) and shear deformation of fractures, and the associated surface deformation. The trained surrogate model, based on conditional Generative-Adversarial Networks (cGAN) receives fracture apertures from dilational fractures together with fracture slips from shear fractures and predicts the combined surface deformation. An inversion algorithm based on Bayesian framework is proposed to identify the geometry of both types of fractures, as well as volume of dilational fractures and deformation moment induced by shear fractures, all from the measured surface deformation data. The inversion algorithm utilises the Differential Evolution (DE) optimisation technique that has the superior performance in finding the global minimum of cost function. The proposed surrogate-assisted inversion successfully inferred the unknown dip, dip direction and the volume of the dilational fractures as well as the induced deformation moment in shear fractures. The model was further tested for the inversion of a field hydraulic fracturing tilt dataset applying different scenarios with varying unknowns to show the model's performance, as well as incorporating shear deformation for better match with the observed data.

Dilation and shear↗

Integrated simulation of vertical fracture propagation induced by water injection and its borehole electromagnetic responses in shale gas systems

We analyze fracture propagation induced by hydraulic fracturing with water injection and examine their detectability with crosswell electromagnetic (EM) geophysical methods. For rigorous 3D coupled flow-geomechanical modeling, we employ a numerical method that can model failure by tensile and shear stresses, dynamic nonlinear permeability, dual continuum approach, and thermo-poro-mechanical effects. From numerical simulation, we find that the fracture propagation is not the same as propagation of the water front, because fracturing is governed by geomechanics whereas water saturation is determined by multiphase flow. At early times, the water front is almost identical to the fracture tip, suggesting that the fracture is mostly filled with the injected water. However, at late times, movement of the water front is retarded compared to fracture propagation, yielding a significant gap between the water front and the fracture top, filled with reservoir gas. During fracture propagation, the coupled flow-geomechanical models are transformed via a rock-physics model into electrical conductivity models. We employ a full 3D finite-element EM geophysical simulator to evaluate the sensitivity of the crosswell EM method to fracture propagation. It is shown that anomalous distribution of electrical conductivity is closely related to the injected water saturation, but not closely related to newly created unsaturated fractures. Our numerical modeling experiments demonstrate that the crosswell EM method can be highly sensitive to electrical conductivity changes that directly indicate the migration pathways of the injected fluid. Accordingly, the EM method can serve as an effective monitoring tool for monitoring the injected fluids during hydraulic fracturing operations.

58 GEOSCIENCES↗

Effects of hydration on fractures and shale permeability under different confining pressures: An experimental study

Water-rich fracturing fluids are injected into gas shale formations to promote the effective development of gas. However, the relationship between gas production decreases and the variability flow-back fluid behavior (rate and amount) remains a significant challenge to the industry. This study focused on the effects of water hydration on the rock fracture properties of a major gas shale formation in China. Shale from hydration experiments was characterized for a number of key parameters including length, volume, width, surface area, thickness and fracture frequency. X-ray computed tomography (CT) scanning was conducted on shale reservoir samples exposed to water at zero overburden stress and under three different confining pressures (725 psi, 2175 psi, and 2900 psi). CT scanning images were obtained to evaluate fracture evolutions during hydration for both the connected and unconnected fracture networks. In addition, permeabilities before and after hydration were also quantified. Results from the ambient condition experiment revealed the propagation of fractures, the formation of new fractures, and the formation of better connectivity caused by a more complicated fracture network. However, the fracture evolution of the other three samples under confining pressures are markedly different, including: more unconnected fracture networks, less fracture volume, and a poorer connectivity of fractures.

bio-inspired, mechanical behavior, carbon sequestr↗

Impacts of Glutaraldehyde on Microbial Community Structure and Degradation Potential in Streams Impacted by Hydraulic Fracturing

The environmental impacts of hydraulic fracturing, particularly those of surface spills in aquatic ecosystems, are not fully understood. The goals of this study were to (1) understand the effect of previous exposure to hydraulic fracturing fluids on aquatic microbial community structure and (2) examine the impacts exposure has on biodegradation potential of the biocide glutaraldehyde. Microcosms were constructed from hydraulic fracturing-impacted and nonhydraulic fracturing-impacted streamwater within the Marcellus shale region in Pennsylvania. Microcosms were amended with glutaraldehyde and incubated aerobically for 56 days. Microbial community adaptation to glutaraldehyde was monitored using 16S rRNA gene amplicon sequencing and quantification by qPCR. Abiotic and biotic glutaraldehyde degradation was measured using ultra-performance liquid chromatography--high resolution mass spectrometry and total organic carbon. It was found that nonhydraulic fracturing-impacted microcosms biodegraded glutaraldehyde faster than the hydraulic fracturing-impacted microcosms, showing a decrease in degradation potential after exposure to hydraulic fracturing activity. Hydraulic fracturing-impacted microcosms showed higher richness after glutaraldehyde exposure compared to unimpacted streams, indicating an increased tolerance to glutaraldehyde in hydraulic fracturing impacted streams. Beta diversity and differential abundance analysis of sequence count data showed different bacterial enrichment for hydraulic fracturing-impacted and nonhydraulic fracturing-impacted microcosms after glutaraldehyde addition. These findings demonstrated a lasting effect on microbial community structure and glutaraldehyde degradation potential in streams impacted by hydraulic fracturing operations.

54 ENVIRONMENTAL SCIENCES↗

Distinct Fracture Mineralogy That is Out of Equilibrium With Modern Groundwaters Provides Important Context for Subsurface Life

Rock fracture surfaces in the crust are essential habitat for microorganisms. Fracture‐groundwater interfaces provide physical substrates for biofilm growth and are sources of carbon, nutrients, and electron donors and acceptors. To better understand geochemical processes impacting fracture surfaces and the subsurface microbiome, we identified fractures in archived rock cores from the Soudan formation, which is known to host saline groundwaters and isolated microbial communities dependent on rock‐water interactions. Cores with open fractures were thin sectioned and studied via electron microprobe and synchrotron X‐ray fluorescence microprobe. Most fracture surfaces had mineralogy distinct from that of the bulk rock. Chlorite minerals were abundant on fracture surfaces and had elemental compositions suggesting deposition during late‐stage hydrothermal alteration. Fracture‐lining chlorites likely limit access to iron oxide and sulfide minerals that are active in subsurface biogeochemical cycles. Calcium‐rich rinds were also observed along fracture edges. These rinds were too thin and poorly ordered to be identified via light microscopy or X‐ray diffraction; however, Ca K‐edge micro‐X‐ray absorption near‐edge structure spectroscopy identified them as carbonates, minerals not observed in the bulk rock. Thermodynamic modeling shows that carbonate precipitation is largely unfavorable in Soudan groundwaters, indicating that fracture edge conditions differed from those in modern water samples. Because of the low carbon concentrations in Soudan groundwaters, carbonate rinds likely play an important role in subsurface carbon cycling and may mark fracture surfaces that once hosted biofilms. Overall, this study suggests that fracture alteration can both play an active role in and suppress rock‐water interactions essential to subsurface life.

36 MATERIALS SCIENCE↗

Classification and Localization of Fracture-Hit Events in Low-Frequency Distributed Acoustic Sensing Strain Rate with Convolutional Neural Networks

Summary Distributed acoustic sensing (DAS) has been used in the oil and gas industry as an advanced technology for surveillance and diagnostics. Operators use DAS to monitor hydraulic fracturing activities, examine well stimulation efficacy, and estimate complex fracture system geometries. Particularly, low-frequency DAS can detect geomechanical events such as fracture hits because hydraulic fractures propagate and create strain rate variations in the rock. Analysis of DAS data today is mostly done post-job and subject to interpretation methods. However, the continuous and dense data stream generated live by DAS poses the opportunity for more efficient and accurate real-time data-driven analysis. The objective of this study is to develop a machine learning-based workflow that can identify and locate fracture-hit events in simulated strain rate responses correlated with low-frequency DAS data. In this paper, “fracture hit” refers to a hydraulic fracture originating from a stimulated well intersecting an offset well. We start with building a single fracture propagation model to produce strain rate patterns observed at a hypothetical monitoring well. This model is used to generate two sets of strain rate responses with one set containing fracture-hit events. The labeled synthetic data are then used to train a custom convolutional neural network (CNN) model for identifying the presence of fracture-hit events. The same model is trained again for locating the event with the output layer of the model replaced with linear units. We achieved near-perfect predictions for both event classification and localization. These promising results prove the feasibility of using CNN for real-time event detection from fiber-optic sensing data. Additionally, we use edge detection techniques to recognize fracture-hit event patterns in strain rate images. The fracture-hit location can be identified using recognized pixels in the image. The accuracy of edge detection-based location identification is also plausible, but edge detection is dependent on the assumption of pattern shape and image quality, hence it is less robust compared to CNN models. This comparison further supports the need for CNN applications in image-based real-time fiber-optic sensing event detection.

Engineering↗

Interpretation of Fracture Initiation Points by In-Well Low-Frequency Distributed Acoustic Sensing in Horizontal Wells

Summary Low-frequency distributed acoustic sensing (LF-DAS) exploits the optical phase shift of Rayleigh backscatter in fiber-optic cables to obtain distributed measurements of changes in strain and temperature. Fiber-optic cables are often installed for multistage hydraulic fracture diagnostics in horizontal wells. LF-DAS in an untreated well provides far-field strain measurements, while offset wells are hydraulically fractured. Such a configuration is called crosswell LF-DAS sensing. Crosswell LF-DAS measurements have proved useful in diagnosing fracture hits, fracture azimuth, planarity, cluster efficiency, fracture propagation rates, and the dynamic distance to the fracture front. In contrast, in-well LF-DAS is conducted on the actively fractured well. Due to cool fracture fluid being injected at high injection rates, the strain component of the LF-DAS response is largely obscured by temperature changes. In permanent fiber-optic cable installations, distributed temperature sensing (DTS) is often conducted simultaneously with LF-DAS. An opportunity exists to decouple the temperature and strain components of LF-DAS sensors to observe strain changes on in-well LF-DAS. The LF-DAS response is modeled as linearly dependent on strain and temperature changes. Theoretical LF-DAS temperature and strain sensitivity coefficients are derived based on the changes to the index of refraction and length of the fiber. Using the DTS measurements, temperature changes are computed, smoothed, filtered, and compared to the LF-DAS response. Crossplots of the in-well LF-DAS measurements and temperature changes from DTS measurements far from the actively fractured region are used to validate the theoretical sensitivity coefficients. Uncertainty in the temperature component of the LF-DAS response is quantified. The difficulty in corresponding the different spatial and temporal resolutions of the DTS and LF-DAS measurements is overcome by comparing the responses over a moving temporal and spatial window. If the LF-DAS response at the center of the window agrees with the DTS response within uncertainty, the measurement is filtered out. After filtering, the remaining nonzero in-well LF-DAS measurements are due to changes in strain. The data are then visualized in waterfall plots. The results indicate that the theoretical and observed strain and temperature coefficients agree within 10%. After the temperature component of the in-well LF-DAS response is extracted, the remaining nonzero measurements are located primarily within the actively treated region. Locations with peaks in the strain response are interpreted to indicate fracture initiation points. These fracture initiation points are compared with in-well DTS and high-frequency DAS noise measurements across multiple stages to better understand fracture initiation along the horizontal well.

Engineering↗

Scale-Dependent Fracture-Matrix Interactions and Their Impact on Radionuclide Transport: Development of efficient particle-tracking methods

Matrix Diffusion and Adsorption within a rock matrix are important mechanisms for retarding transport of radionuclides in fractured rock. Due to computational limitations and difficulties in characterizing complex subsurface systems, diffusive exchange between a fracture network and surrounding rock matrix is often modeled using simplified conceptual representations. There is significant uncertainty in “effective” parameters used in these models, such as the “effective matrix diffusivity”. Often, these parameters are estimated by fitting sparse breakthrough data, and estimated values fall outside meaningful ranges, because simplified interpretive models do not consider complex three-dimensional flow. There is limited understanding of the relationship between the effective parameters and rock mass characteristics including network structure and matrix properties. There is also evidence for an apparent scale-dependence in “effective matrix diffusion” coefficients. These observations raise questions on whether fracture-matrix interaction parameters estimated from small-scale tracer tests can be used for predicting radionuclide fate and transport at the scale of DOE field sites. High-resolution three-dimensional Discrete-Fracture-Network-Matrix (DFNM) models based on well-defined local scale transport equations can help to address some of these questions. Due to tremendous advances in computational technology over the last 10 years, DFNM modeling in relatively large domains is now feasible. The overarching objective of our research is to use DFNM modeling to improve fundamental understanding of how effective parameters in conceptual models are related to fracture network structure and matrix properties. An advanced three-dimensional DFNM model is being developed, which combines upscaled particle-tracking algorithms for fracture-matrix interaction and a parallel fracture-network flow simulator. The particle-tracking algorithms allow complexity in flow fields at different scales, and track transport across fracture-matrix interfaces based on rigorous local approximations to the transport equations. This modeling approach can incorporate aperture variability, multi-scale preferential flow and matrix heterogeneity. We developed efficient particle-tracking methods for handling matrix diffusion and adsorption on fracture walls and demonstrated their efficiency for use within the context of large-scale complex fracture network models with variability in apertures across a network of fractures and within individual fractures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2015 Accomplishments-Tritium aging studies on stainless steel. Effects of hydrogen isotopes, crack orientation, and specimen geometry on fracture toughness

This study reports on the effects of hydrogen isotopes, crack orientation, and specimen geometry on the fracture toughness of stainless steels. Fracture toughness variability was investigated for Type 21-6-9 stainless steel using the 7K0004 forging. Fracture toughness specimens were cut from the forging in two different geometric configurations: arc shape and disc shape. The fracture toughness properties were measured at ambient temperature before and after exposure to hydrogen gas and compared to prior studies. There are three main conclusions that can be drawn from the results. First, the fracture toughness properties of actual reservoir forgings and contemporary heats of steel are much higher than those measured in earlier studies that used heats of steel from the 1980s and 1990s and forward extruded forgings which were designed to simulate reservoir microstructures. This is true for as-forged heats as well as forged heats exposed to hydrogen gas. Secondly, the study confirms the well-known observation that cracks oriented parallel to the forging grain flow will propagate easier than those oriented perpendicular to the grain flow. However, what was not known, but is shown here, is that this effect is more pronounced, particularly after hydrogen exposures, when the forging is given a larger upset. In brick forgings, which have a relatively low amount of upset, the fracture toughness variation with specimen orientation is less than 5%; whereas, in cup forgings, the fracture toughness is about 20% lower than that forging to show how specimen geometry affects fracture toughness values. The American Society for Testing Materials (ASTM) specifies minimum specimen section sizes for valid fracture toughness values. However, sub-size specimens have long been used to study tritium effects because of the physical limitation of diffusing hydrogen isotopes into stainless steel at mild temperatures so as to not disturb the underlying forged microstructure. This study shows that fracture toughness values of larger specimens are higher and more representative of the material’s fracture behavior in a fully constrained tritium reservoir. The toughness properties measured for sub-size specimens were about 65-75% of the values for larger specimens. While the data from sub-size specimens are conservative, they may be overly so. The fracture toughness properties from sub-size specimens are valuable in that they can be used for tritium effects studies and show the same trends and alloy differences as those seen from larger specimen data. Additional work is planned, including finite element modeling, to see if sub-size specimen data could be adjusted in some way to be more closely aligned with the actual material behavior in a fully constrained pressure vessel.

08 HYDROGEN↗

Characterization of the Oriskany and Berea Sandstones: Evaluating Biogeochemical Reactions of Potential Sandstone–Hydraulic Fracturing Fluid Interaction

The Marcellus shale, located in the mid-Atlantic Appalachian Basin, has been identified as a source for natural gas and targeted for hydraulic fracturing recovery methods. Hydraulic fracturing is a technique used by the oil and gas industry to access petroleum reserves in geologic formations that cannot be accessed with conventional drilling techniques (Capo et al., 2014). This unconventional technique fractures rock formations that have low permeability by pumping pressurized hydraulic fracturing fluids into the subsurface. Although the major components of hydraulic fracturing fluid are water and sand, chemicals, such as recalcitrant biocides and polyacrylamide, are also used (Frac Focus, 2015). There is domestic concern that the chemicals could reach groundwater or surface water during transport, storage, or the fracturing process (Chapman et al., 2012). In the event of a surface spill, understanding the natural attenuation of the chemicals in hydraulic fracturing fluid, as well as the physical and chemical properties of the aquifers surrounding the spill site, will help mitigate potential dangers to drinking water. However, reports on the degradation pathways of these chemicals are limited in existing literature. The Appalachian Basin Marcellus shale and its surrounding sandstones host diverse mineralogical suites. During the hydraulic fracturing process, the hydraulic fracturing fluids come into contact with variable mineral compositions. The reactions between the fracturing fluid chemicals and the minerals are very diverse. This report: 1) describes common minerals (e.g. quartz, clay, pyrite, and carbonates) present in the Marcellus shale, as well as the Oriskany and Berea sandstones, which are located stratigraphically below and above the Marcellus shale; 2) summarizes the existing literature of the degradation pathways for common hydraulic fracturing fluid chemicals [polyacrylamide, ethylene glycol, poly(diallyldimethylammonium chloride), glutaraldehyde, guar gum, and isopropanol]; 3) reviews the known research about the interactions between several hydraulic fracturing chemicals [e.g. polyacrylamide, ethylene glycol, poly(diallyldimethylammonium chloride), and glutaraldehyde] with the minerals (quartz, clay, pyrite, and carbonates) common to the lithologies of the Marcellus shale and its surrounding sandstones; and 4) characterizes the Berea sandstone and analyzes the physical and chemical effects of flowing guar gum through a Berea sandstone core.

58 GEOSCIENCES↗

Imaging Fracture Networks Using Joint Seismic and Electrical Change Detection Techniques (Final Report)

During the initial phase of this SubTER project, we conducted a series of high resolution seismic imaging campaigns designed to characterize induced fractures. Fractures were emplaced using a novel explosive source, designed at Sandia National Laboratories, that limits damage to the borehole. This work provided evidence that fracture locations could be imaged at inch scales using high-frequency seismic tomography but left many fracture properties (i.e. permeability) unresolved. We present here the results of the second phase of the project, where we developed and demonstrated emerging seismic and electrical geophysical imaging technologies that characterize 1) the 3D extent and distribution of fractures stimulated from the explosive source, 2) 3D fluid transport within the stimulated fracture network through use of a contrasting tracer, and 3) fracture attributes through advanced data analysis. Focus was placed upon advancing these technologies toward near real-time acquisition and processing in order to help provide the feedback mechanism necessary to understand and control fracture stimulation and fluid flow. Results from this study include a comprehensive set of 4D cross-hole seismic and electrical data that take advantage of change detection methodologies allowing for perturbations associated with the fracture emplacement and particulate tracer to be isolated. During the testing the team also demonstrated near real-time 4D electrical resistivity tomography imaging and 4D seismic tomography using the CASSM approach with a temporal resolution approaching 1 minute. All of the data collected were used to develop methods of estimating fracture attributes from seismic data, develop methods of assimilating disparate and transient data sets to improve fracture network imaging resolution, and advance capabilities for near real-time inversion of cross-hole tomographic data. These results are illustrated here. Advancements in these areas are relevant to all situations where fracture emplacement is used for reservoir stimulation (e.g. Enhanced Geothermal Systems (EGS) and tight shale gases).

42 ENGINEERING↗