Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Hot Forging Options for Thick Castings

Uranium alloyed with 10 wt% molybdenum (U-10Mo) is a monolithic nuclear fuel relevant to the National Nuclear Security Administration’s nonproliferation efforts. Research has been underway to optimize processing techniques for the U-10Mo fuel. This study investigated the use of hot compression or “hot forging” on a thick (~1") cast and homogenized U-10Mo plate before standard hot and cold rolling procedures. After plates were cast and homogenized, six samples were cut and forged at 700°C at a strain rate of either 0.10 s –1 or 0.01 s –1 at six levels of reduction. After forging, all samples underwent hot and cold rolling followed by annealing to achieve a final foil thickness of about 0.0085". Samples were taken at each stage of the casting and thermomechanical processing to assess the microstructural evolution. Chemical composition, microstructure, and uranium carbide morphology are presented and assessed in this study. Upon hot forging, dislocations accumulate along the grain boundaries, which serve as nucleation sites for randomly oriented, strain-free grains during subsequent annealing steps. Hot forging and subsequent annealing produced very heterogeneous grain sizes. However, no molybdenum segregation was observed after forging. No obvious trend was observed between forging conditions (strain rate and reduction percentage) and the microstructure after final thermomechanical processing. Upon hot rolling to 0.04" and annealing (700°C for 45 min), the average grain diameters from OM was 17 ± 2 µm across the six different forged samples. The subsequent cold rolling to 0.0085" and then annealing (700°C for 45 min) resulted in an average of 13 ± 2 µm between the six samples. Thus, the starting, as-forged microstructure did not appear to significantly influence the final microstructure of the cold-rolled foil. These results will help with understanding and expanding hot working capabilities for thicker U-10Mo castings. They also provide useful information on the effects of hot forging and its potential use to minimize defects that can arise during subsequent hot and cold rolling procedures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Polycrystalline alloys are used pervasively across structural applications contingent upon extensive experimental testing. A statistically representative number of tests are required to expose the variability in the material's performance, as a result of non-uniform microstructures and associated micromechanical fields. In a more direct means of capturing this pertinent information, multi-modal experimental techniques are presented to measure and track the complete micromechanical state, evolving during loading, of each and every grain within the regions of interest. Specifically, a combination of high-energy X-ray diffraction microscopy and digital image correlation coupled with electron backscatter diffraction are conducted on a specimen for each of the alloys, Haynes 282 and Ti7Al. The results of the multi-modal analysis definitively demonstrate that the degree of heterogeneity increases with deformation level and is used to assess the number of grains necessary for a representative volume element description of the stress state for each of these materials. Moreover, higher resolution imaging is used for identification of the slip system activity and subsequently used to study slip transmission events. An accurate knowledge of the resolved shear stress in adjacent grains (grain interactions) is demonstrated to be a key descriptor of the slip transmission events.

36 MATERIALS SCIENCE↗

Alloying effects on deformation induced microstructure evolution in copper

In this work, we investigated the effects of alloying elements on plastic deformation and microstructure evolution in polycrystalline copper (Cu) and Cu alloyed with 1 wt. % lead (Cu-1 %Pb). These materials were selected due to the size mismatch between Cu and Pb, with the latter forming precipitates at grain boundaries. Multi-modal characterization techniques, including neutron diffraction, electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM), along with finite element simulations were employed to study the deformation behavior across multiple length scales. While both Cu and Cu-1%Pb exhibited similar macroscale response and final deformation textures, both dislocation line profile analysis and TEM revealed increased dislocation density in deformed Cu-1%Pb specimens. The presence of lead precipitates also significantly affected local plastic deformation during compression, with their influence diminishing with increasing strain. These results demonstrate the complex relationships between alloying elements, plastic deformation, microstructural evolution, and material behavior under load. The insights gained from this multi-scale and multi-technique approach contribute to the fundamental understanding of microstructural evolution in immiscible alloys and are valuable for tailoring the properties of structural materials for specific engineering applications.

36 MATERIALS SCIENCE↗

Effects of Al-5Ti-1B master alloy on the microstructural evaluation of a highly alloyed aluminum alloy produced by SIMA process

This study was undertaken to investigate the influence of Al-5Ti-1B master alloy on the structural characteristics of Al-12Zn-3 Mg-2.5Cu aluminum alloy. The optimum amount of Ti containing master alloy for proper grain refining was selected as 6 wt.%. A modified strain-induced, melt-activated (SIMA) process for semi-solid processing of alloys was proposed. In order to examine the effectiveness of the modified SIMA process, the recrystallized microstructures of the Al alloy (Al-12Zn-3 Mg-2.5Cu) prepared by the modified SIMA processes were macroscopically. The modified SIMA process employed casting, warm multi-forging, recrystallization and partial melting instead of the conventional process. Reheating condition to obtain a fine globular microstructure was optimized. The microstructure evolution of reheated Al-12Zn-3 Mg-2.5Cu aluminum alloy was characterized by SEM (Scanning electron microscopy) and optical microscopy. In this study the relation between the induced strain with size and shape of grain size has been studied. Results indicated that with the increase of strain sphericity of particles, their size decreases and sphericity takes place in less reahiting time.

36 MATERIALS SCIENCE↗

Impact of grain boundaries on efficiency and stability of organic-inorganic trihalide perovskites

Organic-inorganic perovskite solar cells have attracted tremendous attention because of their remarkably high power conversion efficiencies. To further improve device performance, it is imperative to obtain fundamental understandings on the photo-response and long-term stability down to the microscopic level. Here, we report the quantitative nanoscale photoconductivity imaging on two methylammonium lead triiodide thin films with different efficiencies by light-stimulated microwave impedance microscopy. The microwave signals are largely uniform across grains and grain boundaries, suggesting that microstructures do not lead to strong spatial variations of the intrinsic photo-response. In contrast, the measured photoconductivity and lifetime are strongly affected by bulk properties such as the sample crystallinity. As visualized by the spatial evolution of local photoconductivity, the degradation process begins with the disintegration of grains rather than nucleation and propagation from visible boundaries between grains. In conclusion, our findings provide insights to improve the electro-optical properties of perovskite thin films towards large-scale commercialization.

14 SOLAR ENERGY↗

Simulations of Stress-induced Twinning and De-twinning: a Phase-field Model

Twinning in metals is a major plastic deformation mode. Here we present a phase-field model to describe twin formation and evolution in a polycrystalline FCC metal under loading and unloading. The model assumes that the twin nucleation, growth and de-twinning is a process of partial dislocation nucleation and slip on successive habit planes. Stacking fault energies, energy pathways ( surfaces), critical shear stresses for the formation of stacking faults, and dislocation core energies are used to construct the thermodynamic model. The simulation results demonstrate that the model is able to predict the nucleation of twins and partial dislocations as well as the morphology of the twin nuclei, and reasonably to describe twin growth and interaction. The twin microstructures at grain boundaries are in agreement with experimental observation . It is found that de-twinning occurs during unloading in performed simulations. However, strong dependence of twin structure evolution on loading history is observed.

36 MATERIALS SCIENCE↗

Modeling shock-induced void collapse in single-crystal Ta systems at the mesoscales

Understanding the role of microstructural heterogeneities on the shock wave propagation and defect evolution behavior is essential to predicting the dynamic response of metals. Heterogeneities, such as voids, provide challenges to understanding the wave propagation behavior as the shock-void interaction can collapse the void and result in large plastic strains and significant heating (hot spot formation) in the metal. Accurate modeling of this phenomenon requires predicting the void collapse mechanisms and the related heat generation and dissipation mechanisms (hotspot formation) that determine the microstructure evolution. While molecular dynamics (MD) simulations can model the void collapse behavior, the time/length scale capabilities pose a challenge to connect with continuum models or the experimental scales. Here, this study presents the capability of the newly developed quasi-coarse-grained dynamics (QCGD) method that extends the MD simulations to larger system sizes and longer times to model this phenomenon. This study uses QCGD simulations to investigate the mechanisms of shock wave interactions with pre-existing voids in single-crystal Ta microstructures for variations in shock pressures, void size, and loading orientations. For a given orientation, the plasticity contributions and rates of void collapse are observed to vary with shock pressures and void size. The larger void sizes and higher pressures result in increased temperatures (hot spots) and faster void collapse rates and unravel the variations in the plasticity contributions. In addition, QCGD simulations investigate the post-collapse microstructure evolution as a release wave travels through the hot spot region. The simulations reveal that the reduction in temperatures due to heat dissipation initiates the dynamic recrystallization behavior in the hotspot regions.

36 MATERIALS SCIENCE↗

Damage initiation and evolution in Al-Si layered microstructures under shock loading conditions at atomic scales

Designing materials with microstructural features like multiphase interfaces have shown significant promise for usage in the next generation defense and nuclear applications. The dynamic response of these interfaces in extreme environments is observed to vary with the deformability of individual phases, which could subsequently alter the favored damage nucleation sites related to spall failure. Here, we investigate the role of spacing of interfaces in a nanocrystalline layered Aluminum-Silicon system on the shock wave propagation behavior, and microstructural and defect evolution using classical molecular dynamics simulations. The simulations are carried out with different hypothetical Al/Si microstructures including variations in the distribution of Si grains as layers in a nanocrystalline Al matrix. The molecular dynamics simulations suggest that spall failure is preferentially initiated at Al/Si interfaces. In addition, for the same system volume and same concentration of Si, a higher number of layers is marked by an increase in shock wave velocity and reduced resistance to spall failure.

36 MATERIALS SCIENCE↗

Imaging grain microstructure in a model ceramic energy material with optically generated coherent acoustic phonons

Characterization of microstructure, chemistry and function of advanced energy materials remains a challenge for instrumentation science with tremendous opportunity for new discoveries. This active area of research is starting to make considerable strides with examples ranging from methodologies that employ bright X-rays, electron microscopy and optical spectroscopy. However, further development of instruments, capable of multimodal measurements, is necessary to fully reveal complex microstructure evolution in realistic environments and dynamical systems that are far from equilibrium. In this regard, laser-based instruments have a unique advantage as multiple measurement methodologies are easily combined into a single instrument using standard optics. A new pump-probe method that uses optically generated acoustic phonons is expanding standard optical characterization by providing depth resolved information. Here we report on a noteworthy extension of this pump-probe method to image grain microstructure in ceria. Rich information regarding the orientation of individual crystallites is obtained by monitoring acoustic phonon velocities and noting how the polarization of the probe beam influences the detected signal amplitude. When paired with other optical microscopies, this methodology will provide new perspectives for optical characterization of ceramic materials.

36 MATERIALS SCIENCE↗

Frictional interactions at high velocity ductile metal interfaces

We have examined the effect of evolution of grain morphology on the frictional force at polycrystalline Al-Al and Al-Ta interfaces as a function of grain size and sliding velocity. We present the results of 8M, 26M and 138M particle NonEquilibrium Molecular Dynamics (NEMD) simulations for grain sizes of 13 and 20 nm. Sample sizes consisted of 3×3×3 and 5×5×5 grains on each side of a sliding interface. We have considered sliding velocities from 20 to 4000 m/s. For velocities below a size dependent critical velocity above which a fluid layer forms, we find enhanced grain coarsening leading to a highly strained, graded final steady state microstructure that exhibits a dynamic morphology for times greater than 5-10 ns. We find that the frictional force is insensitive to the initial grain size distribution due to the evolution of the initial distribution to a new nonequilibrium steady state. We discuss the relationship of these results to single crystal interfaces and the mechanisms for grain size and shape evolution.

36 MATERIALS SCIENCE↗

Effect of solution annealing temperature on precipitation in 2205 duplex stainless steel

In the present study, effect of solution annealing temperature (1050 Degree-Sign C and 1100 Degree-Sign C) and isothermal ageing (700 Degree-Sign C: 15 min to 6 h) on the microstructural changes in 2205 duplex stainless steel has been investigated systematically. Scanning electron microscopy and X-ray diffraction were adopted to follow the microstructural evolution, while an energy dispersive spectrometer attached to scanning electron microscope was used to obtain localised chemical information of various phases. The ferritic matrix of the two phase 2205 duplex stainless steel ({approx} 45% ferrite and {approx} 55% austenite) undergoes a series of metallurgical transformations during ageing-formation of secondary austenite ({gamma}{sub 2}) and precipitation of Cr and Mo rich intermetallic (chi-{chi} and sigma-{sigma}) phases. For solution annealing at 1050 Degree-Sign C, significant amount of carbides were observed in the ferrite grains after 1 h of ageing at 700 Degree-Sign C. {chi} Phase precipitated after the precipitation of carbides-preferentially at the ferrite-ferrite and also at the ferrite-austenite boundaries. {sigma} Phase was not observed in significant quantity even after 6 h of ageing. The sequence of precipitation in samples solution annealed at 1050 Degree-Sign C was found to be carbides {yields} {chi} {yields} {sigma}. On the contrary, for samples solution annealed at 1100 Degree-Sign C, the precipitation of {chi} phase was negligible. {chi} Phase precipitated before {sigma} phase, preferentially along the ferrite-ferrite grain boundaries and was later consumed in the {sigma} phase precipitation. The {sigma} phase precipitated via the eutectoid transformation of ferrite to yield secondary austenite {gamma}{sub 2} and {sigma} phase in the ferrite and along the ferrite-austenite grain boundaries. An increase in the volume fraction of {gamma}{sub 2} and {sigma} phase with simultaneous decrease in the ferrite was evidenced with ageing. - Highlights: Black-Right-Pointing-Pointer Effect of solution annealing temperature on microstructural evolution is studied. Black-Right-Pointing-Pointer {chi} Phase precipitated preferentially in the samples solution annealed at 1050 Degree-Sign C. Black-Right-Pointing-Pointer {sigma} Phase precipitated preferentially in the samples solution annealed at 1100 Degree-Sign C. Black-Right-Pointing-Pointer For SA at 1050 Degree-Sign C, the sequence of precipitation was carbides {yields} {chi} phase {yields} {sigma} phase. Black-Right-Pointing-Pointer For SA at 1100 Degree-Sign C, {sigma} phase precipitated via the eutectoid reaction: ferrite (F) {yields} {sigma} + {gamma}{sub 2}.

36 MATERIALS SCIENCE↗

High pressure FAST of nanocrystalline barium titanate

Here, this work studies the microstructural evolution of nanocrystalline (<1 µm) barium titanate (BaTiO 3 ), and presents high pressure in field-assisted sintering (FAST) as a robust methodology to obtain >100 nm BaTiO 3 compacts. Using FAST, two commercial ~50 nm powders were consolidated into compacts of varying densities and grain sizes. Microstructural inhomogeneities were investigated for each case, and an interpretation is developed using a modified Monte Carlo Potts (MCP) simulation. Two recurrent microstructural inhomogeneities are highlighted, heterogeneous grain growth and low-density regions, both ubiqutously present in all samples to varying degrees. In the worst cases, HGG presents an area coverage of 52%. Because HGG is sporadic but homogenous throughout a sample, the catalyst (e.g., the local segregation of species) must be, correspondingly, distributed in a homogenous manner. MCP demonstrates that in such a case, a large distance between nucleating abnormal grains is required—otherwise abnormal grains prematurely impinge on each other, and their size is not distinguishable from that of normal grains. Compacts sintered with a pressure of 300 MPa and temperatures of 900 °C, were 99.5% dense and had a grain size of 90±24 nm. These are unprecedented results for commercial BaTiO 3 powders or any starting powder of 50 nm particle size—other authors have used 16 nm lab-produced powder to obtain similar results.

36 MATERIALS SCIENCE↗

Capture efficiency and bias from the defect dynamics near grain boundaries in BCC Fe using mesoscale simulations

The capture efficiency describes the capability of a sink, such as a grain boundary (GB), dislocation, and void, to absorb point defects (PDs). The bias defines the difference in capture efficiency between the absorption of a vacancy and dumbbell at a sink. Complete kinetic information on PDs, including diffusion barriers and diffusion orientations, as well as accurate saddle points, are needed to determine the capture efficiency and bias at a sink accurately, which is computationally demanding. Here, in the present study, the Self-Evolving Atomistic Kinetic Monte Carlo (SEAKMC) method was used to investigate the defect dynamics of PDs near different types of grain boundaries (GBs) (with both $\langle$100$\rangle$ and $\langle$110$\rangle$ families) accurately in body-centered cubic (BCC) iron (Fe). The capture efficiency, sink strength, and bias factor of different types of GBs were determined in Fe, which, different from traditional rate theory estimation, showed a distinct capture efficiency, sink strength, and bias in different GBs. The results demonstrate a strong positive correlation between the capture efficiency and the GB strain width, instead of the GB misorientation, GB energy, or GB-PD binding energy, which have been investigated previously. This work provides valuable insight into the radiation-induced microstructural evolution of GBs.

36 MATERIALS SCIENCE↗

Interstitial hydrogen enhances the mobility of some grain boundaries in tungsten

Segregation of interstitials at a grain boundary (GB) is known to generally lower its mobility. This phenomenon, called 'solute-drag', has important ramifications on the process of recrystallization and microstructural evolution. Here, we present predictions from molecular dynamics (MD) simulations which demonstrate that interstitial hydrogen in tungsten can in fact increase the mobility of some GBs which exhibit shear coupling. Assuming a disconnection-based mechanism, activation energies and pre-factors for disconnection nucleation are predicted from simulations of shear-coupled motion. In GBs where enhanced mobility is predicted, interstitial H reduces both the activation energy and the pre-factor for disconnection nucleation, thus effectively increasing the mobility. For GBs with diminished mobility, MD predicts that presence of interstitial H reduces the pre-factor and, in some cases, increases the activation energy. The reduction in the activation energy inferred from MD simulations are confirmed by nudged elastic band calculations. Temperature-dependent structural transitions are observed for some GBs, and the effect of interstitial H is found to change with the changes in structure. The effect of interstitial H is predicted to be complex and highly variable, providing some plausible explanations for experimental observations on the recrystallization of tungsten in presence of H-loaded plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The evolution history of superalloy powders during hot consolidation and plastic deformation

Highlights: • Element segregations in a powder metallurgy superalloy at different states are identified. • The surface energy drives precipitation of oxides, carbides, and γ' particles on powder surface during hot consolidation. • Prior particle boundary structure is distorted and more uniformly refined grains are obtained after hot extrusion. - Abstract: Powder metallurgy superalloys are widely used to produce critical rotating parts in turbine engines. However, the issues like what is the driving force of precipitation on prior particle boundary (PPB) during consolidation and how the PPB structure evolves during plastic deformation still remain to be resolved. In this study, with the characterization of the microstructure evolution from powder, consolidation, to plastic deformation, the segregation of alloying elements on the particle boundaries at elevated temperature was analyzed by equilibrium thermodynamic calculations, and the distortion of PPB structure under large plastic deformation was quantitively simulated by finite element (FE) methods. The results indicated that surface energy serves as the main driving force of PPB precipitation and hot extrusion could distort the PPB structure and yield more uniformly refined grains.

36 MATERIALS SCIENCE↗

Microstructural and magnetic characterization of iron precipitation in Ni-Fe-Al alloys

The influence of annealing on the microstructural evolution and magnetic properties of Ni{sub 50}Fe{sub x}Al{sub 50-x} alloys for x = 20, 25, and 30 has been investigated. Solidification microstructures of as-cast alloys reveal coarse grains of a single B2 type {beta}-phase and typical off eutectic microstructure consisting of proeutectic B2 type {beta} dendrites and interdendritic eutectic for x = 20 and x > 20 at.% Fe respectively. However, annealing at 1073 K results in the formation of FCC {gamma}-phase particles along the grain boundaries as well as grain interior in x = 20 at.% Fe alloy. The volume fraction of interdentritic eutectic regions tend to decrease and their morphologies start to degenerate by forming FCC {gamma}-phase for x > 20 at.% Fe alloys with increasing annealing temperatures. Increasing Fe content of alloys induce an enhancement in magnetization and a rise in the Curie transition temperature (T{sub C}). Temperature scan magnetic measurements and transmission electron microscopy reveal that a transient rise in the magnetization at temperatures well above the T{sub C} of the alloys would be attributed to the precipitation of a nano-scale ferromagnetic BCC {alpha}-Fe phase. Retained magnetization above the Curie transition temperature of alloy matrix, together with enhanced room temperature saturation magnetization of alloys annealed at favorable temperatures support the presence of ferromagnetic precipitates. These nano-scale precipitates are shown to induce significant precipitation hardening of the {beta}-phase in conjunction with enhanced room temperature saturation magnetization in particular when an annealing temperature of 673 K is used. - Research Highlights: {yields} Evolution of microstructure and magnetic properties with varying Fe content. {yields} Transient rise in magnetization via the formation of ferromagnetic phase. {yields} Enhancements in saturation magnetization owing to precipitated ferromagnetic phase. {yields} Nanoscale precipitation of ferromagnetic BCC {alpha}-Fe confirmed by TEM. {yields} Hardness of the {beta}-phase correlates with room temperature saturation magnetization.

36 MATERIALS SCIENCE↗

Transient Rheological Behavior of Semisolid SEED-Processed 7075 Aluminum Alloys in Rapid Compression

The transient rheological behavior and microstructure evolution of semisolid SEED-processed 7075 aluminum alloys were studied using the rapid compression tests. The effects of the TiB{sub 2} grain refinement on the grain morphology and size of semisolid slurries were investigated. Results indicated that the grain refiner could reduce the grain size and improve the globularity of α-Al grains. The grain-refined alloy can be easily deformed at a wide range of solid contents (0.42 to 0.53 Fs), in which the deformation level appears to be independent from the solid content. Under the transient state, the apparent viscosity decreased with increasing shear rate to a minimum value and followed by an increase as the shear rate decreased. The apparent viscosity of the base alloy exhibited a dependency on the solid content, while the apparent viscosity of the grain-refined alloy in the decreasing or increasing shear rate periods was not substantially influenced by the solid content. The viscosity as a function of applied shear rate can be described using the power law viscosity model. The differences in the flow behavior index (n) and the consistency index (k) for two alloys were discussed.

36 MATERIALS SCIENCE↗

An EBSD Evaluation of the Microstructure of Crept Nimonic 101 for the Validation of a Polycrystal–Plasticity Model

Nimonic 101 is one of the early nickel-based superalloys developed for the use in gas turbines. In such environments, the material is exposed to a combination of both high temperatures and mechanical loads for a long duration. Hence, thermal creep is of the utmost concern as it often limits service life. This study focuses on creep tests, carried out on Nimonic 101 at different temperatures under a constant tensile load of 735 MPa. To characterize the microstructural evolution, electron backscatter diffraction (EBSD) measurements were employed before and after loading. At higher temperatures, a significant change of the microstructure was observed. The grains elongated and aligned their orientation along the load axis. In parallel, a crystal plasticity material model has been set up in the classical large deformation framework. Modeling results are compared to the acquired EBSD data.

36 MATERIALS SCIENCE↗