SEARCH · Search NASA

Results for “High burnup”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Fission Product Quantification and Burnup Analysis via Gamma Spectrometry of the AGR-5/6/7 TRISO Fuel Experiment

Five capsules containing varying configurations of TRISO fuel compacts were irradiated in the most recent Advanced Gas Reactor (AGR) TRISO test campaign, AGR-5/6/7. As part of the post-irradiation examination (PIE) of this work all the fuel compacts and capsule graphite holders were measured with the Precision Gamma Scanner (PGS) to determine isotopic activities and locations using gamma spectrometry. Measuring the compacts allowed for the comparison of physics model depletion calculations with the measured compact activity to validate models. These measurements also are used to find compacts of interest with low fission product retention that may be tested in subsequent PIE. Measurements of the holders can confirm fission product distribution and migration. Of the isotopes measured, Cs-137 and Cs-134 were used to estimate location of failed particles as well as determine a measured burnup estimation. Results from Capsule 1 compacts and the holder indicate many fuel particle failures occurred. There are high amounts of cesium in the holder near Stack 9 of Capsule 1 that corresponds to low fractions?measured-to-calculated (M/C) ratio?of cesium remaining in those compacts. All other capsules had cesium retention ratios near 1. The isotope 110mAg had less consistent results. Capsule 2 compacts exhibited a M/C of 0.20, much lower than anticipated for the temperatures these compacts underwent. Capsule 3 experienced much higher temperatures, >1300C and had an average M/C of 0.75. These are the opposite results than what was predicted by past AGR experiments for the relationship between temperature and isotope retention. Capsule 4 and 5 showed good fission product retention and agreement with the physics model predictions. The burnup results from the PGS measurements showed strong agreement between the physics models and the measured values. Using a ratio of Cs-134/Cs-137 to calculate the burnup match closely with the physics models. Additionally, the Cs-137 burnup results were less accurate but extremely close to the model results.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

ATF Cladding Mechanical Properties Report: Capability Demonstration

This report documents post-irradiation examination (PIE) activities performed in FY 2025 at Oak Ridge National Laboratory on chromium-coated (Cr-coated) and uncoated advanced zirconium alloy claddings irradiated in the High Flux Isotope Reactor (HFIR) to approximately 4 displacements per atom (dpa), corresponding to ~40 GWd/t burnup. Specimens were prepared in axial tension (ATT) and ring tension (RTT) geometries, and passive silicon carbide thermometry was employed to determine irradiation temperatures, which averaged 38–43 °C below the 330 °C design target.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Irradiation of UC1+x kernels using the MiniFuel vehicle: Microstructure, phase analysis, and initial post-irradiation examination

Uranium carbide is a candidate fuel form for a wide range of advanced reactors, including larger Generation IV reactors as well as small modular reactors and microreactors. However, its commercial deployment timeline faces challenges via traditional qualification approaches. To address this issue, an accelerated fission rate irradiation test was performed to collect basic fuel performance data to inform fuel performance models and potential future integral tests. Hyperstoichiometric UC (UC1+x) kernels were irradiated in the High Flux Isotope Reactor using the MiniFuel irradiation vehicle. The test matrix spanned two temperature regimes (700 °C and 800 °C) and burnup levels (1.8 % FIMA and 2.8 % FIMA). Between 21 and 63 kernels were tested at each unique temperature and burnup condition. As-fabricated microstructural analysis revealed a multiphase composition with UC, UC2, UC2−y, and U-C-O bearing phases for the irradiated kernels. Following irradiation, fission gas release, swelling, and microstructures were analyzed. Measured fission gas release was below 5 % for all irradiation conditions, reaching a maximum at the highest temperature and burnup condition. A binary swelling response was observed; the lower burnup and temperature conditions resulted in negligible swelling, but the higher burnup and temperature conditions produced significant anisotropic swelling and densification in a subset of kernels. The basic microstructural exams of kernels following irradiation were not capable of showing a correlation between kernels that exhibited excessive swelling and those that did not. Characterization of a subset of samples using the Advanced Photon Source and more detailed microstructural examination of unirradiated kernels revealed that a subset of kernels contained very high UC2 phase fractions. The anomalous swelling response is hypothesized to have been driven by this chemical variation. The results of this irradiation highlight the potential of accelerated fission rate irradiation testing to explore such behaviors and inform the development of fuel specifications.

Adorno Lopes, Denise [ORNL] (ORCID:000900023705987↗

DOE OSTI2024

UO 2 -Liquid Metal Suspension Fuel Concept: Alloy Selection and Depletion Calculations

A novel nuclear fuel was recently proposed that consists of UO 2 particles suspended in a liquid metal mixture. Two liquid metal candidates were identified: BiPbSn and PbSn. Scoping simulations were performed on an over-simplified reactor core that showed a potential limit on achievable burnup. Those findings led to two questions that needed to be addressed: What is the corrosion behavior of the liquid metals toward Zircaloy-4 (Zr4)? And what level of burnup can the fuel be expected to achieve? This report documents efforts to answer both of those questions. First, corrosion experiments were performed between the liquid metal candidates and Zr4 coupons. Second, the previous scoping simulations were expanded to include depletion analyses so that maximum burnups could be estimated. At 400°C, neither PbSn nor BiPbSn caused significant corrosion to the Zr4 coupons. At 600°C, BiPbSn did not cause significant corrosion, but PbSn did. In addition, pure bismuth and pure tin were both highly corrosive, whereas pure lead was non-corrosive. The depletion simulations found that low-enriched fuel could maintain light-water reactor operating temperatures but achieve a burnup of only about one-third of existing reactors. Higher enrichments could achieve burnups equal to or higher than those of existing reactors but at the expense of higher operating temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Development and Standup Testing of a System to Observe Fission Gas Release During Transient Heating of Nuclear Fuel Element Segments

As part of an effort to increase the burnup of nuclear fuels used in Light Water Reactors, the mechanisms and timing of fission gas release during high temperature transients must be studied. In this work, a system was built to observe fission gas release of fuel element sections under evacuated conditions, at temperatures up to 800 °C. System capabilities and limitations are overviewed in this report. The system was further tested with a hydrogen-infused titanium foils and gas release was observed in agreement with literature observations. Pressure was monitored with two sensors, and temperature was monitored using a thermocouple and a pyrometer with continuous visual imaging.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

TRANSPORTATION CONSIDERATIONS FOR USED FUEL AND ADVANCED NUCLEAR ENERGY TECHNOLOGIES

This study focuses on requirements and challenges pertaining to advanced transportable nuclear energy systems, which are currently in development and feature varying degrees of mobility. These reactors mostly use high-assay low-enriched uranium (HALEU) fuel, and only limited refueling is required during their lifecycles. Due to the smaller source terms, higher burnup fuel, and potentially higher thermal efficiency involved, the waste inventory will be less than that generated by conventional light-water reactors. However, the relevant regulatory requirements must be met when transporting HALEU fuel (whether fresh or used) inside the reactor vessel—mainly the fuel material transportation, siting, and physical protection requirements outlined in US Nuclear Regulatory Commission (NRC) regulations 10 CFR 71 and 73. Spent nuclear fuel (SNF), as well as irradiated fuel (used during any interval of reactor operation), contains highly radioactive materials that generate heat and necessitate special precautions during transportation. This study addresses the challenges that this incurs, and outlines potential solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

TRANSPORTATION CONSIDERATIONS FOR USED FUEL AND ADVANCED NUCLEAR ENERGY TECHNOLOGIES

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Implementation of an Experimental Setup Based on the Three-Omega Method for Thermal Conductivity Measurements of Molten Salts

Molten salt reactors (MSRs) are one of the most promising next-generation nuclear reactor designs which use molten salts as the fuel and coolant. To design, model, predict, license, and operate MSRs, the behavior of the fuel and coolant must be understood as a function of temperature and irradiation, i.e., burnup. Of particular importance and complexity is the reliable and reproducible measurement of thermal conductivity of molten salts at high temperatures (> 500 °C). Thermal conductivity provides information on the rate at which heat passes through a specified material and is dependent on chemical composition. Currently, in the national laboratory complex, several methods for measuring thermal conductivity on molten salt systems are under development, however, to date, consistent data have not been produced. Typically, thermal conductivity measurements of high-temperature melts have been conducted by using the Transient Hot Wire (THW) method where thermal conductivity is determined by the change in temperature over time at a certain distance from a heating wire. Another time-dependent technique is the laser flash method, commonly used for solid samples. Laser flash requires prior measurements of density and heat capacity to calculate the thermal conductivity of the sample, introducing additional measurement errors. Steady state and time-dependent measurements such as THW and laser flash have errors from convection and ambient temperature fluctuations (heat radiation). In order to produce high fidelity thermal conductivity data, a measurement technique needs to be developed that will reduce the effect of convection at high temperatures by measuring in a very fast time window. In addition, to measure on actinide and irradiated salts the sample size should be small. Therefore, this project aims to develop a frequency-domain technique based on the three-omega (3?) method, previously proven to work on solids, nanofluids and low temperature solar salts (25 to 250 °C). If the 3?-device can be designed with materials that can withstand high temperatures (>500 °C) and can be configured to reduce errors due to convection, then it would prove to be a valuable technique for ensuring thermal conductivity on molten salt systems needed for MSR development. For this proposal, the 3? instrument will be designed, assembled, and tested on non-radioactive salts before being used on actinide bearing salts. In addition, a thermal model will be developed to determine the thermal conductivity of the sample from the measured thermal oscillation of the sensor. Because 3? is a direct method that requires a small volume of sample and works in a very fast time window, it will aid in suppressing the interference due to convection which is ideal when working with high temperature liquid samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

High volume packing fraction TRISO-based fuel in light water reactors

We report that for a decade, fully ceramic microencapsulated (FCM) fuel, containing tri-structural isotropic (TRISO) fuel particles in a silicon carbide (SiC) matrix, has been investigated as an accident-tolerant fuel for light water reactors (LWRs). Other examples exist of TRISO-based concepts for LWR fuels with different matrix materials. Previous studies assumed TRISO particle volume packing of approximately 0.44 in SiC (or another) matrix, the highest realistic packing fractions possible with conventional manufacturing. Recent advances in advanced manufacturing have yielded the development and demonstration of a fuel form that consists of conventionally manufactured TRISO particles in a 3D-printed SiC matrix with significantly higher possible TRISO packing fractions (0.5–0.7). This increased uranium loading enhances the viability of using TRISO-based particle fuel forms in LWRs. The viability of high-packing-fraction TRISO-based particle fuel forms in LWRs is assessed from the perspective of fuel cycle length, achievable fuel burnup, reactivity coefficients, and fuel cycle performance. Higher-packing-fraction TRISO-based fuel enables either longer cycle lengths (by ~25% at a packing fraction of 0.55 relative to 0.44) at a constant enrichment or decreased enrichments (by ~25% at a packing fraction of 0.55 relative to 0.44) at a constant cycle length. Studies of different fuel kernel types (uranium nitride, uranium oxycarbide, and uranium carbide) yield similar results, although the cycle length of uranium oxycarbide is shorter than for uranium nitride or uranium carbide (due to the lower density of uranium oxide). This work also characterized the production of 14 C resulting from neutron absorption in 14 N during operation for uranium mononitride fuel kernels; the ratio of 14 C/N was 1–2 at. % at discharge. For the fuel cycle evaluation, the activity of spent nuclear fuel and high-level waste at 100 and 100,000 years was lower for high-packing-fraction fuels than for conventional LWR fuel. Environmental impact metrics were similar overall, but higher on the front end of the fuel cycle and lower on the back end of the fuel cycle. Reactivity coefficients of higher-packing-fraction TRISO-based fuel were reasonable compared with those of conventional fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Advanced High-Temperature Sodium-Cooled Thermal Reactors Using Less Than 10% Enriched UO 2 Fuel

Here, this paper presents a 1200-MW(thermal) advanced sodium-cooled thermal reactor concept that uses online refueling of 3.5% to 9.95% enriched UO2 fuel pin bundles; uses either graphite or beryllium oxide (BeO) as a neutron moderator; reaches outlet temperatures of 650°C enabling a thermal efficiency of at least 45%; has a high specific power of 133 W/g U; has average power densities of 16.4 and 43.2 W/cm 3 with graphite and BeO, respectively; reaches an average discharge burnup of 100 MWd/kg U; and generates 52% less spent fuel volume, 28% less fission products, and 47% to 64% less transuranics than a typical large pressurized water reactor for the same amount of electricity produced.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Swelling and Fission Gas Release of U-10Mo and U-17Mo Following Neutron Irradiation at 250 – 500°C

The performance of metallic fuel alloys, U-10Mo and U-17Mo, was examined using the MiniFuel test system in the High Flux Isotope Reactor. Approximately 0.8 mm thick disks were irradiated at target temperatures of 250°C, 350°C, 450°C, and 500°C up to three different fission densities, culminating at a maximum fission density of 6.8 × 10 20 cm −3 . Fission rates decayed from 3 – 6 × 10 13 cm −3 s −1 to 2 – 4 × 10 13 cm −3 s −1 over the course of the longest, eight cycle, irradiation as the 235 U was consumed and the 239 Pu concentration accumulated. Actual irradiation temperature on the last day of irradiation was measured via dilatometry using the SiC passive thermometry recovered from the MiniFuel subcapsules and compared favorably with the thermal calculations using as-built geometry and test conditions. Furthermore, average simulated temperatures were within 50°C of the target temperatures, except for the 500°C irradiation, for which the temperature variation was 62°C, 32°C, and 90°C in the in two, four, and eight cycle irradiations, respectively. Fission gas release (FGR) measurements showed no release above recoil for any U-17Mo fuels or for the U-10Mo fuel irradiated at 250°C. Finally, significant (40%–80%) FGR was found for the medium- to highest-burnup U-10Mo samples irradiated at target temperatures 350°C–500°C. Significant FGR correlated with sample thickness swelling, which was as high as 13%–35% for high-release samples and below 7% for all other (low–gas release) samples.

FGR↗

DOE OSTI2026

The Use of Microelectrodes in Molten Salt Electrochemistry

Molten salts have attracted considerable interest as essential media for advanced high-temperature technologies, including molten salt reactors, thermal energy storage, high-temperature electrolysis, and pyrochemical processing. Their ability to remain stable in liquid form at elevated temperatures, combined with favorable thermophysical properties and wide electrochemical windows, makes them highly suitable for applications involving heat transfer, energy storage, and hightemperature electrochemical processing. However, despite these advantages, molten salts present challenges due to their chemically reactive nature at high-temperatures, especially in the presence of oxidizing impurities. Salt chemistry can fluctuate through interactions with impurities over time, or fuel burnup in the case of molten salt reactors, often leading to the dissolution of metal species. This dynamic environment not only results in complex redox behavior but also promotes corrosion, which is rarely uniform and frequently manifests as localized degradation driven by structural materials’ compositional differences, electrochemical imbalances, and microstructural susceptibilities.

Kim, Changkyu [University of Wisconsin-Madison, WI↗

DOE OSTI2025

IMPACT-01 Assembly Overview [Slides]

The Irradiated Material Properties Accelerated Characterization Test (IMPACT) series of experiments will irradiate three metallic fuel alloy specimens with embedded thermal conductivity probes in the Advanced Test Reactor (ATR). Metallic fuel alloys have long been under investigation for use in advanced reactors on account of their high thermal conductivity. Metallic fuel undergoes dramatic microstructural changes early in life due to fission gas swelling until ~2-3 at% burnup when pores interconnect, thus allowing fission gas to escape into the fuel pin plenum and swelling effectively ceases. The evolution of metallic fuel thermal conductivity during this early phase has never been successfully measured in situ. This experiment will be designed to use advances in measurement sciences to characterize how thermal transport properties evolve while in reactor. The IMPACT experiment consists of three metallic fuel rodlets with thermal conductivity probes axially centered within the fuel specimen. This presentation is an overview of the IMPACT-01 assembly process with a focus MFC fuel fabrication and experiment assembly steps.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Nuclear fuel irradiation testbed for nuclear security applications

The nuclear security community has long been interested in the identification and quantification of nuclear material signatures to understand a material’s provenance, use, and ultimate application. New forensics signatures and methods intended for non-traditional or advanced nuclear fuel applications require fuel irradiation experiments to demonstrate viability and validity. Integral fuel irradiations have historically required significant costs and long timelines to design, irradiate, and characterize. This paper describes how a recently developed nuclear fuel irradiation testbed can be used to provide a low cost, rapid turnaround, modular test environment for irradiation and evaluation of nuclear fuel specimens for nuclear security applications. The irradiation testbed houses six small ‘MiniFuel’ samples within hermetically sealed capsules inside targets that can be removed in between each ∼25-day operating cycle of the High Flux Isotope Reactor (HFIR). As many as nine targets can be irradiated using a single irradiation position (reflector region) in HFIR, allowing for varying irradiation temperatures and burnups. A suite of hot cell capabilities have been established to perform post-irradiation examination for measuring performance (e.g., fuel swelling, fission gas release) and facilitating experiment disassembly for subsequent property measurements, microstructural analysis, or chemical assay. This new testbed allows fuel irradiations to be conducted on an accelerated timeframe to enable rapid proof of concept testing and to provide reference material for nuclear fuel security applications. Recent applications using this testbed include the testing of isotopic taggants in UO 2 fuel (intentional forensics), testing of U-10Mo fuel for down-conversion of highly enriched uranium–fueled reactors, and the production of irradiated UO 2 fuel material for signature analysis of its isotopic composition (plutonium, fission gases, etc.).

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

DOE OSTI2022

Pellet cladding mechanical interaction as a potential failure mechanism during a control rod drop accident in a boiling water reactor

Boiling water reactors (BWRs) represent approximately one-third of the operating fleet in the United States, contributing significantly towards the global effort in reducing carbon emissions. Even though most of the operating fleet has been in operation for quite some time, continued advancements in new nuclear fuel (such as accident tolerant fuel) or operating regimes (such as power up-rates and higher burnup operation) necessitates similar advancements in modeling and simulation capabilities. Bison, a component of the Virtual Environment for Reactor Applications (VERA), is a high-fidelity fuel performance code able to explore the fuel performance of a wide variety of fuel types in one-, two-, and three-dimensions. Until recently, the code had not been used for analyses of BWRs. Modeling capabilities have been added for Gd-bearing UO{sub 2} and pure zirconium liners. New models have been added based upon the U.S. Nuclear Regulatory Commission (NRC) guide-lines for hydrogen pickup in Zircaloy-2 claddings and pellet-clad mechanical interaction (PCMI) failure during a reactivity insertion accident (RIA), known as a rod drop accident (CRDA) in BWRs. Implementing and/or improving Bison modeling capabilities extended its analytical reach to areas beyond its original intended purpose. This paper demonstrates one of these capabilities as a proof of concept. Recently developed models enable Bison to provide an alternate approach for cladding integrity determination in CRDA evaluations, which currently use bounding conservative estimates. As part of this demonstration, NRC guidance on hydrogen-pickup and PCMI failure models were utilized in this research. Even though more research is needed in establishing right inputs and process in this area, this paper demonstrates Bison's ability to determine cladding integrity in a CRDA evaluation. This first of a kind demonstration is a proof of concept in this area, which could potentially be extended to a number of other areas where a more accurate cladding integrity determination would be needed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2025

ROADRUNNER MiniFuel Experiment: Readiness for Insertion

The Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments (ROADRUNNER) campaign is a collaborative irradiation experiment designed to evaluate the performance of uranium nitride (UN) fuel fabricated with controlled variations in density and impurity content. Oak Ridge National Laboratory’s MiniFuel irradiation platform and the High Flux Isotope Reactor (HFIR) are being used to irradiate six targets containing 36 UN miniature disks. These targets have been assembled to systematically investigate burnup and temperature effects under accelerated irradiation conditions. This report documents the finalized test plan, describes the experiment assembly and subcapsule integration process, and confirms the readiness of all ROADRUNNER targets for HFIR insertion. All targets have passed quality control procedures, and five have begun irradiation. The campaign will provide critical performance data to support fuel model validation and future UN qualification efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Initial study on cross section generation requirements for a PBR equilibrium core

A Serpent model of the HTR-PM equilibrium core was developed for use in cross section prepa-ration studies in order to guide methods development for the Griffin reactor multiphysics applica-tion. The model includes detailed isotopics for 10 distinct pebble burnup groups in 126 core zoneswith unique fuel and moderator temperatures obtained from a coupled neutronics-thermal-fluidsequilibrium core calculation using Griffin-Pronghorn. A sensitivity study of the fuel and mod-erator temperatures for various core regions was performed with the MOOSE stochastic tools.The results show that the uncertainties are, not unexpectedly, dominated by the value of the fluidtemperature and that the power level, heat transfer coefficient and effective conduction to neigh-boring pebbles and fluid constitute, at best, second order effects. The temperature uncertaintyrange varies from 28 K to 57 K at the core entry and exit planes, respectively, but these val-ues are probably higher. We still have to quantify the significance of these uncertainties in thepreparation of cross sections, which will be postponed for future work. In addition, we verifythat the single effective pebble approach works well for the preparation of region averaged crosssections in the infinite domain approximation. Nevertheless, there are significant discrepanciesin the cross sections when compared to the multi-pebble model. This could affect the predictionof peak values and in the depletion calculation. We conclude that is highly desirable for futurestudies with Griffin to be able to handle both the ?effective? pebble approximation and the multi-pebble approach for the various pebble burnup groups. This enables Griffin users the flexibilityto perform higher-fidelity studies. Finally, we initiate the preparation of cross sections for variouscore regions from the full core Serpent reference model. We quantify the differences in 26 groupcross sections from infinite domain models. These reference cross sections will serve to validatethe double heterogeneity, self-shielding, and spectrum-correction methods in Griffin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Initial study on cross-section generation requirements for a PBR equilibrium core

A Serpent model of the equilibrium core HTR-PM small modular nuclear reactor in China, was developed for use in cross-section preparation studies in order to guide methods development for the Griffin reactor multiphysics application. The model includes detailed isotopics for 10 distinct pebble burnup groups in 126 core zones with unique fuel and moderator temperatures obtained from a coupled neutronics-thermal-fluids equilibrium core calculation using Griffin-Pronghorn. A sensitivity study of the fuel and moderator temperatures for various core regions was performed with the MOOSE stochastic tools. The results show that the uncertainties are, not unexpectedly, dominated by the value of the fluid temperature and that the power level, heat transfer coefficient and effective conduction to neighboring pebbles and fluid constitute, at best, second order effects. The temperature uncertainty range varies from 28 K to 57 K between the core entry and exit planes, respectively, but these values are probably higher. We still have to quantify the significance of these uncertainties in the preparation of cross-sections in future work. In addition, we verified that the effective pebble approximation used in the PEBBED and V.S.O.P. computer codes works well for the preparation of region averaged cross-sections. Nevertheless, there are some discrepancies in the cross-sections when compared to the multi-pebble model, which could affect the prediction of peak values and the depletion calculation. We conclude that is highly desirable for future studies with Griffin to be able to handle both the 'effective' pebble approximation and the multi-pebble approach for various pebble burnup groups. This enables Griffin users with the flexibility to perform higher-fidelity studies. Finally, we initiated the preparation of cross-sections for various core regions from the full core Serpent reference model. We quantified the differences in 26 group cross-sections from infinite domain models versus the full core approach. These reference cross-sections will serve to verify the double heterogeneity, self-shielding, and spectrum-correction methods in Griffin. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗