Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hydrodynamic stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Unstable transition properties of the driven magnetohydrodynamic sheet pinch

The unstable transition behavior of a bounded current-carrying two-dimensional magnetofluid is explored, using the hydrodynamic theory developed for parallel shear flows as a guide. Nonlinear excitation of the higher wavenumbers results in the development of electric current sheets of finite extent, as well as the formation of 'attraction currents' centered at the magnetic O-points. A secondary instability mechanism, the dynamic tearing of the electric current sheet, is also observed. This dynamic tearing leads to sawtoothlike temporal oscillations in certain global quantities. The long-time state of the system resembles a nonlinearly saturated state with significant excitation of many wavenumbers. Some features of this state can be understood by means of a Landau nonlinear stability theory based on certain assumptions about the perturbation energy balance.

Dahlburg, R. B.↗
NASA NTRS1994

Evolution of the martian atmosphere

Carbon dioxide, nitrogen, and the nonradiogenic and radiogenic noble gases are tracked from primordial inventories to their present states in a revised model of atmospheric evolution on Mars. Elemental and isotopic abundances evolve by hydrodynamic escape, impact erosion, outgassing, sputtering, photochemical escape of nitrogen, and carbonate formation and recycling. Atmospheric history is divided into early and late evolutionary periods, the first characterized by high CO2 pressures and a possible greenhouse and the second by a low pressure cap-regolith buffered system initiated by polar CO2 condensation approximately 3.7 Gyr ago. During early evolution the Xe isotopes are fractionated to their present composition by hydraulic escape, and CO2 pressure and isotopic history are dictated by the interplay of losses to erosion, sputtering, and carbonate precipitation, additions by outgassing and carbonate recycling, and perhaps also by feedback stabilization under greenhouse conditions. Atmospheric collapse near 3.7 Gyr leads to abrupt increases in the mixing ratios of preexisting Ar, Ne, and N2 at the exobase and their rapid removal by sputtering. Current abundances and isotopic compositions of these light species are therefore entirely determined by the action of sputtering and photochemical escape on gases supplied by outgassing during the late evolutionary epoch. The present atmospheric Kr inventory also derives almost completely from solar-like Kr degassed during this period. Consequently, among current observables, only the Xe isotopes and delta(C-13) survive as isotopic tracers of atmospheric history prior to its transition to low pressure.

Pepin, Robert O.↗
NASA NTRS1998

Hydrodynamic Analyses and Evaluation of New Fluid Film Bearing Concepts

Over the past several years, numerical and experimental investigations have been performed on a waved journal bearing. The research work was undertaken by Dr. Florin Dimofte, a Senior Research Associate in the Mechanical Engineering Department at the University of Toledo. Dr. Theo Keith, Distinguished University Professor in the Mechanical Engineering Department was the Technical Coordinator of the project. The wave journal bearing is a bearing with a slight but precise variation in its circular profile such that a waved profile is circumscribed on the inner bearing diameter. The profile has a wave amplitude that is equal to a fraction of the bearing clearance. Prior to this period of research on the wave bearing, computer codes were written and an experimental facility was established. During this period of research considerable effort was directed towards the study of the bearing's stability. The previously developed computer codes and the experimental facility were of critical importance in performing this stability research. A collection of papers and reports were written to describe the results of this work. The attached captures that effort and represents the research output during the grant period.

Keith, Theo G., Jr.↗
NASA NTRS2003

Technical Evaluation Report, Part A - Vortex Flow and High Angle of Attack

A symposium entitled Vortex Flow and High Angle of Attack was held in Loen, Norway, from May 7 through May 11, 2001. The Applied Vehicle Technology (AVT) panel, under the auspices of the Research and Technology Organization (RTO), sponsored this symposium. Forty-eight papers, organized into nine sessions, addressed computational and experimental studies of vortex flows pertinent to both aircraft and maritime applications. The studies also ranged from fundamental fluids investigations to flight test results, and significant results were contributed from a broad range of countries. The principal emphasis of this symposium was on "the understanding and prediction of separation-induced vortex flows and their effects on military vehicle performance, stability, control, and structural design loads." It was further observed by the program committee that "separation- induced vortex flows are an important part of the design and off-design performance of conventional fighter aircraft and new conventional or unconventional manned or unmanned advanced vehicle designs (UAVs, manned aircraft, missiles, space planes, ground-based vehicles, and ships)." The nine sessions addressed the following topics: vortical flows on wings and bodies, experimental techniques for vortical flows, numerical simulations of vortical flows, vortex stability and breakdown, vortex flows in maritime applications, vortex interactions and control, vortex dynamics, flight testing, and vehicle design. The purpose of this paper is to provide brief reviews of these papers along with some synthesizing perspectives toward future vortex flow research opportunities. The paper includes the symposium program. (15 refs.)

VORTEX BREAKDOWN↗
NASA NTRS1993

A hydrodynamic treatment of the tilted cold dark matter cosmological scenario

A standard hydrodynamic code coupled with a particle-mesh code is used to compute the evolution of a tilted cold dark matter (TCDM) model containing both baryonic matter and dark matter. Six baryonic species are followed, with allowance for both collisional and radiative ionization in every cell. The mean final Zel'dovich-Sunyaev y parameter is estimated to be (5.4 +/- 2.7) x 10 exp -7, below currently attainable observations, with an rms fluctuation of about (6.0 +/- 3.0) x 10 exp -7 on arcmin scales. The rate of galaxy formation peaks at a relatively late epoch (z is about 0.5). In the case of mass function, the smallest objects are stabilized against collapse by thermal energy: the mass-weighted mass spectrum peaks in the vicinity of 10 exp 9.1 solar masses, with a reasonable fit to the Schechter luminosity function if the baryon mass to blue light ratio is about 4. It is shown that a bias factor of 2 required for the model to be consistent with COBE DMR signals is probably a natural outcome in the present multiple component simulations.

Cen, Renyue↗
NASA NTRS1966

Breakup of Droplets in an Accelerating Gas Flow

A study of droplet breakup phenomena by an accelerating gas flow is described. The phenomena are similar to what propellant droplets experience when exposed to accelerating combustion gas flow in a rocket engine combustion zone. Groups of several dozen droplets in the 100-10 750-micron-diameter range were injected into a flowing inert gas in a transparent rectangular nozzle. Motion photography of the behavior of the droplets at various locations in the accelerating gas flow has supplied quantitative and qualitative data on the breakup phenomena which occur under conditions similar to those found in large rocket engine combustors. A blowgun injection device, used to inject very small amounts of liquid at velocities of several hundred feet per second into a moving gas stream, is described. The injection device was used to inject small amounts of liquid RP-1 and water into the gas stream at a velocity essentially equal to the gas velocity where the group of droplets was allowed to stabilize its formation in a constant area section before entering the convergent section of the transparent nozzle. Favorable comparison with the work of previous investigators who have used nonaccelerating gas flow is found with the data obtained from this study with accelerating gas flow. The criterion for the conditions of minimum severity required to produce shear-type droplet breakup in an accelerating gas flow is found to agree well with the criterion previously established at Rocketdyne for breakup in nonaccelerating flow. An extension of the theory of capillary surface wave effects during droplet breakup is also presented. Capillary surface waves propagating in the surface of the droplet, according to classical hydrodynamical laws, are considered. The waves propagate tangentially over the surface of the droplet from the forward stagnation point to the major diameter. Consideration of the effects of relative gas velocity on the amplitude growth of these waves allows conclusions to be made regarding rates of the droplet breakup processes and total time of the breakup process.

Dickerson, R. A.↗
DOE OSTI2025

Assessing the performance of MagLIF with 3D MHD simulations

The Magnetized Liner Inertial Fusion (MagLIF) experimental platform at Sandia National Laboratories has realized a number of recent improvements in electrical current and laser preheat coupling but fusion yields are below expectations, based on modeling with clean (that is, simulations with no interfacial instabilities and no mix) two-dimensional (2D) magneto-hydrodynamics (MHD) simulations, by a factor of 5 or more. However, magnetized liner implosions are known to produce helical magneto-Rayleigh–Taylor (MRT) modes and complex stagnation structures that cannot be directly modeled in 2D. This paper presents the results of 3D HYDRA MHD simulations, including helical MRT, showing that degradation from these instabilities can readily reproduce experimental yields, but it is difficult to simultaneously match the yield along with inferred fuel temperature, pressure, and burn history (assessed with x-rays), which are larger in the experiments considered here. Additional analysis methods and future experiments are proposed to help address the discrepancies. The 3D simulations also show, without substantive improvements to stability, changing the applied Bz or preheat is unlikely to increase performance of MagLIF to the same degree as clean 2D simulations. Finally, the first 3D HYDRA simulations with the Hall term show the ab initio production of helical MRT and produce a clear change in stagnation morphology compared to pre-seeded simulations without Hall. In spite of the differences, the simulations still produce comparable fusion performance but with longer, lower power, neutron yield history.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Initial conditions for simulations of beam physics in linear induction accelerators

Flash radiography of hydrodynamic experiments driven by high explosives is a well-known diagnostic technique in use at many laboratories. At Los Alamos, the DualAxis Radiographic Hydrodynamic Test (DARHT) facility two linear induction electron accelerators (LIAs) make the bremsstrahlung radiographic source spots for point projection radiographs from orthogonal views. A new LIA, called Scorpius, is presently under development to advance this technology. To better understand electron-beam physics in these LIAs, numerical simulations are frequently performed with the objective of improving the radiography. At Los Alamos we frequently use the TRAK ray-trace and LSP particle-in-cell (PIC) codes to simulate the injector, and the XTR and LAMDA envelope/centroid codes along with LSP to simulate transport of the accelerated beam through the LIAs. The LIA simulations need the injected beam parameters as initial conditions for calculating beam transport and stability. The determination of these initial conditions is the topic of this note.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Correct Initial Conditions for Simulations of Beam Physics in Linear Induction Accelerators

Flash radiography of hydrodynamic experiments driven by high explosives is a well-known diagnostic technique in use at many laboratories. At Los Alamos, the Dual Axis Radiographic Hydrodynamic Test (DARHT) facility two linear induction electron accelerators (LIAs) make the bremsstrahlung radiographic source spots for point projection radiographs from orthogonal views. A new LIA, called Scorpius, is presently under development to advance this technology. To better understand electron-beam physics in these LIAs, numerical simulations are frequently performed with the objective of improving the radiography. At Los Alamos we frequently use the TRAK ray-trace and LSP particle-in-cell (PIC) codes to simulate the injector, and the XTR and LAMDA envelope/centroid codes along with LSP to simulate transport of the accelerated beam through the LIAs. The LIA simulations need the injected beam parameters as initial conditions for calculating beam transport and stability. The determination of these initial conditions is the topic of this note.

43 PARTICLE ACCELERATORS↗
NASA NTRS1995

Wave Journal Bearing. Part 1: Analysis

A wave journal bearing concept features a waved inner bearing diameter of the non-rotating bearing side and it is an alternative to the plain journal bearing. The wave journal bearing has a significantly increased load capacity in comparison to the plain journal bearing operating at the same eccentricity. It also offers greater stability than the plain circular bearing under all operating conditions. The wave bearing's design is relatively simple and allows the shaft to rotate in either direction. Three wave bearings are sensitive to the direction of an applied stationary side load. Increasing the number of waves reduces the wave bearing's sensitivity to the direction of the applied load relative to the wave. However, the range in which the bearing performance can be varied decreases as the number of waves increases. Therefore, both the number and the amplitude of the waves must be properly selected to optimize the wave bearing design for a specific application. It is concluded that the stiffness of an air journal bearing, due to hydrodynamic effect, could be doubled and made to run stably by using a six or eight wave geometry with a wave amplitude approximately half of the bearing radial clearance.

Dimofte, Florin↗
DOE OSTI2022

Tracking the environmental impacts of ecological engineering on coastal wetlands with numerical modeling and remote sensing

Coastal wetlands are the most valuable ecosystems on the earth but facing severe degradation and losses owing to climate change and anthropogenic activities. Many ecological engineering projects (EEP) have been conducted to mitigate the degradation of coastal wetlands. However, the geomorphological impacts of EEP on coastal wetlands have not been well documented. In this study, a method employed a process-based hydrodynamic model and remote sensing (RS) was developed to evaluate the impacts of EEP on the geomorphological change of a prototype Ramsar site. Results demonstrated that RS has great potential in improving the quality of bathymetry data for the numerical model with a decrease of RMSE from 0.52 m to 0.3 m. It also showed good capacity in trend detection of geomorphological change spatially. Results showed the Chongming Dongtan wetland experienced erosion with an annual rate of -0.035 m/yr from 2013 to 2016 after the implementation of EEP. The deposition rate changed significantly in the area within 200 m of the EEP. It is found that the EEP modified the composition of vegetation, sediment transportation, as well as substrate stability, affecting the geomorphological change of coastal wetlands. It is suggested that the EEP with moderate anthropogenic disturbance is a direct and effective way to recover the coastal habitats for waterbirds. However, the modification of the coastal wetland ecosystem by EEP will lead to the potential vulnerability to global climate change. Therefore, how to mitigate the advantages and disadvantages of the EEP is needed to be further studied to find a more sustainable way for coastal management.

geomorphological change, coastal wetlands, Ecologi↗
DOE OSTI2025

Stabilizing dynamic subsea power cables using Bi-stable nonlinear energy sinks

This study investigates vibration mitigation of dynamic subsea cables through passive bi-stable nonlinear energy sinks (B-NESs). These devices suppress vibration energy in a broadband way, and can be regarded as extensions of classical linear tuned mass dampers (TMDs) which are narrowband devices. Through the open-source MoorDyn library, we simulated the vibrations of a vertical subsea cable equipped with a set of B-NESs. Multi-objective optimization was performed to detect the B-NES parameters for optimal mitigation of the cable vibrations. Advanced signal processing verified the efficacy of the optimized B-NESs not only to rapidly absorb and locally dissipate vibration energy, but also to nonlinearly scatter vibration energy from low to high frequencies within the cable itself. This last feature is especially beneficial for vibration mitigation of the undersea cable, as at higher frequencies the cable vibrations exhibit drastically reduced amplitudes and are more effectively dissipated by inherent structural damping and hydrodynamic radiation damping. This contrasts with traditional TMDs which can mitigate vibration only at a single frequency. Furthermore, our robustness study confirms the B-NES's effectiveness under even varying environmental conditions. Overall, the B-NES's capacity for broadband vibration mitigation renders it a promising retrofit solution for improving the performance and operational safety of dynamic power cables in offshore wind farms and other marine applications.

17 WIND ENERGY↗
DOE OSTI2022

Optimum Injector Parameters for Thermoacoustic Stability in a Multi-Nozzle Can Combustion System

Abstract High-frequency transverse instabilities are an important concern in can combustor configurations. In these configurations which are typically operated with multiple injectors around a central injector, each injector is subjected to different parts of the acoustic mode shape and thus respond differently for the same instability mode. Recent work by the author has modeled the response of premixed flames to excitation by natural high-frequency transverse modes in a can combustor both in the center and outer nozzles. The stability of these acoustically non-compact flames was assessed using the Rayleigh criterion (Rayleigh Integral denoted as RI) and not the overall unsteady heat release as is the case for compact flames. Several key control parameters were studied, namely — flame angle, swirling strength, nozzle location. For non-axisymmetric modes such as the commonly occurring 1-T mode, both radial and azimuthal offsets of the nozzle location affected stability. The framework was applied to an optimization study to identify the optimal combination of parameters that minimizes RI for the different nozzles in the multi-nozzle system. In this study, a N-around-1 configuration was studied, and the results indicated that the different nozzles needed to be operated at different flame angles and swirl numbers to result in an overall minimum RI. However, the specific response of the different injectors was not considered. The helical mode distribution at each injector varies as we azimuthally go around the combustor’s injector distribution and thus the most amplified mode and the resulting flame response would be different. To minimize RI, it is important to determine the injector configurations that result in a hydrodynamic profile that minimizes the individual RI for each nozzle. The resulting relationship between the injector’s flow and local hydrodynamics can then be used in a hydrodynamics study of an individual injector so that the most optimal injector is chosen depending on its location in the combustor dump plane.

Acharya, Vishal↗
DOE OSTI2020

Applying the Gyrokinetic Formulation of Magnetized Plasma Dynamics to Z-pinch plasmas

This project adapts and applies the gyrokinetic Eulerian code COGENT to an emerging area of highly-magnetized Z-pinch plasma systems. Simulation efforts for these plasmas currently use either magneto-hydrodynamic (MHD) fluid codes, which suffer from fidelity being restricted to narrow plasma conditions, or fully kinetic particle-in-cell (PIC) methods, which suffer from the run-time needed to resolve the very small spatial and temporal scales required for the plasma conditions. The progress with achieving detailed theoretical understanding of Z-pinch plasma systems can be greatly expedited using some combination of gyrokinetic and drift-ordered MHD models, developed in the tokamak community and implemented in the COGENT code. These formulations are applicable to a much larger parameter space than standard MHD models, while providing a substantial speed-up in run-time over fully kinetic codes. In particular, the gyrokinetic formalism is successfully applied to a flow-stabilized Z pinch (FSZP) system – a promising fusion concept where a sheared axial flow is used to provide stability against large-scale ideal-MHD modes. Results of gyrokinetic simulations with COGENT agree well with those from fully kinetic simulations, while requiring ~500x less run-time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

Collisions of giant stars with compact objects - Hydrodynamical calculations

Smooth particle hydrodynamics are used here to model encounters between an 0.8 solar mass giant star and a 1.4 solar mass compact object on a parabolic orbit. It is found that all encounters with periastron distance r(p) less than about 2.5 stellar radii R(G) lead to significant disruption of the stellar envelope, including some mass loss. When r(p)/R(G) is less than about 0.5, the envelope is completely destroyed during the collision. About 40 percent of the gas escapes, while the rest forms a massive disk around the compact object, leaving behind the bare stellar core on a highly eccentric orbit. Subsequent close passages lead to continuous extraction of gas from the disk at a large rate, and the binary orbit may eventually stabilize while still retaining a large eccentricity. It is suggested that many globular cluster pulsars may have been spun up by accretion from a massive disk rather than from a binary companion, thereby providing a possible solution to the birthrate problem.

Rasio, Frederic A.↗
NASA NTRS1954

Hydrodynamic Investigation of the the Take-Off Characteristics of a 1/10-Scale Dynamic Model of the Convair XF2Y-1 Airplane

An investigation was made of the take-off characteristics of a 1/10-scale dynamic model of the Convair XF2Y-1 airplane. This airplane is a water-based, jet-propelled, delta-wing fighter incorporating a hydro-ski landing gear. Tests were made with the original configuration, with the beaching wheels removed, and with the wheels installed and fairings added in front of the wheels. Each configuration was tested at weight and balance conditions simulating 17,000 pounds gross weight with the moment due t o 7,600 pounds of thrust, 17,300 pounds gross weight with a 9,500-pound thrust condition, and 23,000 pounds gross weight with a 9,300-pound thrust condition. Constant-speed runs were made at various elevon settings and vertical ski-strut positions; and trim, rise, and resistance were measured. Accelerated runs were made with controlled elevons and scale shock struts which could be extended as desired, and the longitudinal stability and spray characteristics were observed and photographed.

McBridge, Ellis E.↗
NASA NTRSDate not supplied

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

The linear amplification of modal disturbances that lead to boundary-layer transition in two-dimensional/axisymmetric hypersonic configurations is strongly reduced by the presence of a blunt nosetip, and the mechanisms underlying the observed onset of transition over the cone frustum are currently unknown. Linear nonmodal analysis has shown that both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification for moderate to large nosetip bluntness. The present study extends the previous linear analysis by including the nonlinear effects. Specifically, the perturbation form of the 2D, harmonic Navier-Stokes equations (HNSE) are solved with a fully implicit formulation and the Newton-Raphson method. The increased number of degrees of freedom for the nonlinear system presents difficulties for solution strategies based on direct solution of the linearized system. Such difficulties are overcome by using the GMRES iterative method with a preconditioner corresponding to a simplified Jacobian without the cross derivative terms. The HNSE solver is verified by comparing with nonlinear parabolized stability equation (NPSE) results for the nonlinear evolution of planar waves in an incompressible Blasius boundary layer and in a Mach 6 flow over a blunt cone. Finally, nonlinear nonmodal results are presented for planar traveling disturbances over the blunt cone. The nonmodal analysis demonstrates that entropy-layer disturbances generated close to the nose tip can seed the amplification of higher frequency Mack’s second-mode instabilities further downstream.

boundary layer transition↗
NASA NTRS1991

Two-dimensional hydrodynamic calculations of the nonlinear development of the Goldreich-Schubert-Fricke instability in a rotating annulus

Two-dimensional nonlinear hydrodynamic calculations are presented which may help assess the effectiveness of the instability in transporting angular momentum in the equatorial zones of stars and planets which are stably stratified with respect to convection. The calculations were made by numerically integrating the 2D axisymmetric Navier-Stokes equations, including viscosity and heat conduction. The instability was followed into the nonlinear regime. The maximum rms velocity amplitude was found to correlate well with the product of the linear growth rate and radial length scale of the instability, consistent with the idea that the instability grows to an amplitude such that an eddy turnover time becomes equal to the growth time defined by the inverse of the growth rate. The time scale for angular momentum to be redistributed to a state of marginal stability was consistent with this picture. The results suggest that in physical situations a state of marginal stability will be maintained, since departures from such a state will be rapidly corrected.

Korycansky, D. G.↗