Search NASA⌕ Search

SEARCH · Search NASA

Results for “Main”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Apollo 14 mission: Inability to disconnect main bus A

During entry, the Apollo 14 spacecraft busses should have de-energized when the main bus-tie motor switches were switched to the off position. One motor switch did not transfer and main bus A remained energized until the battery bus-tie circuit breakers were opened after landing. Analysis revealed that residual catalyst caused the terminal pin seals to revert to a gummy state. Resulting reversion products then migrated to the motor commutator and caused brush degradation, increased and erratic commutator resistance, and reduced motor torque. The motor stalled when available motor torque was reduced below that required to drive through the maximum torque point of the switch.

Source record↗

Apollo 16 mission. Holes in canopy of main parachute

The occurrence of an anomaly during the Apollo 16 flight is discussed. The canopy of one of the recovered main parachutes had numerous small burn holes. An analysis of events following main parachute deployment which could cause the anomaly is presented. It is concluded that the burn holes in the parachute were the result of oxidizer being expelled when the plus-yaw engines were fired as the spacecraft was in the final phase of descent.

Source record↗

Turbopump configuration selection for the Space Shuttle main engine

Studies to define the optimum turbopump configurations for the Space Shuttle propulsion system are reported. For each propellant, two turbopumps - one low-pressure and one high-pressure - are needed to generate the high discharge pressures required for engine operation. The optimization of the four pumps resulted in the selection of an axial inducer type for both low-pressure pumps and in a three-stage centrifugal pump for the high-pressure hydrogen turbopump; meanwhile the oxygen pump features a double inlet main impeller. This impeller feeds the thrust chamber injector, as well as a preburner pump, which boosts the main impeller discharge pressure to the required preburner pressure. The interaction between engine performance and obtainable turbopump performance is discussed, and the reasons for the final selection of the turbine and pump types are presented.

Rothe, K.↗

Investigation of the Centaur boost pump overspeed condition at main engine shutdown on the Titan Centaur TC-2 flight

An investigation was conducted to evaluate a potential boost pump overspeed condition which could exist on the Titan/Centaur launch vehicle after main engine shut-off. Preliminary analyses indicated that the acceleration imparted to the unloaded boost pump-turbine assembly, caused by purging residual hydrogen peroxide from the turbine supply lines, could result in a pump-turbine overspeed. Previous test experience indicated that turbine damage occurs at speeds in excess of 75,000 rpm. Detailed theoretical analyses, in conjunction with pump tests, were conducted to establish the maximum pump-turbine speed at main engine shut-off. The analyses predicted a maximum speed of 68,000 rpm. Testing showed the pump-turbine speed to be 66,700 rpm in the overspeed condition. Inasmuch as both the analysis and tests showed the overspeed to be sufficiently less than the speed at which damage could occur, it was concluded that no corrective action would be required for the launch vehicle.

Baud, K. W.↗

F sub 2 peak electron densities in the main trough region of the ionosphere

A study of the main trough in the F2 region was made using observations from Alouette I and II. Parameters needed to predict the occurrence of the trough were determined from the many observations. These parameters were used to develop a modification factor for use with C.E.I.R. model of predicted MmF2. This modification factor reduced the C.E.I.R. model predicted NmF2 to more representative values of MmF2 in the main trough region.

Halcrow, B. W.↗

Space shuttle three main engine return to launch site abort

A Return-to-Launch-Site (RTLS) abort with three Space Shuttle Main Engines (SSME) operational was examined. The results are trajectories and main engine cutoff conditions that are approximately the same as for a two SSME case. Requiring the three SSME solution to match the two SSME abort eliminates additional crew training and is accomplished with negligible software impact.

Carter, J. F.↗

Design of the HEAO main bus shunt regulator

The High Energy Astronomy Observatory (HEAO) is being built for NASA by an American company. The general requirements concerning the HEAO main bus regulator are examined. The bus regulated voltage is 33 V, the maximum shunt current is 45 A, and the regulator output impedance is to be less than 0.5 Ohm from dc to 100 kHz. Loop gain design considerations for the main bus regulator are discussed and a description is given of the general device configuration. Attention is also given to regulator loop design and performance.

Middlebrook, R. D.↗

Space Shuttle Main Engine

Significant features of the Space Shuttle Main Engine (SSME) include a staged combustion power cycle, high area ratio nozzle expansion, throttling capability, and a computer operated control system. These main design features are discussed along with development test results.

Thompson, J. R., Jr.↗

Booster engines derived from the Space Shuttle Main Engine

Current vehicle studies of post-Space Shuttle vehicles have identified the potential need for a high-pressure booster engine using liquid oxygen/hydrocarbon fuel (RP-1) as propellants. Recent studies of the possibility of using Space Shuttle Main Engine (SSME) components for a high pressure LOX/RP-1 engine have resulted in several engine configurations which are based largely on SSME components. The current SSME thrust chamber is regeneratively cooled with hydrogen using a relatively low percentage of the total hydrogen flow. For a LOX/RP-1 application the SSME thrust chamber can be run at high pressures and be cooled with a relatively low hydrogen flow. In addition, the SSME oxygen pump, valves, and main injector components may be utilized for the booster engine. By using a majority of the current SSME engine components for the LOX/RE-1 booster engine, engine development time and cost can be significantly reduced compared to the development of a new engine.

Sobin, A. J.↗

Preflight status of the External Tank portion of the Space Shuttle Main Propulsion System

The development progress of the External Tank (ET) of the Shuttle Main Propulsion System (MPS) is described. 87% of ET propulsion components have satisfactorily completed qualification tests in preparation for the first Shuttle flight and their performance has been verified in the Main Propulsion Test Article (MPTA) firings of up to 100 seconds duration. The design changes in the LH2 tank pressurant diffuser, the LO2 feed system, and the ground test LO2 tank are discussed. Propellant loading information from MPTA tests may be used to predict loading operations and performance at KSC and VAFB, while ullage pressure profiles and boil-off rates during loading, chilldown rates, and final bulk density data have been obtained with geyser suppression evaluated and loading procedures established and verified. The MPTA test experience provided data to evaluate pressurization system and ET to Orbiter interface propellant performance noting thus that the fluid interface requirements will be satisfied for the first Shuttle flight. The Intertank inerting system was found to be effective in minimizing hazardous gas mixtures and full scale separation tests of the ET to Ground Umbilical Carrier Plate system were successfully completed.

Norquist, L.↗

Electrodeposition applications for the Space Shuttle Main Engine

Electrodeposition processes play a key role in the fabrication and in-service performance of the Space Shuttle Main Engine. Applications range from the electroforming of the main combustion chamber to the deposition of high-purity copper or gold for hydrogen embrittlement protection of susceptible materials of construction, or nickel for mechanical protection of foam insulated propellant ducts. Techniques for controlling electrolyte purity, verification of deposit integrity, and deposit profile and thickness are reported. The use of in-situ techniques (cell-plating) for localized plating and repair of damaged substrate materials are summarized.

Otousa, J. E.↗

Stellar evolution from the zero-age main sequence

A consistent set of 247 evolutionary sequences extending from the ZAMS to the red-giant branch is presented for Y from 0.10 to 0.40, Z from 0.00001 to 0.10, and masses of 0.55 to 6.90 solar masses. Each sequence is started from a homogeneous ZAMS model, and almost all are evolved to the base of the red-giant branch. It is shown that: (1) the relative position of the main sequence can be determined as a function of composition; (2) theoretical luminosity functions can be derived from the relative evolutionary time scales; (3) a dip in luminosity sometimes occurs at the base of the red-giant branch and is most pronounced at larger Z values; (4) metal-poor stars evolve farther up along the main sequence before turning off toward the red-giant branch; and (5) the onset of helium burning halts the evolution across the Hertzsprung gap for the most massive and most metal-poor models, so that the star remains blue during its phase of core-helium burning.

Mengel, J. G.↗

Space Shuttle Main Engine development /May 1980/

The Space Shuttle Main Engine is the most advanced liquid propellant rocket engine ever developed. During the last year, significant progess has been made toward the identification and solution of several design weaknesses. The initial two test series to certify the engine's readiness for manned flight have been completed, and additional test series are in progress. Operation of the total propulsion system has been demonstrated by a successful series of flight-simulation tests using the three-engine cluster Main Propulsion Test Article. The first set of flight engines has been acceptance tested for use in Shuttle Orbiter 102 (Columbia) for the first manned orbital flight in late 1980 or early 1981. Engine development is continuing with initial demonstrations of full-power level (109%) operation capability.

Sanchini, D. J.↗

Compensating linkage for main rotor control

A compensating linkage for the rotor control system on rotary wing aircraft is described. The main rotor and transmission are isolated from the airframe structure by clastic suspension. The compensating linkage prevents unwanted signal inputs to the rotor control system caused by relative motion of the airframe structure and the main rotor and transmission.

Jeffery, P. A. E.↗

Total main rotor isolation system analysis

Requirements, preliminary design, and verification procedures for a total main rotor isolation system at n/rev are presented. The fuselage is isolated from the vibration inducing main rotor at one frequency in all degrees of freedom by four antiresonant isolation units. Effects of parametric variations on isolation system performance are evaluated.

Sankewitsch, V.↗

Space shuttle main engine: Hydraulic system

The hydraulic actuation system of the space shuttle main engine is discussed. The system consists of five electrohydraulic actuators and a single engine filter used to control the five different propellant valves, which in turn control thrust and mixture ratio of the space shuttle main engine. The hydraulic actuation system provides this control with a precision of 98.7 percent or an error in position no greater than 1.3 percent of full scale rotational travel for critical positions.

Geller, G.↗

Observations of normal main-sequence and giant B stars

When interpreting the continuous and line spectra of B stars, it is helpful to think in terms of a model consisting of a photosphere and a mantle which is the outer part of the atmosphere where the effects of nonradiative heating are seen. A survey of the spectra of these stars shows that conditions in the photosphere determine most of what is seen, and in the case of most B stars, the presence of the mantle can be detected only by a special effort. The shape of the visible continuum spectrum and the shape and absolute value of the UV continuous spectrum as determined from low resolution spectra are discussed. Effective temperature for B stars in the main sequence, including corrections for interstellar extinction and bolometric corrections are explored. The major constituents of B-type spectra, variation of the strength of line along the main sequence band, the UV spectra, UV line blocking, intrinsic colors, and variations in light and spectra are also examined.

Source record↗

Experimental measurements of the Space Shuttle main engine fuel and oxygen turbopump vibration characteristics

The vibration characteristics of the SSME (Space Shuttle main engine) are dealt with. The Space Shuttle engine consists of a main rocket nozzle and attached to it are high pressure fuel and oxygen pumps. Various vibration problems have been encountered with both the hydrogen and oxygen pumps. The vibration spectrum of the hydrogen and oxygen pumps has been analyzed by various techniques using synchronous tracking filters and FFT analyzers. The experimental data has been correlated to theoretical predictions of resonance frequencies.

Gunter, E. J.↗