Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗

Dual Microstructure Heat Treatment of a Nickel-Base Disk Alloy Assessed

Gas turbine engines for future subsonic aircraft will require nickel-base disk alloys that can be used at temperatures in excess of 1300 F. Smaller turbine engines, with higher rotational speeds, also require disk alloys with high strength. To address these challenges, NASA funded a series of disk programs in the 1990's. Under these initiatives, Honeywell and Allison focused their attention on Alloy 10, a high-strength, nickel-base disk alloy developed by Honeywell for application in the small turbine engines used in regional jet aircraft. Since tensile, creep, and fatigue properties are strongly influenced by alloy grain size, the effect of heat treatment on grain size and the attendant properties were studied in detail. It was observed that a fine grain microstructure offered the best tensile and fatigue properties, whereas a coarse grain microstructure offered the best creep resistance at high temperatures. Therefore, a disk with a dual microstructure, consisting of a fine-grained bore and a coarse-grained rim, should have a high potential for optimal performance. Under NASA's Ultra-Safe Propulsion Project and Ultra-Efficient Engine Technology (UEET) Program, a disk program was initiated at the NASA Glenn Research Center to assess the feasibility of using Alloy 10 to produce a dual-microstructure disk. The objectives of this program were twofold. First, existing dual-microstructure heat treatment (DMHT) technology would be applied and refined as necessary for Alloy 10 to yield the desired grain structure in full-scale forgings appropriate for use in regional gas turbine engines. Second, key mechanical properties from the bore and rim of a DMHT Alloy 10 disk would be measured and compared with conventional heat treatments to assess the benefits of DMHT technology. At Wyman Gordon and Honeywell, an active-cooling DMHT process was used to convert four full-scale Alloy 10 disks to a dual-grain microstructure. The resulting microstructures are illustrated in the photomicrographs. The fine grain size in the bore can be contrasted with the coarse grain size in the rim. Testing (at NASA Glenn) of coupons machined from these disks showed that the DMHT approach did indeed produce a high-strength, fatigue resistant bore and a creep-resistant rim. This combination of properties was previously unobtainable using conventional heat treatments, which produced disks with a uniform grain size. Future plans are in place to spin test a DMHT disk under the Ultra Safe Propulsion Project to assess the viability of this technology at the component level. This testing will include measurements of disk growth at a high temperature as well as the determination of burst speed at an intermediate temperature.

Gayda, John↗

Microstructure Modeling of Third Generation Disk Alloys

The objective of this program was to model, validate, and predict the precipitation microstructure evolution, using PrecipiCalc (QuesTek Innovations LLC) software, for 3rd generation Ni-based gas turbine disc superalloys during processing and service, with a set of logical and consistent experiments and characterizations. Furthermore, within this program, the originally research-oriented microstructure simulation tool was to be further improved and implemented to be a useful and user-friendly engineering tool. In this report, the key accomplishments achieved during the third year (2009) of the program are summarized. The activities of this year included: Further development of multistep precipitation simulation framework for gamma prime microstructure evolution during heat treatment; Calibration and validation of gamma prime microstructure modeling with supersolvus heat treated LSHR; Modeling of the microstructure evolution of the minor phases, particularly carbides, during isothermal aging, representing the long term microstructure stability during thermal exposure; and the implementation of software tools. During the research and development efforts to extend the precipitation microstructure modeling and prediction capability in this 3-year program, we identified a hurdle, related to slow gamma prime coarsening rate, with no satisfactory scientific explanation currently available. It is desirable to raise this issue to the Ni-based superalloys research community, with hope that in future there will be a mechanistic understanding and physics-based treatment to overcome the hurdle. In the mean time, an empirical correction factor was developed in this modeling effort to capture the experimental observations.

Jou, Herng-Jeng↗

Microstructure Quantification and Random Forest Regression Models for Li4Ti5O12–Ni Property Prediction

All-solid-state structural lithium-ion batteries are sought to enable all-electric propulsion in next generation aerospace concepts through improved safety and systems level weight savings. In this work, the influence of processing conditions on microstructural evolution was evaluated for anode composites of strain-free Li4Ti5O12 and metallic nickel current collector. Beyond size distributions, this study explored methods of quantifying microstructural features that describe changes in the spatial distribution and coalescence of nickel particles as a function of sample composition and sintering conditions. Processing-microstructure-property relationships were described by microstructure quantifiers including nickel particle count per area, nearest neighbor distance distribution, and edge-to-edge distance distribution. Machine learning methods were applied to compare the relative influence of processing conditions and microstructural features on electrical conductivity and mechanical strength to optimize for simultaneous energy storage and load bearing performance. Insights gained from this work inform future evaluation of alternative energy storage materials and microstructures for multifunctional performance, and generation of microstructural descriptors strengthens modeling across length scales.

anode↗

Ultrasonic Characterization of Cast Austenitic Stainless Steel Microstructure: Discrimination between Equiaxed- and Columnar-Grain Material – An Interim Study

Ultrasonic nondestructive evaluation (NDE) and inspection of cast austenitic stainless steel (CASS) components used in the nuclear power industry is neither as effective nor reliable as is needed due to detrimental effects upon the interrogating ultrasonic beam and interference from ultrasonic backscatter. The root cause is the coarse-grain microstructure inherent to this class of materials. Some ultrasonic techniques perform better for particular microstructural classifications and this has led to the hypothesis that an ultrasonic inspection can be optimized for a particular microstructural class, if a technique exists to reliably classify the microstructure for feedback to the inspection. This document summarizes scoping experiments of in-situ ultrasonic methods for classification and/or characterization of the material microstructures in CASS components from the outside surface of a pipe. The focus of this study was to evaluate ultrasonic methods and provide an interim report that documents results and technical progress. An initial set of experiments were performed to test the hypothesis that in-service characterization of cast austenitic stainless steel (CASS) is feasible, and that, if reliably performed, such data would provide real-time feedback to optimize in-service inspections in the field. With this objective in mind, measurements for the experiment were restricted to techniques that should be robust if carried forward to eventual field implementation. Two parameters were investigated for their ability to discriminate between different microstructures in CASS components. The first parameter was a time-of-flight ratio of a normal incidence shear wave to that of a normal incidence longitudinal wave (TOFRSL). The ratio removed dependency on component thickness which may not be accurately reported in the field. The second parameter was longitudinal wave attenuation. The selected CASS specimens provided five equiaxed-grain material samples and five columnar-grain material samples for a two-class discrimination problem. Qualitative TOFRSL estimates and a threshold algorithm classified all 10 material samples correctly and indicated a reliable and robust technique. Qualitative longitudinal wave attenuation estimates and a threshold algorithm also classified all 10 materials samples correctly; however, the technique was not as robust as TOFRSL. The experiments provided promising results and demonstrated that good potential exists for future development of techniques to implement real-time classification of CASS material. However, the reported measurements need to be substantiated with measurements on additional specimens.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

EBSD Analysis of Relationship Between Microstructural Features and Toughness of a Medium-Carbon Quenching and Partitioning Bainitic Steel

A multiphase microstructure of bainite, martensite and retained austenite in a 0.3C bainitic steel was obtained by a novel bainite isothermal transformation plus quenching and partitioning (B-QP) process. The correlations between microstructural features and toughness were investigated by electron backscatter diffraction (EBSD), and the results showed that the multiphase microstructure containing approximately 50% bainite exhibits higher strength (1617 MPa), greater elongation (18.6%) and greater impact toughness (103 J) than the full martensite. The EBSD analysis indicated that the multiphase microstructure with a smaller average local misorientation (1.22°) has a lower inner stress concentration possibility and that the first formed bainitic ferrite plates in the multiphase microstructure can refine subsequently generated packets and blocks. The corresponding packet and block average size decrease from 11.9 and 2.3 to 8.4 and 1.6 μm, respectively. A boundary misorientation analysis indicated that the multiphase microstructure has a higher percentage of high-angle boundaries (67.1%) than the full martensite (57.9%) because of the larger numbers and smaller sizes of packets and blocks. The packet boundary obstructs crack propagation more effectively than the block boundary.

36 MATERIALS SCIENCE↗

Microstructure and Temperature Dependent Indentation Response of Additively Manufactured Precipitation-Strengthened Al 0.3 Ti 0.2 Co 0.7 CrFeNi 1.7 High Entropy Alloy

The temperature-dependent [from room temperature (RT) to 500°C] nanoindentation behavior of a precipitation-strengthened Al 0.3 Ti 0.2 Co 0.7 CrFeNi 1.7 high-entropy alloy (HEA) processed via two different additive manufacturing (AM) techniques was investigated in the as-deposited and annealed conditions. The hierarchically heterogeneous microstructures were achieved via simple one-step annealing treatments, exploiting the residual stresses in the AM-processed HEA to partially recrystallize the microstructure, performed remarkably better than the nearly homogeneous microstructures in the as-deposited state. Further, the one-step annealed conditions revealed < 6.6% reduction in hardness values at 500°C compared to RT, while the as-deposited conditions showed a > 18% reduction in the hardness. The one-step annealed conditions also exhibited significantly higher hardness than the as-deposited conditions owing to their L1 2 -strengthened FCC microstructures. Furthermore, serrated yielding or the Portevin-Le Chatlier effect indicative of microstructural instability was observed during nanoindentation deformation (at 500°C) for the as-deposited conditions but not for the one-step annealed conditions. This, therefore, signifies the robustness of the hierarchically heterogeneous microstructures at elevated temperatures presenting a strong avenue for tuning the HEAs for future nuclear reactor applications.

36 MATERIALS SCIENCE↗

Automated Grain Boundary (GB) Segmentation and Microstructural Analysis in 347H Stainless Steel Using Deep Learning and Multimodal Microscopy

Austenitic 347H stainless steel offers superior mechanical properties and corrosion resistance required for extreme operating conditions such as high temperature. The change in microstructure due to composition and process variations is expected to impact material properties. Identifying microstructural features such as grain boundaries thus becomes an important task in the process-microstructure-properties loop. Applying convolutional neural network (CNN)-based deep learning models is a powerful technique to detect features from material micrographs in an automated manner. In contrast to microstructural classification, supervised CNN models for segmentation tasks require pixel-wise annotation labels. However, manual labeling of the images for the segmentation task poses a major bottleneck for generating training data and labels in a reliable and reproducible way within a reasonable timeframe. Microstructural characterization especially needs to be expedited for faster material discovery by changing alloy compositions. Here, in this study, we attempt to overcome such limitations by utilizing multimodal microscopy to generate labels directly instead of manual labeling. We combine scanning electron microscopy images of 347H stainless steel as training data and electron backscatter diffraction micrographs as pixel-wise labels for grain boundary detection as a semantic segmentation task. The viability of our method is evaluated by considering a set of deep CNN architectures. We demonstrate that despite producing instrumentation drift during data collection between two modes of microscopy, this method performs comparably to similar segmentation tasks that used manual labeling. Additionally, we find that naïve pixel-wise segmentation results in small gaps and missing boundaries in the predicted grain boundary map. By incorporating topological information during model training, the connectivity of the grain boundary network and segmentation performance is improved. Finally, our approach is validated by accurate computation on downstream tasks of predicting the underlying grain morphology distributions which are the ultimate quantities of interest for microstructural characterization.

36 MATERIALS SCIENCE↗

Computing diffraction patterns of microstructures from phase-field simulations

The diffraction pattern of a material contains information not only on the crystal structures of its constituting phases, but also on its mesoscale spatial distributions of phases, grains, and ferroelastic, ferroelectric, and ferromagnetic domains. While diffraction patterns from experiments such as X-ray diffraction are presented in the reciprocal or Fourier space, mesoscale microstructure models such as the phase-field method naturally produce real-space images of spatial distribution of chemical composition, structural, and ferroic domains. Although one could rather readily compute the Fourier amplitudes of chemical and structural domain distributions generated by mesoscale simulations, they only contain information about the length scale and alignment of the real-space chemical and structure domains. Therefore, a direct comparison between diffraction experiments and mesoscale microstructure simulations is not possible. Here, we develop a theoretical approach to directly compute the crystal diffraction patterns of microstructures predicted by phase-field simulations. In particular, we consider five representative examples of microstructure patterns involving purely compositional domains, a single pair of tetragonal twin structures, multiple twin variants in a hexagonal system, ferroelectric polar vortices, and polycrystalline grains. The results are compared with previous experimental observations as well as X-ray diffraction experiments performed in the present study. Furthermore, the theoretical framework allows one to directly connect material microstructures and diffraction patterns predicted from phase-field simulations and the corresponding diffraction patterns from experiments, and thus providing guidance to experimental diffraction characterization and interpretation of microstructures.

36 MATERIALS SCIENCE↗

Geometry-independent microstructure optimization for electron beam powder bed fusion additive manufacturing

The ability to manipulate the formation of microstructure is one of the potential advantages of additive manufacturing. Yet, the additive manufacturing process is riddled with complex interactions between processing parameters, geometry, and spot melting sequence which makes the task of controlling microstructure challenging. This paper proposes a method to solve the microstructure texture optimization problem by leveraging established optimization techniques and increasingly fast and accurate analytical heat transfer models. Respectively, we apply two different optimization algorithms, genetic algorithm and concurrent greedy line search, in order to induce arbitrarily shaped microstructure regions and we use a heat transfer model to evaluate the fitness of solutions in an iterative approach that is far more efficient than pure trial and error. The objective of the optimization algorithm is to control local thermal conditions – hence microstructure formation – during the melting process by manipulating the order and the dwell time of all the points of the infill pattern sequence. We then analyze the optimized sequence to determine important path characteristics that affect the microstructure formation. Through examples, we show that relative order and frequency, as measured by weighted average and variance of spot order, are important factors that influence the final characteristics.

36 MATERIALS SCIENCE↗

Leveraging the digital thread for physics-based prediction of microstructure heterogeneity in additively manufactured parts

A major limitation of additive manufacturing (AM) processes is that local conditions of material deposition frequently lead to unintentional heterogeneities in microstructure and properties within a single component, despite nominally uniform process conditions. Up to now, there has been no way to a priori determine the distribution of these heterogeneities, requiring expensive trial-and-error approaches to fabrication, testing, and characterization. Here, a physics-based framework for creating a digital representation of the laser powder bed fusion (PBF) process is proposed to predict the variation in solidification behavior that leads to heterogeneous microstructures in an as-built part. By leveraging in situ process data stored in the part’s digital thread, the scan path and process parameters were input into a heat transfer model which predicted solidification data at the melt pool scale. A two-step unsupervised clustering algorithm was used to first cluster the local solidification conditions (12.5µm 3 voxels) and then to cluster the regional behavior on the scale of multiple scan passes and print layers (250µm 3 super-voxels). This process was used to identify regions with similar solidification characteristics for multiple locations in a Stainless Steel 316-L component. The corresponding as-built part was sectioned and characterized using electron backscatter diffraction (EBSD). Quantitative analysis of the pole figures confirmed that the predicted regions of heterogeneity in the solidification conditions corresponded with differences in the observed microstructure. In conclusion, this work shows a viable path for estimating the microstructural heterogeneity for additively manufactured parts to either limit microstructural variation throughout a part or to enable functionality-based variation of the microstructure.

36 MATERIALS SCIENCE↗

A microstructure-guided constitutive modeling approach for random heterogeneous materials: Application to structural binders

This paper presents a microstructure-guided modeling approach to predict the effective elastic response of heterogeneous materials, and demonstrates its application toward two highly heterogeneous, uncon- ventional structural binders, i.e., iron carbonate and fly ash geopolymer. Microstructural information from synchrotron X-ray tomography (XRT) and intrinsic elastic properties of component solid phases from statistical nanoindentation are used as the primary inputs. The virtual periodic 3D microstructure reconstructed using XRT, along with periodic boundary conditions is used as a basis for strain- controlled numerical simulation scheme in the linear elastic range to predict the elastic modulus as well as the stresses in the microstructural phases. The elastic modulus of the composite material predicted from the microstructure-based constitutive modeling approach correlates very well with experimental measurements for both the materials considered. This technique efficiently links the microstructure to mechanical properties of interest and helps develop material design guidelines for novel heterogeneous composites

36 MATERIALS SCIENCE↗

Mesoscale modeling and semi-analytical approach for the microstructure-aware effective thermal conductivity of porous polygranular materials

Here we established a comprehensive modeling approach for investigating the microstructure-aware effective thermal conductivity ($κ_{eff}$) for porous microstructures containing solid particles and gaseous pores. Our approach combines the mesoscale computational modeling framework and the semi-analytical method, allowing for efficient prediction of $κ_{eff}$ for realistic porous microstructures, while considering complicated microstructural thermal conduction pathways effectively in the prediction. We used the diffuse-interface mesoscale computational model to generate extensive simulated $κ_{eff}$ data for realistic digital representations of microstructures with wide ranges of porosity ($f_p$), thermal conductivity of the gas phase ($κ_g$), and thermal conductivity of the solid phase ($κ_s$). From the simulated data, we identified two property variation regimes for $κ_{eff}$: (1) a slow $κ_{eff}$ increase for $κ_s ~ κ_g$; and (2) a faster $κ_{eff}$ increase for $κ_s \gg κ_g$. To capture the key features of the relationship between the microstructure and $κ_{eff}$, we derived a semi-analytical model by introducing structure and intensification factors. The two new factors incorporate the calibrated effective contribution of the solid volume with $κ_s$ and additional interfacial effects into the prediction of $κ_{eff}$, respectively, allowing for consideration of parallel, serial, and interfacial conduction mechanisms effectively. Using the selected simulation data, we quantified key model parameters within the semi-analytical model and verified that the parameterized model exhibits excellent agreement with simulated $κ_{eff}$ for the entire range of the parameter space.

36 MATERIALS SCIENCE↗

Inverse design of hypoeutectoid pearlite steel microstructures using a deep learning and genetic algorithm optimization framework

Goal-oriented microstructure design in metallic materials is a challenging task due to complex structure-property relationships. Traditional experimental and computational approaches are time-intensive and economically inefficient, limiting their applicability for large-scale design space exploration. Here, in this work, we propose an end-to-end framework that integrates deep learning models with genetic optimization to design microstructures with targeted mechanical properties. Deep learning models enable accurate forward design, while their integration with genetic optimization enables efficient inverse design within a few hours, compared to days or weeks using conventional finite element simulations. The framework combines experimental characterization and finite element modeling to analyze the influence of microstructural features on the mechanical behavior of hypoeutectoid steels. Data from both experiments and simulations are used to train the deep learning models. To demonstrate its effectiveness, we apply the framework to 0.63% carbon steel with proeutectoid ferrite and pearlite phases, commonly used in industrial applications. In this study, 2D microstructures were used for modeling, selected primarily for computational efficiency and to establish proof of concept. The framework successfully optimizes microstructures for targeted yield strength, ultimate strength, and stress concentration factors while significantly reducing computational time. Beyond hypoeutectoid steels, this scalable framework can be extended to other material systems and integrated with additive manufacturing, offering an efficient approach for accelerating microstructure design for specific engineering applications.

ConvLSTM↗

Microstructural diversity and digestion yields of select bituminous and subbituminous coals as raw material candidates for carbon fiber precursor production

Here, this work investigates the use of coals as raw materials for carbon fiber precursor production as a new alternative to coal utilization. Coal being a highly complex and heterogeneous material with different macerals and minerals complicates this task. Extensive microstructural characterization as well as preliminary digestion studies are performed on three bituminous coals (Herrin and Springfield from the Illinois Basin and the Blue Gem from the Central Appalachians) and one subbituminous coal from the Powder River Basin (Monarch), as raw material candidates. The subbituminous coal was richer in oxygen, lower in sulfur, and had a higher volatile matter yield. Microstructural investigations were performed using X-ray diffraction, X-ray/neutron computed tomography, scanning electron microscopy with energy dispersive spectroscopy, and petrology. Mild solvent extraction studies were conducted using creosote and decant oil as solvents in microreactors. The extraction yield was sensitive to temperature and time (350 to 450 °C between 30 and 120 mins.) for both creosote and decant oil digestions. While the Blue Gem coal had more desirable microstructural properties with less mineral content and cleaner macerals, it had the lowest coal conversion to quinoline soluble ‘liquid’ (of the bituminous coals). The lower coal conversion yield was hypothesized to be connected to the lack of FeS2 which could act as a catalyst when Fe is liberated from the structure under solvent extraction conditions. The Herrin and Springfield coals revealed similar microstructures and coal conversion efficiencies (higher than Blue Gem). These coals were the most promising candidates for further examination from this first approximations study. The subbituminous Monarch coal, however, was deemed less suitable due to poor coal conversion and less desirable microstructures. Additionally, the presented results with combined microstructural data from multiple length scales established a framework necessary for a first approximations study in this new coal utilization approach.

01 COAL, LIGNITE, AND PEAT↗

Microstructure-sensitive modeling of high temperature creep in grade-91 alloy

Predicting the effects of microstructure on high-temperature creep responses of steel components is critical to minimize the risks of failure and maximize economic viability in the energy sector. In this research, a recently developed advanced mechanistic constitutive model is employed to study the effect of microstructure on the creep responses and to rationalize experimentally reported variability in the performances of grade-91 alloy. Hundreds of experimental creep tests from the literature are used to assess the predictability of the model. The model proposed is shown to accurately predict the steady-state creep rates and also the less commonly considered, yet important, primary-to-secondary transients for a wide range of creep conditions. Further, the model is capable of extrapolating the creep response of grade 91 alloy even outside of the calibration regime. Using this model, the roles of initial microstructure described in terms of grain size, dislocation density, and precipitate content, on the creep responses are investigated. The effect of initial microstructure on the steady-state creep rates and creep-strain is found to vary with stress and temperature. Grain size plays a significant role in the low-stress creep, where the diffusional creep is dominant. On the other hand, the effects of dislocation densities and precipitate content are significant in the dislocation-plasticity-dominated high-stress and temperature regimes. Furthermore, by comparing model predictions against a large experimental creep database, it is found that variability in the creep responses can be rationalized on the basis of differences in the initial microstructure. Overall, this work provides a robust pathway for microstructure-aware engineering design, verification, and validation of metallic components for energy applications.

36 MATERIALS SCIENCE↗

Microstructural banding of directed energy deposition-additively manufactured 316L stainless steel

The microstructures of 316 L stainless steel created by rapid solidification are investigated here by comparing the similar microstructures of individual hatches of directed energy deposition additive manufacturing (DED-AM) and those of single, laser surface-melted tracks formed on a solid plate. High recoil pressure, which is exponentially dependent on the laser beam power density, induces convection of the melt pool, which causes formation of microstructural bands in the as-solidified microstructure. The microstructural bands are associated with changes in the chromium concentration and are a significant component of the inhomogeneous microstructure of DED-AM.

36 MATERIALS SCIENCE↗

Effects of Irradiation on the Microstructure of U-7Mo Dispersion Fuel with Al-2Si Matrix

The Reduced Enrichment for Research and Test Reactor program is developing low-enriched uranium U-Mo dispersion fuels for application in research and test reactors around the world. As part of this development, fuel plates have been irradiated in the Advanced Test Reactor and then characterized using optical metallography (OM) and scanning electron microscopy (SEM) to determine the as-irradiated microstructure. To demonstrate the irradiation performance of U-7Mo dispersion fuel plates with 2 wt% Si added to the matrix, fuel plates were tested to medium burnups at intermediate fission rates as part of the RERTR-6 experiment. Further testing was performed to higher fission rates as part of the RERTR-7A experiment, and very aggressive testing (high temperature, high fission density, high fission rate) was performed in the RERTR-9A, RERTR-9B and AFIP-1 experiments. As-irradiated microstructures were compared to those observed after fabrication to determine the effects of irradiation on the microstructure. Based on comparison of the microstructural characterization results for each irradiated sample, some general conclusions can be drawn about how the microstructure evolves during irradiation: there is growth of the fuel/matrix interaction layer (FMI), which was present in the samples to some degree after fabrication, during irradiation; Si diffuses from the FMI layer to deeper depths in the U-7Mo particles as the irradiation conditions are made more aggressive; lowering of the Si content in the FMI layer results in an increase in the size of the fission gas bubbles; as the FMI layer grows during irradiation more Si diffuses from the matrix to the FMI layer/matrix interface, and interlinking of fission gas bubbles in the fuel plate microstructure that may indicate breakaway swelling is not observed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗