Results for “Model Reference Control” — Page 21

NASA NTRS2011

Flight Test Maneuvers for Efficient Aerodynamic Modeling

Novel flight test maneuvers for efficient aerodynamic modeling were developed and demonstrated in flight. Orthogonal optimized multi-sine inputs were applied to aircraft control surfaces to excite aircraft dynamic response in all six degrees of freedom simultaneously while keeping the aircraft close to chosen reference flight conditions. Each maneuver was designed for a specific modeling task that cannot be adequately or efficiently accomplished using conventional flight test maneuvers. All of the new maneuvers were first described and explained, then demonstrated on a subscale jet transport aircraft in flight. Real-time and post-flight modeling results obtained using equation-error parameter estimation in the frequency domain were used to show the effectiveness and efficiency of the new maneuvers, as well as the quality of the aerodynamic models that can be identified from the resultant flight data.

Morelli, Eugene A.↗

NASA NTRS1973

A 'type one' servo explicit model following adaptive scheme.

This paper describes 'type 1' servo techniques applied to explicit model following systems. The advantages of using these are: (1) steady-state decoupling is provided for the controlled state variables as determined by a reference input (the pilot command for example), (2) overall stability of the decoupled adaptive scheme is guaranteed, (3) a zero steady-state error for those state variables incorporating integral feedback, to a constant input reference, and (4) improved transient performance. Example calculations have been performed using a mathematical model for a typical fighter aircraft and a desired performance reference model based on satisfactory aircraft flying qualities. Numerical results are given.

Tiroshi, I.↗

NASA NTRS1979

Configuration management and automatic control of an augmentor wing aircraft with vectored thrust

An advanced structure for automatic flight control logic for powered-lift aircraft operating in terminal areas is under investigation at Ames Research Center. This structure is based on acceleration control; acceleration commands are constructed as the sum of acceleration on the reference trajectory and a corrective feedback acceleration to regulate path tracking errors. The central element of the structure, termed a Trimmap, uses a model of the aircraft aerodynamic and engine forces to calculate the control settings required to generate the acceleration commands. This report describes the design criteria for the Trimmap and derives a Trimmap for Ames experimental augmentor wing jet STOL research aircraft.

Cicolani, L. S.↗

NASA NTRS1999

The Identification and Modeling of Visual Cue Usage in Manual Control Task Experiments

Many fields of endeavor require humans to conduct manual control tasks while viewing a perspective scene. Manual control refers to tasks in which continuous, or nearly continuous, control adjustments are required. Examples include flying an aircraft, driving a car, and riding a bicycle. Perspective scenes can arise through natural viewing of the world, simulation of a scene (as in flight simulators), or through imaging devices (such as the cameras on an unmanned aerospace vehicle). Designers frequently have some degree of control over the content and characteristics of a perspective scene; airport designers can choose runway markings, vehicle designers can influence the size and shape of windows, as well as the location of the pilot, and simulator database designers can choose scene complexity and content. Little theoretical framework exists to help designers determine the answers to questions related to perspective scene content. An empirical approach is most commonly used to determine optimum perspective scene configurations. The goal of the research effort described in this dissertation has been to provide a tool for modeling the characteristics of human operators conducting manual control tasks with perspective-scene viewing. This is done for the purpose of providing an algorithmic, as opposed to empirical, method for analyzing the effects of changing perspective scene content for closed-loop manual control tasks.

Sweet, Barbara Townsend↗

NASA NTRS2009

Adaptive Control of a Transport Aircraft Using Differential Thrust

The paper presents an adaptive control technique for a damaged large transport aircraft subject to unknown atmospheric disturbances such as wind gust or turbulence. It is assumed that the damage results in vertical tail loss with no rudder authority, which is replaced with a differential thrust input. The proposed technique uses the adaptive prediction based control design in conjunction with the time scale separation principle, based on the singular perturbation theory. The application of later is necessitated by the fact that the engine response to a throttle command is substantially slow that the angular rate dynamics of the aircraft. It is shown that this control technique guarantees the stability of the closed-loop system and the tracking of a given reference model. The simulation example shows the benefits of the approach.

Stepanyan, Vahram↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. 4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability. (5) The directional control effectiveness 'of the TCA rudder is the same as that of the Reference H rudder at low angles-of-attack, after taking factors, such as number of rudder panels deflected and vertical tail volume into account. However, rudder effectiveness was shown to be reduced at higher angles-of-attack. (6) The lateral stability was shown to be reduced relative to the Reference H, which may be beneficial at low speeds for alleviating lateral control saturation. (7) Lateral control effectiveness for the TCA was shown to be similar to the Reference H for negative trailing-edge flap deflections and was reduced by approximately 25% for positive trailing-edge flap deflections.

Kubiatko, Paul↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. (4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability.

Kubiatko, Paul↗

NASA NTRS1993

System identification of the Large-Angle Magnetic Suspension Test Facility (LAMSTF)

The Large-Angle Magnetic Suspension Test Facility (LAMSTF), a laboratory-scale research project to demonstrate the magnetic suspension of objects over wide ranges of attitudes, has been developed. This system represents a scaled model of a planned Large-Gap Magnetic Suspension System (LGMSS). The LAMSTF system consists of a planar array of five copper electromagnets which actively suspend a small cylindrical permanent magnet. The cylinder is a rigid body and can be controlled to move in five independent degrees of freedom. Five position variables are sensed indirectly by using infra-red light-emitting diodes and light-receiving phototransistors. The motion of the suspended cylinder is in general nonlinear and hence only the linear, time-invariant perturbed motion about an equilibrium state is considered. One of the main challenges in this project is the control of the suspended element over a wide range of orientations. An accurate dynamic model plans an essential role in controller design. The analytical model of the LAMSTF system includes highly unstable real poles (about 10 Hz) and low-frequency flexible modes (about 0.16 Hz). Projection filters are proposed to identify the state space model from closed-loop test data in time domain. A canonical transformation matrix is also derived to transform the identified state space model into the physical coordinate. The LAMSTF system is stabilized by using a linear quadratic regulator (LQR) feedback controller. The rate information is obtained by calculating the back difference of the sensed position signals. The reference inputs contain five uncorrelated random signals. This control input and the system reponse are recorded as input/output data to identify the system directly from the projection filters. The sampling time is 4 ms and the model is fairly accurate in predicting the step responses for different controllers while the analytical model has a deficiency in the pitch axis.

Huang, Jen-Kuang↗

NASA NTRS1986

Analytical investigation of the dynamics of tethered constellations in Earth orbit, phase 2

The development of a two dimensional analytical model that describes the dynamics of an n-mass vertical tethered system is reported. Two different approaches are described: in the first one the control quantities are the independent variables while in the second one the Cartesian coordinates of each mass expressed in the orbiting reference frame are the independent variables. The latter model was used in the 3-mass version to simulate the dynamics of the tethered system in applications involving the displacement of the middle mass along the tether. In particular, issues related to reproducing predetermined acceleration profiles and g-tuning are reported.

Lorenzini, E.↗

DOE OSTI2024

Equivalent-Circuit Models for Grid-Forming Inverters under Unbalanced Steady-State Operating Conditions: Preprint

Positive- and negative-sequence equivalent-circuit models are put forth to capture the operation of grid-forming (GFM) inverters in unbalanced steady-state operating conditions acknowledging the impact of current limiting. The particular control architecture examined adopts droop control (for primary control), nested inner-current and outer-voltage control (in the stationary reference frame), and it is adaptable to two different types of current limiting (current-reference saturation and virtual-impedance limiting). We anticipate the proposed models to be of interest in modeling, analysis, and simulation of GFM inverters in unbalanced settings that may arise, e.g., in the face of faults. Validation of the equivalent-circuit models is pursued via comparison with full-order electromagnetic-transient (EMT) simulations for representative balanced and unbalanced faults.

equivalent-circuit models↗

NASA NTRS2023

Thermomechanical Real-Time Hybrid Simulation: Conceptual Framework and Control Requirements

Real-time hybrid simulation (RTHS) is an enabling technology that has transformed engineering experimentation and helped researchers expand modeling capabilities. However, breakthroughs are necessary to expand the range of hybrid simulation methods and, thus, enable experiments with loading conditions representing multiple hazards. This paper discusses the development of a new thermomechanical RTHS framework and a systematic approach to determining RTHS control requirements. First, the framework is established using a representative finite element model of a layered structural system subjected to thermal loading. A complete two-layer system model serves as the reference system, and it is then partitioned into a numerical layer and an experimental layer that share interface conditions. Next, a thermal actuator is introduced to impose dynamic thermal loading on the experimental subsystem, serving as a transfer system. Finally, control and performance metrics are defined to evaluate the realization of interface boundary conditions and map this to the RTHS execution. Through an illustrative example considering the influence of temperature on a lunar habitat, we demonstrate how to establish controller requirements for RTHS and demonstrate that this approach can be used to conduct RTHS on structures with thermomechanical loading.

Herta Montoya↗

DOE OSTI2026

A bi-level advanced control framework for large-scale control of buildings with system-level impact

Increased electricity consumption combined with new forms of generation is testing the reliability of our grid infrastructure. This work describes a method to improve the reliability of the grid through large-scale advanced building control. This paper develops a bi-level distributed control framework to shift the load of 153 buildings to achieve a system-level objective of tracking a power reference signal. This bi-level control is based on the previously-developed ANPV-MPC, a predictive controller that uses a Bayesian neural network to generate an accurate control model and adapt to changing conditions over time. By shifting the building electricity demand to better match the available power, the grid system supplying the buildings is more reliable as evidenced by the analysis of node voltages across an IEEE 13-bus distribution system. The proposed bi-level control framework tracks the system-level power reference with enough accuracy to regulate node voltages across the IEEE 13-bus distribution system within ANSI limits of ±5%. Additionally, the adaptive nature of ANPV-MPC allows each building across the system to adapt to changing conditions, further amplifying the system-level reliability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS2018

ST7 Disturbance Reduction System (DRS) Colloid Micronewton Thruster Performance and Control Algorithm Model Simulation Validation in Flight

Colloid Micronewton Thrusters (CMNT) were flight demonstrated for the first time on the ST7Disturbance Reduction System (DRS) payload on the European Space Agency (ESA) Laser Interferometer Space Antenna (LISA) Pathfinder spacecraft for attitude and drag-free spacecraft control. LISA Pathfinder was a technology demonstration mission for ESA’s LISA gravitational wave observatory, currently in Phase A with a launch date of 2034. The DRS included the Integrated Avionics Unit (IAU), eight Colloid Micronewton Thrusters (CMNT), Dynamic Control Software (DCS) and Flight Software (FSW). The CMNT technology met performance requirements operating at 5-30 µN of thrust with ≤0.1 µN resolution and ≤0.1 µN/Hz thrust noise to deliver the required nanometer-level precision spacecraft control measured by the gravitational reference sensor (GRS) in the ESA LISA Technology Package (LTP). The performance of seven of the CMNT in flight was consistent with ground test results. The colloid thruster performance model of thrust and thrust noise as a function of operational parameters (i.e. beam current, voltage, temperature, etc.) was validated in flight over a wide range of conditions. A model and simulation of the thruster control algorithm was developed and validated with flight data to predict thrust noise. This capability is important because it is considered to be a significant source of position noise on the spacecraft and, therefore, the acceleration noise on the test masses, which provide the gravity wave measurements. The CMNT thruster model data and validation with LISA Pathfinder/ST7-DRS flight experiments are discussed in this paper.

Hruby, Vlad↗

NASA NTRS1988

A brief review on the identification of nonlinear mechanical systems

This paper presents a brief review of the disciplines used in the identification of nonlinear mechanical systems, including the detection of nonlinearities and their quantification, and parameter estimation. Techniques for determining the parameters of nonlinear system models with assumed model form are described and briefly discussed. Recent developments in identifying system models which may contain the actual model forms as well as incorrect forms is also briefly described. A list of representative references from structures and control disciplines is given.

Natke, H. G.↗

NASA NTRS1988

The inclusion of semi-Markov reconfiguration transitions into the computer-aided Markov evaluator (CAME) program

The modifications to the rule-based CAME program which allow it to more accurately model the fault-handling processes of fault-tolerant systems are described. This new capability is added to the CAME program by modeling the fault-handling processes of fault-tolerant systems. The integrated airframe/propulsion control system architecture (IAPSA II) reference configuration currently under development is detailed.

Rosch, Gene↗

NASA NTRSDate not supplied

Utilizing Advanced Air Mobility Rotorcraft Tools for Wildfire Applications

Over the past decade, due in large part to heavy investment in the field of Advanced Air Mobility (AAM), significant progress in rotorcraft-focused modeling tools has been made. Such progress has notably increased AAM rotorcraft modeling capabilities in the topics of conceptual design, preliminary design, and more recently flight dynamics. Yet, due to recent and persistent increases in extreme weather events, an emerging interest has been raised in utilizing such modeling capabilities for aiding in emergency relief efforts and other public good missions. This paper uses wildfire fighting as a representative public good mission and demonstrates the relevance of the NASA Revolutionary Vertical Lift Technology (RVLT) rotorcraft toolchain to such missions. An emphasis is placed on flight dynamics modeling and control because of the hazards and challenges associated with the atmospheric environment of wildfires. In this work, the NASA FlightCODE tool was used to analyze both a UH-60 and the NASA six-passenger quadcopter reference model hovering in an experimentally informed wildfire turbulent environment. Preliminary results of this study estimate actuator usage exceedances and disturbance rejection capabilities of the vehicles’ translational rate command systems. Leveraging the RVLT toolchain, refinement and expansion of this work could lead to handling qualities envelope estimation and design optimization for wildfire turbulent environments. This would provide pilots with additional information to make real-time decisions in high-risk scenarios and begins preparations for simulating these dangerous environments for pilot training and experimentation.

Rotorcraft↗

NASA NTRSDate not supplied

Utilizing Advanced Air Mobility Rotorcraft Tools for Wildfire Applications

Over the past decade, due in large part to heavy investment in the field of Advanced Air Mobility (AAM), significant progress in rotorcraft-focused modeling tools has been made. Such progress has notably increased AAM rotorcraft modeling capabilities in the topics of conceptual design, preliminary design, and more recently flight dynamics. Yet, due to recent and persistent increases in extreme weather events, an emerging interest has been raised in utilizing such modeling capabilities for aiding in emergency relief efforts and other public good missions. This paper uses wildfire fighting as a representative public good mission and demonstrates the relevance of the NASA Revolutionary Vertical Lift Technology (RVLT) rotorcraft toolchain to such missions. An emphasis is placed on flight dynamics modeling and control because of the hazards and challenges associated with the atmospheric environment of wildfires. In this work, the NASA FlightCODE tool was used to analyze both a UH-60 and the NASA six-passenger quadcopter reference model hovering in an experimentally informed wildfire turbulent environment. Preliminary results of this study estimate actuator usage exceedances and disturbance rejection capabilities of the vehicles’ translational rate command systems. Leveraging the RVLT toolchain, refinement and expansion of this work could lead to handling qualities envelope estimation and design optimization for wildfire turbulent environments. This would provide pilots with additional information to make real-time decisions in high-risk scenarios and begins preparations for simulating these dangerous environments for pilot training and experimentation.

Rotorcraft↗

NASA NTRS1976

FLEXSTAB: A computer program for the prediction of loads and stability and control of flexible aircraft

Capabilities of the FLEXSTAB Computer Program System are described and illustrated. Aeroelastic analysis of a wide variety of aircraft configurations is performed. The aerodynamic theory used in FLEXSTAB is applicable to both steady and unsteady, subsonic and supersonic flow for multiple wing-body tail nacelle configurations with a plane of symmetry. For unsteady flow calculations, an unsteady aerodynamic theory is used which is appropriate for the low reduced frequencies associated with aircraft flight dynamics. The aircraft is modeled as either a rigid or flexible structure. The computer trims the aircraft in steady reference flight and computes both static and dynamic stability and control derivatives and the stability behavior about the trim condition. The airplane lifting pressure distribution, aerodynamic and inertia loads and deflected shape are also computed.

Perkin, B. R.↗