Search NASA⌕ Search

SEARCH · Search NASA

Results for “Novel Characterization Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

A rapid noninvasive characterization of CT x-ray sources

Purpose: The aim of this study is to generate spatially varying half value layers (HVLs) that can be used to construct virtual equivalent source models of computed tomography (CT) x-ray sources for use in Monte Carlo CT dose computations. Methods: To measure the spatially varying HVLs, the authors combined a cylindrical HVL measurement technique with the characterization of bowtie filter relative attenuation (COBRA) geometry. An apparatus given the name “HVL Jig” was fabricated to accurately position a real-time dosimeter off-isocenter while surrounded by concentric cylindrical aluminum filters (CAFs). In this geometry, each projection of the rotating x-ray tube is filtered by an identical amount of high-purity (type 1100 H-14) aluminum while the stationary radiation dose probe records an air kerma rate versus time waveform. The CAFs were progressively nested to acquire exposure data at increasing filtrations to calculate the HVL. Using this dose waveform and known setup geometry, each timestamp was related to its corresponding fan angle. Data were acquired using axial CT protocols (i.e., rotating tube and stationary patient table) at energies of 80, 100, and 120 kVp on a single CT scanner. These measurements were validated against the more laborious conventional step-and-shoot approach (stationary x-ray tube). Results: At each energy, HVL data points from the COBRA-cylinder technique were fit to a trendline and compared with the conventional approach. The average relative difference in HVL between the two techniques was 1.3%. There was a systematic overestimation in HVL due to scatter contamination. Conclusions: The described method is a novel, rapid, accurate, and noninvasive approach that allows one to acquire the spatially varying fluence and HVL data using a single experimental setup in a minimum of three scans. These measurements can be used to characterize the CT beam in terms of the angle-dependent fluence and energy spectra along the bowtie filter direction, which can serve as input for accurate CT dose computations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Impaired response of mature adipocytes of diabetic mice to hypoxia

Adipose tissue contains various cells such as infiltrated monocytes/macrophages, endothelial cells, preadipocytes, and adipocytes. Adipocytes have an endocrine function by secreting adipokines such as interleukin (IL)-6, tumor necrosis factor (TNF)-{alpha}, leptin, and adiponectin. Dysregulation of adipokines in adipose tissues leads to a chronic low-grade inflammation which could result in atherosclerosis, hypertension, and type 2 diabetes. A sustained inflammatory state, which is characterized by prolonged persistence of macrophages and neutrophils, is found in diabetic wounds. In addition, subcutaneous adipocytes are enormously increased in amount clinically in type 2 diabetes. However, the function of subcutaneous adipocytes, which play an important role in injured tissue subjected to hypoxia, has not been well characterized in vitro due to the difficulty of maintaining mature adipocytes in culture using conventional methods because of their buoyancy. In this study, we established a novel in vitro culture method of mature adipocytes by enclosing them in a hyaluronan (HA) based hydrogel to study their role in response to stress such as hypoxia. BrdU labeling and Ki67 immunostaining experiments showed that hydrogel enclosed mature adipocytes proliferate in vitro. Both mRNA and protein expression analyses for hypoxia regulated genes, such as vascular endothelial growth factor (VEGF) and heme oxygenase 1 (HO1), showed that mature adipocytes of wild type mice respond to hypoxia. In contrast, mature adipocytes of diabetic db/db and TallyHo mice did not efficiently respond to hypoxia. Our studies suggest that mature adipocytes are functionally active cells, and their abnormal function to hypoxia can be one of underlining mechanisms in type 2 diabetes.

60 APPLIED LIFE SCIENCES↗

Synthesis, Characterization, and Catalytic Properties of Novel Single-Site and Nanosized Platinum Catalysts

Novel single-site platinum catalysts have been synthesized by reacting platinum(II) organometallics with partially dehydroxylated silica. The resulting materials have been characterized by various methods such as IR, MAS NMR, and EXAFS. Further, the single-site platinum catalysts were calcined in air to remove the ligand and produce nanosized platinum particles, that were characterized by TEM and H{sub 2} chemisorption. All catalysts were tested for the hydrogenation of toluene. The single-site platinum catalysts were less active than a commercial Pt/SiO{sub 2} catalyst with comparable platinum loading, and this has been ascribed to ligand effects. Conversely, the nanosized platinum catalysts were more active than the commercial Pt/SiO{sub 2} catalyst due to their high dispersion and small particle sizes.

36 MATERIALS SCIENCE↗

Parameter degeneracy in flavor-dependent reconstruction of supernova neutrino fluxes

We re-examine the possibility of reconstructing the initial fluxes of supernova neutrinos emitted in a future core-collapse galactic supernova explosion and detected in a megaton-sized water Cherenkov detector. A novel key element in our method is the inclusion, in addition to the total and the average energies of each neutrino species, of a 'pinching' parameter characterizing the width of the distribution as a fit parameter. We uncover in this case a continuous degeneracy in the reconstructed parameters of supernova neutrino fluxes at the neutrinosphere. We analyze in detail the features of this degeneracy and show how it occurs irrespective of the parameterization used for the distribution function. Given that this degeneracy is real we briefly comment on possible steps towards resolving it, which necessarily requires going beyond the setting presented here.

79 ASTRONOMY AND ASTROPHYSICS↗

Machine Learning Reveals Missing Edges and Putative Interaction Mechanisms in Microbial Ecosystem Networks

Different organisms in a microbial community may drastically affect each other’s growth phenotypes, significantly affecting the community dynamics, with important implications for human and environmental health. Novel culturing methods and the decreasing costs of sequencing will gradually enable high-throughput measurements of pairwise interactions in systematic coculturing studies. However, a thorough characterization of all interactions that occur within a microbial community is greatly limited both by the combinatorial complexity of possible assortments and by the limited biological insight that interaction measurements typically provide without laborious specific follow-ups. Here, we show how a simple and flexible formal representation of microbial pairs can be used for the classification of interactions via machine learning. The approach we propose predicts with high accuracy the outcome of yet-to-be performed experiments and generates testable hypotheses about the mechanisms of specific interactions.

59 BASIC BIOLOGICAL SCIENCES↗

Profiling microbial lignocellulose degradation and utilization by emergent omics technologies

The use of plant materials to generate renewable biofuels and other high-value chemicals is the sustainable and preferable option, but will require considerable improvements to increase the rate and efficiency of lignocellulose depolymerization. This review highlights novel and emergent technologies that are being developed and deployed to characterize the process of lignocellulose degradation. The review will also illustrate how microbial communities deconstruct and metabolize lignocellulose by identifying the necessary genes and enzyme activities along with the reaction products. These technologies include multi-omic measurements, cell sorting and isolation, nuclear magnetic resonance spectroscopy (NMR), activity-based protein profiling, and direct measurement of enzyme activity. The recalcitrant nature of lignocellulose necessitates the need to characterize the methods microbes employ to deconstruct lignocellulose to inform new strategies on how to greatly improve biofuel conversion processes. New technologies are yielding important insights into microbial functions and strategies employed to degrade lignocellulose, providing a mechanistic blueprint to advance biofuel production.

Rosnow, Joshua J.↗

Facile synthesis, optical and photoconductive properties of novel ZnO nanocones

Large-scale, uniform ZnO nanocones with tips about 200 nm and length about 50 {mu}m have been synthesized by a facile hydrothermal method. The morphology and structures were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and high-resolution transmission electron microscope (HR-TEM). The effects of reaction time and PEG-400 on the morphology of ZnO nanostructures were investigated, also an oriented attachment mechanism has been briefly proposed. The optical properties were investigated by lasing confocal microscope and photoluminescence spectrum, a strong near band edge emission peak centered at 387 nm from the ZnO nanocones was observed in photoluminescence spectrum. Finally, we have fabricated UV photodetector based on single ZnO nanocone, which present good switching properties by turning the UV light on and off.

36 MATERIALS SCIENCE↗

Novel Experiments to Characterize Creep-Fatigue Degradation in VHTR Alloys

It is well known in energy systems that the creep lifetime of high temperature alloys is significantly degraded when a cyclic load is superimposed on components operating in the creep regime. A test method has been developed in an attempt to characterize creep-fatigue behavior of alloys at high temperature. The test imposes a hold time during the tensile phase of a fully reversed strain-controlled low cycle fatigue test. Stress relaxation occurs during the strain-controlled hold period. This type of fatigue stress relaxation test tends to emphasize the fatigue portion of the total damage and does not necessarily represent the behavior of a component in-service well. Several different approaches to laboratory testing of creep-fatigue at 950°C have been investigated for Alloy 617, the primary candidate for application in VHTR heat exchangers. The potential for mode switching in a cyclic test from strain control to load control, to allow specimen extension by creep, has been investigated to further emphasize the creep damage. In addition, tests with a lower strain rate during loading have been conducted to examine the influence of creep damage occurring during loading. Very short constant strain hold time tests have also been conducted to examine the influence of the rapid stress relaxation that occurs at the beginning of strain holds.

36 MATERIALS SCIENCE↗

Non -degenerate marginal-likelihood calibration with application to quantum characterization

Here, we propose a marginal likelihood strategy within the Kennedy-O’Hagan (KOH) Bayesian framework, where a Gaussian process (GP) models the discrepancy between a physical system and its simulator. Our approach introduces a novel marginalized likelihood by integrating out the degenerate eigenspace of the covariance matrix, rather than approximating the original likelihood. Unlike approximation methods that compromise accuracy for computational efficiency, our method defines an exact likelihood—distinct from the original but preserving all relevant information. This formulation achieves computational efficiency and stability, even for large datasets where the covariance matrix nears degeneracy. Applied to the characterization of a superconducting quantum device at Lawrence Livermore National Laboratory, the approach enhances the predictive accuracy of the Lindblad master equations for modeling Ramsey measurement data by effectively quantifying uncertainties consistent with the quantum data.

general physics↗

Developing extreme fast charge battery protocols – A review spanning materials to systems

Extreme fast charging (XFC) has become a focal research point in the lithium-battery community over the last several years. As adoption of electric vehicles increases, fast charging has become a key driver in enhancing consumer recharge experience. Recently, the research community has made significant improvements in developing charge protocols to support XFC. New charge protocol designs derived using a combination of advanced, physically derived models, and electrochemical and secondary characterization methods, increase charge acceptance and decrease aging. By coordinating these methods and modifying protocols to account for different material constraints, including lithium plating and cathode particle degradation, novel charge protocols have increased the energy accepted during charging by over 25% in 10 min and increased the charge acceptance prior to a constant-voltage step by approximately 3x. Here, we review several charge-protocol advances, aging factors which are enhanced by XFC and advances which will enable adoption of XFC capable vehicles. These advances include implementing machine learning and other detection algorithms to reduce and classify lithium plating, which is known to significantly degrade cell performance and reduce cell life. The review concludes by discussing full-system fast charge requirements, including electric vehicle service equipment needs for implementing XFC protocols.

25 ENERGY STORAGE↗

Functionalization of multi-walled carbon nanotubes using water-assisted chemical vapor deposition

A simple and novel method, water-assisted chemical vapor deposition (CVD) was developed to functionalize multi-walled carbon nanotubes (MWCNTs) during the synthesis process. The functionalized MWCNTs were characterized using Raman spectroscopy, XPS, TGA, NH{sub 3}-TPD, SEM and HR-TEM. It was found that new defects are introduced and the amount of acidic groups is increased on the MWCNT surface during the water-assisted CVD process. The amount of C-OH and C-O group on the MWCNT surface is found to be increased from 21.1% to 42% with water vapor assistance. Density functional theory (DFT) was employed to study the chemical behavior of water vapor molecule on the catalyst particle surface of Ni(1 1 1) cluster. Based on the experimental and DFT simulation results, a mechanism for functionalization of MWCNTs by water-assisted CVD is proposed. - Graphical abstract: Water is adsorbed and activated on Ni surface, then dissociated into OH and O species, followed by part of OH and O species desorbed from the surface. Finally, the desorbed OH and O species oxidize the unsaturated carbon atoms of carbon nanotubes, form defects and oxygen-containing groups. Highlights: Black-Right-Pointing-Pointer MWCNTs were functionalized by water-assisted CVD method. Black-Right-Pointing-Pointer Defects and weak-medium acidic sites were created on the MWCNT sidewalls. Black-Right-Pointing-Pointer Oxygen-containing groups in functionalized MWCNT were increased from 21.1% to 42%. Black-Right-Pointing-Pointer A mechanism for the influence of water vapor on MWCNTs was proposed.

36 MATERIALS SCIENCE↗

Temperature dependence of magnetic property and photocatalytic activity of Fe{sub 3}O{sub 4}/hydroxyapatite nanoparticles

Fe{sub 3}O{sub 4}/hydroxyapatite (HAP) nanoparticles have been developed as a novel photocatalyst support, based on the embedment of magnetic Fe{sub 3}O{sub 4} particles into HAP shell via homogeneous precipitation method. The resultant nanoparticles were characterized by transmission electron microscope (TEM) and X-ray diffraction (XRD). These particles were almost spherical in shape, rather monodisperse and have a unique size of about 25 nm in diameter. The effect of calcination temperature on magnetic property and photocatalytic activity of Fe{sub 3}O{sub 4}/HAP nanoparticles was investigated in detail. The obtained results showed that the Fe{sub 3}O{sub 4}/HAP nanoparticles calcined at 400 {sup o}C possessed good magnetism and photocatalytic activity in comparison with that calcined at other temperatures.

36 MATERIALS SCIENCE↗

A novel Bi-based oxybromide SrBiO{sub 2}Br: Synthesis, optical property and photocatalytic activity

Highlights: • SrBiO{sub 2}Br was first explored as a novel photocatalyst. • SrBiO{sub 2}Br has been successfully synthesized by a solid state reaction. • We systematically synthesized SrBiO{sub 2}Br in different temperature. • SrBiO{sub 2}Br calcinated at 700 °C exhibited the highest photocatalytic activity. - Abstract: A novel Bi-based photocatalyst SrBiO{sub 2}Br with layered structure was successfully synthesized via a solid state reaction method. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–vis diffuse reflectance spectra (DRS). SrBiO{sub 2}Br has an indirect-transition optical band-gap of 2.58 eV. Density functional calculations revealed that conduction band (CB) were composed of the Bi 6p and Br 4s orbitals, and valence band (VB) were occupied by Br 4p and O 2p. The photodecomposition of rhodamine-B (RhB) experiments demonstrated SrBiO{sub 2}Br can be used as photocatalysts under ultraviolet (UV) light and visible light irradiation (λ > 400 nm). The results revealed that SrBiO{sub 2}Br calcinated at 700 °C exhibited the highest photocatalytic activity among the obtained SrBiO{sub 2}Br samples.

36 MATERIALS SCIENCE↗

PCAfold 2.0—Novel tools and algorithms for low-dimensional manifold assessment and optimization

We describe an update to our open-source Python package, PCAfold, designed to help researchers generate, analyze and improve low-dimensional data manifolds. In the current version, PCAfold 2.0, we introduce novel tools and algorithms for assessing and optimizing low-dimensional manifolds. This includes a method that generates a “map” of local feature sizes that can help pinpoint researchers to problematic regions on a manifold. We introduce a novel cost function that characterizes the quality of a manifold topology with a single number. We develop two algorithms for feature selection based on principal component analysis (PCA) that use the cost function as an objective function to minimize. We introduce a quantity of interest (QoI)-aware dimensionality reduction strategy where data projections are computed using an artificial neural network and are directly optimized towards representing various projection-independent and projection-dependent QoIs. We also introduce an implementation of partition of unity networks (POUnets) for efficient reconstruction of QoIs from low-dimensional manifolds based on combining neural network classification with localized polynomial regression. Our software can be broadly applicable in all domains of science and engineering that aim to reduce data dimensionality, as well as in the fundamental research on representation learning.

97 MATHEMATICS AND COMPUTING↗

TH-CD-207A-03: A Surface Deformation Driven Respiratory Model for Organ Motion Tracking in Lung Cancer Radiotherapy

Purpose: To propose and validate a novel real-time surface-mesh-based internal organ-external surface motion and deformation tracking method for lung cancer radiotherapy. Methods: Deformation vector fields (DVFs) which characterizes the internal and external motion are obtained by registering the internal organ and tumor contours and external surface meshes to a reference phase in the 4D CT images using a recent developed local topology preserved non-rigid point matching algorithm (TOP). A composite matrix is constructed by combing the estimated internal and external DVFs. Principle component analysis (PCA) is then applied on the composite matrix to extract principal motion characteristics and finally yield the respiratory motion model parameters which correlates the internal and external motion and deformation. The accuracy of the respiratory motion model is evaluated using a 4D NURBS-based cardiac-torso (NCAT) synthetic phantom and three lung cancer cases. The center of mass (COM) difference is used to measure the tumor motion tracking accuracy, and the Dice’s coefficient (DC), percent error (PE) and Housdourf’s distance (HD) are used to measure the agreement between the predicted and ground truth tumor shape. Results: The mean COM is 0.84±0.49mm and 0.50±0.47mm for the phantom and patient data respectively. The mean DC, PE and HD are 0.93±0.01, 0.13±0.03 and 1.24±0.34 voxels for the phantom, and 0.91±0.04, 0.17±0.07 and 3.93±2.12 voxels for the three lung cancer patients, respectively. Conclusions: We have proposed and validate a real-time surface-mesh-based organ motion and deformation tracking method with an internal-external motion modeling. The preliminary results conducted on a synthetic 4D NCAT phantom and 4D CT images from three lung cancer cases show that the proposed method is reliable and accurate in tracking both the tumor motion trajectory and deformation, which can serve as a potential tool for real-time organ motion and deformation monitoring in lung cancer radiotherapy. This work is supported in part by grant from VARIAN MEDICAL SYSTEMS INC, the National Natural Science Foundation of China (no 81428019 and no 81301940), the Guangdong Natural Science Foundation (2015A030313302)and the 2015 Pearl River S&T Nova Program of Guangzhou (201506010096).

60 APPLIED LIFE SCIENCES↗

Evolution of Copper Electrodes Fabricated by Electroless Plating on BaZr0.7Ce0.2Y0.1O3-δ Proton-Conducting Ceramic Membrane: From Deposition to Testing in Methane

We investigated copper electrodes deposited onto a BaZr0.7Ce0.2Y0.1O3-δ (BZCY72) proton-conducting membrane via a novel electroless plating method, which resulted in significantly improved performance when compared to a traditional painted copper electrode. The increased performance was examined with a multiscale multitechnique characterization method including time-of-flight secondary-ion mass spectroscopy (TOF-SIMS), transmission electron microscopy (TEM), scanning spreading-resistance microscopy (SSRM), and atom-probe tomography (APT). Through this method, we observed that a palladium catalyst layer alloys with the copper electrode. We also explored the nature of a non-coking-induced carbon-rich phase that may be involved with the improved performance of the electrode.

36 MATERIALS SCIENCE↗

Characterization of Preliminary Powder Production and Consolidation for Advanced LEU Fuel Concepts

A set of novel uranium-based alloys has been proposed for use in advanced LEU fuel systems that utilize powder metallurgical methods for fabrication of the fuel forms. This study seeks to evaluate the effectiveness of current fabrication methods to produce powder of each of the candidate alloys and consolidate composite systems. Powder samples were produced via atomization and analyzed for particle size, shape, and microstructure utilizing sieving methods and scanning electron microscopy (SEM). Preliminary pellet consolidation tests were conducted with the atomized powder using a press and sinter method. The resulting pellets were analyzed via SEM to evaluate the morphology of the composite system. These preliminary tests demonstrate the ability to produce powder but did not yield the desired quality of powder and impacted the ability to fabricate a fully dense pellet. A refined process is under development to produce a higher yield of small (<250 µm) spherical powder.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel Synthesis and Characterization of Uranium-Zirconium Carbonitride by Direct Casting

UZrCN has exhibited thermophysical properties beneficial to high temperature reactor applications such as nuclear thermal rockets. The present work investigates a novel liquid phase synthesis method involving the admission of nitrogen gas during arc melting of uranium, zirconium, and carbon. Initial microstructural examinations using SEM indicated that the samples remain heterogenous with zirconium-rich cores in a uranium-rich matrix. Heterogeneity resulted from large differences in melting temperature of the major constituents and rapid solidification. Additional EDS, combustion analysis, and inert gas fusion analysis proved that the core regions have both uranium and zirconium and establish that carbon and nitrogen are retained during the fabrication process. XRD clarifies that the light elements did not form compounds with the uranium matrix but rather incorporated into the core region forming a sub-stoichiometric UZrCN. Heat treatment performed on equimolar U-Zr-C resulted in an increase in the homogenous phase present with an XRD pattern reflecting a ternary UZrCN despite small amounts of segregation in the final button.

36 - MATERIALS SCIENCE↗