Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optimal Experiment Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Failure Investigation & Design Optimization of a Photo-Multiplier Tube Assembly Under Thermal Loading

Analysis of GLAST ACD Photo-Multiplier Tube (PMT) assembly under thermal loading demonstrates that the glass tube experiences high stresses due to Coefficient of Thermal Expansion mismatch, as well as increased stress due to high stiffness and incompressibility of potting compound. Further investigation shows adverse loading effects due to the magnetic shield, a thin piece of steel wrapped around the PMT. This steel, Mu Metal, contained an overlap region that directly attributed to crack propagation in the outside surface of the tube. Sensitivities to different configurations were studied to reduce the stress and provide a more uniform loading throughout the PMT to ensure mission success. Studies indicate substituting a softer and more compressible potting compound and moving the Mu metal from the glass tube to the outside wall of the aluminum housing yields lower stress.

Dahya, Kevin↗
NASA NTRS1978

Stirling engine design manual

This manual is intended to serve both as an introduction to Stirling engine analysis methods and as a key to the open literature on Stirling engines. Over 800 references are listed and these are cross referenced by date of publication, author and subject. Engine analysis is treated starting from elementary principles and working through cycles analysis. Analysis methodologies are classified as first, second or third order depending upon degree of complexity and probable application; first order for preliminary engine studies, second order for performance prediction and engine optimization, and third order for detailed hardware evaluation and engine research. A few comparisons between theory and experiment are made. A second order design procedure is documented step by step with calculation sheets and a worked out example to follow. Current high power engines are briefly described and a directory of companies and individuals who are active in Stirling engine development is included. Much remains to be done. Some of the more complicated and potentially very useful design procedures are now only referred to. Future support will enable a more thorough job of comparing all available design procedures against experimental data which should soon be available.

Martini, W. R.↗
NASA NTRS1991

Acquisition and production of skilled behavior in dynamic decision-making tasks: Modeling strategic behavior in human-automation interaction: Why and aid can (and should) go unused

Advances in computer and control technology offer the opportunity for task-offload aiding in human-machine systems. A task-offload aid (e.g., an autopilot, an intelligent assistant) can be selectively engaged by the human operator to dynamically delegate tasks to an automated system. Successful design and performance prediction in such systems requires knowledge of the factors influencing the strategy the operator develops and uses for managing interaction with the task-offload aid. A model is presented that shows how such strategies can be predicted as a function of three task context properties (frequency and duration of secondary tasks and costs of delaying secondary tasks) and three aid design properties (aid engagement and disengagement times, aid performance relative to human performance). Sensitivity analysis indicates how each of these contextual and design factors affect the optimal aid aid usage strategy and attainable system performance. The model is applied to understanding human-automation interaction in laboratory experiments on human supervisory control behavior. The laboratory task allowed subjects freedom to determine strategies for using an autopilot in a dynamic, multi-task environment. Modeling results suggested that many subjects may indeed have been acting appropriately by not using the autopilot in the way its designers intended. Although autopilot function was technically sound, this aid was not designed with due regard to the overall task context in which it was placed. These results demonstrate the need for additional research on how people may strategically manage their own resources, as well as those provided by automation, in an effort to keep workload and performance at acceptable levels.

Kirlik, Alex↗
NASA NTRS1993

Data management for interdisciplinary field experiments: OTTER project support

The ability of investigators of an interdisciplinary science project to properly manage the data that are collected during the experiment is critical to the effective conduct of science. When the project becomes large, possibly including several scenes of large-format remotely sensed imagery shared by many investigators requiring several services, the data management effort can involve extensive staff and computerized data inventories. The OTTER (Oregon Transect Ecosystem Research) project was supported by the PLDS (Pilot Land Data System) with several data management services, such as data inventory, certification, and publication. After a brief description of these services, experiences in providing them are compared with earlier data management efforts and some conclusions regarding data management in support of interdisciplinary science are discussed. In addition to providing these services, a major goal of this data management capability was to adopt characteristics of a pro-active attitude, such as flexibility and responsiveness, believed to be crucial for the effective conduct of active, interdisciplinary science. These are also itemized and compared with previous data management support activities. Identifying and improving these services and characteristics can lead to the design and implementation of optimal data management support capabilities, which can result in higher quality science and data products from future interdisciplinary field experiments.

Angelici, Gary↗
NASA NTRS1999

Measuring Tropospheric Winds from Space Using a Coherent Doppler Lidar Technique

The global measurement of tropospheric wind profiles has been cited by the operational meteorological community as the most important missing element in the present and planned observing system. The most practical and economical method for obtaining this measurement is from low earth orbit, utilizing a Doppler lidar (laser radar) technique. Specifically, this paper will describe the coherent Doppler wind lidar (CDWL) technique, the design and progress of a current space flight project to fly such a system on the Space Shuttle, and plans for future flights of similar instruments. The SPARCLE (SPAce Readiness Coherent Lidar Experiment) is a Shuttle-based instrument whose flight is targeted for March, 2001. The objectives of SPARCLE are three-fold: Confirm that the coherent Doppler lidar technique can measure line-of-sight winds to within 1-2 m/s accuracy; Collect data to permit validation and improvement of instrument performance models to enable better design of future missions; and Collect wind and backscatter data for future mission optimization and for atmospheric studies. These objectives reflect the nature of the experiment and its program sponsor, NASA's New Millennium Program. The experiment is a technology validation mission whose primary purpose is to provide a space flight validation of this particular technology. (It should be noted that the CDWL technique has successfully been implemented from ground-based and aircraft-based platforms for a number of years.) Since the conduct of the SPARCLE mission is tied to future decisions on the choice of technology for free-flying, operational missions, the collection of data is intrinsically tied to the validation and improvement of instrument performance models that predict the sensitivity and accuracy of any particular present or future instrument system. The challenges unique to space flight for an instrument such as SPARCLE and follow-ons include: Obtaining the required lidar sensitivity from the long distance of orbit height to the lower atmosphere; Maintaining optical alignments after launch to orbit, and during operations in "microgravity"; Obtaining pointing knowledge of sufficient accuracy to remove the speed of the spacecraft (and the rotating Earth) from the measurements; Providing sufficient power (not a problem on the Shuttle) and cooling to the instrument. The paper will describe the status and challenges of the SPARCLE project, the value of obtaining wind data from orbit, and will present a roadmap to future instruments for scientific research and operational meteorology.

Miller, Timothy L.↗
NASA NTRS1990

Computational analysis of flow in 3D propulsive transition ducts

A numerical analysis of fully three dimensional, statistically steady flows in propulsive transition ducts being considered for use in future aircraft of higher maneuverability is investigated. The purpose of the transition duct is to convert axisymmetric flow from conventional propulsion systems to that of a rectangular geometry of high aspect ratio. In an optimal design, the transition duct would be of minimal length in order to reduce the weight penalty, while the geometrical change would be gradual enough to avoid detrimental flow perturbations. Recent experiments conducted at the Propulsion Aerodynamics Branch have indicated that thrust losses in ducts of superelliptic cross-section can be surprisingly low, even if flow separation occurs near the divergent walls. In order to address the objective of developing a rational design procedure for optimal transition ducts, it is necessary to have available a reliable computational tool for the analysis of flows achieved in a sequence of configurations. Current CFD efforts involving complicated geometries usually must contend with two separate but interactive aspects: namely, grid generation and flow solution. The first two avenues of the present investigation were comprised of suitable grid generation for a class of transition ducts of superelliptic cross-section, and the subsequent application of the flow solver PAB3D to this geometry. The code, PAB3D, was developed as a comprehensive tool for the solution of both internal and external high speed flows. The third avenue of investigation has involved analytical formulations to aid in the understanding of the nature of duct flows, and also to provide a basis of comparison for subsequent numerical solutions. Numerical results to date include the generation of two preliminary grid systems for duct flows, and the initial application of PAB3D to the corresponding geometries, which are of the class tested experimentally.

Sepri, Paavo↗
DOE OSTI2024

A Gaussian process based surrogate approach for the optimization of cylindrical targets

Simulating direct-drive inertial confinement experiments presents significant computational challenges, both due to the complexity of the codes required for such simulations and the substantial computational expense associated with target design studies. Machine learning models, and in particular, surrogate models, offer a solution by replacing simulation results with a simplified approximation. In this study, we apply surrogate modeling and optimization techniques that are well established in the existing literature to one-dimensional simulation data of a new cylindrical target design containing deuterium–tritium fuel. These models predict yields without the need for expensive simulations. We find that Bayesian optimization with Gaussian process surrogates enhances sampling efficiency in low-dimensional design spaces but becomes less efficient as dimensionality increases. Nonetheless, optimization routines within two-dimensional and five-dimensional design spaces can identify designs that maximize yield, while also aligning with established physical intuition. Optimization routines, which ignore constraints on hydrodynamic instability growth, are shown to lead to unstable designs in 2D, resulting in yield loss. However, routines that utilize 1D simulations and impose constraints on the in-flight aspect ratio converge on novel cylindrical target designs that are stable against hydrodynamic instability growth in 2D and achieve high yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1986

Broadcasting satellite service synthesis using gradient and cyclic coordinate search procedures

Two search techniques are considered for solving satellite synthesis problems. Neither is likely to find a globally optimal solution. In order to determine which method performs better and what factors affect their performance, we design an experiment and solve the same problem under a variety of starting solution configuration-algorithm combinations. Since there is no randomization in the experiment, we present results of practical, rather than statistical, significance. Our implementation of a cyclic coordinate search procedure clearly finds better synthesis solutions than our implementation of a gradient search procedure does with our objective of maximizing the minimum C/I ratio computed at test points on the perimeters of the intended service areas. The length of the available orbital arc and the configuration of the starting solution are shown to affect the quality of the solutions found.

Reilly, C. H.↗
NASA NTRS1986

Broadcasting satellite service synthesis using gradient and cyclic coordinate search procedures

Two search techniques are considered for solving satellite synthesis problems. Neither is likely to find a globally optimal solution. In order to determine which method performs better and what factors affect their performance, an experiment is designed and the same problem is solved under a variety of starting solution configuration-algorithm combinations. Since there is no randomization in the experiment, results of practical, rather than statistical, significance are presented. Implementation of a cyclic coordinate search procedure clearly finds better synthesis solutions than implementation of a gradient search procedure does with the objective of maximizing the minimum C/I ratio computed at test points on the perimeters of the intended service areas. The length of the available orbital arc and the configuration of the starting solution are shown to affect the quality of the solutions found.

Reilly, C. H.↗
NASA NTRSDate not supplied

Scaled Aeroelastic Wind Tunnel Model Design with Topology Optimization

The goal of this work is to use numerical aeroelastic topology optimization to design flutter models to be tested in the Transonic Dynamics Tunnel, as part of an envisioned validation experiment for transonic flutter. The topological design develops the structural details of a variable-thickness aluminum plate located at the camber line of a scaled transport aircraft model, in order to satisfy the various conflicting design requirements, including a prescribed flutter boundary, flutter frequency, and static stress levels. Four designs are demonstrated here, where it is shown that the simultaneous design of a cylindrical tip store can help ease the conflict between low stiffness (to allow a wing to flutter in the tunnel envelope) and high strength (to ensure safe structural response). The tip store complicates the geometrical features of the wing, however, and is generally undesirable from the vantage point of a validation experiment.

Aeroelasticity↗
DOE OSTI2025

Advances in Modeling Capabilities for Critical Mineral Separation Technologies: A PrOMMiS Overview

This is an oral presentation at the TechConnect conference on the work developed by PrOMMiS. PrOMMiS builds on and extends capabilities developed within the Department of Energy’s (DOE) Institute for the Design of Advanced Energy Systems (IDAES), Integrated Platform, and Water Treatment Technoeconomic Assessment Platform (WaterTAP), which have been successfully leveraged by other Department of Energy research areas. The open-source toolkit facilitates validation, reproducibility, and accountability, allowing for easy extension of the framework to other systems. This talk presents an overview of the PrOMMiS capabilities, including unit model library, advances in thermophysical properties models, and capital cost libraries for simulation and optimization of mineral processing technologies. The PrOMMiS applications include (1) conceptual design and superstructure optimization for screening different process configurations and identifying promising technologies; (2) dynamic modeling and optimization to enable the creation of digital twins; (3) surrogate modeling tools to leverage data when predictive thermodynamic models are not currently available; (4) technical risk reduction via uncertainty quantification and robust optimization to identify process designs that are robust to process variability and uncertainties; and (5) deployment of uncertainty quantification tools to maximize knowledge gained from experimental campaigns, while reducing the number of experiments required

critical minerals and materials↗
NASA NTRS2002

Maximizing Macromolecule Crystal Size for Neutron Diffraction Experiments

A challenge in neutron diffraction experiments is growing large (greater than 1 cu mm) macromolecule crystals. In taking up this challenge we have used statistical experiment design techniques to quickly identify crystallization conditions under which the largest crystals grow. These techniques provide the maximum information for minimal experimental effort, allowing optimal screening of crystallization variables in a simple experimental matrix, using the minimum amount of sample. Analysis of the results quickly tells the investigator what conditions are the most important for the crystallization. These can then be used to maximize the crystallization results in terms of reducing crystal numbers and providing large crystals of suitable habit. We have used these techniques to grow large crystals of Glucose isomerase. Glucose isomerase is an industrial enzyme used extensively in the food industry for the conversion of glucose to fructose. The aim of this study is the elucidation of the enzymatic mechanism at the molecular level. The accurate determination of hydrogen positions, which is critical for this, is a requirement that neutron diffraction is uniquely suited for. Preliminary neutron diffraction experiments with these crystals conducted at the Institute Laue-Langevin (Grenoble, France) reveal diffraction to beyond 2.5 angstrom. Macromolecular crystal growth is a process involving many parameters, and statistical experimental design is naturally suited to this field. These techniques are sample independent and provide an experimental strategy to maximize crystal volume and habit for neutron diffraction studies.

Judge, R. A.↗
NASA NTRS1999

A Computational/Experimental Study of Two Optimized Supersonic Transport Designs and the Reference H Baseline

Two supersonic transport configurations designed by use of non-linear aerodynamic optimization methods are compared with a linearly designed baseline configuration. One optimized configuration, designated Ames 7-04, was designed at NASA Ames Research Center using an Euler flow solver, and the other, designated Boeing W27, was designed at Boeing using a full-potential method. The two optimized configurations and the baseline were tested in the NASA Langley Unitary Plan Supersonic Wind Tunnel to evaluate the non-linear design optimization methodologies. In addition, the experimental results are compared with computational predictions for each of the three configurations from the Enter flow solver, AIRPLANE. The computational and experimental results both indicate moderate to substantial performance gains for the optimized configurations over the baseline configuration. The computed performance changes with and without diverters and nacelles were in excellent agreement with experiment for all three models. Comparisons of the computational and experimental cruise drag increments for the optimized configurations relative to the baseline show excellent agreement for the model designed by the Euler method, but poorer comparisons were found for the configuration designed by the full-potential code.

Cliff, Susan E.↗
NASA NTRS1979

The role of thermophysics in the design, optimization and understanding of semiconductor crystal growth in space

The compound semiconductor material PbSnTe has been investigated by NASA Langley Research Center as part of the Material Processing in Space (MPS) experiment in the framework of the Space Shuttle program. The long-range goal of the research is the improving of the performance of infrared detectors for use in remote sensing experiments. Three distinct techniques will be used in the low-g environment of space: two techniques involving bulk growth from melt and a vapor growth technique. In order to establish realistic estimates of the required time for experiments and to determine the thermal gradients that will be required to avoid constitutional supercooling, the diffusion coefficients must be accurately measured, however more data especially in the vapor-solid phase relations are needed.

Crouch, R. K.↗
DOE OSTI2024

Development and Experimental Optimization of High-Temperature Modeling Tools and Methods for Concentrated Solar Power Particle - Systems

A novel, open-source radiative modeling toolset was developed to extend the functionality of particle-based modeling software (e.g. discrete element method (DEM)) to environmental conditions relevant to concentrated solar power applications. This toolset was optimized for deployment on desktop workstations instead of high-performance computing systems, to render such tools more accessible to the research community. Both particle-based modeling and radiative exchange modeling are computationally expensive and often require specialized programming expertise, making these methods cumbersome to use. Recent developments in DEM software by DCS Computing have greatly reduced these challenges, providing a graphical-user-interface based platform and modeling optimization for desktop workstations, HPCs, and cloud computing. The University of Dayton leveraged the experience of DCS Computing in developing a user-friendly, open-source radiative heat transfer expansion for DEM modeling. The University of Dayton DEM+ radiative modeling toolset was developed using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures and flow conditions. The toolset provides researchers with access to multiple radiative models including an accelerated Monte-Carlo Ray Tracing (application agnostic, highly computationally expensive), an expanded database of distance-based approximations (application limited, computationally light), and a weighted blending of the two methods capable of achieving over 90% reduction in computation time with equivalent accuracy compared to Monte-Carlo Ray Tracing. Through a graphical user interface, users can customize the radiative models to match their desired accuracy and available computational resources, improving access to particle based modeling for the research community. Ceramic sintered bauxite proppants were used in modeling and experimentally as a baseline. Both the radiative heat transfer and flow properties for particulate systems were investigated at elevated temperatures up to 800 °C. The major accomplishments for this work include a verified, open-source radiative modeling toolset to be distributed amongst the research community and the fabrication of three small-scale test facilities to investigate particle behavior and tune DEM flow properties for operation up to 800 °C. The findings have been shared with the research community via conference modeling workshops, deployment of the tools in DCS Computing Aspherix®, and open-source access to the developed radiative modeling tool. The development of next-generation CSP facilities and thermal energy storage systems based on ceramic particles requires providing access to computationally efficient and accurate modeling tools. Particles will experience a wide range of environments (20-800 °C) and handling conditions (dilute curtains or dense packing), requiring specially designed and optimized equipment. Optimizing solid particle physics models and establishing best-practices for particle modeling in CSP environments will assist researchers with designing optimized equipment, accelerating the deployment of more economically-competitive CSP facilities.

14 SOLAR ENERGY↗
DOE OSTI2026

Consequential improvement acquisition function for efficient multi-fidelity Bayesian optimization

Abstract Surrogate-based Bayesian optimization has been widely applied in design optimization to increase sampling efficiency. However, the cost for each evaluation of the objective function can still be very high when physical experiments or large-scale simulations are involved. Multi-fidelity Bayesian optimization is the new approach to further improve the sampling efficiency by reducing the number of expensive samples at the highest fidelity level and supplementing them with less expensive ones at low-fidelity levels. In this paper, a new consequential improvement (CI) acquisition function is proposed to allow for the simultaneous selection of the solution and the fidelity level in problems with a known hierarchy of fidelity levels. The new CI acquisition function incorporates the consequential effectiveness of objective improvement with the considerations of cost, accuracy, and validity differences between high- and low-fidelity samples in engineering practice. The new method of multi-fidelity Bayesian optimization based on the CI is demonstrated with several analytical and simulation-based design examples. In the simulation-based design optimization example, the results show that the CI acquisition function has a decisive advantage in the sampling efficiency over the other methods of multi-fidelity Bayesian optimization with simultaneous selection. The results indicate that the proposed method is particularly advantageous in solving high-dimensional problems and when large cost ratios between high- and low-fidelity evaluations exist and high-fidelity validation is mandatory. Furthermore, the method robustly avoids the prevalent issue of over sampling at low-fidelity levels.

Aydogdu, Ibrahim [Georgia Institute of Technology,↗
DOE OSTI2024

AI-assisted detector design for the EIC (AID(2)E)

Artificial Intelligence is poised to transform the design of complex, large-scale detectors like ePIC at the future Electron Ion Collider. Featuring a central detector with additional detecting systems in the far forward and far backward regions, the ePIC experiment incorporates numerous design parameters and objectives, including performance, physics reach, and cost, constrained by mechanical and geometric limits. This project aims to develop a scalable, distributed AI-assisted detector design for the EIC (AID(2)E), employing state-of-the-art multiobjective optimization to tackle complex designs. Supported by the ePIC software stack and using G EANT 4 simulations, our approach benefits from transparent parameterization and advanced AI features. The workflow leverages the PanDA and iDDS systems, used in major experiments such as ATLAS at CERN LHC, the Rubin Observatory, and sPHENIX at RHIC, to manage the compute intensive demands of ePIC detector simulations. Tailored enhancements to the PanDA system focus on usability, scalability, automation, and monitoring. Ultimately, this project aims to establish a robust design capability, apply a distributed AI-assisted workflow to the ePIC detector, and extend its applications to the design of the second detector (Detector-2) in the EIC, as well as to calibration and alignment tasks. Additionally, we are developing advanced data science tools to efficiently navigate the complex, multidimensional trade-offs identified through this optimization process.

97 MATHEMATICS AND COMPUTING↗