SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Small-signal diodes are placed in series with light-emitting diodes (LED's) to stabilize LED output against temperature fluctuations. Simple inexpensive method compensates for thermal fluctuations over a broad temperature range. Requiring few components, technique is particularly useful where circuit-board space is limited.
A trade study was performed on twenty-one digital output interface schemes for gas turbine electronic controls to select the most promising scheme based on criteria of reliability, performance, cost, and sampling requirements. The most promising scheme, a digital effector with optical feedback of the fuel metering valve position, was designed.
The turbine developed design specific work output at design speed at a total pressure ratio of 6.745 with a corresponding efficiency of 0.855. The efficiency (0.855)was 3.1 points lower than the estimated efficiency quoted by the contractor in the design report and 0.7 of a point lower than that determined by a reference prediction method. The performance of the turbine, which was a forced vortex design, agreed with the performance determined by the prediction method to about the same extent as did the performance of three reference high stage loading factor turbines, which were free vortex designs.
The design and development of a 200-watt-output, traveling-wave tube (TWT) for the Communications Technology Satellite (CTS) is discussed, with emphasis on the design evolution during the manufacturing phase of the development program. Possible further improvements to the tube design are identified.
A multivariable control design procedure based on output feedback regulator (OFR) theory is applied to the F100 turbofan engine. Results for the OFR design are compared to a design based on linear quadratic regulator (LQR) theory. The OFR feedback control is designed in the full order state space and thus eliminates any need for model reduction techniques. Using the performance measure and control structure of the LQR design, an equivalent OFR feedback control is obtained. The flexibility of the OFR as a control design procedure is demonstrated, and differing feedback control structures are evaluated.
Spectral measurements of daily, total horizontal radiation were analyzed to determine the magnitude and character of the effects in silicon cell output. Data for different seasons and weather conditions are included. Techniques and results are described.
A multivariable control design procedure based on the output feedback regulator formulation is described and applied to turbofan engine model. Full order model dynamics, were incorporated in the example design. The effect of actuator dynamics on closed loop performance was investigaged. Also, the importance of turbine inlet temperature as an element of the dynamic feedback was studied. Step responses were given to indicate the improvement in system performance with this control. Calculation times for all experiments are given in CPU seconds for comparison purposes.
This paper presents the design of digital rebalance loops for a tuned-rotor gyro which is intended to be an attitude sensor in a strapdown inertial measurement unit. A tuned-rotor gyro is a two-degree-of-freedom gyro which has two input axes, with cross-coupling between them. The rebalance loop of the gyro serves for two purposes. First, it restores the position of the rotor to its null position after experiencing an attitude input. Second, the rebalancing signal, which is proportional to the attitude change, is calibrated to give the desired attitude information. Since the gyro has more than one input and one output, a multivariable control technique is needed for designing the rebalance loop. The analytic model for the gyro is described and the available design methods are examined. A new root-locus design technique specially developed for the present problem is outlined. The design of the rebalance loop using the new technique is given. The computer simulation result of the designed system is presented and discussed.
Mechanical sequencing device produces cyclic rotations of two outputs from single cyclic rotary input. Device is useful in automatic assemble apparatus, in food-processing machinery, and as controller for sequentially operated valves.
The theory of output vector feedback (a few measured quantities) is used to derive completely active oscillation isolation functions for helicopters. These feedback controller concepts are tested with various versions of the BO 105 helicopter and their performance is demonstrated. A compensation of the vibrational excitations from the rotor and harmonics of the number of blades are considered. There is also a fast and automatic trim function for maneuvers.
A program was conducted to develop an innovative digital output interface device, a digital effector with optical feedback of the fuel metering valve position, for future electronic controls for gas turbine engines. A digital effector (on-off solenoids driven directly by on-off signals from a digital electronic controller) with optical position feedback was fabricated, coupled with the fuel metering valve, and tested under simulated engine operating conditions. The testing indicated that a digital effector with optical position feedback is a suitable candidate, with proper development for future digital electronic gas turbine controls. The testing also identified several problem areas which would have to be overcome in a final production configuration.
The SPATL is an analysis program in the Accuracy Assessment Software System which makes comparisons between ground truth information and dot labeling for an individual segment. In order to facilitate the aggregation cf this information, SPATL was modified to produce a disk output file containing the necessary information about each segment.
A description of the methods used to measure component temperatures and heat-rejection rates in a simulated space environment on output stage tubes (OST's) developed for the Communications Technology Satellite is presented along with summaries of experimentally determined values. The OST's were operated over the entire anticipated operating drive range, from the dc beam (zero drive) condition to the 6-db overdrive condition. The baseplate temperature was varied from -10 to 58 C with emphasis placed on the testing done at 45 C, the normal anticipated operating temperature. The heat-rejection rate of the OST baseplate ranged from 7.6 W at the dc beam condition to 184.5 W at the 6-db overdrive condition; the heat-rejection rate of the multistage depressed collector (MDC) cover ranged from 192.2 to 155.9 W for the same conditions. The maximum OST temperature measured on the MDC cover was 227 C during a dc beam test. The minimum temperature measured, also on the MDC cover, was -67.5 C at the end of an extended simulated eclipse test period. No effects were observed on the OST thermal characteristics due to vibration testing or temperature-reversal cycle testing.
A multivariable control design procedure based on output feedback regulator (OFR) theory is applied to the F100 turbofan engine. Results for the OFR design are compared to a design based on linear quadratic regulator (LQR) theory. This LQR design was obtained as part of the F100 Multivariable Control Synthesis (MVCS) program. In the MVCS program the LQR feedback control was designed in a reduced dimension state space and then applied to the original system. However, the OFR feedback control is designed in the full order state space and thus eliminates any need for model reduction techniques. Using the performance measure and control structure of the MVCS program LQR design, an equivalent OFR feedback control is obtained. The flexibility of the OFR as a control design procedure is demonstrated and differing feedback control structures are evaluated.
A multivariable control design procedure based on the output feedback regulator formulation is described and applied to an F100 turbofan engine model. Full order model dynamics, are incorporated in the example design. The effect of actuator dynamics on closed loop performance is investigated. Also, the importance of turbine inlet temperature as an element of the dynamic feedback is studied. Step responses are given to indicate the improvement in system performance with this control. Calculation times for all experiments are given in CPU seconds for comparison purposes.
An invention to be used for controlling aircraft flaps is described. It is applicable to control systems with two coaxial output units which pivot simultaneously with respect to two fixed units and which are activated by two opposed, straight coaxial jacks.
Solar-array voltage-current curves are calculated by assuming the existence of parasitic loads that consist of local currents of charged particles collected by the array. Three cases of interest are calculated to demonstrate how the distribution and magnitude of parasitic currents affect output. Solar array performance degradation became significant when the total parasitic current plus the load current exceeded the short-circuit current. Approximate graphical methods were useful for many applications. Power loss, which was calculated by summing the product of parasitic current and the local potential, underestimated the loss in maximum power.
A method of order reduction in singular perturbation problems due to Chow and Kokotovic is studied. The method is used for an output regulator problem in control theory. The quadratic term in the asymptotic expansion of Chow and Kokotovic is calculated and it is shown by some examples how this term can give evidence of the accuracy of the procedure.