Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxide solid electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Status and Targets for Polymer-Based Solid-State Batteries for Electric Vehicle Applications

There is growing interest in the development of Li-metal-based solid state batteries, driven by their promise in improving the energy density to satisfy electric vehicle requirements. In this work, we examine the status of Solid polymer electrolytes (SPEs) based solid state batteries for electric vehicle applications using a continuum scale mathematical model. We examine LiFePO4(LFP) cathode/lithium metal anode batteries containing three different electrolytes, namely (1) a liquid electrolyte, (2) the polystyrene-b-poly(ethylene oxide) (SEO) block copolymer electrolyte, and (3) a single-ion conducting (SIC) block copolymer electrolyte, with the liquid electrolyte serving as the baseline for the comparison. By using an optimization procedure, we assemble "virtual" batteries to identify the optimal design that maximizes energy density while allowing the power requirements of electric vehicles (EVs) to be satisfied. Results show the present status of different SPEs are still below what is considered acceptable and further improvements are needed to achieve electric vehicle targets. The optimization studies conducted here show that for low transference number electrolytes (similar to 0.2) the conductivity target is 5 x 10(-3)S cm(-1), while for a unity transference number electrolyte this target decreases to 4 x 10(-4)S cm(-1). These targets provide guidance for polymer synthesis researchers to develop better polymers for use in EVs.

25 ENERGY STORAGE↗
DOE OSTI2022

Difluorophosphoric Acid Generation and Crossover Reactions in LiNixCoyMnzO 2 Cathodes Operating at High Voltage

Cycling lithiated metal oxides to high potential (>4.5 V vs Li) is of significant interest for the next generation of lithium ion batteries as this significantly increases the capacity and energy of cells. However, cells cycled to high potential suffer from rapid capacity fade due to a combination of thickening of the anode solid electrolyte interphase (SEI) and impedance growth on the cathode. While transition metal catalysed degradation of the anode SEI has been widely proposed as a primary source of capacity loss, a related acid induced degradation of the anode SEI is proposed. A systematic investigation of LiNi 0.5 Co 0.2 Mn 0.3 O 2 , and LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes cycled to 4.2 and 4.6 V has been conducted and the oxidative generation of the strong acid difluorophosphoric acid (F 2 PO 2 H) has been quantified by solution Nuclear Magnetic Resonance (NMR) spectroscopy. Ex-situ surface analysis of the electrodes with X-ray Photo Electron spectroscopy (XPS) suggests that the generation of F 2 PO 2 H correlates with a thickening of the anode SEI and an increase in the fluorophosphate content of the SEI. Changes to the LiNi 0.8 Co 0.1 Mn 0.1 O 2 surface for cells cycled to 4.6 V are also consistent with the generation of acidic species. There is good correlation between the concentration F 2 PO 2 H, anode SEI degradation and the capacity loss of the cells.

25 ENERGY STORAGE↗
DOE OSTI2024

Solid-State, Single-Ion Conducting, Polymer Blend Electrolytes with Enhanced Li + Conduction, Electrochemical Stability, and Limiting Current Density

The development of solid-state polymer electrolytes with high lithium conductivity is crucial to improve lithium-ion battery performance and ameliorate the safety challenges associated with current solvent-based electrolytes. Unfortunately, sluggish polymer segmental dynamics are known to constrain conductivity enhancements in solid-state polymer electrolyte systems, limiting overall performance. In this work, a glassy single-ion-conducting polymer, poly[lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate] (PLiMTFSI), was blended with a flexible polymer, poly(oligo-oxyethylene methyl ether methacrylate) (POEM), and the impact of PLiMTFSI molecular weight and ion concentration on the thermal and ion-conducting behavior of blend electrolytes was investigated. High ionic conductivities approaching 1 × 10 -2 S/cm at 150 °C were realized in this polymer blend electrolyte system as a result of decoupling Li + transport from polymer segmental dynamics. The decoupled ion transport was attributed to the packing frustration of the glassy PLiMTFSI – sufficient percolating free volume was generated to produce effective ion diffusion pathways. This decoupling was tunable as the ion transport could be altered from being closely coupled to the polymer segmental dynamics (Vogel–Tammann–Fulcher-like) to hopping (Arrhenius-like) by increasing the PLiMTFSI molecular weight and ion concentration. Moreover, the immobilized TFSI anion resulted in high Li + selectivity (Li + transference number = 0.9), high electrochemical stability (up to 4.7 V against Li + / Li), and limiting current density of 1.8 mA/cm 2 (electrolyte thickness = 0.05 cm). These features suggest that this single-ion-conducting, polymer blend electrolyte might be a promising alternative to a benchmark system – salt-doped polyethylene oxide. Moreover, the above characteristics can support the battery operation at higher voltages using energy-dense Li metal anodes, with faster charging rates and enhanced energy/power densities. Altogether, the results suggest that polymer chain packing frustration can be exploited to overcome the constraints of slow polymer segmental relaxations to achieve rapid and highly selective ion transport and enhanced performance in solid-state polymer electrolytes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

X-ray Diffraction Studies of Single-Crystal Materials for Broad Battery Applications

Single-crystal materials have attracted growing interest in battery research due to their well-defined crystallographic orientation, absence of grain boundaries, and enhanced mechanical and electrochemical stability. This Review provides a comprehensive overview of recent advances in the synthesis, structural evolution, and performance optimization of single-crystal electrodes and solid electrolytes. Particular focus is placed on the application of advanced X-ray diffraction (XRD) techniques, including operando synchrotron diffraction, reciprocal space mapping, and Bragg coherent diffraction imaging, which have enabled in-depth investigations of lattice strain, cation disorder, phase transitions, and defect formation. Representative case studies across Ni-rich layered oxides, spinel-type cathodes, and garnet-based electrolytes are examined to highlight the structural features unique to single crystals. Additionally, the synergistic integration of XRD with machine learning, tomography, and spectroscopy is discussed as a powerful direction for real-time analysis and predictive modeling. Furthermore, these insights provide critical guidance for the rational design of high-performance single-crystal materials in lithium, sodium, and solid-state battery systems.

25 ENERGY STORAGE↗
NASA NTRS1987

Perovskite oxides: Oxygen electrocatalysis and bulk structure

Perovskite type oxides were considered for use as oxygen reduction and generation electrocatalysts in alkaline electrolytes. Perovskite stability and electrocatalytic activity are studied along with possible relationships of the latter with the bulk solid state properties. A series of compounds of the type LaFe(x)Ni1(-x)O3 was used as a model system to gain information on the possible relationships between surface catalytic activity and bulk structure. Hydrogen peroxide decomposition rate constants were measured for these compounds. Ex situ Mossbauer effect spectroscopy (MES), and magnetic susceptibility measurements were used to study the solid state properties. X ray photoelectron spectroscopy (XPS) was used to examine the surface. MES has indicated the presence of a paramagnetic to magnetically ordered phase transition for values of x between 0.4 and 0.5. A correlation was found between the values of the MES isomer shift and the catalytic activity for peroxide decomposition. Thus, the catalytic activity can be correlated to the d-electron density for the transition metal cations.

Carbonio, R. E.↗
NASA NTRS1988

Perovskite-type oxides - Oxygen electrocatalysis and bulk structure

Perovskite type oxides were considered for use as oxygen reduction and generation electrocatalysts in alkaline electrolytes. Perovskite stability and electrocatalytic activity are studied along with possible relationships of the latter with the bulk solid state properties. A series of compounds of the type LaFe(x)Ni1(-x)O3 was used as a model system to gain information on the possible relationships between surface catalytic activity and bulk structure. Hydrogen peroxide decomposition rate constants were measured for these compounds. Ex situ Mossbauer effect spectroscopy (MES), and magnetic susceptibility measurements were used to study the solid state properties. X ray photoelectron spectroscopy (XPS) was used to examine the surface. MES has indicated the presence of a paramagnetic to magnetically ordered phase transition for values of x between 0.4 and 0.5. A correlation was found between the values of the MES isomer shift and the catalytic activity for peroxide decomposition. Thus, the catalytic activity can be correlated to the d-electron density for the transition metal cations.

Carbonio, R. E.↗
NASA NTRS2019

Evaluation Studies of Solid Oxide-Based Fuel Cells for Light-Weight Electrical Power in Aviation: Concepts and Opportunities for the Application of Additive Manufacturing

Currently NASA is investigating the feasibility of hybrid-electric, solid oxide fuel cell power (SOFC) systems for generating electrical power for airborne propulsion and secondary/auxiliary power. As part of this project, researchers are investigating the performance of SOFC hardware in aviation-like environments, to establish the barriers, and potential suitability, of this technology. Immediate findings indicate the unsuitability of current SOFC stack architectures with regards to ease of manufacture, specific energy, as well as environmental and mechanical durability. One possible solution is to create light-weight high specific energy density solid oxide fuel cells. The possibility may be achievable by the use of modern processing techniques such as additive manufacturing. Here I discuss the use additive manufacturing to fabricate ceramic anode, electrolytes, and cathode cells supported on various metal foams with predicted performance based upon variable porosities

Goldsby, Jon C.↗
DOE OSTI2024

Mechanically and Thermally Robust Gel Electrolytes Built from A Charged Double Helical Polymer

Polymer electrolytes have received tremendous interest in the development of solid-state batteries, but often fall short in one or more key properties required for practical applications. Herein, a rigid gel polymer electrolyte prepared by immobilizing a liquid mixture of a lithium salt and poly(ethylene glycol) dimethyl ether with only 8 wt% poly(2,2′-disulfonyl-4,4′-benzidine terephthalamide) (PBDT) is reported. The high charge density and rigid double helical structure of PBDT lead to formation of a nanofibrillar structure that endows this electrolyte with stronger mechanical properties, wider temperature window, and higher battery rate capability compared to all other poly(ethylene oxide) (PEO)-based electrolytes. The ion transport mechanism in this rigid polymer electrolyte is systematically studied using multiple complementary techniques. Li/LiFePO 4 cells show excellent capacity retention over long-term cycling, with thermal cycling reversibility between ambient temperature and elevated temperatures, demonstrating compelling potential for solid-state batteries targeting fast charging at high temperatures and slower discharging at ambient temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Surface Engineering Strategy to Synthesize Bicomponent Carbons for Rechargeable Zinc-Air Batteries

Atomic Fe-N x moieties and nanosized FeCo species anchored on carbons have each been demonstrated to be among the most effective active components for oxygen reduction and evolution reactions (ORR/OER), respectively in rechargeable zinc -air batteries (ZABs). However, incorporating both of these components in a single catalyst presents a great challenge due to the trade-off in formation between them during hightemperature preparation. Herein, we integrate them into a bicomponent carbon through a surface engineering strategy. In this process, K 3 [Fe(CN) 6 ] is engineered on the surface of a precursor mixture consisting of polyaniline-coated graphene oxide and ZIF-67. This is followed by pyrolysis to produce the bicomponent carbon catalyst of FeCo nanoparticles modified carbon polyhedron (for accelerating the OER), supported on atomically dispersed Fe -N -doped carbon nanosheet (for boosting the ORR). The catalyst exhibits a small potential gap of 0.69 V for OER/ORR. In situ Raman spectroscopy demonstrates that spinel FeCo oxides may be responsible for OER. The use of this catalyst in ZABs achieves high power densities of 225 mW cm -2 in aqueous electrolyte and 164 mW cm -2 in solid-state electrolyte. Additionally, a small and stable voltage gap of 0.712 V at 10 mA cm -2 is maintained after 1035 discharge -charge cycles demonstrating the great application potential in energy devices.

An, Jia-Xing↗
DOE OSTI2021

Orientation-Dependent Distortion of Lamellae in a Block Copolymer Electrolyte under DC Polarization

Lithium-salt-doped block copolymers have the potential to serve as solid electrolytes in rechargeable batteries with lithium metal anodes. In this work, we use small-angle X-ray scattering (SAXS) to study the structure of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) doped with bis-(trifluoromethylsulfonyl)amine lithium salt (LiTFSI) during direct current (dc) polarization experiments in lithiu-lithium symmetric cells. The block copolymer studied is nearly symmetric in composition, has a total molecular weight of 39 kg mol -1 , and exhibits a lamellar morphology at all studied salt concentrations. When ionic current is passed through the electrolyte, a salt concentration gradient forms that induces a spatial gradient in the domain spacing, d. The dependence of d on distance from the positive electrode, x, was determined experimentally by scanning the incident X-ray beam from one lithium electrode to the other. By studying the two-dimensional (2D) SAXS patterns as a function of azimuthal scattering angle, we find that lamellae with PS/PEO interfaces oriented perpendicular to the flow of ionic current (LAM ⟂ ) swell and contract to a greater degree than those with interfaces oriented parallel to the current direction (LAM || ). While domains with the LAM ⟂ do not provide direct conducting pathways between the electrodes, our analysis suggests that they play an important role in establishing the salt concentration gradient necessary for sustaining a large ionic current through greater expansion and contraction.

25 ENERGY STORAGE↗
DOE OSTI2024

Amorphous Oxyhalide Matters for Achieving Lithium Superionic Conduction

The recently surged halide-based solid electrolytes (SEs) are great candidates for high-performance all-solid-state batteries (ASSBs), due to their decent ionic conductivity, wide electrochemical stability window, and good compatibility with high-voltage oxide cathodes. In contrast to the crystalline phases in halide SEs, amorphous components are rarely understood but play an important role in Li-ion conduction. Here, we reveal that the presence of amorphous component is common in halide-based SEs that are prepared via mechanochemical method. The fast Li-ion migration is found to be associated with the local chemistry of the amorphous proportion. Taking Zr-based halide SEs as an example, the amorphization process can be regulated by incorporating O, resulting in the formation of corner-sharing Zr–O/Cl polyhedrons. This structural configuration has been confirmed through X-ray absorption spectroscopy, pair distribution function analyses, and Reverse Monte Carlo modeling. The unique structure significantly reduces the energy barriers for Li-ion transport. As a result, an enhanced ionic conductivity of (1.35 ± 0.07) × 10 –3 S cm –1 at 25 °C can be achieved for amorphous Li 3 ZrCl 4 O 1.5 . In addition to the improved ionic conductivity, amorphization of Zr-based halide SEs via incorporation of O leads to good mechanical deformability and promising electrochemical performance. In conclusion, these findings provide deep insights into the rational design of desirable halide SEs for high-performance ASSBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

High Performance SrFe 0.2 Co 0.4 Mo 0.4 O 3–δ Ceramic Anode Supported Low-Temperature SOFCs

The development of alternative ceramic anodes for low-temperature solid oxide fuel cells (LT-SOFCs) is essential to overcome the inherent challenges such as redox instability and coking associated with Ni-based cermet anodes. Moreover, due to the large electrolyte ohmic loss at low temperature, it is critical to developing an electrode supported cell that allows electrolyte thickness reduction. Here we successfully demonstrated a high performance SrFe 0.2 Co 0.4 Mo 0.4 O 3–δ (SFCM) ceramic anode supported LT-SOFC with a peak power density of 730 mW cm –2 and 300 mW cm –2 at ambitious low temperatures of 550 °C and 450 °C, respectively, in humidified H 2 . The new anode material SFCM exhibits exceptional conductivity of over 30 S cm –1 at 450 °C in humidified H 2 , providing essential current collection capability as an anode backbone appropriate for the infiltration of Ni-gadolinia doped ceria (GDC) electrocatalysts. Compared to conventional Ni-cermet anodes, the nano-sized Ni-GDC particles in our SFCM based electrode significantly improves the cell stability in hydrocarbon gases. We demonstrated a stable long-term operation over a period of 380 h in CH 4 –containing gas mixtures at 450 °C with a voltage degradation rate of 4% per 1000 h at a constant current of 0.2 A*cm –2 . Furthermore, our results demonstrate a high performance ceramic anode with high stability for low temperature operation.

25 ENERGY STORAGE↗
DOE OSTI2021

Li2O-Based Cathode Additives Enabling Prelithiation of Si Anodes

Low first-cycle Coulombic efficiency is especially poor for silicon (Si)-based anodes due to the high surface area of the Si-active material and extensive electrolyte decomposition during the initial cycles forming the solid electrolyte interphase (SEI). Therefore, developing successful prelithiation methods will greatly benefit the development of lithium-ion batteries (LiBs) utilizing Si anodes. In pursuit of this goal, in this study, lithium oxide (Li2O) was added to a LiNi0.6Mn0.2Co0.2O2 (NMC622) cathode using a scalable ball-milling approach to compensate for the initial Li loss at the anode. Different milling conditions were tested to evaluate the impact of particle morphology on the additive performance. In addition, Co3O4, a well-known oxygen evolution reaction catalyst, was introduced to facilitate the activation of Li2O. The Li2O + Co3O4 additives successfully delivered an additional capacity of 1116 mAh/gLi2O when charged up to 4.3 V in half cells and 1035 mAh/gLi2O when charged up to 4.1 V in full cells using Si anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Insights into Spontaneous Solid Electrolyte Interphase Formation at Magnesium Metal Anode Surface from Ab Initio Molecular Dynamics Simulations

Spontaneous chemical reactivity at multivalent (Mg, Ca, Zn, Al) electrode surfaces is critical to solid electrolyte interphase (SEI) formation, and hence, directly affects the longevity of batteries. Here, we report an investigation of the reactivity of 0.5 M Mg(TFSI)2 in 1,2-dimethoxyethane (DME) solvent at a Mg(0001) surface using ab initio molecular dynamics (AIMD) simulations and detailed Bader charge analysis. Based on the simulations, the initial degradation reactions of the electrolyte strongly depend on the structure of the Mg(TFSI)2 species near the anode surface. At the surface, the dissociation of Mg(TFSI)2 species occurs via cleavage of the N-S bond for the solvent separated ion pair (SSIP) and via cleavage of the C-S bond for the contact ion pair (CIP) configuration. In the case of the CIP, both TFSI anions undergo spontaneous bond dissociation reactions to form atomic O, C, S, F, and N species adsorbed on the surface of the Mg anode. These products indicate that the initial SEI layer formed on the surface of the pristine Mg anode consists of a complex mixture of multiple components such as oxides, carbides, sulfides, fluorides, and nitrides. We believe that the atomic level insights gained from these simulations will lay the groundwork for the rational design of tailored and functional interphases that are critical for the success of multivalent battery technology.

Agarwal, Garvit↗
DOE OSTI2026

(CrMnCoNiTi) 3 O 4 high-entropy spinel oxide as a high-performance electrode for supercapacitors

In this study, spinel-structured (CrMnCoNiTi)₃O₄ high-entropy oxides (HEOs) have been successfully synthesized using the solution combustion method, and their performance as supercapacitor electrode materials was investigated. These HEOs exhibit excellent performance, stemming from the unique high-entropy effect and lattice distortion. This structure effectively buffers volumetric strain during cycling, conferring the material with extremely high structural stability and specific capacity. The material demonstrates a high specific capacity of 491.5 C∙g⁻¹ at a current density of 0.5 A∙g⁻¹. Furthermore, it shows extraordinary cycling stability: after 10,000 charge/discharge cycles at 5 A∙g⁻¹, the capacity retention rate is 99%, and the Coulombic efficiency consistently remains close to 100%. Ex-situ structural characterizations further reveal that this excellent cycling durability originates from a cooperative multination valence reconstruction mechanism within an entropy-stabilized spinel framework. Additionally, a symmetric supercapacitor assembled using this material and 1 M KOH electrolyte successfully extended the working voltage to 1.2 V. This research highlights the great potential of high-entropy oxides in synergizing high energy density and ultra-long cycling life, laying a solid foundation for the development of next-generation high-performance supercapacitor electrode materials.

High entropy oxides↗
DOE OSTI2021

Redox-stable symmetrical solid oxide fuel cells with exceptionally high performance enabled by electrode/electrolyte diffuse interface

Here, in this study, we report a high performance and redox-stable symmetrical solid oxide fuel cell (SOFC) based on (Ba 0.5 Sr 0.5 ) (Mo 0.1 Fe 0.9 )O 3-δ (BSMF) electrode and La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ (LSGM) electrolyte. BSMF is able to operate both as anode and cathode. Excellent electrocatalytic activity has been achieved on BSMF towards hydrogen oxidation and oxygen reduction. Due to its closely matched lattice parameter to LSGM electrolyte, a unique diffuse interface is formed between BSMF and LSGM. Compared to a clean interface, e.g. BSMF/gadolinium doped ceria interface, this diffuse interface promotes the performance of BSMF electrode 1–1.8 times in 600–800 °C. Polarization resistance of the BSMF/LSGM specimen is as low as 0.047 and 0.007 Ωcm 2 in humidified H 2 and in air at 800 °C, respectively. On the BSMF/LSGM/BSMF symmetrical cell, a maximum power density of 2.28 W/cm 2 is achieved at 800 °C, the highest among with redox-stable ceramic electrodes to the best of our knowledge. Redox stability of this cell is confirmed. The role of anode and cathode is reversed back and forth in different operation modes. No apparent degradation is observed through 4 cycles within a 110 h operation period. These findings demonstrate that (Ba 0.5 Sr 0.5 ) (M o0.1 Fe 0.9 )O 3-δ coupled with LSGM electrolyte is an excellent choice to build a high performance, redox-stable SOFC.

25 ENERGY STORAGE↗