Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE RECOVERY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Free-flight Performance of a Rocket-boosted, Air-launched 16-inch-diameter Ram-jet Engine at Mach Numbers up to 2.20

The investigation of air-launched ram-jet engines has been extended to include a study of models with a nominal design free-stream Mach number of 2.40. These models require auxiliary thrust in order to attain a flight speed at which the ram jet becomes self-accelerating. A rocket-boosting technique for providing this auxiliary thrust is described and time histories of two rocket-boosted ram-jet flights are presented. In one flight, the model attained a maximum Mach number of 2.20 before a fuel system failure resulted in the destruction of the engine. Performance data for this model are presented in terms of thrust and drag coefficients, diffuser pressure recovery, mass-flow ratio, combustion efficiency, specific fuel consumption, and over-all engine efficiency.

AIR INLETS - NOSE, ANNULAR↗
NASA NTRS1953

An analytical study of the comparative performance of six air-induction systems for turbojet-powered airplanes designed to operate at Mach numbers up to 2.0

A study is presented of inlet designs and aerodynamic characteristics of air-induction systems intended for operation with a turbojet engine operating with a constant-volume air-flow process. Two-dimensional inlet designs similar to those discussed in NACA RM A52C14, plus a fixed-geometry inlet with a convergent-divergent diffuser, and an additional variable-geometry inlet are considered for Mach numbers from 0.85 to 2.0 from sea level to the stratosphere. For best performance throughout this range of Mach numbers and altitudes, it was shown that the geometry of the inlet must be such as to insure a high pressure recovery, as well as to provide for a variable entrance area. The inlets are compared on the basis of a drag evaluation neglecting viscosity.

DIFFUSERS, SUBSONIC↗
NASA NTRS1952

Analytical and Experimental Investigation of Inlet-engine Matching for Turbojet-powered Aircraft at Mach Numbers up to 2.0

An analysis of inlet-turbojet-engine matching for a range of Mach numbers up to 2.0 indicates large performance penalties when fixed-geometry inlets are used. Use of variable-geometry inlets, however, nearly eliminates th The analysis was confirmed experimentally by investigating at Mach numbers of 0, 0.63, and 1.5 to 2.0 two single oblique-shock-type inlets of different compression-ramp angles, which simulated a variable-geometry configuration. The experimental investigation indicated that total-pressure recoveries comparable withose attainable with well designed nose inlets were obtained with the side inlets when all the boundary layer ahead of the inlets was removed. Serious drag penalties resulted at a Mach number of 2.0 from the use of blunt-cowl leading edges. However, sharp-lip inlets produced large losses in thrust for the take-off condition. These thrust penalties which are associated with the the low-speed operation of the sharp-lip inlet designs can probably be avoided without impairing the supersonic performance of the inlet by the use of auxiliary inlets or blow-in doors.

Esenwein, Fred T↗
NASA NTRS1954

Summary of Free-flight Performance of a Series of Ram-jet Engines at Mach Numbers from 0.80 to 2.20

Data obtained from the NACA air-launched ram-jet program are summarized with emphasis placed upon the transonic propulsive thrust potential of the engines. Data are presented for boosted and non-boosted engine configurations which incorporate a single-oblique-shock or double-oblique-shock diffuser designed for critical inlet operation at flight Mach numbers of 1.8 and 2.4, respectively. The engines are evaluated in terms of flight Mach number, mass-flow ratio, diffuser pressure recovery, combustion-chamber heat release, propulsive thrust, external drag, and specific impulse. From specific impulse considerations, it appears that for some air-launched missile applications the self-accelerating supersonic ram jet may have a lower gross weight than a rocket-boosted ram jet.

RESEARCH EQUIPMENT, FREE-FLIGHT↗
NASA NTRS1956

Development of flow distortions in a full-scale nacelle inlet at Mach numbers 0.63 and 1.6 to 2.0

The nature of flow-distortion development in the subsonic diffuser was determined for a typical full-scale axisymmetric nose inlet at Mach numbers to 2.0 and angles of attack to -8 degrees. Inlet design variables studied included 14 degrees and 17 degrees internalcowl lip angles conical compression surfaces with and without boundary-layer removal slots, and cone tip translation. Data presented include the inlet overall pressure recovery, mass flow, and distortion at the diffuser exit. Primary emphasis in the data, however, is placed on critical inlet operation, for which the flow distortion is traced from the inlet throat to the diffuser exit.

Piercy, Thomas G↗
NASA NTRS1956

A variable-geometry annular cascade-type inlet at Mach numbers of 1.9 and 3.05

A variable-geometry annular cascade-type inlet is proposed and demonstrated. Such an inlet yielded total-pressure recoveries of 0.84 and 0.53 at Mach numbers of 1.9 and 3.05., respectively. Unity mass-flow ratios were obtained at each Mach number with only marginal subcritical stability ranges of mass-flow ratio (?0.03). Angles of attack up to 6 percent produced only moderate decreases in performance.

Connors, James F↗
NASA NTRS1957

Experimental investigation of water injection in subsonic diffuser of a conical inlet operation at free-stream Mach number of 2.5

A spike-type nose inlet with sharp-lip cowl was investigated at a free-stream Mach number of 2.5 with water injection in its 16-inch diameter, 11-foot-long subsonic diffuser section. Inlet total temperature of exit with liquid-air ratios of about 0.04 with no apparent change in the critical pressure recovery. The observed temperature drops were less than the theoretically predicted values, and the amount of water evaporated was 35 to 50 percent less than that theoretically possible.

Beke, Andrew↗
NASA NTRS1957

Comparison of effect of a turbojet engine and three cold-flow configurations on the stability of a full-scale supersonicle inlet

Increasing the volume and length of the duct behind the inlet affected the inlet stability at Mach 2.0 and zero angle of attack. Close approximation of the inlet stability limit of the J34 engine-inlet configuration was obtained by a cold-pipe configuration having a length and volume approaching that measured to the engine turbine. Variation of these parameters had a small effect on the minimum subcritical stable mass flow below a cowl-lip-position parameter of 44 degrees and appeared to have a negligible effect on the inlet pressure-recovery - mass-flow curve. Initial buzz frequency and minimum cowl-lip-position parameter for complete buzz-free operation varied with configuration.

Musial, Norman T↗
NASA NTRS1943

Review of Flight Tests of NACA C and D Cowlings on the XP-42 Airplane

Results of flight tests of the performance and cooling characteristics of three NACA D cowlings and of a conventional NACA D cowling on the XP-42 airplane are summarized and compared. The D cowling is, in general, characterized by the use of an annular inlet and diffuser section for the engine-cooling air. The D cowlings tested were a long-nose high-inlet-velocity cowling, a short-nose high-inlet-velocity cowling, and a short-nose low inlet-velocity cowling. The use of wide-chord propeller cuffs or an axial-flow fan with the D cowlings increased the cooling pressure recoveries in the climb condition at the expense of some of the improvement in speed.

Johnston, J Ford↗
NASA NTRS1950

An investigation of several NACA 1-series nose inlets with and without protruding central bodies at high-subsonic Mach numbers and at a Mach number of 1.2

An investigation of three NACA 1-series nose inlets, two of which were fitted with protruded central bodies, was conducted in the Langley 8-foot high-speed tunnel. An elliptical-nose body, which had a critical Mach number approximately equal to that of one of the nose inlets, was also tested. Tests were made near zero angle of attack for a Mach number range from 0.4 to 0.925 and for the supersonic Mach number of 1.2. The inlet-velocity-ratio range extended from zero to a maximum value of 1.34. Measurements included pressure distribution, external drag, and total-pressure loss of the internal flow near the inlet. Drag was not measured for the tests at the supersonic Mach number. Over the range of inlet-velocity ratio investigated, the calculated external pressure-drag coefficient at a Mach number of 1.2 was consecutively lower for the nose inlets of higher critical Mach number, and the pressure-drag coefficient of the longest nose inlet was in the range of pressure-drag coefficient for two solid noses of fineness ratio 2.4 and 6.0. For Mach numbers below the Mach number of the supercritical drag rise, extrapolation of the test data indicated that the external drag of the nose inlets was little affected by the addition of central bodies at or slightly below the minimum inlet-velocity ratio for unseparated central-body flow. The addition of central bodies to the nose inlets also led to no appreciable effects on either the Mach number of the supercritical drag rise, or, for inlet-velocity ratios high enough to avoid a pressure peak at the inlet lip, on the critical Mach number. The total-pressure recovery of the inlets tested, which were of a subsonic type, was sensibly unimpaired at the supersonic Mach number of 1.2 Low-speed measurements of the minimum inlet-velocity ratio for unseparated central-body flow appear to be applicable for Mach numbers extending to 1.2.

Pendley, Robert E↗
NASA NTRS1994

Installed F/A-18 inlet flow calculations at 30 degrees angle-of-attack: A comparative study

NASA Lewis is currently engaged in a research effort as a team member of the High Alpha Technology Program (HATP) within NASA. This program utilizes a specially equipped F/A-18, the High Alpha Research Vehicle (HARV), in an ambitious effort to improve the maneuverability of high-performance military aircraft at low subsonic speed, high angle of attack conditions. The overall objective of the Lewis effort is to develop inlet technology that will ensure efficient airflow delivery to the engine during these maneuvers. One part of the Lewis approach utilizes computational fluid dynamics codes to predict the installed performance of inlets for these highly maneuverable aircraft. Full Navier-Stokes (FNS) calculations on the installed F/A-18 inlet at 30 degrees angle of attack, 0 degrees yaw, and a freestream Mach number of 0.2 have been obtained in this study using an algebraic turbulence model with two grids (original and revised). Results obtained with the original grid were used to determine where further grid refinements and additional geometry were needed. In order to account properly for the external effects, the forebody, leading edge extension (LEX), ramp, and wing were included with inlet geometry. In the original grid, the diverter, LEX slot, and leading edge flap were not included due to insufficient geometry definition, but were included in a revised grid. In addition, a thin-layer Navier-Stokes (TLNS) code is used with the revised grid and the numerical results are compared to those obtained with the FNS code. The TLNS code was used to evaluate the effects on the solution using a code with more recent CFD developments such as upwinding with TVD schemes versus central differencing with artificial dissipation. The calculations are compared to a limited amount of available experimental data. The predicted forebody/fuselage surface static pressures compared well with data of all solutions. The predicted trajectory of the vortex generated under the LEX was different for each solution. These discrepancies are attributed to differences in the grid resolution and turbulence modeling. All solutions predict that this vortex is ingested by the inlet. The predicted inlet total pressure recoveries are lower than data and the distortions are higher than data. The results obtained with the revised grid were significantly improved from the original grid results. The original grid results indicated the ingested vortex migrated to the engine face and caused additional distortions to those already present due to secondary flow development. The revised grid results indicate that the ingested vortex is dissipated along the inlet duct inboard wall. The TLNS results indicate the flow at the engine face was much more distorted than the FNS results and is attributed to the pole boundary condition introducing numerical distortions into the flow field.

Smith, C. Frederic↗
NASA NTRS1992

Results of a preliminary investigation of inlet unstart on a high-speed civil transport airplane concept

The aircraft design engineer of today is tasked with satisfying an increasing number of conflicting requirements. The fact that conflict in these requirements may be technically, economically, or politically motivated usually compounds the difficulty of determining the best solution to a design issue. In this regard, propulsion/airframe integration for supersonic airplanes must rank as one of the most challenging aspects of airplane design. For the cruise Mach numbers currently being considered for High-Speed Civil Transport (HSCT) airplanes, the inlet requirements of low drag, low bleed flow, and high pressure recovery appear to be best met with a mixed-compression design. Unfortunately, these desirable attributes come with a highly undesirable companion: the inlet unstart phenomenon. Concern over the effects of a mixed-compression inlet unstart on the vehicle dynamics of large, high-speed aircraft is not new; a comprehensive wind-tunnel study addressing the problem was published in 1962. Additional investigations of the problem were made throughout the United States SST program and the follow-on NASA program into the late 1970's. The current study sought to examine the magnitude of the problem in order to determine if an inlet unstart posed a potential hazard severe enough to preclude the use of mixed-compression inlets on proposed HSCT concepts.

Domack, Christopher S.↗
NASA NTRS1994

Alpha LAMP Integration Facility

This paper describes the activity recently completed to meet the simulated space environment requirements for the ground-based testing of an integrated Space Based Laser (SBL) system experiment. The need to maintain optical alignment in the challenging dynamic environment of the pressure recovery system required to simulate space dominated the design requirements. A robust system design was established which minimized the total program costs, most notably by reducing the cost of integrating the components of the experiment. The components of the experiment are integrated on an optical bench in a clean area adjacent to the vacuum chamber and moved on air bearings into the chamber for testing.

Oshiro, Richard↗
NASA NTRS1994

Three Dimensional Compressible Turbulent Flow Computations for a Diffusing S-Duct With/Without Vortex Generators

Numerical investigations on a diffusing S-duct with/without vortex generators and a straight duct with vortex generators are presented. The investigation consists of solving the full three-dimensional unsteady compressible mass averaged Navier-Stokes equations. An implicit finite volume lower-upper time marching code (RPLUS3D) has been employed and modified. A three-dimensional Baldwin-Lomax turbulence model has been modified in conjunction with the flow physics. A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vortical structure for modeling the shed vortex is used as a source term in the computation domain. The injected vortex paths in the straight duct are compared with the analysis by two kinds of prediction models. The flow structure by the vortex generators are investigated along the duct. Computed results of the flow in a circular diffusing S-duct provide an understanding of the flow structure within a typical engine inlet system. These are compared with the experimental wall static-pressure, static- and total-pressure field, and secondary velocity profiles. Additionally, boundary layer thickness, skin friction values, and velocity profiles in wall coordinates are presented. In order to investigate the effect of vortex generators, various vortex strengths are examined in this study. The total-pressure recovery and distortion coefficients are obtained at the exit of the S-duct. The numerical results clearly depict the interaction between the low velocity flow by the flow separation and the injected vortices.

Cho, Soo-Yong↗
NASA NTRS1994

Large-eddy simulation of flow through a plane, asymmetric diffuser

A challenge for traditional turbulence modeling, based on the Reynolds averaged Navier-Stokes equations, remains the accurate prediction of 'mild', adverse pressure-gradient driven separation from a smooth surface. With this study we want to explore the capability of large-eddy simulation to predict the separation which occurs on the deflected wall of an asymmetric, plane diffuser with opening angle of 10 deg. The flow through the plane diffuser exhibits some additional interesting physical phenomena which make it a challenging test case. In addition to 'mild' separation about halfway down the deflected ramp, the flow is characterized by a small backflow zone with stalled fluid in the rear part of the expanding section. The turbulent flow entering the diffuser is subject to combined adverse and radial pressure gradients stemming from the convex curvature. Finally the flow recovers into a developed, turbulent channel flow in the outlet section. Obi et al. provide measurements of mean flow, Reynolds stresses, and pressure recovery, which were obtained by means of LDV in a wind tunnel. The objective of this study is to investigate whether LES with the standard dynamic model is able to accurately predict the flow in the one-sided diffuser and to explore the resolution requirements and associated costs.

Kaltenbach, Hans-Jakob↗
NASA NTRS1995

PARC3D calculations of the F/A-18A HARV inlet vortex generators

NASA Lewis Research Center is currently engaged in a research effort as a team member of the High Alpha Technology Program within the NASA agency. This program uses a specially-equipped F/A-18A aircraft called the High Alpha Research Vehicle (HARV), in an effort to improve the maneuverability of high performance military aircraft at low-subsonic-speed, high-angle-of-attack conditions. The overall objective of the NASA Lewis effort is to develop inlet analysis technology towards efficient airflow delivery to the engine during these maneuvers. One portion of this inlet analysis technology uses computational fluid dynamics to predict installed inlet performance. Most of the F/A-18A HARV geometry, which includes the ramp/splitter plate, side diverter and slot, inlet lip and upper diverter, and deflected leading-edge flap has been modeled. The empennage and rear fuselage have not. A pair of vortex generators located on the bottom wall of the inlet were not modeled initially. These vortex generators were installed to alleviate any flow separation that may be induced by the wheel well protrusion into the inlet wall. Calculations completed with the PARC3D code showed that the pressure recovery has been underpredicted and the flow distortion over-predicted. To improve the correlation of PARC3D predictions with flight and wind tunnel tests, the vortex generators were included in the grid geometry and the results are presented in this report. The grid totals 27 blocks or 1.3 million grid points for the half model, which includes the vortex generator grid blocks. Two flight cases were calculated, a high speed case with a Mach number of 0.8 and angle of attack of 3.4; and a low speed case with a Mach number of 0.43 and angle of attack of 32.2. The vortex generators have a significant effect on the inlet boundary layers at high speed, low angle of attack; and have no effect at low speed, high angle of attack.

Podleski, Steve D.↗
NASA NTRS1996

Experimental Investigation of the Performance of a Mach-2.7 Two-dimensional Bifurcated Duct Inlet with 30 Percent Internal Contraction

An experimental study was conducted to determine the performance of a two-dimensional, mixed-compression bifurcated duct inlet system designed for a free-stream Mach number of 2.7. Thirty percent of the supersonic area contraction occurred internally. A movable ramp was used to vary the contraction ratio for off-design operation. Boundary layer bleed regions were located on the cowl, centerbody, and sidewall surfaces. There were also provisions for vortex generators on the cowl and centerbody of the subsonic diffuser. Data were obtained over the Mach number range of 2.0 to 2.8 and at angles of yaw from 0 deg. to the maximum value prior to inlet un-start. The test at Mach 2.8 was to obtain data for an over- speed condition. The Reynolds number varied from 2.5 to 2.3 million/ft for Mach numbers above 2.5. At Mach numbers of 2.5 and lower, the Reynolds number was set at 2.5 million/ft. Bleed patterns, vortex generator patterns, and ramp position were varied, and three inlet configurations were selected for more extensive study. Two of these configurations had self-starting capability. The self-starting configuration that was developed produced 89 percent total pressure recovery at the compressor face station with 6.8 percent total bleed. The compressor face distortion was about 16 percent. Vortex generators were extremely effective in re-distributing flow but were not as effective in reducing distortion. Excellent flow symmetry was achieved between the separated halves of the inlet, and twin-duct instability was not observed. The ramp tip shock was steeper than expected. This caused the cowl lip shock to be reflected from the ramp instead of being cancelled at the shoulder. However, peak recovery at the throat was still obtained with the ramp near the design position.

Wasserbauer, J. F.↗