SEARCH · Search NASA

Results for “Power Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Icing effects on aircraft stability and control determined from flight data: Preliminary results

The effects of airframe icing on the stability and control characteristics of the NASA DH-6 Twin Otter icing research aircraft were investigated by flight test. The flight program was developed to obtain the stability and control parameters of the DH-6 in a baseline ('uniced') configuration and an 'artificially iced' configuration for specified thrust conditions. Stability and control parameter identification maneuvers were performed over a wide range of angles of attack for wing flaps retracted (0 deg) and wing flaps partially deflected (10 deg). Engine power was adjusted to hold thrust constant at one of three thrust coefficients (C(sub T) = 0.14, C(sub T) = 0.07, C(subT) = 0.00). This paper presents only the pitching- and yawing-moment results from the flight test program. Stability and control parameters were estimated for the uniced and artificially iced configurations using a modified stepwise regression algorithm. Comparisons of the uniced and iced stability and control parameters are presented for the majority of the flight envelope. The artificial ice reduced the elevator and rudder control effectiveness by 12 percent and 8 percent respectively for the 0 deg flap setting. The longitudinal static stability was also decreased substantially (approximately 10 percent) because of the tail ice. Further discussion is provided to explain some of the effects of ice on the stability and control parameters.

Ratvasky, T. P.↗

NASA NTRS1993

Icing effects on aircraft stability and control determined from flight data - Preliminary results

The effects of airframe icing on the stability and control characteristics of the NASA DH-6 Twin Otter icing research aircraft were investigated by flight test. The flight program was developed to obtain stability and control parameters of the DH-6 in a baseline ('uniced') configuration and an 'artificially iced' configuration for specified thrust conditions. Stability and control parameter identification maneuvers were performed over a wide range of angles of attack for wing flaps retraced (0 deg) and wing flaps partially deflected (10 deg). Engine power was adjusted to hold thrust constant at one of three thrust coefficients (C(sub T) = 0.14, C(sub T) = 0.07, C(sub T) = 0.00). This paper presents only the pitching- and yawing-moment results from the flight test program. Stability and control parameters were estimated for the uniced and artificially iced configurations using a modified stepwise regression algorithm. Comparisons of the uniced and iced stability and control parameters are presented for the majority of the flight envelope. The artificial ice reduced the elevator and rudder control effectiveness by 12 percent and 8 percent respectively for the 0 deg flap setting. The longitudinal static stability was also decreased substantially (approximately 10 percent) because of the tail ice. Further discussion is provided to explain some of the effects of ice on the stability and control parameters.

Ratvasky, T. P.↗

NASA NTRS1921

Airplane Superchargers

Discussed here are the principles and operation of aircraft engine superchargers used to maintain and increase engine power as aircraft encounter decreases in the density of air as altitude rises. Details are given on the design and operation of the centrifugal compressors. A method is given for calculating the amount of power needed to drive a compressor. The effects of the use of a compressor on fuel system operation and design are discussed. Several specific superchargers that were in operation are described.

Noack, W G↗

NASA NTRS1923

Determination of climbing ability

The vertical distribution of the pressure, temperature, and density of the atmosphere varies from day to day. Thus, rates of climb on different days cannot be compared directly, but must be corrected with reference to a standard rate of diminution of air density with increasing altitude. The following problem, therefore, has to be solved. An airplane has climbed on a certain day under prevailing atmospheric conditions as shown by the barograph. How would the same airplane climb in a standard atmosphere? This problem has already been dealt with by Everling, using the monthly and yearly mean of the vertical temperature distribution. Von Mises solved the problem by arithmetical methods. Here, conditions are examined which shorten or lengthen the climbing time. In establishing the corrected barogram, computation seems more practical than graphical treatment. The basis of the answer to the question answered here is summed up in the remark that lift, drag, propeller thrust, and torque and engine power depend only on the density of the air and do not change with the pressure and temperature, provided that the density remains constant.

Blasius, H↗

NASA NTRS1937

Compression-ignition Engine Performance at Altitudes and at Various Air Pressures and Temperatures

Engine test results are presented for simulated altitude conditions. A displaced-piston combustion chamber on a 5- by 7-inch single cylinder compression-ignition engine operating at 2,000 r.p.m. was used. Inlet air temperature equivalent to standard altitudes up to 14,000 feet were obtained. Comparison between performance at altitude of the unsupercharged compression-ignition engine compared favorably with the carburetor engine. Analysis of the results for which the inlet air temperature, inlet air pressure, and inlet and exhaust pressure were varied indicates that engine performance cannot be reliably corrected on the basis of inlet air density or weight of air charge. Engine power increases with inlet air pressure and decreases with inlet air temperatures very nearly as straight line relations over a wide range of air-fuel ratios. Correction factors are given.

Moore, Charles S↗

NASA NTRS1946

Effect of the NACA Injection Impeller on the Mixture Distribution of a Double-row Radial Aircraft Engine

For the normal range of engine power the impeller provided marked improvement over the standard spray-bar injection system. Mixture distribution at cruising was excellent, maximum cylinder temperatures were reduced about 30 degrees F, and general temperature distribution was improved. The uniform mixture distribution restored the normal response of cylinder temperature to mixture enrichment and it reduced the possibility of carburetor icing, while no serious loss in supercharger pressure rise resulted from injection of fuel near the impeller outlet. The injection impeller also furnished a convenient means of adding water to the charge mixture for internal cooling.

Marble, Frank E.↗

NASA NTRS1953

Propeller-performance charts for transport airplanes

The preliminary selection of a propeller on the basis of cruising and take-off performance for application to transport airplanes at flight Mach numbers up to 0.8 can be accomplished by the use of charts and methods presented. The charts are of sufficient scope to permit a fairly rapid evaluation of the propeller performance for engine power ratings of 1,000 to 10,000 horsepower. The method is presented primarily in the interest of propeller-noise abatement.

Gilman, Jean, Jr↗

NASA NTRS1928

On the take-off of heavily loaded airplanes

This report examines the take-off conditions of airplanes equipped with tractive propellers, and particularly the more difficult take-off of airplanes heavily loaded per unit of wing area (wing loading) or per unit of engine power (power loading).

LOADS, TAKE-OFF↗

NASA NTRS1929

Airplane drag

It has been less well understood that the induced drag (or, better said, the undesired increase in the induced drag as compared with the theoretical minimum calculated by Prandtl) plays a decisive role in the process of taking off and therefore in the requisite engine power. This paper seeks to clarify the induced drag.

DRAG↗

NASA NTRS1924

Engine performance and the determination of absolute ceiling

This report contains a brief study of the variation of engine power with temperature and pressure. The variation of propeller efficiency in standard atmosphere is obtained from the general efficiency curve which is developed in NACA report no. 168. The variation of both power available and power required are then determined and curves plotted, so that the absolute ceiling may be read directly from any known sea-level value of the ratio of power available to power required.

Diehl, Walter S↗

NASA NTRS1937

Tests of a Wing-nacelle-Propeller Combination at Several Pitch Settings up to 42 Degrees

This report presents the results of tests of a 4-foot model of Navy propeller No. 4412 in conjunction with an NACA cowled nacelle mounted ahead of a thick wing in the 20-foot propeller-research tunnel. A range of propeller pitches from 17 degrees to 42 degrees at 0.75r was covered, and for this propeller the efficiency reached a maximum at a pitch setting of 27 degrees; at high pitches the efficiencies were slightly lower. The corrected propulsive efficiency is shown to be independent of the angle of attack for the high-speed and the climbing ranges of flight. A working chart is presented for the selection of similar propellers over a wide range of airplane speed, engine power, and propeller revolution.

Windler, Ray↗

NASA NTRS1943

Operating Temperatures of a Sodium-Cooled Exhaust Valve as Measured by a Thermocouple

Report presents the results of a thermocouple installed in the crown of a sodium-cooled exhaust valve. The valve was tested in an air-cooled engine cylinder and valve temperatures under various engine operating conditions were determined. A temperature of 1337 degrees F. was observed at a fuel-air ratio of 0.064, a brake mean effective pressure of 179 pounds per square inch, and an engine speed of 2000 r.p.m. Fuel-air ratio was found to have a large influence on valve temperature, but cooling-air pressure and variation in spark advance had little effect. An increase in engine power by change of speed or mean effective pressure increased the valve temperature. It was found that the temperature of the rear-spark-plug bushing was not a satisfactory indication of the temperature of the exhaust valve.

Sanders, J C↗

NASA NTRS1947

Effect of Modifications to Induction System on Altitude Performance of V-1710-93 Engine III : Use of Parabolic Rotating Guide Vanes and NACA Designed Auxiliary-stage Inlet Elbow and Interstage Duct

Bench runs of a modified V-1710-93 engine equipped with a two-stage supercharger, interstage carburetor, aftercooler assembly, and backfire screens have been made at a simulated altitude of 29,000 feet to determine the effect of several induction-system modifications on the engine and supercharger performance. The standard guide vanes on the auxiliary- and engine-stage superchargers were replaced by rotating guide vanes with a parabolic blade profile. The auxiliary-stage inlet elbow and interstage duct were replaced with new units of NACA design. These modifications were made one at a time and data were obtained after each change to determine the effect of each modification. All runs were made at a constant engine speed of 3000 rpm at a simulated altitude of 29,000 feet and all changes in engine power were made by varying the speed of the auxiliary-stage supercharger.

Standahar, Ray M↗

NASA NTRS1994

High-Temperature, Self-Lubricating Ceramic/Metal Composites

Four documents provide detailed information on ceramic/metal composite materials that are self-lubricating at temperatures as high as 900 degrees C. Materials used in bearings and seals for turbomachines, new energy-efficient automotive engines, power generators, pumps, and furnaces.

Sliney, Harold E.↗

NASA NTRS1966

Aeronautics and Space Report: Highlights 1966

The videotape includes footage of the following: space and aeronautic montage, Surveyor lands on the Moon, Lunar Orbiter, weather satellites, Orbiting Geophysical Observatory, Pagoes, Pioneer, sounding rockets, solar eclipse, X-15, lifting bodies, solid rockets, nuclear powered engines, Project Gemini ends, and Apollo-Saturn.

Source record↗

NASA NTRS1993

The line-emitting gas in active galaxies - A probe of the nuclear engine

This paper reviews some of the basic questions regarding the structure of the engine powering active galactic nuclei (AGN), the nature of the interaction between the AGN and the host galaxy, and the origin and evolution of AGN. The study of the dynamics and physical characteristics of the line-emitting gas in these objects has proven fruitful in addressing many of these issues. Recent advances in optical and infrared detector technology combined with the development of superior ground-based instruments have produced efficient new tools for the study of the line-emitting gas on nuclear and Galactic scales. Programs which take advantage of two of these new techniques, Fabry-Perot imaging spectroscopy and infrared spectroscopy, are described in this paper. The origin of nuclear activity in galaxies is also addressed in a third project which aims at determining the nature of luminous infrared galaxies.

Veilleux, Sylvain↗

NASA NTRS1959

Flight Investigation of an Automatic Throttle Control in Landing Approaches

A flight investigation of an automatic throttle control in landing approaches has been made. It was found that airspeed could be maintained satisfactorily by the automatic throttle control. Turbulent air caused undesirably large variations of engine power which were uncomfortable and disconcerting; nevertheless, the pilot felt that he could make approaches 5 knots slower with equal assurance when the automatic control was in operation.

Lina, Lindsay J.↗

NASA NTRS1998

Load Distribution in Transmissions "Split"

The transmission system of a helicopter must meet particularly critical requirements. It must transmit engine power to the rotor, at the same time ensuring a typical speed reduction of 60 to 1. It must also be safe, reliable, light, and reach a high level of performance while, at the same time, it must produce few vibrations and little noise. Helicopter transmissions have achieved high-level performances thanks to the combination of analyses, experiments, and the application of practical field experience. However, the new generation of helicopters will require transmission systems that are even safer, lighter, less noisy, and more reliable.

Krantz, Timothy L.↗