Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACTOR OPERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Establishing Isotopic Measurement Capabilities using Laser-Induced Breakdown Spectroscopy for the Molten Salt Reactor Campaign

Proof-of-principle H isotope ratios of aqueous aerosol systems and liquid droplets on filter paper have been measured using laser-induced breakdown spectroscopy (LIBS) with root mean square error of prediction values down to 1.9%. Molten salt reactors (MSRs) will consist of a complex chemical and radiological system consistently producing new fission products as the reactor operates. Some of these fission products and/or their daughter species will leave the salt in the reactor off-gas. Monitoring the composition of the off-gas, as well as the salt itself, is important for monitoring reactor performance, including burnup, corrosion, and the concentration of impurities. Tritium is of concern for MSRs because it will be produced from the irradiation of key salt constituents, including Li and Be. LIBS offers an avenue for in situ salt and off-gas monitoring by firing a laser onto or into the sample stream to generate a plasma. The plasma light can be monitored to measure an elemental fingerprint of the sample. Extending this analysis to include isotopic ratios offers a critical expansion of the in situ monitoring capabilities being developed. This study demonstrates the expansion of Oak Ridge National Laboratory’s LIBS capabilities to monitor isotopes and shows how simple calibrations may provide rapid semiquantitative models.

07 ISOTOPE AND RADIATION SOURCES↗

Immobilization of Cesium Traps from the BN-350 Fast Reactor (Aktau, Kazakhstan)

During BN-350 reactor operations and also during the initial stages of decommissioning, cesium traps were used to decontaminate the reactor’s primary sodium coolant. Two different types of carbon-based trap were used – the MAVR series, low ash granulated graphite adsorber (LAG) contained in a carrier designed to be inserted into the reactor core during shutdown; and a series of ex-reactor trap accumulators(TAs) which used reticulated vitreous carbon (RVC) to reduce Cs-137 levels in the sodium after final reactor shutdown. In total four MAVRs and seven TAs were used at BN-350 to remove an estimated cumulative 755 TBq of cesium. The traps, which also contain residual sodium, need to be immobilized in an appropriate way to allow them to be consigned as waste packages for long term storage and, ultimately, disposal. The present paper reports on the current status of the implementation phase, with particular reference to the work done to date on the trap accumulators, which have the most similarity with the cesium traps used at other reactors.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Transition core modeling for extended enrichment, accident tolerant fuel using PARCS/Polaris

Current plans and efforts from reactor operators and vendors to include extended enrichment (EE) and accident-tolerant fuel (ATF) in current reactor fleets motivate the study of these changes in reactor physics analysis. This work uses the US Nuclear Regulatory Commission core simulator PARCS to do the core calculation and SCALE Polaris lattice physics code to generate the required homogenized, few-group constants. The lattice model used is based on the GE-14 10x10 assemblies with UO{sub 2} fuels. Both nominal core and transition core are studied in this work, and both cores use GE-14 10x10 assemblies with UO{sub 2} fuel. The nominal core uses regular UO{sub 2} fuel with a maximum enrichment of 5 wt % and ZIRC-2 cladding. The ATF transition core uses FeCrAl cladding and regular UO{sub 2} fuel, while the EE-ATF transition core uses FeCrAl cladding with UO{sub 2} fuel with 8 max wt % enrichment. The accuracy presented in the colorset models verified the capability of the PARCS/Polaris procedures for the transition core analysis. For the whole core calculation, the ATF and EE-ATF transition core models were made in addition to the nominal core model. The core parameters to study are the core power distribution and power peaking factor, doppler temperature coefficients, and control rod worth at cold zero power and hot full power. Comparing the core parameters of the transition cores with the nominal core in PARCS, the results suggest that there is no unexpected outcome for the implementation of ATF and EE fuels. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Markov Decision Processes for Intelligent, Risk-Informed Asset-Management Decision-Making

Advanced nuclear reactors are a promising option for aiding the world in achieving its net-zero carbon emission goals, however, there are significant challenges to attaining and maintaining economic competitiveness with other sources of electricity. To improve the economic competitiveness of advanced reactor designs, a project was initiated to explore the use of Markov Decision Processes (MDPs) to guide asset-management decision-making during advanced reactor operation. MDPs are a powerful tool for optimizing decision-making in complex environments and their application to advanced reactors can aid in planning maintenance and repair activities to minimize downtime and maximize generation. The described approach expands on previous work regarding the use of MDPs for operational decision-making through the direct incorporation of real-time plant information. The integral MDP analysis includes information from online component diagnostic tools and the plant’s real-time generation risk assessment (GRA) and probabilistic risk assessment (PRA), which evaluate plant risk from both an economic and safety perspective. The result is an asset-management optimization framework that is based on real-time data regarding plant component status and the current best-estimate of plant risk. The paper presents an overview of the theoretical framework to incorporate the different information pathways into an integral MDP analysis, along with example analyses.

Grabaskas, David↗

AGC-2 Disassembly Report

The Next Generation Nuclear Plant (NGNP) Graphite Research and Development (R&D) Program is currently measuring irradiated material properties for predicting the behavior and operating performance of new nuclear graphite grades available for use within the cores of new very high temperature reactor designs. The Advanced Graphite Creep (AGC) experiment, consisting of six irradiation capsules, will generate irradiated graphite performance data for NGNP reactor operating conditions. The AGC experiment is designed to determine the changes to specific material properties such as thermal diffusivity, thermal expansion, elastic modulus, mechanical strength, irradiation induced dimensional change rate, and irradiation creep for a wide variety of nuclear grade graphite types over a range of high temperature, and moderate doses. A series of six capsules containing graphite test specimens will be used to expose graphite test samples to a dose range from 1 to 7 dpa at three different temperatures (600, 900, and 1200°C) as described in the Graphite Technology Development Plan. Since irradiation induced creep within graphite components is considered critical to determining the operational life of the graphite core, some of the samples will also be exposed to an applied load to determine the creep rate for each graphite type under both temperature and neutron flux. All six AGC capsules in the experiment will be irradiated in the Advanced Test Reactor (ATR). AGC-1 and AGC-2 will be irradiated in the south flux trap and AGC-3–AGC-6 will be irradiated in the east flux trap. The change in flux traps is due to NGNP irradiation priorities requiring the AGC experiment to be moved to accommodate Fuel irradiation experiments. After irradiation, all six AGC capsules will be cooled in the ATR Canal, sized for shipment, and shipped to the Materials and Fuels Complex (MFC) where the capsule will be disassembled in the Hot Fuel Examination Facility (HFEF). During disassembly, the metallic capsule will be machined open and the individual samples removed from the interior graphite body containing the samples. Samples removed from the capsule will be loaded in a shipping drum and shipped to the Idaho National Laboratory (INL) Research Center (IRC) for initial post-irradiation examination (PIE) and storage for any future testing at the newly completed Carbon Characterization Laboratory (CCL). All work was performed under an ASME NQA-1-2008;1a-2009 compliant quality assurance program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Study of effect of PWR cold leg temperature gradient on reactor core condition

Effects of temperature and flow gradients in Westinghouse designed three-loop Pressurized Water Reactor (PWR) cold legs, the piping between the main coolant pump and the reactor vessel, were evaluated using Computational Fluid Dynamics (CFD) code STAR CCM+ and coupled neutronic and thermal-hydraulic (T/H) code system VERA. In the parametric study, several symmetric and asymmetric temperature gradients that were significantly larger than those observed from plant measurements were applied to the cold leg inlets for comparison with the base case without any temperature gradient. A CFD model using the STAR-CCM+ code was developed for a portion of the RCS region between the Reactor Coolant Pump (RCP) and the core inlet based on previously validated modeling approach. The CFD simulation results were processed for the temperature and flow rate distributions at the core inlet as input to the VERA calculations. The VERA code system consists of COBRA-TF (CTF) for thermal-hydraulics, MPACT for reactor physics and neutron transport, and ORIGEN for isotopic depletion. The VERA model was for depletion calculations of a high-burnup loading pattern with the reactor core in pin-by-pin and subchannel resolution. The results of the study indicate that the postulated temperature gradients within the PWR cold legs do not result in any significant changes in the core inlet temperature distributions and the core power distributions during the reactor operation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Digial Technology Qualification Task 2 - Suitability of Digital Alternatives to Analog Sensors and Actuators

The next generation reactors in the U.S. are an opportunity for vendors to build new reactor technology with advanced Instrumentation and Control Systems (control rooms, DCS, etc.). The advances made in the development of many current generation operating reactors in other parts of the world are being used in the design and construction of new plants. These new plants are expected to have fully integrated digital control rooms, computerized procedures, integrated surveillance testing with on-line monitoring and a major effort toward improving the O&M and fault survivability of the overall systems. In addition the designs are also incorporating major improvements in the man-machine interface based on lessons learned in nuclear and other industries. The above relates primarily to the scope of supply in instrumentation and control systems addressed by Chapter 7 of the Standard Review Plan (SRP) NUREG-0800 (Reference 9.5), and the associated Balance of Plant (BOP) I&C systems. This does not relate directly to the actuator and motor, breaker, initiation circuitry, valve position, etc. which is the subject of this report and normally outside of the traditional Distributed Control System (DCS), for both safety and non-safety systems. The recommendations presented in this report will be used as input to I&C research programming for the implementation of lessons learned during the early phases of new build both for large light water reactors (LWR) and also small modular reactors (SMR). This report is intended to support current research plans and provide user (vendor, owner-operator) input to the optimization of these research plans.

99 GENERAL AND MISCELLANEOUS↗

Analysis of the pebble burnup profile in a pebble-bed nuclear reactor

It is known that in a pebble bed nuclear reactor, each fuel pebble draining through the core experiences a different amount of burnup depending on the precise trajectory that it follows. Understanding the burnup profile of pebbles is essential for reactor safety, as well as for fuel economy. Here, we introduce a method for constructing the burnup profile based on performing a discrete element simulation of the pebble drainage, followed by a burnup calculation in each individual pebble. This method is more accurate than previous approaches, and in particular it captures the extremal cases of pebble burnup. We demonstrate the method using the geometry, neutron flux data, and thermal characteristics from the HTR-10 reactor being developed at Tsinghua University. We examine pebble burnup during a single drainage cycle, and over multiple drainage cycles characteristic of normal reactor operation. Our results show that the presence of slow-moving boundary layers of pebbles near the reactor wall strongly influences the burnup profile. We perform a systematic study where the pebble–pebble and pebble–wall friction coefficients are independently varied, and we show that the strength of the boundary layers is a complex interplay of these two parameters.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Ceramic Coatings for Clad (The C 3 Project): Advanced Accident-Tolerant Ceramic Coatings for Zr-Alloy Cladding

The goal of this NEUP-IRP project is to develop a fuel concept based on an advanced ceramic coating for Zr-alloy cladding. The coated cladding must exhibit demonstrably improved performance compared to conventional Zr-alloy clad in the following respects: During normal service, the ceramic coating should decrease cladding oxidation and hydrogen pickup (the latter leads to hydriding and embrittlement). During a reactor transient (e.g., a loss of coolant accident), the ceramic coating must minimize or at least significantly delay oxidation of the Zr-alloy cladding, thus reducing the amount of hydrogen generated and the oxygen ingress into the cladding. The specific objectives of this project are as follows: To produce durable ceramic coatings on Zr-alloy clad using two possible routes: (i) MAX phase ceramic coatings or similar nitride or carbide coatings; and (ii) graded interface architecture (multilayer) ceramic coatings, using, for instance, an oxide such as yttria-stabilized zirconia (YSZ) as the outer protective layer. To characterize the structural and physical properties of the coated clad samples produced in 1. above, especially the corrosion properties under simulated normal and transient reactor operating conditions. To perform computational analyses to assess the effects of such coatings on fuel performance and reactor neutronics, and to perform fuel cycle analyses to assess the economic viability of modifying conventional Zr-alloy cladding with ceramic coatings. This project meets a number of the goals outlined in the NEUP-IRP call for proposals, including: Improve the fuel/cladding system through innovative designs (e.g. coatings/liners for zirconium-based cladding) Reduce or eliminate hydrogen generation Increase resistance to bulk steam oxidation Achievement of our goals and objectives, as defined above, will lead to safer light-water reactor (LWR) nuclear fuel assemblies, due to improved cladding properties and built-in accident resistance, as well as the possibilities for enhanced fuel/clad system performance and longevity.

36 MATERIALS SCIENCE↗

Postirradiation examination of HFIR-irradiated yttrium hydrides

The U.S. Department of Energy’s (DOE) Microreactor Program (MRP) is advancing key technologies to enable the deployment of truck-transportable, plug-and-play microreactors that operate at low power levels (< 20 MW th ), but at high temperatures (> 600 °C), while ensuring inherently safe reactor operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Numerical Simulation and Experimental Comparison of System Analysis Module 1D Mixing Model for Cold Shock Transients in the Gallium Thermal-Hydraulic Mixing Facility

Abstract Liquid metals are being investigated as coolants in many advanced reactor designs because of their high thermal conductivity and effectiveness at high temperatures. However, they often pose challenges to reactor operation and safety because of the complex thermal mixing and stratification in the plenum of pool-type reactor designs. The advanced system analysis code System Analysis Module (SAM) currently under development at Argonne National Laboratory aims to develop and implement thermal mixing models to accurately capture these complex thermal fluid behaviors. In this study, the SAM thermal mixing model was compared against experimental data from the Gallium Thermal-Hydraulic Experiment facility, a scaled liquid metal test facility that uses gallium as a surrogate fluid to investigate the stratification and thermal mixing of low-Prandtl-number fluids in the upper plenum of a liquid metal-cooled reactor. Two cold shock transient cases were used: one with stable stratified flow (Ri = 32) and one with stronger thermal mixing (Ri = 0.5). The resultant temperatures were then compared with the experimental temperatures over the entire plenum to assess the ability of the mixing models to capture the thermal behavior and to better correspond mixing parameters to various flow scenarios. Generally, the zero-dimensional mixing model was more capable of capturing the bulk temperature of the component modeled assuming that an accurate mass flow rate was provided, but it was inherently unable to capture thermal gradients in space. The one-dimensional mixing model was capable of capturing that the thermal gradients provided accurate selection of the mixing coefficients. Further, the temperature at the outlet junction was compared over time for each of the mixing models with the recorded experimental temperature. The implemented mixing models demonstrated the ability to effectively capture the overall thermal behavior for stronger mixing scenarios but struggled with more stably stratified flows. It was found that a system analysis code's covering of the entire range of different operating conditions still remains a challenging task, and it is suggested that further model and closure improvements are necessary to accurately capture complex thermal mixing and stratification phenomena.

stratification↗

The 2019 Edition of the IRPhEP Handbook

The International Reactor Physics Experiment Evaluation Project (IRPhEP) [1] was established to preserve and evaluate integral reactor physics experiment data, including separate or special effects measurements for nuclear energy and technology applications. Numerous international experiments have been performed over the past several decades to support reactor operations, safety, measurements, and design. Those experiments represent a significant investment of infrastructure, cost, and expertise that, in many instances, cannot be as easily reproduced. They represent valuable resources of data for present and future research, and provide the basis for recording, development, and validation of methods [2]. The primary focus of the IRPhEP is to provide an extensively peer-reviewed set of reactor physics integral data suitable for reactor designers and safety analysts to not just validate the analytical tools necessary to design next-generation nuclear reactors, but to establish the safety basis for their operation. Contributors worldwide collaborate to evaluate and review selected benchmark experiments for inclusion in the International Handbook of Evaluated Reactor Physics Benchmark Experiments (IRPhEP Handbook) [3]. More detailed discussion of the IRPhEP, including highlighted reactor physics benchmark evaluations, can be found in the November and December 2014 editions of Nuclear Science and Engineering [1]. Several new evaluations, and revisions to existing benchmarks have been prepared for inclusion in the 2019 edition of the IRPhEP Handbook (see Table I).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Coupling DAEM and CFD for simulating biomass fast pyrolysis in fluidized beds

We report results from computational simulations of an experimental, lab-scale bubbling bed biomass pyrolysis reactor that include a distributed activation energy model (DAEM) for the kinetics. In this study, we utilized multiphase computational fluid dynamics (CFD) to account for the turbulent hydrodynamics, and this was combined with the DAEM kinetics in a multi-component, multi-step reaction network. Our results indicate that it is possible to numerically integrate the coupled CFD–DAEM system without significantly increasing computational overhead. It is also clear, however, that reactor operating conditions, reaction kinetics, and multiphase flow dynamics all have major impacts on the pyrolysis products exiting the reactor. We find that, with the same pre-exponential factors and mean activation energies, inclusion of distributed activation energies in the kinetics can shift the predicted average value of the exit vapor-phase tar flux and its statistical distribution, compared to single-valued activation-energy kinetics. Perhaps the most interesting observed trend is that increasing the diversity of the DAEM activation energies appears to increase the mean tar yield, all else being equal. As a result, these findings imply that accurate resolution of the reaction activation energy distributions will be important for optimizing biomass pyrolysis processes.

09 BIOMASS FUELS↗

Accelerated materials evaluation for nuclear applications

This report addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors.

36 MATERIALS SCIENCE↗

Corrigendum to “Accelerated materials evaluation for nuclear applications” [J. Nucl. Mater. 488 (2017) 46–62]

The original article addresses the opportunities and complexities of using materials test reactors with high neutron fluxes to perform accelerated studies of material aging in power reactors operating at lower neutron fluxes and with different neutron flux spectra. Radiation damage and gas production in different reactors have been compared using the code, SPECTER. This code provides a common standard from which to compare neutron damage data generated by different research groups using a variety of reactors. This Corrigendum identifies a few typographical errors. Tables 2 and 3 are included in revised form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

POLCA8 - modelling of cross section variations inside hexagonal assemblies

This paper presents the POLCA8 approach for modelling non-constant cross section distributions inside hexagonal fuel assemblies. The multigroup diffusion equation is modified to account for intranodal cross section variations. The obtained equation is solved in a node-wise manner based on the Fourier expansion method. As a result of varying cross sections, the solution includes a particular part additionally to the homogeneous one. A method for obtaining the particular solution is derived. Numerical tests on a VVER-1000 core are presented showing the impact of cross-section variations to some key parameters for reactor operation. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

PTT System Performance Evaluation in 3-D Imaging of Calibrated Defects: Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials and Components

Research activity in this project is aimed at developing pulsed thermal tomography (PTT) architecture and algorithms for in-service non-destructive examination (NDE) of additively manufactured (AM) reactor components and materials. Recent advances in AM technology could allow cost-efficient fabrication of parts for operating reactors. However, because of stringent safety requirements, long-term performance of AM reactor components needs to be investigated before AM is widely accepted. Because of the complex shapes and significant surface roughness of components due to layer-by-layer welding process in AM, conventional methods might not be useful for in-service NDE of AM components. PTT is ideally suited for in-service NDE of AM metallic components because the method is non-contact, and offers high resolution #-D imaging of material flaws. The objective of this report is to provide initial evaluate of PTT performance sin detecting calibrated flaws in reactor structural materials. Preliminary COMSOL models were developed to conduct super computing simulations of PTT. In the experimental studies, high strength Stainless Steel 316 and Inconel 718 alloys were considered, as well as lower grade Stainless Steel 304, Nickel 200, and Hastelloy C276. Specimens investigated in this report consisted of approximately 1/4in-thick plates made out of these alloys using conventional manufacturing methods. The calibrated defects were created in the form of flat bottom holes (FBH) drilled in metallic plates. The diameters of FBH's varied from 1mm to 8mm, and their depths below the plate flat surface varied between 1mm and 6mm. The size of the smallest FBH was limited to 1mm because conventional mechanic drills were used for creating the holes. PTT imaging results have shown that 1mm-diameter FBH located 1mm and 2mm below the surface were detectable. Larger size FBH were detectable at greater depth. For example, 6mm-diameter FBH could be detected at 8mm depth. Image contrast varied slightly between the specimens, with the best reconstructions obtained in SS316 and C276 plates. In addition, a 2/3in-thick Inconel 718 nozzle plate produced with additive manufacturing method was imaged with PTT. It was shown that PTT can scan through the plate in approximately 20s. Several modes of 3-D data visualization were explored, including using ImageJ and MATLAB software packages.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Irradiation effects in Generation IV nuclear reactor materials

Generation IV reactor structural materials will be exposed to high doses and temperatures during reactor operation that may lead to irradiation-induced degradation. This degradation will differ from that seen in light water reactors and therefore understanding mechanisms controlling material performance during irradiation is critical for evaluating viability of Generation IV nuclear reactor concepts. This chapter discusses irradiation effects and microstructural changes that affect mechanical properties and dimensional stability of Generation IV reactor materials.

36 MATERIALS SCIENCE↗