SEARCH · Search NASA

Results for “Rotor Performance Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Comparison of a quasi-3D analysis and experimental performance for three compact radial turbines

An experimental aerodynamic evaluation of three compact radial turbine builds was performed. Two rotors which were 40-50 percent shorter in axial length than conventional state-of-the-art radial rotors were tested. A single nozzle design was used. One rotor was tested with the nozzle at two stagger angle settings. A second rotor was tested with the nozzle in only the closed down setting. Experimental results were compared to predicted results from a quasi-3D inviscid and boundary layer analysis, called MTSB (Meridl/Tsonic/Blayer). This analysis was used to predict turbine performance. It has previously been calibrated only for axial, not radial, turbomachinery. The predicted and measured efficiencies were compared at the design point for the three turbines. At the design points the analysis overpredicted the efficiency by less than 1.7 points. Comparisons were also made at off-design operating points. The results of these comparisons showed the importance of an accurate clearance model for efficiency predictions and also that there are deficiencies in the incidence loss model used.

Simonyi, P. S.↗

NASA NTRS1987

Comparing Test Data on Scale-Model Helicopter Rotors

Hovering data correlate well, but forward-flight data do not. Report compares acoustics and performance of small-scale helicopter rotor with those of full-scale rotor in both hovering and forward flight.

Kitaplioglu, Cahit↗

NASA NTRS1985

Aerodynamic performance of a 27-percent-scale AH-64 wind-tunnel model with baseline/advanced rotor blades

Performance of a 27-percent scale model of an advanced rotor designed for the AH-64 helicopter was measured in hover and at forward speeds of 50 to 130 knots. A baseline rotor, modeled after the current AH-64 rotor, was also tested to provide data for comparison. The investigation was conducted to validate procedures used at Langley to design rotors with increased performance potential and to provide a database for evaluation of current and future rotor systems. Both rotors were operated at full-scale tip speeds. Rotor thrust, forward speed, and ground height were varied for each rotor.

Kelley, H. L.↗

NASA NTRS1984

Hovering model helicopter rotor testing

A relatively large test chamber, chosen to minimize room interference effects during helicopter hovering rotor tests, was found in initial operations to exhibit large, random variations of thrust, torque, and blade flapping. The source of these problems, unsteady recirculation of test chamber flow, was addressed by the addition of a 'flow straightener' that reduced these parameter variations to 1.5 percent of mean values. Rotor performance was then measured outside the chamber in calm, free air conditions and compared with chamber results obtained before and after modifications. Attention is given to wake flow visualization conducted in the test chamber, as well as outside.

Piziali, R. A.↗

NASA NTRS1977

Wind tunnel investigation of rotor lift and propulsive force at high speed: Data analysis

The basic test data obtained during the lift-propulsive force limit wind tunnel test conducted on a scale model CH-47b rotor are analyzed. Included are the rotor control positions, blade loads and six components of rotor force and moment, corrected for hub tares. Performance and blade loads are presented as the rotor lift limit is approached at fixed levels of rotor propulsive force coefficients and rotor tip speeds. Performance and blade load trends are documented for fixed levels of rotor lift coefficient as propulsive force is increased to the maximum obtainable by the model rotor. Test data is also included that defines the effect of stall proximity on rotor control power. The basic test data plots are presented in volumes 2 and 3.

Mchugh, F.↗

NASA NTRS1989

A survey of nonuniform inflow models for rotorcraft flight dynamics and control applications

The results of a brief survey of nonuniform inflow models was summarized for the calculation of induced velocities at and near a lifting rotor in and out of ground effect. The survey, conducted from the perspective of flight dynamics and control applications, covers a spectrum of flight conditions including hover, vertical flight, and low-speed and high-speed forward flight, and reviews both static and dynamic aspects of the inflow. A primary emphasis is on the evaluation of various simple first harmonic inflow models developed over the years, in comparison with more sophisticated methods developed for use in performance and airload computations. The results of correlation with several sets of test data obtained at the rotor out of ground effect indicate that the Pitt/Peters first harmonic inflow model works well overall. For inflow near the rotor or in ground effect, it is suggested that charts similar to those of Heyson/Katzoff and Castles/De Leeuw of NACA be produced using modern free-wake methods for use in flight dynamic analyses and simulations.

Chen, Robert T. N.↗

NASA NTRS1990

A survey of nonuniform inflow models for rotorcraft flight dynamics and control applications

The results of a brief survey of nonuniform inflow models was summarized for the calculation of induced velocities at and near a lifting rotor in and out of ground effect. The survey, conducted from the perspective of flight dynamics and control applications, covers a spectrum of flight conditions including hover, vertical flight, and flow-speed and high-speed forward flight, and reviews both static and dynamic aspects of the inflow. A primary emphasis is on the evaluation of various simple first harmonic inflow models developed over the years, in comparison with more sophisticated methods developed for use in performance and airload computations. The results of correlation with several sets of test data obtained at the rotor out of ground effect indicate that the Pitt/Peters first harmonic inflow model works well overall. For inflow near the rotor or in ground effect, it is suggested that charts similar to those of Heyson/Katzoff and Castles/De Leeuw of NACA be produced using modern free-wake methods for use in flight dynamic analyses and simulations.

Chen, Robert T. N.↗

NASA NTRS1980

The effect of yaw on horizontal axis wind turbine loading and performance

The Mod-0 100 kW experimental wind turbine was tested to determine the effects of yaw on rotor power, blade loads and teeter response. The wind turbine was operated for extended periods at yaw angles up to 49 deg to define average or mean response to yaw. It was determined that the effect of yaw on rotor power can be approximated by the cube of the velocity normal to the rotor disc as long as the yaw angle is less than 30 deg. Blade bending loads were relatively unaffected by yaw, but teeter angle increased with wind speed as the magnitude of the yaw angle exceeded 30 deg indicating a potential for teeter stop impacts at large yaw angles. No other adverse effects due to yaw were noted during the tests.

Glasgow, J. C.↗

NASA NTRS2001

Efficient Low Noise Fan Overview and Preliminary Aerodynamic Design

With support from the Ultra-Efficient En,aine Technology (UEET) and Quiet Aircraft Technology (QAT) programs, an efficient low noise fan will be designed and tested to investigate aerodynamic and acoustic performance effects using trailing edge blowing (TEB). The fan uses TEB to fill the momentum deficit behind the fan rotor. This presentation will include an overview of the plan to design, build, and test the f a n in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel. In addition, the preliminary aerodynamic design will be presented.

Source record↗

NASA NTRS2017

Comprehensive Analysis Modeling of Small-Scale UAS Rotors

Multicopter unmanned aircraft systems (UAS), or drones, have continued their explosive growth in recent years. With this growth comes demand for increased performance as the limits of existing technologies are reached. In order to better design multicopter UAS aircraft, better performance prediction tools are needed. This paper presents the results of a study aimed at using the rotorcraft comprehensive analysis code CAMRAD II to model a multicopter UAS rotor in hover. Parametric studies were performed to determine the level of fidelity needed in the analysis code inputs to achieve results that match test data. Overall, the results show that CAMRAD II is well suited to model small-scale UAS rotors in hover. This paper presents the results of the parametric studies as well as recommendations for the application of comprehensive analysis codes to multicopter UAS rotors.

Analysis↗

NASA NTRS1983

Acoustic measurements of the X-wing rotor

Noise measurements of a stoppable X-wing rotor system model, tested in the Ames 40- by 80-foot wind tunnel, are summarized. Performance, control system stability, and noise of the model were investigated at various forward speeds, tip speeds, collective blade angles, jet blowing velocities, and model attack angles. The model was tested in the rotating wing helicopter configuration, in the fixed wing configuration, and in wing configurations between the two. Noise data obtained in the helicopter configuration at the two highest tip speeds (Mach 0.44 and 0.47) and at wind tunnel speeds below 140 knots are reported. Test configuration and performance information are included. General acoustic measurements (dB, dBA, and PNdB) at six microphone locations are presented for all conditions under which the background noise was below the model noise. More specific measurements (1/3-octave and blade passage frequency harmonic levels) are presented for selected conditions. Graphs of dBA and 1/3-octave spectra, which show the noise trends as functions of operating condition, are included. The noise depends mainly on the jet blowing velocity. The noise levels were highest at moderate jet blowing velocities, less at the highest velocity, and lowest with no blowing at all.

Mosher, M.↗

NASA NTRS2003

Spin Testing for Durability Began on a Self-Tuning Impact Damper for Turbomachinery Blades

NASA and Pratt & Whitney will collaborate under a Space Act Agreement to perform spin testing of the impact damper to verify damping effectiveness and durability. Pratt & Whitney will provide the turbine blade and damper hardware for the tests. NASA will provide the facility and perform the tests. Effectiveness and durability will be investigated during and after sustained sweeps of rotor speed through resonance. Tests of a platform wedge damper are also planned to compare its effectiveness with that of the impact damper. Results from baseline tests without dampers will be used to measure damping effectiveness. The self-tuning impact damper combines two damping methods-the tuned mass damper and the impact damper. It consists of a ball located within a cavity in the blade. This ball rolls back and forth on a spherical trough under centrifugal load (tuned mass damper) and can strike the walls of the cavity (impact damper). The ball s rolling natural frequency is proportional to the rotor speed and can be designed to follow an engine-order line (integer multiple of rotor speed). Aerodynamic forcing frequencies typically follow these engineorder lines, and a damper tuned to the engine order will most effectively reduce blade vibrations when the resonant frequency equals the engine-order forcing frequency. This damper has been tested in flat plates and turbine blades in the Dynamic Spin Facility. During testing, a pair of plates or blades rotates in vacuum. Excitation is provided by one of three methods--eddy-current engine-order excitation (ECE), electromechanical shakers, and magnetic bearing excitation. The eddy-current system consists of magnets located circumferentially around the rotor. As a blade passes a magnet, a force is imparted on the blade. The number of magnets used can be varied to change the desired engine order of the excitation. The magnets are remotely raised or lowered to change the magnitude of the force on the blades. The other two methods apply force to the rotating shaft itself at frequencies independent of the rotor speed. During testing, blade vibration is monitored with strain gauges and laser displacement probes.

Duffy, Kirsten↗

DOE OSTI2023

Development of dual phase soft magnetic laminate for advanced electric machines

The development of dual phase soft magnetic laminate for advanced electric machines at General Electric is summarized, including alloy development, properties, manufacturing trials, prototype experience, potential applications, and future material development. Dual phase soft magnetic laminates provide the flexibility to tune magnetic/non-magnetic state at the desired locations, using solution nitriding treatment with protective mask/coating. This enabling material technology benefits electric machine performance by reducing flux leakage in the laminates. It also decouples the electromagnetic and mechanical design, which opens up the design space for advanced electric machines. Magnetic and mechanical properties of dual phase laminates were compared to commercial FeSi and FeCo soft magnetic laminates. Driven by the market needs for high power density and high-speed electric machines, a synchronous reluctance (SynRel) machine without PMs using dual phase soft magnetic laminates was assessed in machine electromagnetic performance as well as rotor stress analysis by finite element simulation. Successful prototype build and testing further retired manufacturing risks and advanced the technology maturity level. Future material development with higher mechanical strength, higher saturation magnetization, higher permeability, and lower loss are highly desired for ground and air transportation electrification.

Rallabandi, Vandana↗

NASA NTRS1973

Design and experimental results for a turbine with jet flap stator and jet flap

The overall performance and detailed stator performance of a negative hub reaction turbine design featuring a moderately low solidity jet flap stator and a jet flap rotor were determined. Testing was conducted over a range of turbine expansion ratios at design speed. At each expansion ratio, the stator jet flow and rotor jet flow ranged up to about 7 and 8 percent, respectively, of the turbine inlet flow. The performance of the jet flap stator/jet flap rotor turbine was compared with that of a turbine which used the same jet flap rotor and a conventional, high solidity plan stator. The effect on performance of increased axial spacing between the jet stator and rotor was also investigated.

Bettner, J. L.↗

NASA NTRS1984

Growian rotor blades: Production development, construction and test

Development and construction of three 50 m rotor blades for a 3 MW wind turbine are described. A hybrid concept was chosen, i.e., a load carrying inflexible steel spar and a glass fiber reinforced plastic skin. A test blade was constructed and static loading tests, dynamic vibration tests and fatigue tests on critical welds as well as at the connection between spar and blade skin were performed. All test results show good accordance with calculated values, and were taken into consideration during the construction of two rotor blades.

Thiele, H. M.↗

NASA NTRS2020

Model Rotor Hover Performance at Low Reynolds Number

Hover performance data from four key experiments has been analyzed in detail to shed some light on model rotor hover performance at low Reynolds number. Each experiment used the simplest blade geometry. The blades were constant chord and untwisted. Three experiments used blades with the NACA 0012 airfoil from root to tip. The NACA 0015 was used in the earliest test. The four experiments provide data spanning a Reynolds number range of 136,500 to 548,700. The specific objective of this report is to ask and answer two questions: 1. Does blade aspect ratio influence hover performance or is rotor solidity the fundamental rotor geometry parameter for practical engineering purposes? ANSWER: Rotor solidity is the fundamental rotor geometry parameter for practical engineering purposes. Any effect of blade aspect ratio appears to be such a secondary variable that its effect lies within the range of experimental error. 2. Is Reynolds number a significant factor in scaling up hover performance to full-scale rotor performance? The answer is twofold. ANSWER: (a) Reynolds number effects on the increase of power with thrust do not appear to be a significant factor for practical engineering purposes, and (b) Reynolds number effects on minimum profile power at or very near zero rotor thrust could not be clearly established primarily because the low torque levels could not be accurately measured with the test equipment used. This has led to significant data scatter. A number of other observations can be made based on the analysis provided herein. For instance: 1. The test matrices used in the four key references contained far too few data points. A collective pitch variation of four or five data points is insufficient to establish experimental accuracy and data repeatability. 2. A common property of the power-versus-thrust (raised to the 3/2 exponent) graphs was that this curve was linear below the onset of blade stall. 3. The blade-to-blade interference at or near zero thrust may, in fact, be creating a turbulent flow field such that the effective Reynolds number at a blade element is considerably greater than what theories using two-dimensional (2D) airfoil properties at a blade element would calculate. 4. Definitive experiments answering the two key questions have yet to be made.

Model Rotor Hover Performance↗

NASA NTRS2012

Performance and Loads Correlation of a UH-60A Slowed Rotor at High Advance Ratios

Measured data from the slowed rotor part of the 2010 UH-60A Airloads Rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. The emphasis in this initial study is to correlate overall trends. This analytical effort considers advance ratios from 0.3 to 1.0, with the rotor rotational speed at 40%NR. The rotor performance parameters considered are the thrust coefficient, power coefficient, L/DE, torque, and H-force. The blade loads considered are the half peak-to-peak, mid-span and outboard torsion, flatwise, and chordwise moments, and the pitch link load. For advance ratios . 0.7, the overall trends for the performance and loads (excluding the pitch link load) could be captured, but with substantial overprediction or underprediction. The correlation gradually deteriorates as the advance ratio is increased and for advance ratios . 0.8 there is no correlation. The pitch link load correlation is not good. There is considerable scope for improvement in the prediction of the blade loads. Considering the modeling complexity associated with the unconventional operating condition under consideration, the current predictive ability to capture overall trends is encouraging.

Kottapalli, Sesi B.↗

NASA NTRS1980

A comprehensive analytical model of rotorcraft aerodynamics and dynamics. Part 1: Analysis development

Structural, inertia, and aerodynamic models were combined to form a comprehensive model of rotor aerodynamics and dynamics that is applicable to a wide range of problems and a wide class of vehicles. A digital computer program is used to calculate rotor performance, loads, and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. The analysis is intended for use in the design, testing, and evaluation of rotors and rotorcraft, and to be a basis for further development of rotary wing theories.

Johnson, W.↗