Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separate Effect Test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Hydrogen leak detection in the Space Shuttle

This study focuses on a helium gas jet flowing into room air. Measurements of helium concentration and velocity in the jet-air mixture are reported. The objective is to learn about jet characteristics so that dynamically similar hydrogen leaks may be located in the Space Shuttle. The hazardous gas detection system (HGDS) in the mobile launch pad uses mass spectrometers to monitor the shuttle environment for leaks. The mass spectrometers are fed by long sample tubes which draw gas from the payload bay, mid body, aft engine compartment and external tank. The overall purpose of this study is to improve the HGDS especially in its potential for locating hydrogen leaks. A rapid-response leak detection experiment was designed, built, and tested, following on the work done in this program last summer. The apparatus included a Perkin Elmer MGA-1200 mass spectrometer and air velocity transducer, both monitored by a Macintosh IIFX computer using LabVIEW software. A jet of helium flowing into the lab air simulated a gas leak. Steady helium or hydrogen-nitrogen jets were logged for concentration and velocity, and the power spectral density of each was computed. Last year, large eddies and vortices were visually seen with Schlieren imaging, and they were detected in the time plots of the various instruments. The response time of the MGA-1200 was found in the range of 0.05 to 0.1 sec. Pulsed concentration waves were clearly detected at 25 cycles per sec by spectral analysis of MGA data. No peaks were detected in the power spectrum, so in the present study, 10 Hz bandwidth-averaged power levels were examined at regular frequency intervals. The practical consequences of last year's study are as follows: sampling frequency should be increased above the present rate of 1 sample per second so that transients could be observed and analyzed with frequency response methods. Many more experiments and conditions were observed in this second summer, including the effects of orifice diameter, jet velocity, sample tube design, radial effects, vertical flow, and low hydrogen concentrations (1 percent). A frequent observation was that the power spectrum, calculated from the Fourier transform of concentration fluctuations, gives a separate piece of information from concentration. Many of the tests suggest that power is high where mixing occurs at the helium-air interface. This fact is apparently independent of the concentration level, which could be high or low, but depends on the sample location relative to the jet (leak) origin, whereas high concentration may be due to a strong leak far away or a small leak close to the sample tube. If the power is low for any concentration level, this would signify helium is arriving at the sample tube by diffusion, not chaotic mixing caused by the jet interaction with air. The practical result is to propose a modification of the HGDL mass spectrometer data sampling and software so that sampling rates could be capable of observing at least 25 Hz fluctuations.

Barile, Ronald G↗
NASA NTRS1997

Cluster Observations for Combined X-Ray and Sunyaev-Zel'dovich Estimates of Peculiar Velocities and Distances

Measurements of the peculiar velocities of galaxy clusters with respect to the Hubble flow allow the determination of the gravitational field from all matter in the universe, not just the visible component. The Sunyaev-Zel'dovich (SZ) effect (the inverse-Compton scattering of cosmic microwave background photons by the hot gas in clusters of galaxies) allows these velocities to be measured without the use of empirical distance indicators. Additionally, because the magnitude of the SZ effect is independent of redshift, the technique can be used to measure velocities out to the epoch of cluster formation. The SZ technique requires a determination of the temperature of the hot cluster gas from X-ray observations, and measurements of the SZ effect at millimeter wavelengths to separate the contribution from the thermal motions within the gas from that of the cluster peculiax velocity. We have constructed a bolometric receiver, the Sunyaev-Zel'dovich Infrared Experiment, specifically to make measurements of the SZ effect at millimeter wavelengths in order to apply the SZ technique to peculiar velocity measurements. This receiver has already been used to set limits to the peculiar velocities of two galaxy clusters at z approx. 0.2. As a test of the SZ technique, the double cluster pair Abell 222 and 223 was selected for observation. Measurements of the redshifts of the two components suggest that, if the clusters are gravitationally bound, they should exhibit a relative velocity of 10OO km/ s, well above the expected precision of 200 km/ s (set by astrophysical confusion) that is expected from the SZ method. The temperature can be measured from ASCA data which we obtained for this cluster pair. However, in order to ensure that the temperature estimate from the ASCA data was not dominated by cooling flows within the cluster, we requested ROSAT HRI observations of this cluster pair. Analysis of the X-ray properties of the cluster pair is continuing by combining the ROSAT observations funded under this proposal, archival PSPC data and our own PI ASCA data. The imaging data shows that neither cluster has a strong cooling flow, although A223 is the more compact of the two components. A223 also has a sub-cluster projected 1 Mpc to the North. The observed properties of this cluster pair are strikingly similar to those of the well-studied pair of A399 and A401 which are widely believed to be interacting and are in the initial stages of merging. This strengthens our selection of this cluster pair as a test for cluster peculiar motions. Combining these X-ray observations with SUZIE measurements of the SZ effect will provide important constraints on cluster merger models. This part of the program has been heavily delayed by bad weather at Mauna Kea, however SZ observations were obtained in November 1997 as part of a separately funded effort. These data are currently being analyzed.

Lange, A. E.↗
NASA NTRS1975

Centaur Standard Shroud (CSS) Heated Altitude Jettison Tests

Altitude jettison tests, at a pressure of 20 torr (0.39 psia), were performed on the Centaur Standard Shroud (CSS) in a 100-foot diameter vacuum chamber. These jettison tests were part of a series of flight qualification tests which were performed on the new CSS system in preparation for the Helios and Viking missions. The first two tests subjected the CSS to a thermal cycle which simulated aerodynamic heating during ascent flight and the third test was performed at altitude pressure and in ambient temperature conditions. The purpose of the ambient temperature test was to provide base line data by which the separate machanical and thermal factors that influence jettison performance could be evaluated individually. The CSS was successfully jettisoned in each of the three tests. Also, thermal, stress, and structural deflection data were obtained which verified the analytical predictions of CSS response to flight environmental conditions and performance during jettison. In addition, much important information was obtained on critical CSS-to-payload clearance losses due to shell motions prior to and during jettison. The effectiveness of the separation system was successfully demonstrated at maximum flight temperatures.

Source record↗
NASA NTRS1985

A study of the second and third order closure models of turbulence for prediction of separated shear flows

The hybrid model of the Reynolds-stress turbulence closure is tested for the computation of the flows over a step and disk. Here it is attempted to improve the redistributive action of the turbulence energy among the Reynolds stresses. By evaluating the existing models for the pressure-strain correlation, better coefficients are obtained for the prediction of separating shear flows. Furthermore, the diffusion rate of the Reynolds stresses is reevaluated adopting several algebraic correlations for the triple-velocity products. The models of Cormack et al., Daly-Harlow, Hanjalic-Launder, and Shir were tested for the reattaching shear flows. It was generally observed that all these algebraic models give considerably low values of the triple-velocity products. This is attributed to the fact that none of the algebraic models can take the convective effect of the triple-velocity products into account in the separating shear flows, thus resulting in much lower diffusion rate than Reynolds stresses. In order to improve the evaluation of these quantities correction factors are introduced based on the comparison with some experimental data.

Amano, R. S.↗
NASA NTRS1976

Results of test MA22 in the NASA/LaRC 31-inch CFHT on an 0.010-scale model (32-0) of the space shuttle configuration 3 to determine RCS jet flow field interaction, volume 1

A wind tunnel test was conducted in the Langley Research Center 31-inch Continuous Flow Hypersonic Wind Tunnel from May 6, 1975 through June 3, 1975. The primary objectives of this test were the following: (1) to study the ability of the wind tunnel to repeat, on a run-to-run basis, data taken for identical configurations to determine if errors in repeatability could have a significant effect on jet interaction data, (2) to determine the effect of aerodynamic heating of the scale model on jet interaction, (3) to investigate the effects of elevon and body flap deflections on jet interaction, (4) to determine if the effects from jets fired separately along different axes can be added to equal the effects of the jets fired simultaneously (super position effects), (5) to study multiple jet effects, and (6) to investigate area ratio effects, i.e., the effect on jet interaction measurements of using wind tunnel nozzles with different area ratios in the same location. The model used in the test was a .010-scale model of the Space Shuttle Orbiter Configuration 3. The test was conducted at Mach 10.3 and a dynamic pressure of 150 psf. RCS chamber pressure was varied to simulate free flight dynamic pressures of 5, 7.5, 10, and 20 psf.

Kanipe, D. B.↗
NASA NTRS1995

Sailplane Glide Performance and Control Using Fixed and Articulating Winglets

An experimental study was conducted to investigate the effects of controllable articulating winglets on glide performance and yawing moments of high performance sailplanes. Testing was conducted in the Texas A&M University 7 x 10 foot Low Speed Wind Tunnel using a full-scale model of the outboard 5.6 feet of a 15 meter class high performance sailplane wing. Different wing tip configurations could be easily mounted to the wing model. A winglet was designed in which the cant and toe angles as well as a rudder on the winglet could be adjusted to a range of positions. Cant angles used in the investigation consisted of 5, 25, and 40 degrees measured from the vertical axis. Toe-out angles ranged from 0 to 22.5 degrees. A rudder on the winglet was used to study the effects of changing the camber of the winglet airfoil on wing performance and wing yawing moments. Rudder deflections consisted of-10, 0, and 10 degrees. Test results for a fixed geometry winglet and a standard wing tip are presented to show the general behavior of winglets on sailplane wings, and the effects of boundary-layer turbulators on the winglets are also presented. By tripping the laminar boundary-layer to turbulent before laminar separation occurs, the wing performance was increased at low Reynolds numbers. The effects on the lift and drag, yawing moment, pitching moment, and wing root bending moment of the model are presented. Oil flows were used on the wing model with the fixed geometry winglet and the standard wing tip to visualize flow directions and areas of boundary layer transition. A cant angle of 25 degrees and a toe-out angle of 2.5 degrees provided an optimal increase in wing performance for the cant and toe angles tested. Maximum performance was obtained when the winglet rudder remained in the neutral position of zero degrees. By varying the cant, toe, and rudder angles from their optimized positions, wing performance decreases. Although the winglet rudder proved to be more effective in increasing the yawing moment compared to varying the cant and toe angles, the amount of increased yawing moment was insignificant when compared to that produced by the vertical tail. A rudder on the winglet was determined to be ineffective for providing additional yaw control.

Colling, James David↗
NASA NTRS1971

Large silver-cadmium technology program

The effects of varying cell design on operation factors on the electrochemical performance of sealed, silver-cadmium cells were determined. A factorial experiment was conducted for all test cells constructed with organic separators. Three operating factors were evaluated: temperature, depth of discharge, and charge rate. The six construction factors considered were separator, absorber, electrolyte quantity, cadmium electrode type, cadmium-to-silver ratio, and auxiliary electrode. Test cells of 4 ampere-hour capacity were fabricated and cycled. The best performing cells, on a 94 minute orbit, at 40% depth of discharge, were those containing silver-treated fibrous sausage casings as the separator, and Teflon-ated, pressed cadmium electrodes. Cycling data of cells with inorganic separators (Astroset) are given. Best performance was shown by cells with nonwoven nylon absorbers. Rigid inorganic separators provided the best barrier to silver migration.

Charlip, S.↗
NASA NTRS1975

Abort separation study of a shuttle orbiter and external tank at hypersonic speeds

The effects of several parameters on the relative motions of a space shuttle orbiter design and its external tank were determined during staging for the return-to-launch-site abort mode. The parameters included angle of attack, dynamic pressure, flight-path angle, pitch rate, elevon effectiveness and the use of thrust applied to the tank. The relative positions of each component were determined by a separation trajectory computer program which incorporated data obtained in wind-tunnel tests with the orbiter and tank in proximity. These tests were conducted at Mach 10.3 in a continuous-flow hypersonic tunnel. All separation cases were initiated at a constant Mach number of 10 with an assumed sideslip angle of 0 deg.

Bernot, P. T.↗
NASA NTRS1988

The topology of large-scale structure. II - Nonlinear evolution of Gaussian models

The evolution of non-Gaussian behavior in the large-scale universe from Gaussian initial conditions is studied. Topology measures developed in previous papers are applied to the smoothed initial, final, and biased matter distributions of cold dark matter, white noise, and massive neutrino simulations. When the smoothing length is approximately twice the mass correlation length or larger, the evolved models look like the initial conditions, suggesting that random phase hypotheses in cosmology can be tested with adequate data sets. When a smaller smoothing length is used, nonlinear effects are recovered, so nonlinear effects on topology can be detected in redshift surveys after smoothing at the mean intergalaxy separation. Hot dark matter models develop manifestly non-Gaussian behavior attributable to phase correlations, with a topology reminiscent of bubble or sheet distributions. Cold dark matter models remain Gaussian, and biasing does not disguise this.

Melott, Adrian L.↗
NASA NTRS2003

Pilot Interactions in an Over-Constrained Conflict Scenario as Studied in a Piloted Simulation of Autonomous Aircraft Operations

Feasibility and safety of autonomous aircraft operations were studied in a multi-piloted simulation of overconstrained traffic conflicts to determine the need for, and utility of, priority flight rules to maintain safety in this extraordinary and potentially hazardous situation. An overconstrained traffic conflict is one in which the separation assurance objective is incompatible with other objectives. In addition, a proposed scheme for implementing priority flight rules by staggering the alerting time between the two aircraft in conflict was tested for effectiveness. The feasibility study was conducted through a simulation in the Air Traffic Operations Laboratory at the NASA Langley Research Center. This research activity is a continuation of the Distributed Air-Ground Traffic Management feasibility analysis reported in the 4th USA/Europe Air Traffic Management R&D Seminar in December 2001 (paper #48). The over-constrained conflict scenario studied here consisted of two piloted aircraft that were assigned an identical en-route waypoint arrival time and altitude crossing restriction. The simulation results indicated that the pilots safely resolved the conflict without the need for a priority flight rule system. Occurrences of unnecessary maneuvering near the common waypoint were traced to false conflict alerts, generated as the result of including waypoint constraint information in the broadcast data link message issued from each aircraft. This result suggests that, in the conservative interests of safety, broadcast intent information should be based on the commanded trajectory and not on the Flight Management System flight plan, to which the aircraft may not actually adhere. The use of priority flight rules had no effect on the percentage of the aircraft population meeting completely predictable which aircraft in a given pair would meet the constraints and which aircraft would make the first maneuver to yield right-of-way. Therefore, the proposed scheme for implementing priority flight rules through staggering the alerting time between the two aircraft was completely effective. The data and observations from this experiment, together with results from the previously reported study, support the feasibility of autonomous aircraft operations.

Wing, David J.↗
NASA NTRS2004

Fourth Computational Aeroacoustics (CAA) Workshop on Benchmark Problems

This publication contains the proceedings of the Fourth Computational Aeroacoustics (CAA) Workshop on Benchmark Problems. In this workshop, as in previous workshops, the problems were devised to gauge the technological advancement of computational techniques to calculate all aspects of sound generation and propagation in air directly from the fundamental governing equations. A variety of benchmark problems have been previously solved ranging from simple geometries with idealized acoustic conditions to test the accuracy and effectiveness of computational algorithms and numerical boundary conditions; to sound radiation from a duct; to gust interaction with a cascade of airfoils; to the sound generated by a separating, turbulent viscous flow. By solving these and similar problems, workshop participants have shown the technical progress from the basic challenges to accurate CAA calculations to the solution of CAA problems of increasing complexity and difficulty. The fourth CAA workshop emphasized the application of CAA methods to the solution of realistic problems. The workshop was held at the Ohio Aerospace Institute in Cleveland, Ohio, on October 20 to 22, 2003. At that time, workshop participants presented their solutions to problems in one or more of five categories. Their solutions are presented in this proceedings along with the comparisons of their solutions to the benchmark solutions or experimental data. The five categories for the benchmark problems were as follows: Category 1:Basic Methods. The numerical computation of sound is affected by, among other issues, the choice of grid used and by the boundary conditions. Category 2:Complex Geometry. The ability to compute the sound in the presence of complex geometric surfaces is important in practical applications of CAA. Category 3:Sound Generation by Interacting With a Gust. The practical application of CAA for computing noise generated by turbomachinery involves the modeling of the noise source mechanism as a vortical gust interacting with an airfoil. Category 4:Sound Transmission and Radiation. Category 5:Sound Generation in Viscous Problems. Sound is generated under certain conditions by a viscous flow as the flow passes an object or a cavity.

Dahl, Milo D.↗
NASA NTRS2018

A Numerical and Experimental Investigation of Flow Separation Control over a Wall-Mounted Hump Model

Numerical simulations and wind tunnel experiments were performed to investigate flow separation and its control over a wall-mounted hump model. Three-dimensional, unsteady fluid dynamic simulations were used to capture the relevant flow physics of unsteady flow separation and its control via active and passive flow control methods. Surface pressure measurements and surface oilflow visualization were obtained in the experiments. Current measurements documented a considerably thinner incoming boundary layer, but similar pressure distribution, compared to the reference data reported in the CFD (Computational Fluid Dynamics) Validation (CFDVAL 2004) Experiments. Consistent with the data available in the literature, numerical simulations predicted a longer separation bubble, which manifested itself as a shift in the pressure distributions. Streamwise vortices generated by passive vortex generators increased the suction pressure and provided substantial pressure recovery. Numerical simulations of vortex generators qualitatively predicted the effects of control, and revealed patterns of attached/separated flow regions. On the other hand, active flow control using steady discrete jets reduced, but was not able to eliminate, flow separation for the tested configuration. Although the major disagreement between the numerical and experimental results was in the pressure recovery region due to the inaccurate prediction of separation bubbles, the relative pressure recoveries from the baselines were comparable. Surface oilflow visualization and simulated surface streamlines were qualitatively in good agreement revealing the key flow features.

Koklu, Mehti↗
NASA NTRSDate not supplied

Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission

Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. Had it succeeded, one of the mission goals was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.

solar sail↗
NASA NTRSDate not supplied

Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission

Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. One of the goals of the mission was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.

solar sail↗
NASA NTRS1947

Effect of Various Methods of Boundary-Layer Control on Performance of V-1710-93 Engine-Stage Supercharger

Four methods of boundary-layer control were tried during an investigation to improve the flow in the impeller passages of a V-1710-93 engine-stage supercharger. The boundary layer along the impeller front shroud was removed by suction. In one method the removal was accomplished by recirculation of the air to the impeller inlet; in another method, by external removal. In the other methods, slots were cut through the impeller-blade faces first at 30 percent and then at 30 and 70 percent of the mean-flow-path length measured from leading edges of the rotating inlet guide vanes to introduce air from the high-pressure side of the blades into the region where stagnation and separation were suspected. A slight improvement in performance was obtained when the boundary layer was removed through the impeller front shroud. In general, this improvement become more pronounced as the amount of air removed was increased even though the excessive impeller frontal clearance maintained for these tests, together with an exaggerated negative pressure gradient, apparently induced flow separation on the diffuser front and rear walls as well as on the impeller front shroud. The use of slots in the impellers at the locations selected had a detrimental effect on the supercharger performance characteristics.

Kohl, Robert C.↗
NASA NTRS1999

Wind-Tunnel Overpressure Signatures From a Low-Boom HSCT Concept With Aft-Fuselage-Mounted Engines

A 1:300 scale wind-tunnel model of a conceptual High-Speed Civil Transport (HSCT) designed to generate a shaped, low-boom pressure signature on the ground was tested to obtain sonic-boom pressure signatures in the Langley Research Center Unitary Plan Wind Tunnel at a Mach number of 1.8 and a separation distance of about two body lengths or four wing-spans from the model. Two sets of engine nacelles representing two levels of engine technology were used on the model to determine the effects of increased nacelle volume. Pressure signatures were measured for (model lift)/(design lift) ratios of 0.5, 0.63, 0.75, and 1.0 so that the effect of lift on the pressure signature could be determined. The results of these tests were analyzed and used to discuss the agreement between experimental data and design expectations.

Mack, Robert J.↗
NASA NTRS2006

Small Hot Jet Acoustic Rig Validation

The Small Hot Jet Acoustic Rig (SHJAR), located in the Aeroacoustic Propulsion Laboratory (AAPL) at the NASA Glenn Research Center in Cleveland, Ohio, was commissioned in 2001 to test jet noise reduction concepts at low technology readiness levels (TRL 1-3) and develop advanced measurement techniques. The first series of tests on the SHJAR were designed to prove its capabilities and establish the quality of the jet noise data produced. Towards this goal, a methodology was employed dividing all noise sources into three categories: background noise, jet noise, and rig noise. Background noise was directly measured. Jet noise and rig noise were separated by using the distance and velocity scaling properties of jet noise. Effectively, any noise source that did not follow these rules of jet noise was labeled as rig noise. This method led to the identification of a high frequency noise source related to the Reynolds number. Experiments using boundary layer treatment and hot wire probes documented this noise source and its removal, allowing clean testing of low Reynolds number jets. Other tests performed characterized the amplitude and frequency of the valve noise, confirmed the location of the acoustic far field, and documented the background noise levels under several conditions. Finally, a full set of baseline data was acquired. This paper contains the methodology and test results used to verify the quality of the SHJAR rig.

Brown, Cliff↗
NASA NTRS1999

Effects of Fiber/Matrix Interface and its Composition on Mechanical Properties of Hi-Nicalon/Celsian Composites

To evaluate the effects of fiber coatings on composite mechanical properties. unidirectional celsian matrix composites reinforced with uncoated Hi-Nicalon fibers and those precoated with a dual BN/SiC layer in two separate batches (batch 1 and batch 2) were tested in three-point flexure. The uncoated-fiber reinforced composites showed catastrophic failure with strength of 210+/-35 MPa and a flat fracture surface. In contrast, composites reinforced with coated fibers exhibited graceful failure with extensive fiber pullout and showed significantly higher ultimate strengths, 904 and 759 MPa for the batch 1 and 2 coatings. respectively. Fiber push-in tests and microscopic examination indicated no chemical reaction at the uncoated or coated fiber-matrix interfaces that might be responsible for fiber strength degradation. Instead, the low strength of composite with uncoated fibers was due to degradation of the fiber strength from mechanical damage during composite processing. Despite identical processing, the first matrix cracking stresses (Sigma(sub mc)) of the composites reinforced with fibers coated in batch 1 and batch 2 were quite different, 436 and 122 MPa, respectively. The large difference in Sigma(sub mc) of the coated-fiber composites was attributed to differences in fiber sliding stresses (Tau(sub friction)), 121.2+/-48.7 and 10.4+/-3.1 MPa, respectively. for the two composites as determined by the fiber push-in method. Such a large difference in Tau(sub friction). for the two composites was found to be due to the difference in the compositions of the interface coatings. Scanning Auger microprobe analysis revealed the presence of carbon layers between the fiber and BN. and also between the BN and SiC coatings in the composite showing lower Tau(sub friction). This resulted in lower Sigma(sub mc) in agreement with the ACK theory. The ultimate strengths of the two composites depended mainly on the fiber volume fraction and were not significantly effected by Tau(sub friction) values, as expected. The poor reproducibility of the fiber coating composition between the two batches was judged to be the primary source of the large differences in performance of the two composites.

Bansal, Narottam P.↗