Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Continuous analysis of stresses from arbitrary surface loads on a half space

A new form of elemental surface load on a half space is introduced, presuming a quasi-pyramidal variation of load which is doubly linear in each of four rectangular parts of a surface rectangle. Approximations of arbitrary load distributions by sums of such elements are continuous, piecewise linear in two directions and well adaptable. The loads may be normal or tangential. The explicit solutions obtained for all stress and displacement components due to each elemental load involve only elementary functions, are free of the discontinuities which arise with stepwise elements, and are suitable for computing. Some illustrative stress distributions are presented for elemental loads and for multiple pyramidal loads involving both normal and tangential loads. The value of the load continuity in the more complicated analyses of surface cracks is also illustrated.

Bell, J. C.↗
NASA NTRS1984

High temperature stress-strain analysis

The objectives are threefold: to assist in developing predictive tools needed to improve design analyses and procedures for the efficient and accurate prediction of burner liner structural performance and response; to calibrate, validate, and evaluate these predictive tools by comparing the predicted results with the experimental data; and to evaluate existing as well as advanced temperature and strain measurement instrumentation, through both contact and noncontact efforts, in a simulated turbine engine combustor environment. As the predictive tool, tests, test methods, instrumentation, and data acquisition and reduction methods are developed and evaluated, a proven, integrated analysis/experiment method will be developed that will permit the accurate prediction of the cyclic life of a burner liner.

Thompson, R. L.↗
NASA NTRS1985

High temperature stress-strain analysis

The objectives of the high temperature structures program are threefold: to assist in the development of analytical tools needed to improve design analysis and procedures for the efficient and accurate prediction of the nonlinear structural response of hot-section components; to aid in the calibration, validation, and evaluation of the analytical tools by comparing predictions with experimental data; and to evaluate existing as well as advanced temperature and strain measurement instrumentation.

Thompson, Robert L.↗
NASA NTRS1987

Failure modes for compression loaded angle-ply plates with holes

A combined theoretical-experimental investigation of failure in notched, graphite-epoxy, angle-ply laminates subjected to far-field compression loading indicates that failure generally initiates on the hole boundary and propagates along a line parallel to the fiber orientation of the laminate. The strength of notched laminates with specimen width-to-hole diameter ratios of 5 and 10 are compared to the strength of unnotched laminates. The experimental results are complemented by a three-dimensional finite element stress analysis that includes interlaminar stresses around holes in (+/- theta)s laminates. The finite element predictions indicate that failure is initiated by shear stresses at the hole boundary.

Burns, S. W.↗
NASA NTRS1986

High temperature stress-strain analysis

The objectives of the high-temperature structures program are threefold: to assist in the development of analytical tools needed to improve design analyses and procedures for the efficient and accurate prediction of the nonlinear structural response of hot-section components; to aid in the calibration, validation, and evaluation of the analytical tools by comparing predictions with experimental data; and to evaluate existing as well as advanced temperature and strain measurement instrumentation. As the analytical tools, test methods, tests, instrumentations, as well as data acquisition, management, and analysis methods are developed and evaluated, a proven, integrated analysis and experiment method will result in a more accurate prediction of the cyclic life of hot section components.

Thompson, Robert L.↗
NASA NTRS1987

Component specific modeling

The objective was to develop and verify a series of interdisciplinary modeling and analysis techniques specialized to address hot section components. These techniques incorporate data as well as theoretical methods from many diverse areas, including cycle and performance analysis, heat transfer analysis, linear and nonlinear stress analysis, and mission analysis.

Mcknight, R. L.↗
NASA NTRS1992

Analysis of stresses in finite anisotropic panels with centrally located cutouts

A method for analyzing biaxial- and shear-loaded anisotropic rectangular panels with centrally located circular and elliptical cutouts is presented in the present paper. The method is based on Lekhnitskii's complex variable equations of plane elastostatics combined with a boundary collocation method and a Laurent series approximation. Results are presented for anisotropic panels with elliptical cutouts and subjected to combined shear and compression loading. The effects on the stress field of panel aspect ratio, anisotropy, cutout size, and cutout orientation are addressed. Angle-ply laminates, unidirectional off-axis laminates, and ((+ or - 45/0/90)(sub 3))s, ((+ or - 45/0(sub 2))(sub 3))s, and ((+ or - 45/90(sub 2))(sub 3))s laminates are examined.

Britt, Vicki O.↗
NASA NTRS2000

NDE for Material Characterization in Aeronautic and Space Applications

This paper describes selected nondestructive evaluation (NDE) approaches that were developed or tailored at the NASA Glenn Research Center for characterizing advanced material systems. The emphasis is on high-temperature aerospace propulsion applications. The material systems include monolithic ceramics, superalloys, and high temperature composites. In the aeronautic area, the highlights are cooled ceramic plate structures for turbine applications, F-TiAl blade materials for low-pressure turbines, thermoelastic stress analysis (TSA) for residual stress measurements in titanium based and nickel based engine materials, and acousto ultrasonics (AU) for creep damage assessment in nickel-based alloys. In the space area, examples consist of cooled carbon-carbon composites for gas generator combustors and flywheel rotors composed of carbon fiber reinforced polymer matrix composites for energy storage on the international space station (ISS). The role of NDE in solving manufacturing problems, the effect of defects on structural behavior, and the use of NDE-based finite element modeling are discussed. NDE technology needs for improved microelectronic and mechanical systems as well as health monitoring of micro-materials and components are briefly discussed.

Baaklini, George Y.↗
NASA NTRS2003

TF41 Engine Fan Disk Seeded Fault Crack Propagation Test

Uncontained engine failures, although rare in occurrence, can have a catastrophic effect on aircraft performance and safety. Engine disk cracks can eventually lead to these type of failures. A number of techniques to detect engine disk cracks have been developed in recent years. However, these technologies have only been validated by disk spin pit tests, not actual engine tests. Due to this, a project was established to perform seeded fault engine tests on a TF41 engine disk fan. A defect was machined in the first stage fan disk of a TF41 engine. The disk was run in a spin pit to initiate a crack. Once initiated, the disk was run in an actual engine test facility. The engine was cycled by a number of start and stops with the goal of propagating the crack to disk burst through low cycle fatigue. Various crack detection techniques were installed on the engine and run real-time during the test to validate their abilities to detect disk cracks. These techniques were based on methods such as change in mass imbalance using vibration or shaft displacement, change in blade position, acoustic emission, and torsional resonance. At the completion of 4474 test cycles, the crack in the TF41 disk was determined to have grown approximately 0.025 inches. This was far less the predicted crack growth based on a fracture mechanics analysis and finite element stress analysis.

Lewicki, David G.↗
NASA NTRS2019

Development of a Design for Manufacturing Tool for Automated Fiber Placement Structures

Existing design processes for laminates constructed with automated fiber placement lack significant integration between the various software tools that compose the process. Tools for finite element analysis, computer aided drafting, stress analysis, tool path simulation, and manufacturing defect prediction are all critical parts of the design process. With traditional hand-layup laminates, the analysis performed with each of these tools could be fairly well decoupled from one another. However, for laminates generated by automated fiber placement, the disciplines can become significantly coupled, especially on structures with curvature. This gives rise to a need for integrated “design for manufacturing” software tools that are able to balance the competing objectives from each discipline. This paper describes the preliminary development of such a tool.

Noevere, August T.↗
NASA NTRSDate not supplied

Mechanical Erosion Modeling of TPS Materials

This work describes the development of a model that accounts for the additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics module was integrated within the Porous material Analysis Toolbox (PATO) based on OpenFOAM. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model capable to predict the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.

Stress Analysis↗
NASA NTRSDate not supplied

Mechanical Erosion Modeling of TPS Materials

This work describes the development of a model that accounts for the additional surface recession in Thermal Protection Systems (TPS) materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics module was integrated within the Porous material Analysis Toolbox (PATO) based on OpenFOAM. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model capable to predict the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.

Stress Analysis↗
NASA NTRSDate not supplied

Mechanical Erosion Modeling of TPS Materials

This work describes the development of a model that accounts for the additional total surface recession in Thermal Protection Systems materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics capability module was integrated within the Porous material Analysis Toolbox based on OpenFOAM, PATO. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver module computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model of the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.

Stress Analysis↗
NASA NTRS1977

Three dimensional finite-element analysis of finite-thickness fracture specimens

The stress-intensity factors for most of the commonly used fracture specimens (center-crack tension, single and double edge-crack tension, and compact), those that have a through-the-thickness crack, were calculated using a three dimensional finite-element elastic stress analysis. Three-dimensional singularity elements were used around the crack front. The stress intensity factors along the crack front were evaluated by using a force method, developed herein, that requires no prior assumption of either plane stress or plane strain. The calculated stress-intensity factors from the present analysis were compared with those from the literature whenever possible and were generally found to be in good agreement. The stress-intensity factors at the midplane for all specimens analyzed were within 3 percent of the two dimensional plane strain values. The stress intensity factors at the specimen surfaces were considerably lower than at the midplanes. For the center-crack tension specimens with large thickness to crack-length ratios, the stress-intensity factor reached a maximum near the surface of the specimen. In all other specimens considered the maximum stress intensity occurred at the midplane.

Raju, I. S.↗
NASA NTRS1935

Tension Fields in Originally Curved, Thin Sheets During Shearing Stresses

The analysis of the stresses in the sheet and stiffeners is predicated upon the direction of the wrinkles, particularly the tensile stresses (principal stresses). This analysis and the calculation of stresses after buckling form the subject of the present article. It includes: 1) metal cylinders with closely spaced longitudinal stiffeners; 2) metal cylinders with closely spaced transverse rings.

Wagner, H↗