A compendium of sources of fracture toughness and fatigue crack growth data for metallic alloys, part 4
A collection of sources is presented of fracture toughness and fatigue crack growth data for metallic alloys.
Hudson, C. Michael↗
SEARCH · Search NASA
Results for “TOUGH”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fracture-tough, corrosion-resistant bearing steels
The fundamental principles allowing design of stainless bearing steels with enhanced toughness and stress corrosion resistance has involved both investigation of basic phenomena in model alloys and evaluation of a prototype bearing steel based on a conceptual design exercise. Progress in model studies has included a scanning Auger microprobe (SAM) study of the kinetics of interfacial segregation of embrittling impurities which compete with the kinetics of alloy carbide precipitation in secondary hardening steels. These results can define minimum allowable carbide precipitation rates and/or maximum allowable free impurity contents in these ultrahigh strength steels. Characterization of the prototype bearing steel designed to combine precipitated austenite transformation toughening with secondary hardening shows good agreement between predicted and observed solution treatment response including the nature of the high temperature carbides. An approximate equilibrium constraint applied in the preliminary design calculations to maintain a high martensitic temperature proved inadequate, and the solution treated alloy remained fully austenitic down to liquid nitrogen temperature rather than transforming above 200 C. The alloy can be martensitically transformed by cryogenic deformation, and material so processed will be studied further to test predicted carbide and austenite precipitation behavior. A mechanistically-based martensitic kinetic model was developed and parameters are being evaluated from available kinetic data to allow precise control of martensitic temperatures of high alloy steels in future designs. Preliminary calculations incorporating the prototype stability results suggest that the transformation-toughened secondary-hardening martensitic-stainless design concept is still viable, but may require lowering Cr content to 9 wt. pct. and adding 0.5 to 1.0 wt. pct. Al. An alternative design approach based on strain-induced martensitic transformation during cryogenic forming, thus removing the high martensitic constraint, may permit alloy compositions offering higher fracture roughness.
Olson, Gregory B.↗
Fracture toughness of polyimide films
Two aromatic polyimides and an aromatic polyamide-imide were tested in single edge notched tension. Fracture toughnesses, normalized to 25 micron film thickness ranged from 1.65 to 5.4 MPa m sup 1/2. LARC-TPI, a thermoplastic polyimide, showed evidence of crazing ahead of a growing crack whereas the other materials formed a shear yielded zone.
Hinkley, J. A.↗
LaRC-RP41: A Tough, High-Performance Composite Matrix
New polymer exhibits increased toughness and resistance to microcracking. Cross-linking PMR-15 and linear LaRC-TPI combined to provide sequential semi-2-IPN designated as LaRC-RP41. Synthesized from PMR-15 imide prepolymer undergoing cross-linking in immediate presence of LaRC-TPI polyamic acid, also undergoing simultaneous imidization and linear chain extension. Potentially high-temperature matrix resin, adhesive, and molding resin. Applications include automobiles, electronics, aircraft, and aerospace structures.
Pater, Ruth H.↗
An evaluation of the fatigue crack growth and fracture toughness properties of beryllium-copper alloy CDA172
A series of fracture mechanics tests, using the Be-Cu alloy CDA172 in the round rod product form, was conducted in a lab air environment at room temperature. Tensile data is presented in both the L and C directions and K sub Ic data in both the C-R and C-L orientations. Fracture toughness values were derived from M(T) (center cracked), PS(T) (surface cracked) and CC01 (corner cracked) specimens of varying thickness. Fatigue crack growth data were obtained for the C-R orientation at stress ratio of 0.1, 0.4, and 0.7 and for the C-L orientation at stress ratios of 0.1, 0.3, 0.4, and 0.7.
Forman, Royce G.↗
High-toughness graphite/epoxy composite material experiment
The experiment was designed to measure the effect of near-space exposure on mechanical properties of specially toughened 5208/T300 graphite-epoxy composites. The properties measured are elastic modulus, strength, and fracture toughness. Specimens were mounted on an external frame during the time of the LDEF mission. Specimen variables include angle of adjacent plies and fraction of interlaminar contact, which is controlled by the fraction of finely spaced holes in Mylar film placed between the prepreg monolayers of the composite.
Felbeck, David K.↗
The effect of temperature on the fracture toughness of Weldalite(TM) 049
The uncertain effect of temperature is characterized on the deformation and fracture behavior of Weldalite(TM) 049 from cryogenic to elevated temperatures. Fracture resistance is measured and the determination of fracture mechanisms emphasized, including slip plane cracking, high angle boundary delamination, subgrain boundary cracking, and microvoid coalescence. Microstructure is controlled to produce either predominantly T(sub 1) or T(sub 1) + delta (after Blankenship and Starke) and to examine the effect of dislocation-precipitate interaction on fracture toughness.
Lach, Cynthia L.↗
Prospects for Ductility and Toughness Enhancement of Nial by Ductile Phase Reinforcement
The use of NiAl as a structural material has been hindered by the fact that this ordered intermetallic does not exhibit significant tensile ductility or toughness at room temperature. A critical review of the operative flow and fracture mechanisms in monolithic NiAl has thus established the need for ductile phase toughening in this order system. Progress in ductile phase reinforced intermetallic systems in general and specifically NiAl-based materials has been reviewed. In addition, further clarification of the primary mechanisms involved in the flow and fracture of ductile phase reinforced alloys has evolved from ongoing investigations of several model NiAl-based materials. The mechanical behavior of these model directionally-solidified alloys (Ni-30Al and Ni-30Fe-20Al) are discussed. Finally, the prospects for developing a ductile phase toughened NiAl-based alloy and the shortcomings presently inherent in these systems are analyzed.
Noebe, R. D.↗
Composite structure global fracture toughness via computational simulation
A computational method for the simulation of damage and fracture propagation in laminated composites is presented. A quantitative evaluation of the global fracture toughness of composites is shown as a tool for monitoring the fracture stability of composites under sustained loading. Changes in overall structural properties such as natural frequencies and the fundamental buckling load are also computed with increasing load-induced damage. Structural degradation, delamination, fracture, and damage propagation are included in the simulation. An angle-plied composite plate structure subjected to inplane tensile loading is used as an example to demonstrate some of the feature of the computational method.
Minnetyan, L.↗
The effect of hydrogen on the fracture toughness of oxygen-strengthened titanium
Studies of oxygen-strengthened titanium alloys have indicated that while hydrogen has little effect on tensile properties, it causes a marked decrease in impact strength. It is presently established experimentally that the presence of hydrogen has essentially no effect on the fracture-toughness factor at the onset of crack propagation, in commercial-grade titanium alloys containing either low or high concentrations of oxygen. These findings are congruent with other study results on the tensile properties of these alloys, but contrast with the previously noted pronounced effect of hydrogen on impact resistance.
Wasz, M. L.↗
Tough, high performance, addition-type thermoplastic polymers
A tough, high performance polyimide is provided by reacting a triple bond conjugated with an aromatic ring in a bisethynyl compound with the active double bond in a compound containing a double bond activated toward the formation of a Diels-Adler type adduct, especially a bismaleimide, a biscitraconimide, or a benzoquinone, or mixtures thereof. Addition curing of this product produces a high linear polymeric structure and heat treating the highly linear polymeric structure produces a thermally stable aromatic addition-type thermoplastic polyimide, which finds utility in the preparation of molding compounds, adhesive compositions, and polymer matrix composites.
Pater, Ruth H.↗
On improving the fracture toughness of a NiAl-based alloy by mechanical alloying
Mechanical alloying (MA) has been used to process the NiAl-based alloy Ni-35Al-20Fe, such that a fine-grain (about 2 microns) microstructure is obtained through the addition of 2 vol pct Y2O3 particles. When compared to a conventionally processed, coarse-grained (about 28 microns) Ni-35-20 alloy without the Y2O3 particles, the MA alloy exhibits two to three times higher fracture toughness values, despite a 50-percent increase in yield strength. Room-temperature K(O) values as high as 34 MPa sq rt m are observed, accompanied by a yield strength in excess of 1100 MPa. Fractography confirms a change in fracture characteristics of the fine-grained MA alloy.
Kostrubanic, J.↗
Redesign of the mixed-mode bending test for delamination toughness
The mixed-mode bending (MMB) test uses a lever to simultaneously apply mode I and mode II loading to a split-beam specimen. A nonlinear, iterative analysis that accurately predicts the measured load-displacement response and the strain energy release rate, G, of an MMB test, has shown that the errors in G calculated using linear theory can be quite large. The nonlinear analysis was used as a guide in redesigning the MMB apparatus. With the redesigned apparatus, loads are applied through a roller attached to the lever and loaded just above the midplane of the test specimen. The redesigned MMB apparatus has geometric nonlinearity errors of less than 3 percent, even for materials substantially tougher than APC2 (AS4/PEEK). This apparatus was demonstrated by measuring the mixed-mode delamination fracture toughness of APC2. The data from the redesigned MMB apparatus were analyzed with a linear analysis which yielded results similar to those found with the original apparatus and the nonlinear analysis.
Reeder, J. R.↗
Laboratory Powder Metallurgy Makes Tough Aluminum Sheet
Aluminum alloy sheet exhibits high tensile and Kahn tear strengths. Rapid solidification of aluminum alloys in powder form and subsequent consolidation and fabrication processes used to tailor parts made of these alloys to satisfy such specific aerospace design requirements as high strength and toughness.
Royster, D. M.↗
Analysis of precracking parameters and fracture toughness for ceramic single-edge-precracked-beam specimens
The single-edge-precracked-beam (SEPB) method involves creation of a straight-through crack from an indentation crack. The straight-through crack is developed by applying a controlled bending load to a specimen via a precracking fixture. The fixture induces the following sequence: (1) stable growth of the indentation crack; (2) pop-in; and finally, (3) arrest-thereby forming a straight-through precrack. The effects of indentation load on precracking load as well as precrack size were studied for experimental variables such as specimen width, fixture span, and material. Finite element analysis was used to obtain the stress distribution and stress intensity factor, thus providing a quantitative prediction of the precracking load and precrack size for silicon nitride, alumina, silicon cabide, and two SiC whisker-reinforced silicon nitrides. Fracture toughness values obtained from the SEPB method were compared with those obtained from other methods.
Choi, Sung R.↗
A tough high performance composite matrix
This invention is a semi-interpenetrating polymer network which includes a high performance thermosetting polyimide having a nadic end group acting as a crosslinking site and a high performance linear thermoplastic polyimide. An improved high temperature matrix resin is provided which is capable of performing in the 200 to 300 C range. This resin has significantly improved toughness and microcracking resistance, excellent processability, mechanical performance and moisture and solvent resistances.
Pater, Ruth H.↗
Fracture toughness testing of polymer matrix composites
The experimental techniques and associated data analysis methods used to measure the resistance to interlaminar fracture, or 'fracture toughness', of polymer matrix composite materials are described. A review in the use of energy techniques to characterize fracture behavior in elastic solids is given. An overview is presented of the types of approaches employed in the design of delamination-resistant composite materials.
Grady, Joseph E.↗
Poly(arylene ether-co-imidazole)s as toughness modifiers for epoxy resins
A toughened epoxy was prepared by reacting an epoxy resin with a poly(arylene ether-co-imidazole)s (PAEI). The epoxy resin comprises N,N,N',N'tetraglycidyl-4,4'- methylenebisbenzenamine and 4-aminophenyl sulfone. The PAEI was prepared by reacting an aromatic bisphenol, a bisphenol imidazole, and an activated aromatic dihalide or dinitro compound in the presence of potassium carbonate in a polar aprotic solvent at an elevated temperature. The epoxies which were modified with these particular PAEI's showed a significant increase in toughness with only a 10 weight percent loading of the PAEI into the epoxy. These toughened epoxies were used to prepare composites and molded parts.
Mcdaniel, Patricia D.↗