Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile Strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

10° off-axis testing of CFRP using DIC: A study on strength, strain and modulus

For the determination of the shear properties such as strength, strain and modulus of unidirectionally reinforced composites, nearly a dozen measurement techniques exist, several of which have found their way into standards. One non-standardized method for sheet materials is the 10° off-axis tensile test of unidirectional coupons. The current work focuses on the experimental investigation of tensile testing of CFRP-UD coupon specimens using the 10° off-axis test and DIC strain mapping to measure the full-field deformation response. A sensitivity analysis on the measured stresses, strains and moduli is performed by varying the aspect ratio of the specimens and the location of strain measurement. Test related uncertainties such as the loading angle and specimen preparation details are investigated and quantified with the help of these full-field DIC measurements.

42 ENGINEERING↗
DOE OSTI2024

Experimental Examination of Additively Manufactured Patterns on Structural Nuclear Materials for Digital Image Correlation Strain Measurements

Abstract Background There are a limited number of commercially available sensors for monitoring the deformation of materials in-situ during harsh environment applications, such as those found in the nuclear and aerospace industries. Such sensing devices, including weldable strain gauges, extensometers, and linear variable differential transformers, can be destructive to material surfaces being investigated and typically require relatively large surface areas to attach (> 10 mm in length). Digital image correlation (DIC) is a viable, non-contact alternative to in-situ strain deformation. However, it often requires implementing artificial patterns using splattering techniques, which are difficult to reproduce. Objective Additive manufacturing capabilities offer consistent patterns using programmable fabrication methods. Methods In this work, a variety of small-scale periodic patterns with different geometries were printed directly on structural nuclear materials (i.e., stainless steel and aluminum tensile specimens) using an aerosol jet printer (AJP). Unlike other additive manufacturing techniques, AJP offers the advantage of materials selection. DIC was used to track and correlate strain to alternative measurement methods during cyclic loading, and tensile tests (up to 1100 µɛ) at room temperature. Results The results confirmed AJP has better control of pattern parameters for small fields of view and facilitate the ability of DIC algorithms to adequately process patterns with periodicity. More specifically, the printed 100 μm spaced dot and 150 μm spaced line patterns provided accurate measurements with a maximum error of less than 2% and 4% on aluminum samples when compared to an extensometer and commercially available strain gauges. Conclusion Our results highlight a new pattern fabrication technique that is form factor friendly for digital image correlation in nuclear applications.

Novich, K. A. (ORCID:0000000204466022)↗
DOE OSTI2025

Production of Creep-Resistant FeCrAl-ODS

Four ODS FeCrAl alloys with base alloy composition Fe-16Cr-4Al-2Mo-0.2Y (wt.%) were mechanically alloyed with minor additions of CeO 2 and Y 2 O 3 additions and were successfully extruded into rectangular-shaped bars. Two oxide compositions were explored, which were designated NC with oxide addition of 0.5CeO 2 plus 0.2Yin solution of the base alloy powder and PC with additions of 0.5CeO 2 and 0.7Y 2 O 3 to elevate the O level. The microstructure of both alloys revealed by SEM and EBSD to consist of very small grains with sizes of ~450-520 nm and weak texture components. Sub-size tensile specimens fabricated from both alloys were tensile tested from room temperature to 800ºC. The results for both alloys from room temperature to 400ºC showed very high strengths, but low ductilities, especially uniform strain. From 500ºC to 800ºC, the strengths decreased rapidly, and the ductilities increased significantly. The reason for the rapid decreases in tensile strengths above 500ºC for both alloys is not clear, but will require advanced characterization techniques including atom probe tomography, to determine the size and number density of the nano-size oxide particles, and TEM/EFTEM, for investigating the dispersion of nano-size oxide particles on grain boundaries to assess the Zener grain boundary pinning effect, which will hinder grain coarsening at high temperatures that may enhance the Hall Petch strengthening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Controlling mechanical properties of laser powder bed fused AlSi10Mg through manipulation of laser scan rotation

The microstructure and mechanical properties of laser powder bed fused (LPBF) AlSi10Mg alloys can be controlled by many processing parameters. This study focuses on the scan rotation angle, α, between adjacent layers, and establishes the relationship between α and tensile behavior of the as-built LPBF-processed AlSi10Mg alloy. Near-full density cubic coupons were manufactured using the same processing parameters but with systematic variation of α from 0° to 90°. Microscopic observations and X-ray diffraction analysis showed that differences among various coupons mainly include orientations of the melt pools with respect to the build direction and development of the crystallographic texture. The α=0° coupon and α=30° coupon showed the highest and lowest texture index, although the overall crystallographic texture was mild. Tensile specimens were manufactured horizontally and vertically using either α=0° or α=30°, but with various first layer laser direction with respect to the build plate. Notably, the α=0° specimen that was tested along the laser scan direction showed the largest yield strength (283 MPa) and highest tensile ductility (10.1 %). Quantitative image analysis and fractography were performed on all specimens. Results showed that the melt pool orientation with respect to the tensile direction affected the tensile behavior across the different specimens. This was closely related to the localized strain distribution within the melt pool and along the melt pool boundary for the different melt pool orientations observed. Further, these results demonstrate that the laser scan rotation angle between layers can be used to fine tune the mechanical properties of LPBF AlSi10Mg alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of grain boundary crystallography on void growth in FCC metals

The growth of an isolated spherical void at and near a grain boundary or a triple junction is studied by means of full-field crystal plasticity simulations with explicit representation of the void. To examine the fundamental aspects of void/grain boundary interactions in these cases, a three-dimensional large-strain elasto-viscoplastic fast-Fourier transform (LS-EVP-FFT) model with axisymmetric tensile periodic boundary conditions was developed. We employ this model to reveal the role of crystallography (grain orientations, grain boundary misorientation and inclination angle with respect to the largest component of the applied stress) and type of loading on void growth. It was found that grain orientation was the primary crystallographic feature governing void growth in strain-rate controlled simulations. For strains small enough to not significantly alter the local geometry, the overall growth of the void in bicrystal boundaries was not strongly affected by grain boundary inclination angle. The relative amount of void growth experienced within each grain in a bicrystal or tri-crystal was strongly dependent on the grain boundary inclination angle. We found a subset of orientations that exhibit faster void growth in bicrystal boundaries than inside the constituent single crystals. Last, we show that when placed primarily in one grain but near the grain boundary, void growth was similar to void growth when placed at the grain boundary. Furthermore, the growing void remained in the original grain and did not grow into the other grain, regardless of crystallographic character.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗
DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

ACT University Collaboration Proposal: Role of manufacturing defects on material failure under dynamic loading for developing enhanced failure models and theories (Final Report)

Research on the tensile behavior of additively manufactured 316L stainless steel coupon specimens at increasing strain rates was conducted over the past year at Penn State. Dynamic loading rates into the 1000 1/s loading rates were performed on specimens with nearly 1.32” gage lengths. Stress-strain plots show ductile and plastic behavior well beyond 12% strain with necked specimens, having smaller effective gage lengths showing up to 56% ultimate strain. Additional tests performed on compact tension specimens helped with simulation work to understand the deformation behavior. Using finite elements, it was possible to determine the feasibility of a comprehensive experimental validation study towards an improved model for AM material failure – specifically, the Bai-Wierzbicki approach which accounts for lode angle and triaxiality. A non-significant number of tests are projected for eight specific failure nodes, with additional replicates to provide strain-rate capabilities to the existing formulation. One such correction factor is explored for quasi-static, notched specimens. Finally, stress intensity factor was explored using a set of compact-tension specimens which would also provide useful validation data for any simulation work.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quality Investigation of Pultruded Carbon Fiber Panels Subjected to Four-Point Flexure via Fiber Optic Sensing

Pultruded carbon fiber-reinforced composites are attractive to the wind energy industry due to the rapid production of highly aligned unidirectional composites with enhanced fiber volume fractions and increased specific strength and stiffness. However, high volume carbon fiber manufacturing remains cost-prohibitive. This study investigates the feasibility of a pultruded low-cost textile carbon fiber-reinforced epoxy composite as a promising material in spar cap production was undertaken based on mechanical response to four-point flexure loading. As spar caps are primarily subjected to flexural loading, large-span four-point flexure was considered, and coupon testing was restricted to tensile modulus and compression strength assessment. High-resolution spatial fiber optic strain sensing was utilized to determine spatial strain distribution during four-point flexure, revealing consistent strain along the length of the part and proved to be an excellent option for process manufacturing quality examination. Additionally, holes with diameters of 2.49 mm, 5.08 mm, and 1.93 mm were drilled through the thickness of full-width parts to determine the feasibility of structural health monitoring of pultruding parts internal to wind blades via fiber optic strain sensing.

Chemistry↗
DOE OSTI2022

In-situ synchrotron X-ray diffraction investigation on deformation behavior of Nb/NiTi composite during pre-straining process

The mechanisms responsible for deformation behavior in Nb/NiTi composite during pre-straining were investigated systematically using in-situ synchrotron X-ray diffraction, transmission electron microscopy and tensile test. It is shown that upon loading, the composite experiences elastic elongation and slight plastic deformation of B19', B2 and β-Nb phases, together with the forward stress-induced martensitic (SIM) transformation from B2 to B19'. Upon unloading, the deformation mechanisms of the composite mainly involve elastic recovery of B19', B2 and β-Nb phases, compression deformation of β-Nb phase and incomplete B19'→B2 reverse SIM transformation. In the tensile loading-unloading procedure, besides the inherent elastic deformation and SIM transformation, the (001) compound twins in B19' martensite can also be conducive to the elastic deformation occurring in B19'-phase of the composite. Therefore, this composite can exhibit a large recoverable strain after unloading owing to the elastic deformation, and the partially reversible and consecutive SIM transformation together with the (001) compound twins.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the asymmetric orientations and stress states in polycrystalline NiTi SMA by in-situ synchrotron-based high-energy X-ray diffraction

The stress-induced martensite transformations (SIMTs) dramatically affect the recoverable strain and mechanical response of polycrystalline NiTi. An in-depth understanding of the propagation manner and orientation preference of SIMTs is therefore crucial. Here, in this work, we present a unique asymmetric anisotropy of SIMTs and lattice strains induced by Lüders-type deformation in polycrystalline NiTi, achieved through a combination of in-situ synchrotron X-ray diffraction and uniaxial tensile loading and unloading experiments. Our experimental findings reveal that in polycrystalline NiTi under uniaxial deformation, the asymmetry of SIMTs is attributed to the inhomogeneous strain field caused by the Lüders-type mechanism. The asymmetrical SIMT starts with the forward Lüder band and disappears along with the backward Lüder band. The austenite with the favored orientation of $\langle$110$\rangle$ A //loading direction (LD) transformed and recovered back at a higher rate compared to other orientations during both loading and unloading.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Advanced Manufactured Strain Sensors for Extreme Environments

Experimentation at irradiation test facilities are essential for reducing the innovation time of developmental fuels, fuel cladding, and structural materials employed in next-generation nuclear reactors. However, due to the harsh conditions generated in such reactors and limited instrumentation space, the evaluation of a material’s mechanical properties is often limited to characterization after the materials have been removed from reactor conditions, or post-irradiation examination. These experiments are costly, time-consuming, and fail to capture the critical time-evolving phenomena that occur during the irradiation experiments. Advanced manufactured digital image correlation patterns and strain sensor devices serve as two promising technologies that can be deployed in the confined and challenging orientations of these irradiation experiments while also providing key insight on salient materials phenomena (i.e., mechanical properties). To guide the development of the printed strain sensors prior to their deployment in critical experiments, the adhesion strength between the substrate and printed film interface is measured via tensile testing and a non-contact laser-induced spallation technique. The establishment of these process control steps helped guide the successful fabrication and testing of direct-write strain sensing devices discussed in this work. The fabrication process controls are necessary for enabling the sustained operation of these strain sensing device through experimentation and minimize the potential for premature failure.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Advanced Manufactured Strain Sensors for Extreme Environments

Experimentation at irradiation test facilities are essential for reducing the innovation time of developmental fuels, fuel cladding, and structural materials employed in next-generation nuclear reactors. However, due to the harsh conditions generated in such reactors and limited instrumentation space, the evaluation of a material’s mechanical properties is often limited to characterization after the materials have been removed from reactor conditions, or post-irradiation examination. These experiments are costly, time-consuming, and fail to capture the critical time-evolving phenomena that occur during the irradiation experiments. Advanced manufactured digital image correlation patterns and strain sensor devices serve as two promising technologies that can be deployed in the confined and challenging orientations of these irradiation experiments while also providing key insight on salient materials phenomena (i.e., mechanical properties).To guide the development of the printed strain sensors prior to their deployment in critical experiments, the adhesion strength between the substrate and printed film interface is measured via tensile testing and a non-contact laser-induced spallation technique. The establishment of these process control steps helped guide the successful fabrication and testing of direct-write strain sensing devices discussed in this work. The fabrication process controls are necessary for enabling the sustained operation of these strain sensing device through experimentation and minimize the potential for premature failure.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗