Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermal modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Quantifying thermal barrier coating delamination through luminescence modeling

Thermal barrier coatings (TBCs) are widely used in the hot sections of gas turbine systems as they are remarkably efficient in insulating the underlying superalloys, leading to higher operating temperatures and therefore enhancing the performance of the engines. However, this benefit is only possible if the integrity of the TBC under aggressive thermo-mechanical environments is ensured. Delamination is a common but hard to detect failure mode. We present, in this work, supported by experimentation, the implementation of a modeling approach applying the Kubelka-Munk theory to provide numerical quantification of luminescence contrast and intensity due to top coat delamination in TBCs. The method relies on the drastic change in reflectivity when a delamination forms, exploiting it for high-contrast luminescence mapping. Two distinct TBC configurations containing an erbium-doped yttria-stabilized zirconia (YSZ:Er 3+ ) layer for delamination sensing were used to validate this model. A delamination zone induced by Rockwell indentation was successfully tracked by measuring an increase of the intensity of the erbium emission line at 562 nm. Luminescence-based methods for delamination detection can provide a revolutionary non-invasive technique, with potential for both off-line and on-line engine monitoring.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Improved internal short circuit models for thermal runaway simulations in lithium-ion batteries

Thermal runaway (TR) modeling is one of the primary tools that can be used to overcome challenges associated with lithium-ion battery (LIB) safety. Among all LIB accidents that have occurred over the past decade, Internal Short Circuit (ISC) remains the most common trigger mechanism. Many available models in the literature either use a simplified approach to simulate ISC or completely ignore its contribution. The aim of this study is to understand the nature of the heat released for different types of ISC scenarios, including aluminum-anode, anode–cathode, and copper-cathode ISC. We study ISC behavior using a coupled electrochemical–thermal model with an integrated TR chemical kinetics solver built in the COMSOL Multiphysics framework. The time duration of heat release and the magnitude of the peak ISC current are studied as functions of parameters such as the size of the penetrating filament and the capacity of the cell. The numerical results are used to build an empirical model validated against the published experimental TR propagation data. Our model can be successfully used as a viable low-cost substitute in lower order (lumped) TR simulations to enable TR prevention and mitigation.

Singh, Bakhshish Preet (ORCID:0000000264751992)↗
DOE OSTI2021

Phonon gas model for thermal conductivity of dense, strongly interacting liquids

Developing predictive thermal property models for liquids based on microscopic principles has been elusive. The difficulty is that liquids have gas-like and solid-like attributes that are at odds when considering the frameworks of microscopic models: Models for gases are simple due to randomness and low density, whereas models for crystalline solids rely on symmetry and long-range order for easier calculation. The short-range order in liquids does, however, provide structure to neighboring molecules similar to amorphous solids, and there have been recent advances indicating that collective vibrational modes store heat in liquids. Models combining Debye approximations from solid-state physics and Frenkel’s theory of liquids can accurately predict the heat capacity of liquids. Phonon-like dispersions in liquids have also been widely observed in neutron scattering experiments. These developments motivate us to propose a model where high-frequency vibrational modes, which travel at the speed of sound and have a mean free path on the order of the average intermolecular distance, conduct heat in liquids. We use this liquid phonon gas model to calculate the thermal conductivity of liquids with varying intermolecular interaction energies from strongest to weakest—Coulomb, hydrogen-bonding, Keesom, and London dispersion energy. Generally, the model is more accurate as the intermolecular interaction energy and density of liquids increase. The calculated thermal conductivity of Coulombic-bound molten sodium nitrate and hydrogen-bonded water is within 1.46% and 2.98% of the experimentally measured values, respectively, across their entire temperature ranges. Further modal analysis of the velocity and the mean free path of collective vibrations could establish the liquid phonon gas model as an accurate model for weakly interacting liquids as well.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Space shuttle thermal scale modeling application study

The critical thermal control problems and verification of thermal mathematical model results for the space shuttle concept are discussed. The use of a small scale thermal model of the space shuttle is proposed. It was determined that a one-third scale model of the space shuttle would serve as a useful tool throughout the entire thermal design and verification program. The major considerations in modeling the conduction-radiation-convection fields, the level of detail for modeling various systems, preliminary test requirements, and potential applications of the thermal scale model are summarized.

Marshall, K. N.↗
DOE OSTI2024

Modeling delayed thermal runaway in nitric acid-soaked cat litter mixed with radioactive waste

Thermal ignition of radioactive waste within a 55-gallon drum was simulated by using a pressure-dependent waste decomposition model (Hobbs et al. in Process Saf Environ Prot https://doi.org/10.1016/j.psep.2022.09.047, 2022) calibrated with data from full-scale drum experiments (Parker et al. in The thermolytic response of a surrogate RNS waste mixture at the drum scale. Los Alamos National Laboratory Report LA-UR-16-21760, 2016) and validated with experiments from multiple laboratories (Hobbs et al. in Thermal analysis of aged nitric acid-soaked kitty litter in TRU waste drums-23370.WM2023 Conference, Phoenix, AZ, 2023). The acceleration of nitric acid chemistry reacting with an organic cat litter leading to thermal ignition was likely triggered by a restricted vent in the drum. Here, we address whether the form of the rate equation in (Hobbs et al. in Process Saf Environ Prot https://doi.org/10.1016/j.psep.2022.09.047, 2022) is sufficient to extrapolate thermal ignition within aged drums of similar content that have been stored in Texas for over nine years by investigating four different reaction rate forms for waste decomposition. A critical reaction rate reduction analysis is performed on each of these models to determine if delayed thermal runaway within vented aged waste is possible after nine years. We found that a pressure-dependent first-order rate expression not only predicted the accidental ignition of the waste drum, but the form also matches multiple experiments from different laboratories. Even though the waste composition decreases over time, the model predicts that acceleration leading to thermal runaway is possible if the waste is confined, even after 9 years. In conclusion, waste containing oxidizers such as nitric acid should not be mixed with organic adsorbents, especially if the waste is confined.

cookoff↗
NASA NTRSDate not supplied

Multiscale Thermal Conductivity Modeling of 3D Woven Composite Thermal Protection System Materials

Novel thermal protection systems (TPS) for re-entry and hypersonic vehicles utilize 3D woven composite materials with blended carbon filament tows (yarns) and a phenolic resin matrix. The presence of continuous carbon fibers provides superior stiffness and strength compared to legacy TPS, while the 3D weave pattern provides a great deal of design flexibility for both in-plane and through thickness thermomechanical behavior. However, modeling of 3D woven composites is notoriously complex and numerically intensive. The present investigation utilizes a unique ultra-efficient approach, known as Multiscale Recursive Micromechanics (MsRM), wherein recursive semi-analytical micromechanics methods are employed at various length scales within the composite. The MsRM approach has recently been extended to solve for the effective thermal conductivity as well as the local temperature and thermal flux fields throughout the composite. Presented model results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures, for a novel 3D woven TPS.

Composite↗
NASA NTRS1984

Predictive thermal-vacuum modeling by variable coefficients

In computer-assisted thermal-vacuum testing, an accurate mathematical thermal model is necessary. This model can indicate what effect a given change in control temperature will produce on the test article. A three-node thermal model is used to illustrate some numerical methods for increasing the accuracy by generating more accurate coefficients for the model.

Chuvala, J. T.↗
NASA NTRS2000

Experimental and Numerical Characterization of a Cylindrical Blackbody Cavity

During hypersonic flight, high temperatures and high heat fluxes are generated on the surfaces of vehicles. The Flight Loads Laboratory (FLL) at Dryden Flight Research Center (DFRC) is equipped with a calibration furnace, capable of calibrating heat flux gages up to 1100kW per square meters, and temperature sensors up to 2600 C. One heating configuration of the calibration furnace is a cylindrical blackbody cavity. Throughout the blackbody there are temperature gradients due to various boundary conditions. These boundary conditions include resistance heating, radiant heat transfer, and conduction to water-cooled electrodes. Also, an inert gas is purged through the graphite blackbody to prevent it from oxidizing. Consequently, the various modes of heat transfer present during operation of the blackbody cavity must be well understood in order to produce accurate heat flux gage and temperature sensor calibrations for use in ground testing or flight testing of hypersonic vehicles. The first step towards understanding the heat transfer in the blackbody cavity was to perform experiments at 1100 C, with and without outer surface insulation, while taking detailed temperature measurements inside the blackbody cavity. Steady state thermal models of the blackbody cavity were then developed. These models included detailed thermal analysis using commercial thermal analysis software. Conduction, radiation, and convection were considered in the thermal models for two cases: one with the outside of the blackbody cavity insulated and the second without insulation. This paper describes the experimental and numerical efforts used to characterize the steady state operation of the blackbody cavity. It describes the analysis of the test measurements, the boundary conditions used in the numerical models, and how the models were calibrated to fit the experimental data. Effects of various uncertainties, such as material properties, and convection are discussed.Initial thermal models predicted temperatures in the deepest part of the blackbody cavity within 7 C of the measured value and produced trends comparable to the experimental data, throughout the models. Adjustment of the boundary conditions, which were included in the thermal models, produced good agreement with measured temperatures. Free and forced convection of the purge gas inside the blackbody was found to be insignificant.

Abdelmessih, Amanie N.↗
NASA NTRS1990

Modeling of thermal lensing in side and end-pumped finite solid-state laser rods

An analytical expression for approximating the time-dependent thermal focal length in finite solid state laser rods was derived. The analysis is based on the temperature variation of the material refractive index caused by optical pumping of these rods. Several quantities were found to be relevant to this analysis. These quantities were the specific thermal profiles of the rods, type of optical pumping employed, type of cooling scheme employed (side and end-cooling parameters), and the specific material characteristics of the rods. The Thermal Lensing Model was formulated using the geometric ray tracing approach. The focal lengths are then approximated, by calculating the phase shift in the index of refraction, as the different rays of an incident plane wave are tracked through a lens-like crystal medium. The approach also applies in the case of Gaussian or parabolic pump beams. It is shown that the prediction of thermal focal length is in good quantitative agreement with experimentally obtained data.

Brackett, Vincent G.↗
DOE OSTI2020

Frequency-domain hot-wire sensor and 3D model for thermal conductivity measurements of reactive and corrosive materials at high temperatures

High temperature solids and liquids are becoming increasingly important in next-generation energy and manufacturing systems that seek higher efficiencies and lower emissions. Accurate measurements of thermal conductivity at high temperatures are required for the modeling and design of these systems, but commonly employed time-domain measurements can have errors from convection, corrosion, and ambient temperature fluctuations. Here, we describe the development of a frequency-domain hot-wire technique capable of accurately measuring the thermal conductivity of solid and molten compounds from room temperature up to 800 °C. Therefore, by operating in the frequency-domain, we can lock into the harmonic thermal response of the material and reject the influence of ambient temperature fluctuations, and we can keep the probed volume below 1 µl to minimize convection. The design of the microfabricated hot-wire sensor, electrical systems, and insulating wire coating to protect against corrosion is covered in detail. Furthermore, we discuss the development of a full three-dimensional multilayer thermal model that accounts for both radial conduction into the sample and axial conduction along the wire and the effect of wire coatings. The 3D, multilayer model facilitates the measurement of small sample volumes important for material development. A sensitivity analysis and an error propagation calculation of the frequency-domain thermal model are performed to demonstrate what factors are most important for thermal conductivity measurements. Finally, we show thermal conductivity measurements including model data fitting on gas (argon), solid (sulfur), and molten substances over a range of temperatures.

47 OTHER INSTRUMENTATION↗
NASA NTRS1979

Wing shape optimization for maximum cross-country speed, with mathematical programming

A computer program was developed to calculate numerically the speed and circling polars of an aircraft when the lift and drag characteristics of the wing airfoils are known. The planform of the wing is described by variables which are optimized so that the cross-country speed of the glider is maximum for the particular type of thermal model. Two thermal models are compared and shown that with a greater wing area than now normally used the performance can be increased.

Helwig, G.↗
NASA NTRS2019

Thermal Environment Modeling Practices for the Descent Trajectory of Lunar Landers

With the current push to send landers back to the moon, properly modeling the thermal environment for the descent is critical. Descent in this paper is described as: descending from low lunar orbit to touch down on surface. There are several challenges during this period, including: many electronics (such as battery, avionics, transponder, etc…) have higher heat loads due to higher power levels, a significant portion of the view factor to space has been blocked out by the moon making heat rejection less efficient, components that normally do not have direct line of sight to the sun may get exposure due to the lander rotating to align for descent, and thruster firing will dump more heat into the lander. All of these factors combine during the most critical phase of a lander mission make it essential that the thermal environment has been properly set up during design and analysis. This paper presents one method of setting up the thermal environment during descent in Thermal Desktop and will also include some tips and tricks.

Szerszen, Alexander↗
NASA NTRS2023

Thermal Desktop Modeling of the RRM3 On-Orbit Cryogenic Methane Storage and Active Cooling Experiment

The storing of cryogenic propellants is an enabling technology for NASA as it moves to expand future missions into low Earth orbit (LEO) and beyond. The Robotic Refueling Mission–3 (RRM3) experiment launched in 2018 and was designed to demonstrate tank self-pressurization during storage and active cooling of liquid methane in microgravity. Creating accurate models using existing datasets from flight experiments such as RRM3 is a vital step toward developing appropriate modeling tools to form pre-test predictions for future flight systems. The goal of this work was to create a working model in Thermal Desktop of the RRM3 source Dewar during the microgravity self-pressurization experiment. The pressure rise, temperature distribution of the fluid inside the tank, and the wall temperatures were all tracked and compared with test data. Initial results show good agreement between each of these metrics and the experimental results. This work is ongoing and will yield further insights into the thermal behavior of cryogens in microgravity.

Tank self-pressurization↗
NASA NTRS1972

Thermal dynamic modeling study

Some thermal dynamic requirements associated with the space shuttle vehicle are reviewed. Pertinent scaling laws are discussed and recommendations are offered regarding the need for conducting reduced-scale dynamic tests of major components at elevated temperatures. Items considered are the development and interpretation of thermal dynamic structural scaling laws, the identification of major related problem areas and a presentation of viable model fabrication, instrumentation, and test procedures.

Ojalvo, I. U.↗
DOE OSTI2022

Building Model Calibration: Validation of GridLAB-D Thermal Dynamics Modeling

This report investigates how well GridLAB-D’s house model characterizes the thermal dynamics of buildings given the overpredicted diurnal electric load swing observed in the Distribution System Operation with Transactive (DSO+T) study. This study seeks to validate GridLAB-D’s house model by calibrating it to data from the well-instrumented Pacific Northwest National Laboratory Lab Homes in Richland, WA. The datasets chosen included multiple pre-cooling and pre-heating testing periods where the indoor air temperature was allowed to float over a multi-hour length of time to mimic diurnal behavior. The multi-season calibrations were evaluated by comparing the heating/cooling electric power, indoor air temperature, and the rise/decay time during temperature float periods with Lab Homes data. The default GridLAB-D assumptions for latent load fraction, air heat capacity, mass heat capacity, window-to-wall-ratio, overall envelope conductance (assumed as NORMAL thermal integrity level), and solar heat gain coefficient were compared with the calibrated model to confirm when the default assumptions were adequate and the impact of calibration on the accuracy of modeling the thermal dynamics of homes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1987

Development of OPTIMOD - The new Space Shuttle Orbiter/Payload Thermal Integration Model

The development of the Orbiter/Payload Thermal Integration Model (OPTIMOD), a simplified Space Shuttle Orbiter thermal math model to be used for payload thermal integration analysis, is described. The Orbiter lower fuselage math model has been reduced to the minimum level of detail consistent with accuracy requirements. Instead, an 'environment radiation sensor', a simple closed-end cylinder oriented in a fixed position with respect to the Orbiter, is introduced. Equations are presented which relate the cylinder surface heating rates to external fuselage steady-state temperatures. These equations were derived from a regression correlation analysis of steady-state Orbiter thermal solutions for 2372 points on orbit, representing a complete range of vehicle-earth-sun orientations. An exponential equation is developed to relate the steady-state data to time-variant temperatures for the particular transient attitude timeline being simulated. The accuracy of OPTIMOD is shown to be excellent in the payload bay and to compare favorably with previous models in Orbiter elements outside the bay.

Russell, David J.↗