SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cold wall and multibody collision effects on reflection of imploding shock waves using Monte Carlo method and molecular dynamics
A unidirectional fiberglass epoxy compostie specimen is modelled as a homogeneous transversely isotropic continuum plate medium. Acousto-ultrasonic noncontact input-output characterization is studied theoretically with a transmitting and a receiving transducer located on the same face of the plate. The single reflection problem for an incident SV wave at a plane boundary in transversely isotropic medium is analyzed. An obliquely incident SV wave results in a reflected SV wave and a reflected P wave for an angle of incidence of the incident SV wave less than the critical angle. Otherwise, there exists only an SV wave in the medium as the reflected P wave degenerates into a surface wave travelling parallel to the plane boundary. The amplitude ratio of the reflected SV wave is -1 when the angle of incidence is greater than or = the critical angle. The directional dependence of the phase velocity of the SV wave propagating in the transversely isotropic medium has a significant effect on the delay time, as opposed to the directional independence of the phase velocity of a shear wave propagating in an isotropic medium. The displacements associated with the SV wave in the plate and which may be detected by the noncontact receiving transducer are approximated by an asymptotic solution for an infinite transversely isotropic medium subjected to a harmonic point load.
Far infrared reflectance and transmittance as function of wavelength for spacecraft coatings
Randomized problem of diffuse reflection, and radiative transfer in presence of both scattering and absorption
An experimental investigation was conducted to delineate the structure of the flowfield and temperature distributions in a shock wave/turbulent boundary-layer interaction with and without surface cooling. The Mach number upstream was about 3.5, and the wave angle was 23 deg. The wall to stagnation temperature ratio was 0.44 with cooling and 1.1 with heating. A detailed map of the interaction flowfields deduced from numerous boundary-layer traversing stations revealed the influence of wall cooling on the flowfield, wave structure, and size of the flow separation region. With surface cooling, the size of the separation region was much smaller, and the separation and reflected shock waves merged together near the edge of the velocity boundary layer, extending into the freestream as one wave.
Experimental data on the influence of interplanetary perpendicular and oblique shock waves on the ambient energetic protons are presented along with a theoretical analysis of the acceleration of particles in almost perpendicular shock waves. It was found that low-energy protons can be accelerated in perpendicular shock waves by repeated crossings of the shock front up to a maximum energy given by the product of their initial energy times the ratio of the magnetic fields. High-energy protons need to stay at the shock front for longer times than low-energy protons in order to reach the same relative energy gain. In the theoretical study of proton acceleration at almost perpendicular shock waves, it was found that protons reflected at shock waves with the angle between the upstream magnetic field and the shock normal greater than about 80 deg achieve large energy gains at the shock front. The larger this angle, the higher the energy gain. However, the reflection and energization of protons at these shock waves is not 'instantaneous', neither is it a one-step process: it is performed through repeated crossings of the shock front.
Reflection efficiency of soft X-rays by optical flats of Pyrex glass and stainless steel
Fresh evidence that much of the heating in coronal holes is provided by Alfven waves is presented. This evidence comes from examining the reflection of Alfven waves in an isothermal hydrostatic model coronal hole with an open magnetic field. Reflection occurs if the wavelength is as long as the order of the scale height of the Alfven velocity. For Alfven waves with periods of about 5 min, and for realistic density, magnetic field strength, and magnetic field spreading in the model, the waves are reflected back down within the model hole if the coronal temperature is only slightly less than 1.0 x 10 to the 6th K, but are not reflected and escape out the top of the model if the coronal temperature is only slightly greater than 1.0 x 10 to the 6th K. Because the spectrum of Alfven waves in real coronal holes is expected to peak around 5 min and the temperature is observed to be close to 1.0 x 10 to the 6th K, the sensitive temperature dependence of the trapping suggests that the temperature in coronal holes is regulated by heating by the trapped Alfven waves.
We have studied the propagation of inertial Alfvén waves through parallel gradients in the Alfvén speed using the Large Plasma Device at the University of California, Los Angeles. The reflection and transmission of Alfvén waves through inhomogeneities in the background plasma are important for understanding wave propagation, turbulence, and heating in space, laboratory, and astrophysical plasmas. Here we present inertial Alfvén waves under conditions relevant to solar flares and the solar corona. We find that the transmission of the inertial Alfvén waves is reduced as the sharpness of the gradient is increased. Any reflected waves were below the detection limit of our experiment, and reflection cannot account for all of the energy not transmitted through the gradient. Our findings indicate that, for both kinetic and inertial Alfvén waves, the controlling parameter for the transmission of the waves through an Alfvén speed gradient is the ratio of the Alfvén wavelength along the gradient divided by the scale length of the gradient. Furthermore, our results suggest that an as-yet-unidentified damping process occurs in the gradient.
Auroral hiss is observed to propagate over distances comparable to an Earth radius from its source in the auroral oval. The role of Landau damping is investigated for upward propagating auroral hiss. By using a ray tracing code and a simplified model of the distribution function, the effect of Landau damping is calculated for auroral hiss propagation through the environment around the auroral oval. Landau damping is found to be the likely mechanism for explaining some of the one-sided auroral hiss funnels observed by Dynamics Explorer 1. It is also found that Landau damping puts a lower limit on the wavelength of auroral hiss. Poleward of the auroral oval, Landau damping is found in a typical case to limit omega/k(sub parallel) to values of 3.4 x 10(exp 4) km/s or greater, corresponding to resonance energies of 3.2 keV or greater and wavelengths of 2 km or greater. For equatorward propagation, omega/k(sub parallel) is limited to values greater than 6.8 x 10(exp 4) km/s, corresponding to resonance energies greater than 13 keV and wavelengths greater than 3 km. Independent estimates based on measured ratios of the magnetic to electric field intensity also show that omega/k(sub parallel) corresponds to resonance energies greater than 1 keV and wavelengths greater than 1 km. These results lead to the difficulty that upgoing electron beams sufficiently energetic to directly generate auroral hiss of the inferred wavelength are not usually observed. A partial transmission mechanism utilizing density discontinuities oblique to the magnetic field is proposed for converting auroral hiss to wavelengths long enough to avoid damping of the wave over long distances. Numerous reflections of the wave in an upwardly flared density cavity could convert waves to significantly increased wavelengths and resonance velocities.
In view of the difficulties that emerge in numerical simulations of time-dependent phenomena involving MHD waves due to waves' artificial reflection at numerical boundaries, where time-dependent magnetic fields outside those boundaries are unknown, a method previously developed for the determination of radiative boundary conditions is generalized for the treatment of isothermal MHD waves. The illustrative problem thus treated is that of the magnetic braking of a rigidly rotating disk which is embedded in a differentially-rotating fluid. The analytic results obtained are compared with those from numerical simulations with and without the present boundary treatment.
From Intro: In this paper, wer apply the LLW (leaky Lamb Wave) technique to determine the stiffness constants of unnidirectional graphite/epoxy materials...In this paper, we describe a new technique which can be used to determine all five stiffness constants by analyzing the times-of-flight of the recorded reflected acoustic waves in a pulsed LLW experiment.
While the closed-drift Hall thruster (CDT) offers significant improvement in performance over conventional chemical rockets and other advanced propulsion systems such as the arcjet, its potential impact on spacecraft communication signals must be carefully assessed before widespread use of this device can take place. To this end, many of the potentially unique issues that are associated with these thrusters center on its plume plasma characteristics and the its interaction with electromagnetic waves. Although a great deal of experiments have been made in characterizing the electromagnetic interference (EMI) potential of these thrusters, the interpretation of the resulting data is difficult because most of these measurements have been made in vacuum chambers with metal walls which reflect radio waves emanating from the thruster. This project developed a means of assessing the impact of metal vacuum chambers of arbitrary size or shape on EMI experiments, thereby allowing for test results to be interpreted properly. Chamber calibration techniques were developed and initially tested at RIAME using their vacuum chamber. Calibration experiments were to have been made at Tank 5 of NASA GRC and the 6 m by 9 m vacuum chamber at the University of Michigan to test the new procedure, however the subcontract to RIAME was cancelled by NASA memorandum on Feb. 26. 1999.
The formation of soot behind reflected shock waves in argon-diluted mixtures of acetylene, allene, and 1,3-butadiene was investigated by monitoring the attenuation of a laser beam in both the visible (632.8 nm) and the infrared (3.39 microns) regions of the spectrum. The experiments utilized temperatures ranging from 1500-3100 K, reflected shock pressures of 0.3-7.0 bar, and total carbon atom concentrations of 2-20 x 10 to the 17th atoms/cu cm. A bell-shaped dependence of soot yield on temperature was observed during the pyrolysis of all three compounds, which was similar to that previously found for toluene. For acetylene, the decrese in total pressure was found to shift the soot bell to higher temperatures with a significant increase in the maximum soot yield. A computer simulation for acetylene pyrolysis suggested that the reactions between C2H3, C4H3, and C4H4 may be those which lead to the formation of aromatic structures. In addition, it was found that soot is formed much faster and in much larger quantities from allene than from 1,3-butadiene.
The temporal development of sidebands excited near sunrise by two strong HF waves separated by a few hertz is presented. Sidebands are not observed before sunrise when the ionospheric critical frequency is less than the heater frequency. As the ionospheric density increases following sunrise and overdense conditions are established, strong sidebands emerge. Even though these results favor a mechanism which phase modulates the reflected HF wave over one which first downconverts the HF power to ULF before exciting sidebands, it is possible that either mechanism could at times contribute to sideband production.
Quadrature phase detection techniques have been used to monitor the amplitude and phase of a toneburst ultrasonic wave normally reflected from adhesively-bonded steel/rubber interface. The measured phase change values of the reflected signals were found to correlate with variations in sample preparation. It was determined that measured phase shift changes were larger for samples with weaker bonds as manifested by smaller measured values of the applied tensile loads at failure. A model calculation which incorporates the concept of interfacial strength into the usual problem of wave propagation in multi-layered isotropic elastic media was used to deduce a bond-quality parameter from an experimentally measured phase shift.
A theoretical prediction is given of the flow through thick perforated walls of low porosity resulting from the impingement of a moderately strong traveling shock wave. The model was a flat plate positioned normal to the direction of the flow. Holes bored in the plate parallel to the direction of the flow provided nominal hole length-to-diameter ratios of 10:1 and an axial porosity of 25 percent of the flow channel cross section. The flow field behind the reflected shock wave was assumed to behave as a reservoir producing a quasi-steady duct flow through the model. Rayleigh and Fanno duct flow theoretical computations for each of three possible auxiliary wave patterns that can be associated with the transmitted shock (to satisfy contact surface compatibility) were used to provide bounding solutions as an alternative to the more complex influence coefficients method. Qualitative and quantitative behavior was verified in a 1.5- by 2.0-in. helium shock tube. High speed Schlieren photography, piezoelectric pressure-time histories, and electronic-counter wave speed measurements were used to assess the extent of correlation with the theoretical flow models. Reduced data indicated the adequacy of the bounding theory approach to predict wave phenomena and quantitative response.
Proposed reflecting telescope includes large, low-precision primary mirror stage and small, precise correcting mirror. Correcting mirror machined under computer control to compensate for error in primary mirror. Correcting mirror machined by diamond cutting tool. Computer analyzes interferometric measurements of primary mirror to determine shape of surface of correcting mirror needed to compensate for errors in wave front reflected from primary mirror and commands position and movement of cutting tool accordingly.