Search NASA⌕ Search

SEARCH · Search NASA

Results for “actuators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Development and Manufacture of A Proof-of-Concept Magnetically-Geared Actuator for Use in Extremely Cold Lunar Environments

A magnetically-geared actuator is being developed for extremely cold space environments to avoid the wiring and significant efficiency penalty associated with heating grease-lubricated actuators as well as the stringent life and loading constraints imposed by dry film lubricated mechanical gears. This paper describes the lessons learned while designing, manufacturing, and assembling a proof-of-concept prototype similar to the preliminary design of the actuator.

lunar surface↗
NASA NTRS2025

Influence of Actuator Movement Rate During Acquisition of Inlet Characterization Data

This report considers using a process to acquire performance data for supersonic mixed-compression inlets that is faster and less costly than the previous process. In the previous process for acquiring data during wind tunnel experiments, actuators for backpressuring an inlet moved in discrete increments, paused for dynamics to dampen, measured data for 5 s, recorded the data, and then reduced the data to graphic plots of pressure recovery versus mass capture ratio. This discrete data acquisition procedure was methodical, reliable, and accurate. However, acquiring data to characterize the inlet consumed significant wind-on time. Wind tunnel operation was costly when considering maintenance, energy, and human resources (operators and research team); therefore, the price for each data point was high. This report presents a quicker method to obtain all measurements, one which can also be used in blowdown wind tunnels. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. The backpressuring actuator moves continuously, and measurements from high-speed pressure sensors are recorded as the actuator progresses to and past the incremental points. Despite its advantages, the approach raised the following questions: (1) Will the new process be as accurate as the previous process? and (2) Are there any hidden costs? These concerns are addressed in this report. This report reviews a study that was undertaken to compare wind tunnel experiment data taken using the previous discrete data acquisition procedure with data recorded using the dynamic inlet characterization data acquisition procedure. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data for analysis are explained, and a discussion of the results is given. Finally, conclusions from this study that may guide further work in this area are presented.

Inlet Characterization Curves↗
DOE OSTI2024

SELF-HEALING PNEUMATIC ACTUATOR DIAPHRAGMS

In the oil and gas industry, damaged diaphragms in pneumatic actuators can lead to unintended methane leaks, increasing emissions. In this work, replacement self-healing diaphragms are manufactured for a commercial pneumatic actuator. To enable self-healing, hollow microvascular networks are created within the diaphragms using sacrificial 3D printed PLA w/ tin(II) oxalate. These microvascular networks are filled with healing chemistries and, upon damage, rupture. After rupturing, the healing chemistries mix and cure to “heal” the damage and reduce leaks. Separate actuator test stands using nitrogen gas and using natural gas were developed to assess the healing performance of diaphragms. A fatigue stand was also developed to evaluate the effects of the different microvascular network geometries on the fatigue life of diaphragms. Our results demonstrate self-healing in diaphragms subjected to damage and tested for leaks. In fatigue testing, our results indicate that the introduction of microvascular networks does not influence the fatigue life.

Self-healing, pneumatic actuator↗
DOE OSTI2025

Tensile Modeling PVC Gels for Electrohydraulic Actuators

Polyvinyl chloride (PVC)-dibutyl adipate (DBA) gels are a fascinating dielectric elastomer actuator showing promise in soft robotics. When actuated with high voltages, the gel deforms towards the anode. A recent application of PVC gels in electrohydraulic actuators motivates elastic and hyperelastic constitutive relationships for tensile loading modes. PVC gels with plasticizer-to-polymer weight ratios of 2:1, 4:1, 6:1, and 8:1 w/w were evaluated. PVC gels exhibit a linear elastic region up to 25% strain. The elastic modulus decreased with increasing plasticizer content from 288.8 kPa, 56.1 kPa, 24.7 kPa, to 11 kPa. Poisson’s ratio also decreased with increasing plasticizer content from 0.42, 0.43, 0.39, to 0.35. We suggest that the decrease in polymer concentration facilitates a weakly interconnected polymer network susceptible to chain slippage that hinders the network response, thus lowering Poisson’s ratio. Our work suggests that PVC gels can be treated as isotropic and incompressible for large strains and hyperelastic modeling; however, highly plasticized gels tend to act less incompressible at small strains. The power scaling law between the elastic modulus and plasticizer weight ratio showed high agreement, making the elastic modulus deterministic for any plasticizer content. The Neo–Hookean, Mooney–Rivlin, Yeoh, Gent, Ogden, and extended tube hyperelastic constitutive models are investigated. The Yeoh model shows the highest feasibility when evaluated up to 3.5 stretch, showing a maximum normalized root-mean-square-error of 6.85%. Together, these findings establish a constitutive basis for PVC-DBA gels, incorporating small strain elasticity, large strain non-linear behavior, and network analysis while providing suggestive insight into the network structure required for accurately modeling the EPIC.

Polymer Science↗
NASA NTRS1972

Development of a space qualified high reliability rotary actuator for spaceflight use. Volume 2: Appendices to technical report

A space-qualified, high reliability, 150 ft-lb rated torque rotary actuator is described. This drive is an integrated variable reluctance orbit motor-epicyclic transmission actuator. The performance goals were based on future control moment gyrotorquer applications and represent an advancement in the torque-to-weight ratio, backlash, inertia and response characteristics of electric rotary drives. The program accomplishments have been in two areas (1) the development of two high ratio (818:1) actuator configurations (breadboard and flightweight) and (2) the invention of a reliable proximity switch sensor system for self-commutation without use of optical or electrical brush techniques.

Presley, R. W.↗
NASA NTRS1972

Actuator participation in a bending mode identification system

A hydraulic actuator designed for a thrust vector control system used as a shaker for a vehicle to determine the bending mode frequencies is described. The actuator is used as the prime mover and the frequency sensor for the flexible vehicle in a test tower. Advantages in using the actuator piston position with respect to a commanded position to obtain the bending mode frequencies are shown.

Thompson, Z.↗
NASA NTRS1973

Design, fabrication, testing and delivery of a prototype self-locking actuator

The design, fabrication, and testing of a prototype self-locking actuator capable of producing an axial force of 44.5 kN are reported. The actuator passed the initial proof test successfully, however, when the no-load rate test was attempted, the actuator would not extend from the fully contracted position.

Dever, J. E.↗
NASA NTRS1975

Apollo experience report: Guidance and control systems: CSM service propulsion system gimbal actuators

The service propulsion system gimbal actuators of the Apollo command and service module were developed, modified, and qualified between February 1962 and April 1968. The development of these actuators is described as the result of extensive testing, retesting, and modification of the initial design. Successful completion of each mission without anomalies attributable to the actuators indicated that the particular configuration (modification) in use was adequate for the flight profile imposed.

Mcmahon, W. A.↗
NASA NTRS1977

Cost-effective actuator tester

Group of preprogrammed plug-in cards and control module converts breadboard control electronics of actuator assembly to actuator tester. System utilizes electronic control, and hydraulic systems of breadboard actuator into which it is installed.

Kopp, G. F.↗
NASA NTRS1978

Subminiature hydraulic actuator

Subminiature, single-vane rotary actuator for wind-tunnel test-model control-surface actuation systems presents severe torque and system band-pass requirements with stringent space and weight limitations. Actuator has very low leakage of fluid from one side to other, permitting use in precision position servo-systems.

Sevart, F. D.↗
NASA NTRS1980

The Eccentuator: A new concept in actuation

A new concept in actuation for aerospace mechanisms is presented. This actuator, called an 'eccentuator', features unique output characteristics, installation and envelope efficiencies, and relative simplicity. The actuator can be powered by either hydraulic or mechanical inputs. Potential applications of the 'eccentuator' and development efforts are discussed.

Musgrove, R. G.↗
NASA NTRS1979

Formulations and applications of large structure actuator and sensor placements

A new approach based on the steady-state solutions of the optimal control and estimation problems is presented to study respectively the actuator and sensor locations for large flexible structures. A simple and computer-implementable formulation for minimizing the steady state optimal cost function and the state estimation error inherent in the estimation process is given. In conjunction with the new approach, two criteria are established relating the actuator and the sensor placement optimalities respectively to the minimums of the optimal cost function and the state estimation error. To illustrate the concepts of this paper, we present the results of some numerical and analytical studies on the actuator and the sensor locations of several simple flexible beam modes.

Juang, J.-N.↗
NASA NTRS1979

A definition of the degree of controllability - A criterion for actuator placement

The unsolved problem of how to control the attitude and shape of future very large flexible satellite structures represents a challenging problem for modern control theory. One aspect of this problem is the question of how to choose the number and locations throughout the spacecraft of the control system actuators. Starting from basic physical considerations, this paper develops a concept of the degree of controllability of a control system, and then develops numerical methods to generate approximate values of the degree of controllability for any spacecraft. These results offer the control system designer a tool which allows him to rank the effectiveness of alternative actuator distributions, and hence to choose the actuator locations on a rational basis. The degree of controllability is shown to take a particularly simple form when the satellite dynamics equations are in modal form. Examples are provided to illustrate the use of the concept on a simple flexible spacecraft.

C N Viswanathan↗
NASA NTRS1982

Dual drive actuators

A new class of electromechanical actuators is described. These dual drive actuators were developed for the NASA-JPL Galileo Spacecraft. The dual drive actuators are fully redundant and therefore have high inherent reliability. They can be used for a variety of tasks, and they can be fabricated quickly and economically.

Packard, D. T.↗
NASA NTRS1979

Preliminary study, analysis and design for a power switch for digital engine actuators

Innovative control configurations using high temperature switches to operate actuator driving solenoids were studied. The impact on engine control system life cycle costs and reliability of electronic control and (ECU) heat dissipation due to power conditioning and interface drivers were addressed. Various power supply and actuation schemes were investigated, including optical signal transmission and electronics on the actuator, engine driven alternator, and inside the ECU. The use of a switching shunt power conditioner results in the most significant decrease in heat dissipation within the ECU. No overall control system reliability improvement is projected by the use of remote high temperature switches for solenoid drivers.

Beattie, E. C.↗
NASA NTRS1985

Design of a dual fault tolerant space shuttle payload deployment actuator

As the Shuttle Transportation System (STS) becomes operational, the number and variety of payloads will increase. The need to deploy these cargo elements will require a variety of unique actuator designs, all of which will have to conform with STS safety policy. For those missions where payload operations extend beyond the payload bay door envelope, this policy deems the prevention of door closure as a catastrophic hazard. As such, it must be controlled by independent, primary and backup methods. The combination of these methods must be two fault tolerant. The design of such an actuator is described. The device consists of a single linear ballscrew with two ballnuts, each bellnut forming an independent actuator using the common ballscrew. The design requirements, concept development, hardware configuration, and fault tolerance rationale are highlighted.

Teske, D. R.↗
NASA NTRS1985

Intelligent redundant actuation system requirements and preliminary system design

Several redundant actuation system configurations were designed and demonstrated to satisfy the stringent operational requirements of advanced flight control systems. However, this has been accomplished largely through brute force hardware redundancy, resulting in significantly increased computational requirements on the flight control computers which perform the failure analysis and reconfiguration management. Modern technology now provides powerful, low-cost microprocessors which are effective in performing failure isolation and configuration management at the local actuator level. One such concept, called an Intelligent Redundant Actuation System (IRAS), significantly reduces the flight control computer requirements and performs the local tasks more comprehensively than previously feasible. The requirements and preliminary design of an experimental laboratory system capable of demonstrating the concept and sufficiently flexible to explore a variety of configurations are discussed.

Defeo, P.↗
NASA NTRS1985

A design technique for determining actuator gains in spacecraft vibration control

A design procedure is described which determines the gains of a diagonal damping matrix to control the vibrations of a flexible structure with application to orbiting spacecraft. The procedure is based on minimizing the energy dissipated by control actuators using nonlinear mathematical programming. Each damping gain is assumed to be an active viscous damper and the design process is formulated so that the force or torque output of the actuator does not exceed a specified value. The response of the structure at some specified time after the termination of the disturbance is constrained to be less than some prescribed value based upon spacecraft mission performance requirements. A grillage example is used to demonstrate the design process for determining gains for two representative cases. Resulting designs are verified by a finite element analysis of the structure augmented by the control actuators.

Horner, G. C.↗