SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Procedures are presented for obtaining valid frequency-domain transfer functions of regulated reactor energy-storage dc-to-dc converters. These procedures are for measuring loop gain, closed loop gain, output impedance, and audio susceptibility. The applications of these measurements are discussed.
A technique to control a rim suspended in a magnetic field was developed. A complete system was developed, incorporating a support structure, magnetic actuators, a rim drive mechanism, an emergency fail-safe system, servo control system, and control electronics. Open loop and closed loop response of the system at zero speed and at 500 revolutions per minute (r/min) of the rim was obtained and analyzed. The rim was then dynamically balanced and a rim speed of 725 r/min was achieved. An analog simulation of the hardware was developed and tested with the actual control electronics connected to the analog computer. The system under development is stable at rim speeds below 700 r/min. Test results indicate that the rim under test is not rigid. The rim has a warp and a number of binding modes which prevented achievement of higher speeds. Further development efforts are required to achieve higher rim speeds.
Techniques appropriate for implementation onboard the space telescope and other spacecraft to manage the accumulation of momentum in reaction wheel control systems using magnetic torquing coils are described. Generalized analytical equations are derived for momentum control laws that command the magnetic torquers. These control laws naturally fall into two main categories according to the methods used for updating the magnetic dipole command: closed loop, in which the update is based on current measurements to achieve a desired torque instantaneously, and open-loop, in which the update is based on predicted information to achieve a desired momentum at the end of a period of time. Physical interpretations of control laws in general and of the Space Telescope cross product and minimum energy control laws in particular are presented, and their merits and drawbacks are discussed. A technique for retaining the advantages of both the open-loop and the closed-loop control laws is introduced. Simulation results are presented to compare the performance of these control laws in the Space Telescope environment.
The situation in which an operator is faced with a continuous control task plus one or more discrete information processing tasks is discussed. A modelling approach which has the capability of realistically representing both types of tasks and the resulting interactions is sought. The modelling approach utilizes discrete network models for the cognitive tasks and elements of an open-loop - closed-loop control representation for the continuous task. the approach is demonstrated through its application to a simulated Digital Avionics Information System in which subjects were required to perform retrieval and processing tasks as well as flight control. This model differs from conventional model in that system status sampling is not necessarily continuous or periodic. Rather, the pilot is assumed to read system status displays only as time permits and operate in a so-called open-loop preprogrammed fashion between sampling.
A simple algebraic solution is obtained to an optimal control problem in joint space for a general robotic manipulator. Open loop and closed loop control laws are obtained. The resulting control algorithm is similar in form to a commonly used heuristic controller using cubic polynomial trajectories.
The requirements, design, and expected performance of the Attitude Control Subsystem for the spin-stabilized Extreme Ultraviolet Explorer Satellite are presented. In the sky-mapping phase, closed-loop magnetic control keeps the spin axis pointed toward the sun. In the spectroscopy phase, the attitude control loop is closed via the ground. The satellite's attitude and spin rate are determined using periodically downlinked star data. An attitude control algorithm generates commands to be uplinked to the satellite for spin axis precession and spin rate control. Computer simulations of the satellite dynamic response, pointing error, and stability during spin axis precession are presented, and parameters that affect the pointing performance are evaluated.
The capability of the satellite to perform a variety of space operations to be accomplished from the shuttle is reviewed considering use of the satellite with man-in-loop and closed loop modes and deployment (toward or away from Earth, up to 100 km), stationkeeping, retrieval and control of the satellite. Scientific payloads are to be used to perform experiments and scientific investigation for applications such as magnetometry, electrodynamics, atmospheric science, chemical release, communications, plasmaphysics, dynamic environment, and power and thrust generation. The TSS-S will be reused for at least 3 missions after reconfiguration and refurbishment by changing the peculiar mission items such as thermal control, fixed boom for experiments, aerodynamic tail for yaw attitude control, external skin, experiments, and any other feature. The TSS-S is to be composed of three modules in order to allow independent integration of a single module and to facilitate the refurbishment and reconfiguration between flights. The three modules are service, auxiliary propulsion, and payload modules.
This paper discusses the use of eigenspace techniques for the design of an active flutter control/gust load alleviation system for a hypothetical research drone. One leading edge and two trailing edge aerodynamic surfaces are available for control. Full state control laws are designed for two combinations of control surfaces by selecting feedback gains which place closed loop eigenvalues and shape closed loop eigenvectors so as to stabilize wing flutter and reduce gust loads at the wing root while yielding acceptable robustness and satisfying constraints on rms control surface activity. These controllers are realized by state estimators designed using an eigenvalue placement/eigenvector shaping technique which results in recovery of the loop transfer characteristics of the full state feedback systems. The resulting feedback compensators are shown to perform almost as well as the full state designs. They also exhibit acceptable performance in situations in which the failure of an actuator is simulated.
The use of eigenspace techniques for the design of an active flutter suppression system for a hypothetical research drone is discussed. One leading edge and two trailing edge aerodynamic control surfaces and four sensors (accelerometers) are available for each wing. Full state control laws are designed by selecting feedback gains which place closed loop eigenvalues and shape closed loop eigenvectors so as to stabilize wing flutter and reduce gust loads at the wing root while yielding accepatable robustness and satisfying constrains on rms control surface activity. These controllers are realized by state estimators designed using an eigenvalue placement/eigenvector shaping technique which results in recovery of the full state loop transfer characteristics. The resulting feedback compensators are shown to perform almost as well as the full state designs. They also exhibit acceptable performance in situations in which the failure of an actuator is simulated.
In this study, the vibration control of large space structures using the linear quadratic regulator technique is investigated. Emphasis is made on the control of both optimally designed structures and also the original (uniform) structures using the cantilever beam as an example. The open loop and closed loop eigenvalues are compared and the transient responses are obtained to determine the effectiveness of the control system design.
The Mobile Satellite Experiment (MSAT-X) phased array antenna is being modified to meet future requirements. The proposed system consists of two high gain antennas mounted on each side of a fuselage, and a low gain antenna mounted on top of the fuselage. Each antenna is an electronically steered phased array based on the design of the MSAT-X antenna. A beamforming network is connected to the array elements via coaxial cables. It is essential that the proposed antenna system be able to provide an adequate communication link over the required space coverage, which is 360 degrees in azimuth and from 20 degrees below the horizon to the zenith in elevation. Alternative design concepts are suggested. Both open loop and closed loop backup capabilities are discussed. Typical antenna performance data are also included.
In this study the vibration control of large space structures with structural damping is investigated. Emphasis is made on the control of both a class of optimally designed (stepped) structures and also the corresponding uniform structures using a cantilever beam as an example. The open loop and closed loop dynamics are compared and the transient responses are determined to study the effect of damping on the control system design.
A neighboring optimal guidance scheme was devised for a nonlinear dynamic system with stochastic inputs and perfect measurements as applicable to fuel optimal control of an aeroassisted orbital transfer vehicle. For the deterministic nonlinear dynamic system describing the atmospheric maneuver, a nominal trajectory was determined. Then, a neighboring, optimal guidance scheme was obtained for open loop and closed loop control configurations. Taking modelling uncertainties into account, a linear, stochastic, neighboring optimal guidance scheme was devised. Finally, the optimal trajectory was approximated as the sum of the deterministic nominal trajectory and the stochastic neighboring optimal solution. Numerical results are presented for a typical vehicle. A fuel-optimal control problem in aeroassisted noncoplanar orbital transfer is also addressed. The equations of motion for the atmospheric maneuver are nonlinear and the optimal (nominal) trajectory and control are obtained. In order to follow the nominal trajectory under actual conditions, a neighboring optimum guidance scheme is designed using linear quadratic regulator theory for onboard real-time implementation. One of the state variables is used as the independent variable in reference to the time. The weighting matrices in the performance index are chosen by a combination of a heuristic method and an optimal modal approach. The necessary feedback control law is obtained in order to minimize the deviations from the nominal conditions.
In this study, the vibration and orientation control of large space structures using the linear quadratic regulator technique is investigated. Emphasis is placed on the control of both a class of optimally designed structures and uniform structures meeting the mission requirements using a long free-free beam in orbit as an example. The open loop and closed loop dynamics are compared and the transient responses are obtained to determine the effectiveness of the control system design.
MARSYAS is a computer aided control system design package for the simulation and analysis of open loop and closed loop dynamic systems. Outlined here is the numerical and theoretical basis of the MARSYAS functions developed during the summer of 1991. In particular, the numerical computation of the matrix exponential e(exp A) = I + A + A(exp 2)/2! + A(exp 3)/3! + ... and the numerical computation of the finite system zeros of a dynamic system (continuous time or discrete time) are presented.
The validation tests conducted on the Control/Structures Interaction (CSI) Computer System (CCS)/Remote Interface Unit (RIU) is discussed. The CCS/RIU consists of a commercially available, Langley Research Center (LaRC) programmed, space flight qualified computer and a flight data acquisition and filtering computer, developed at LaRC. The tests were performed in the Space Structures Research Laboratory (SSRL) and included open loop excitation, closed loop control, safing, RIU digital filtering, and RIU stand alone testing with the CSI Evolutionary Model (CEM) Phase-0 testbed. The test results indicated that the CCS/RIU system is comparable to ground based systems in performing real-time control-structure experiments.
This paper deals with the control of three dimensional rotational maneuvers of flexible spacecraft. A spacecraft with a spherical hub and six symmetric appendages is considered here as a model. The appendages are long and flexible leading to low frequency vibration under any control action. To provide a comprehensive treatment of input shaped controllers, both open loop and closed loop controllers are considered. The minimum-time bang-bang and the near-minimum-time controller, used in conjunction with the shaped input technique are studied. In addition, a combination of a Liapunov controller with the shaped input control technique is proposed to take advantage of the simple feedback control strategy and augment it with a technique that can eliminate the vibratory motion of the flexible appendages more efficiently.
The major contributions of the grant effort have been the enhancement of the Compensator Improvement Program (CIP), which resulted in the Ohio University CIP (OUCIP) package, and the development of the Model and Data-Oriented Computer Aided Design System (MADCADS). Incorporation of direct z-domain designs into CIP was tested and determined to be numerically ill-conditioned for the type of lightly damped problems for which the development was intended. Therefore, it was decided to pursue the development of z-plane designs in the w-plane, and to make this conversion transparent to the user. The analytical development needed for this feature, as well as that needed for including compensator damping ratios and DC gain specifications, closed loop stability requirements, and closed loop disturbance rejection specifications into OUCIP are all contained in Section 3. OUCIP was successfully tested with several example systems to verify proper operation of existing and new features. The extension of the CIP philosophy and algorithmic approach to handle modern multivariable controller design criteria was implemented and tested. Several new algorithms for implementing the search approach to modern multivariable control system design were developed and tested. This analytical development, most of which was incorporated into the MADCADS software package, is described in Section 4, which also includes results of the application of MADCADS to the MSFC ACES facility and the Hubble Space Telescope.