Search NASA⌕ Search

SEARCH · Search NASA

Results for “conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Three-dimensional modeling and simulations of single-crystal and bi-crystal titanium for high-strain-rate loading conditions

High purity single crystal titanium (Ti) under shock wave loading is modeled under both one-dimensional and three-dimensional cylindrical conditions. Cylinder sizes of 10 μm and 20 μm radius are both considered in order to assess influence of boundary conditions. A thermodynamically consistent single crystal model for application to shock conditions is presented. The model accounts for the coupled non-linear elastic, dislocation slip, deformation twinning, and structural phase transformation response of the titanium material. Plate impact experiment results using a copper flyer are used to compare against the simulations for crystals oriented in [0001] and [10$\overline1$1] crystallographic directions. The one-dimensional and threedimensional simulations of the two differently oriented single crystals indicate differences between the one-dimensional and three-dimensional representation, especially for the [10$\overline1$1] oriented single crystal. This orientation breaks the relative orientation symmetry between the crystal and cylinder which otherwise exists for the [0001] oriented single crystal. A significant amount of heterogeneity in the field response of the[10$\overline1$1] oriented simulation was demonstrated due to the highly coupled nature of the deformation. A bi-crystal model composed of both the [0001] and [10$\overline1$1] orientations with the boundary between the two along the axis of the cylinder is also considered for a cylinder model size of 10 μm. The results indicate a strong interaction between the two grains that affects the ω phase volume fraction achieved relative to the single crystal calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tracking the phase changes in micelle-based NiGa nanocatalysts for methanol synthesis under activation and working conditions

The hydrogenation of CO 2 into high energy density fuels such as methanol, where the required H 2 is obtained from renewable sources, is of utmost importance for a sustainable society. In recent years, NiGa alloys have attracted attention as promising catalyst material systems for the hydrogenation of CO 2 into methanol at ambient pressures. They thus represent an energy-saving alternative to the Cu-based catalysts employed in today's catalytic industry that require high pressures for the CO 2 hydrogenation. However, the underlying reaction mechanisms for the NiGa system are still under debate. One of the challenges here is to unravel the evolution and coexistence of the different species in the heterogeneous NiGa catalyst system under activation and reaction conditions. To shed light on their evolution under activation in H 2 and their catalytic roles under CO 2 hydrogenation working conditions on well-defined Ni 3 Ga 1 and Ni 5 Ga 3 nanoparticle (NP) catalysts, we employed a multi-probe approach in this study. It included advanced machine learning-based analysis of operando X-ray absorption spectroscopy data combined with operando powder X-ray diffraction and near ambient pressure X-ray photoelectron spectroscopy measurements, as well as reactivity studies using bed-packed mass flow reactors. In addition, we employed atomic force microscopy and scanning transmission electron microscopy for structural characterization. Under H 2 activation at 1 bar total pressure, we concluded the formation of metallic Ni, starting for Ni 3 Ga 1 at 300 °C, and for Ni 5 Ga 3 at 400 °C. At higher temperatures, the formation of NiGa alloys follows. The α'-Ni 3 Ga 1 alloy phase is predominantly formed for the Ni 3 Ga 1 NPs, while the coexistence of α'-Ni 3 Ga 1 , δ-Ni 5 Ga 3 and Ga 2 O 3 phases is observed for the Ni 5 Ga 3 NPs after the H 2 activation. The formation of the Ga 2 O 3 phase also results in the presence of excess metallic Ni. Under CO 2 hydrogenation reaction conditions, Ga partially oxidizes again to form a Ga 2 O 3 -rich particle shell for both NP compositions, yet, to a larger extent for the Ni 3 Ga 1 NPs, which, in turn, feature a higher amount of excess Ni. We reveal that metallic Ni is responsible for the high selectivity of the Ni 3 Ga 1 NPs towards the production of methane in our catalytic tests. In contrast, the Ni 5 Ga 3 NPs display a strong selectivity toward methanol production (>92%), more than one order of magnitude higher than that for the Ni 3 Ga 1 NPs, which we ascribe to the presence of the δ-Ni 5 Ga 3 phase.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Super-time-stepping schemes for parabolic equations with boundary conditions

In this work, we present a super-time-stepping scheme for numerically solving parabolic partial differential equations with Dirichlet boundary conditions (BC). Using the general Forward Euler scheme, one can show that by taking varying step sizes there is the potential of propagating the solution forward in time by a greater amount than with uniform step sizes, while maintaining the same order of accuracy. As shown in previous works, if one further requires that the scheme have the Convex Monotone Property (CMP), then there exists a scheme which results in linear, monotone stability of the solution. This monotone stability is highly desirable in many physical situations, such as thermal diffusion, where the physical system will not oscillate, but will behave monotonically. However, the schemes devised in previous works do not include situations that have a boundary condition, and the inclusion of boundary conditions will henceforth be our focus. It is shown that a particular Runge-Kutta-Gegenbauer class of schemes [5] will maintain the CMP even in the presence of Dirichlet BC.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Data-driven prediction of geometry- and toolpath sequence-dependent intra-layer process conditions variations in laser powder bed fusion

Geometrical features and toolpath sequence are two important factors that cause process condition variations, such as variations in the meltpool temperature or meltpool size, that might lead to undesired material properties in the laser powder bed fusion (LPBF) process. Due to the high dynamics and complex physics of the LPBF process, it is difficult to predict variations in process conditions with simulations alone. Advances in measurement technology and computational technologies open up new possibilities for smart manufacturing. In this paper, a data-driven method to predict intra-layer variations in the processing conditions that source from the toolpath sequence and part geometry is presented. The approach is demonstrated using two-color on-axis pyrometer measurements. Three demonstration cases are presented in which it is demonstrated (1) how the trained predictive model can be used as a filter to ease the interpretation of process variations and discover patterns related to toolpath and part geometry, and (2) how to generate predictions that can be used for feedforward control, i.e., for adjusting laser power or scanning speed along the toolpath using a meltpool temperature prediction model generated based on on-axis measurements. Results show that the developed prediction model is able to meaningfully predict process variations resulted from toolpath sequence and geometry. Predictions are aligned with the results from the related work of others and for the case of 180° laser path turnarounds in our high-speed X-ray imaging experiments. In conclusion, the potential issues related to the current maturity status of the process and measuring equipment that could in practice affect the performance of the proposed solutions are also discussed.

42 ENGINEERING↗
DOE OSTI2022

Dynamics of deuterium retention and desorption from plasma-facing materials in fusion reactor-relevant conditions

Hydrogen isotopes retention and desorption during and after discharges in fusion devices are still not well understood due to the complex device conditions and limitations of in-situ diagnostics and measurements. Here, we simulated well-diagnosed recent experiments at the DIII-D facility to benchmark our ITMC-DYN integrated package of modeling deuterium diffusion, retention, and desorption during and after D discharge irradiation. Modeling results were compared with detail experimental data of D desorption fluxes for various irradiation conditions. We predicted the temporal evolution of free and trapped D distribution in tungsten (W) plasma-facing material (PFM). Effects of key parameters namely diffusion coefficient, recombination rate, trapping energies against different defect types, were examined in these simulations. Existing experimental data of these parameters in literature varies significantly which makes it harder to identify key mechanisms and physics responsible for hydrogen isotope retention and desorption. The purpose of this work is to accurately simulate recent well-diagnosed reactor experiments given the uncertainties in such parameters and identify mechanisms responsible for the retention and desorption. We implemented the best identified diffusion, recombination, and trapping parameters in ITMC-DYN package that integrate both various collisional and thermal processes. We predicted, for example, that sample cooling between discharges in DIII-D operations can significantly affect the spatial distribution of trapped D in W under reactor irradiation conditions. Correct prediction of desorption spectra from samples irradiated during 10 DIII-D discharges showed that up to 35% of D can be retained in high binding energy defects such as vacancy clusters or voids.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Verification of Bison fission product species conservation under TRISO reactor conditions

When assessing the reliability and predictive capabilities of a simulation tool, code verification is used to ensure that the implemented numerical algorithm is a faithful representation of its underlying mathematical model, including partial differential or integral equations, initial and boundary conditions, and auxiliary relationships. During this process, numerical results in a discrete solution are compared to the analytical solution of the mathematical model. Here, in this paper, the code verification process is applied to one-dimensional spatiotemporal problems that exercise partial differential equation governing the conservation of fission product species (or mass diffusion). Numerical experiments were performed in the Bison fuel performance code to evaluate its predictive capability under various TRISO reactor conditions such as base irradiation and safety heating test conditions for either short- or long-lived fission product species, as well as a case concerning evaporation from the outer surface of a particle. The code predictions were compared with the expected exact results obtained from the analytical expressions, and the fact that they demonstrate the correct analytical behavior provides strong evidence of proper numerical algorithm implementation.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2026

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Enhancing the mass resolving power of FRIB’s proposed high-voltage MR-ToF mass separator and spectrometer: Addressing non-ideal conditions

Multi-reflection time-of-flight mass separators and spectrometers (MR-ToF MSs) are indispensable tools at radioactive ion beam (RIB) facilities. These electrostatic ion beam traps act as highly selective mass separators and high-precision mass spectrometers for rare and exotic nuclei. When well-tuned and designed to minimize higher-order flight-time aberrations, state-of-the-art MR-ToF MSs approach, and slightly exceed, mass resolving powers of m/Δm = 10 6 . Achieving m/Δm ≥ 3 ⋅ 10 6 would provide the ability to resolve > 90 % of all known isomeric states with half-lives above 10 ms. However, the ability to mass separate in all practical setups is limited by non-ideal conditions which place such resolving powers out of reach. Here, to this end, we present a simulated analysis of these conditions in the newly proposed high-voltage MR-ToF MS for the Facility for Rare Isotope Beams (FRIB). It is expected to store ions at 30 keV beam energy and increase ion throughput by two orders of magnitude compared to current devices. Existing efforts to mitigate the effects of non-ideal conditions employed for current MR-ToF devices storing ions at < 3 keV beam energy will already enable mass resolving powers approaching 10 6 for FRIB’s high-voltage MR-ToF device. Simulations of newly proposed mitigation strategies show that even mass resolving powers approaching 10 7 might become feasible.

Electrostatic ion beam traps↗
DOE OSTI2025

Addressing the impact of Lyman opacity in inference of divertor plasma conditions with 2D spectroscopic camera analysis of Balmer emission during detachment in JET L-mode plasmas

The impact of re-absorption of the deuterium Lyman series emission was addressed in inferring divertor plasma conditions from Balmer series emission with 2D spectroscopic camera analysis during detachment in JET L-mode plasmas. The previously presented methodology was amended by modifying the standard photon emission coefficients and ionization and recombination rate coefficients of the ADAS database to consider the re-population of excited states due to Lyman opacity. This resulted in the estimate for the atomic density near the outer strike point to decrease by up to 75% at the onset of detachment at strike point temperatures of T e,osp ≈ 1.0–3.0 eV with respect to the strongly overestimated previously obtained values, whereas the estimated electron temperature and density were unaffected by the opacity correction within the scatter of the data and only a moderate reduction by up to 20% was observed in the estimate for the molecularly induced fraction of the Balmer emission. No noticeable change was seen in the ionization rate, calculated from the estimated outer strike point conditions, due to the decrease in the atomic density estimate compensating for the increased values of the opacity-corrected ADAS rate coefficients for ionization. In detached conditions at T e,osp ≈ 0.5–1.0 eV, 25%–35% lower recombination rates were provided by the opacity-corrected model. The observed effects on the experimental analysis were supported by a corresponding synthetic analysis based on EDGE2D-EIRENE simulations.

Balmer emission↗
DOE OSTI2020

Experimental study for critical heat flux in 2x2 rod bundles at high pressure conditions

Critical heat flux (CHF) phenomena has been a topic of study for over fifty years yet remains a serious concern across industries and especially in water-cooled nuclear reactor design. CHF data in the high-pressure range is limited, and the effects of bundle geometry and non-uniform heat flux profile are challenging to quantify. In this study, CHF experiments were performed in upward flowing water in a 2 × 2 rod bundle with a cosine profile heat flux. Data were collected between 16.5 and 18 MPa at two mass flux conditions with three inlet subcooling conditions. Under these conditions, average CHF was shown to decrease with increasing pressure. However, pressure had less of an effect than decreasing the inlet subcooling or the mass flux, both of which reduce the CHF value considerably. Of interest, correlations that have been developed for lower pressure continued to predict CHF occurrences with moderate accuracy outside their ranges of validity. Nearly all predicted values were within 20% of experimental values.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Wrought FeCrAl alloy (C26M) cladding behavior and burst under simulated loss-of-coolant accident conditions

Cladding burst experiments for FeCrAl cladding were performed in the Severe Accident Test Station facility at Oak Ridge National Laboratory. These experiments were simulated using the BISON fuel performance code to better understand the cladding plastic behavior and failure under simulated loss-of-coolant accident conditions. 3D cladding surface boundary conditions were generated using composite axial and azimuthal profiles from experiment thermocouple data. To improve the simulation analysis capabilities in BISON for cladding burst behavior, new thermal creep, plasticity, and failure stress models specific to C26M, a wrought FeCrAl alloy, were developed and implemented. Initial cladding burst results indicated a general underprediction in the failure temperature of the six cladding burst simulations versus the observed failure temperatures. Close investigation of the experiment timing versus the underlying tensile test data revealed that, compared with the tensile specimens, the cladding tubes did not experience the same long holding time at high temperatures. New tensile tests were performed at high temperatures using a temperature ramp similar to the simulated loss-of-coolant accident experiments. These new tensile curves showed an approximately 80% increase in the ultimate tensile strength of the C26M alloy, indicating that a holding time of 10 min at 700 °C and 800 °C allows annealing to change the material microstructure. Using the updated tensile properties, the burst temperatures and stresses from the simulations showed remarkable agreement with the experimental results. This study was then extended by varying the initial pressure to highlight the burst temperature difference between standard Zircaloy-4 and C26M cladding under equivalent conditions. The results show that C26M has a burst temperature that is approximately 70–130 K greater than that of Zircaloy-4. In conclusion, these modeling predictions can be further improved by collecting high-temperature tensile data for C26M beyond the temperature ranges used in this work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

3D probabilistic fracture mechanics / computational fluid dynamics simulation of a reactor pressure vessel under transient conditions

Reactor pressure vessels (RPVs) are safety-critical light-water-reactor components that, under irradiation, experience long-term material degradation in the form of embrittlement. This can increase their susceptibility to fracture under thermal-shock conditions, which could occur during off-normal transients such as loss-of-coolant accidents (LOCAs). During a LOCA, the most severe conditions for the RPV occur when emergency core cooling water is injected through the cold legs into the water-and-steam-filled RPV. The rapid cooling of the downcomer and internal RPV surface causes decreased temperature and elevated thermally driven tensile stresses in the RPV wall. This, combined with long-term material embrittlement, may cause fracture initiation at pre-existing flaws, challenging the integrity of the RPV. Assessing RPV integrity during transients with a large spatial variation in the coolant temperature requires a modeling approach that considers the effects of spatially varying coolant temperature on the fracture probability of a population of flaws distributed throughout the RPV, accounting for spatially varying embrittlement. Here, the present study addresses this need by demonstrating first-of-its-kind coupling of a high-fidelity 3D computational fluid dynamics code with 3D probabilistic fracture mechanics This was accomplished using representative models of a pressurized-water reactor subjected to small- and medium-break LOCA conditions, both of which can result in large spatial temperature variations. While the observed impact of accounting for 3D effects was minimal under the small-break LOCA this study indicates a significant increase in the probability of fracture initiation under the medium-break LOCA when 3D effects are considered, relative to a spatially uniform cooling scenario.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Frictional Contacts Between Individual Woody Biomass Particles under Wet and Dry Conditions

Friction between wood particles can be a critical property when designing processing equipment for creating cellulosic biofuels and similar natural products. Also, as wood processing is likely to occur year-round, understanding the friction between wet as well as dry wood particles can help design and model equipment, such as screw feeders. Here, a tribo-rheometry method was developed using a commercial rheometer that measured the torque required to rotate two contacting millimeter-scale wood chip particles. First, a range of normal forces were used to find the limits of the experimental method. Torque values were measured for seven pairs of wood chip particles at 1 N normal force under both dry and wet conditions, at both ambient conditions and in a humidity-controlled chamber. The torque required to rotate the wet particles was consistently higher than that of the dry particles, although differences were not quite statistically significant when measurements were performed at ambient conditions. Using humidity control resulted in torque values for wet particles of 1900 uNm and 900 uNm for dry particles. Finally, the friction coefficient was calculated as 0.23 for wet particles and 0.11 for dry particles when humidity was controlled. These frictions coefficients agreed with values for wood reported in the literature. Overall, controlling humidity is strongly recommended to quantify the range of friction for particles that uptake water, including granular systems from biomass to food to powders.

biomass↗
DOE OSTI2020

Experimental and modeling study of C2–C4 alcohol autoignition at intermediate temperature conditions

C2–C4 alcohols are advantageous blendstocks identified by many research groups, including the U.S. Department of Energy Co-Optima Initiative, towards enabling efficient, boosted Spark-Ignition (SI) engines. Their use in advanced engine applications requires a comprehensive understanding of their intermediate-temperature autoignition behavior. This work reports an experimental and modeling study covering their fundamental autoignition characteristics in a twin-piston rapid compression machine at pressures of 20 and 40 bar, intermediate temperatures from 750 to 980 K, and two fuel loading conditions representative of boosted SI engines. Direct comparison between these alcohols is made, where the order of reactivity is established across different thermodynamic and fuel loading conditions. Changes in preliminary exothermicity (or intermediate-temperature heat release) displayed in single-stage autoignition across different alcohols and conditions are also quantified. This provides insight into fuel-to-fuel differences, and how these could affect advanced combustion concepts such as spark-assisted compression ignition. Kinetic models are used to simulate the experiments, and reasonable agreement is obtained. Furthermore, the sensitivity analysis results demonstrate the importance of accurately capturing the autoignition kinetics, particularly H-abstraction reactions on the parent fuels by OH and HO 2 , and the branching ratio associated with these.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Is satellite Sun-Induced Chlorophyll Fluorescence more indicative than vegetation indices under drought condition?

Droughts represent one of the most severe abiotic stress factors that could result in great crop yield loss. Numerous vegetation indices have been proposed for monitoring the vegetation condition under stress and assessing drought impacts on yield loss. However, the understanding and comparison between traditional vegetation indices (VIs) and the newly emerging satellite Sun-Induced Chlorophyll Fluorescence (SIF) for monitoring vegetation condition is still limited especially under drought stress and at multiple spatial scales. In this study, the potential of satellite observation SIF for monitoring corn response to drought was investigated based on the 2012 drought in the US Corn Belt. The standardized precipitation evapotranspiration index (SPEI) was used here to quantify drought. We found that all SPEI were above –1, except for July (–1.27), August (–1.39) and September (–1.14) in 2012, indicating the severity of this drought. We examined the relationship between satellite measurements of SIF, SIF yield , VIs (e.g., NDVI and EVI) and SPEI. Results indicated that SIF yield was sensitive to drought and SIF captured the stress more accurately both at the regional and state scales for the US Corn Belt. Quantitatively, SIF yield had a high correlation with SPEI (r = 0.987, p < 0.05) over the entire Corn Belt, and it indicated losses in response to drought approximately one month earlier than SIF/NDVI/EVI. Furthermore, our results demonstrated that SIF could be trusted as an effective indicator to study the relationship between GPP (R 2 ≥ 0.8664, p < 0.01) under drought conditions across the Corn Belt. Finally, this study highlighted the advantage of using satellite SIF observations to monitor the drought stress on crop growth especially GPP at regional scale.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Optimal conditions for efficient flow-electrode capacitive deionization

One of the current barriers to achieving fast and stable performance for flow-electrode capacitive deionization (FCDI) is determining optimal operating parameters. To date, however, no consensus has been reached for universal conditions for FCDI. Through experimental and modeling approaches in this study, we systematically evaluated the influence of applied potential (V = 1.2–2.4 V) and electrolyte concentration (C0 = 0.05–0.5 M) on the FCDI and electrodialysis (ED) desalination processes. Evaluation indicators include the concentration decrease in the desalinated solution, salt removal rates, pH fluctuations, charge efficiency, and energy consumption. Results demonstrated that the dynamic curves of concentration decrease at 2.0 V nearly overlapped with the response at 1.6 V at certain electrolyte concentrations, while the salt removal rates at 0.2 M salt concentration were the best among all concentrations tested at a range of applied potential. Therefore, it was thus concluded that the optimum conditions for FCDI operation are 1.6 V applied potential and 0.2 M initial salt concentration, under which faradaic reactions are not being triggered, and concentration polarization does not significantly affect ion transfer. Furthermore, a comparative study between FCDI and ED indicated that ED has a different dependence on the electrolyte concentration and applied potential, in which the desalination can be linearly enhanced with increasing potential but greatly limited at high concentrations. Due to the presence of carbon particles in FCDI, the enhanced charge/ion transfer is probably the main reason for the different desalination performance of FCDI and ED. Overall, the optimal operating parameters obtained in this work could be used as basic test conditions for further development of new carbon-based materials for FCDI.

42 ENGINEERING↗
DOE OSTI2020

Antecedent conditions determine the biogeochemical response of coastal soils to seawater exposure

Coastal landscapes are increasingly exposed to seawater due to sea level rise and extreme weather events. The biogeochemical responses of these vulnerable ecosystems are poorly understood, limiting our ability to predict how their role in local and global biogeochemical cycles will shift under future conditions. Here we evaluate how antecedent conditions influence the biogeochemical response of soil to seawater inundation events based on a 42-day laboratory incubation experiment with soils collected from a natural salinity gradient across a coastal floodplain. We quantified influences of seawater inundation on intact soil cores through high-frequency carbon dioxide (CO 2 ) and methane (CH 4 ) gas fluxes measurements as well as ultrahigh resolution characterization of organic matter chemistry and metabolites. Mean CO 2 and CH 4 fluxes were higher after inundation compared to control cores for soils that had low in situ salinity. Soils with low in situ salinity also exhibited significant shifts in organic matter profiles after inundation, with surficial soils (0-7.5 cm) becoming more enriched in phenolic compounds, compared to deeper soils (7.5-15 cm). The number of biochemical transformations inferred from mass spectrometry increased significantly after inundation for soils with low in situ salinity, and a trend of decreasing thermodynamic favorability with increasing salinity was observed, suggesting an increase in microbial activity following inundation. Our results suggest that seawater inundation of low-salinity terrestrial environments can lead to increased microbial activity, preferential depletion of more thermodynamically favorable compounds, and increased soil carbon release. Finally, we conclude that the biogeochemical impacts of future seawater exposure will be modulated by antecedent conditions associated with landscape position within coastal watersheds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Wear Performance of incoloy 800HT and inconel 617 in various surface conditions for high-temperature gas-cooled reactor components

Incoloy™ 800HT and Inconel™ 617 are primary candidate structural materials for high-temperature gas-cooled reactors (HTGRs). Impurities (e.g., H 2 O, CH 4 ) in the coolant induce corrosion reactions that affect tribological behavior. We investigate the high-temperature tribological performance of the alloys under surface conditions including: conditioned in H 2 O-containing helium at elevated temperatures, hardened via the carbon-diffusion Kolsterising® treatment, and conditioned after hardening. Initial friction coefficients and volume removed serve as metrics for wear performance. In this work, we find that wear mechanisms including scuffing, glaze-oxide formation, and oxide-layer wear and break-through are governed by surface hardness, chemistry, and applied load. The formation of a glaze-oxide layer is achieved with an oxide of sufficient mechanical integrity if the oxide-substrate interface is strong and the load is low.

42 ENGINEERING↗