Search NASA⌕ Search

SEARCH · Search NASA

Results for “current density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

High Specific Power Motors in LN2 and LH2

A switched reluctance motor has been operated in liquid nitrogen (LN2) with a power density as high as that reported for any motor or generator. The high performance stems from the low resistivity of Cu at LN2 temperature and from the geometry of the windings, the combination of which permits steady-state rms current density up to 7000 A/sq cm, about 10 times that possible in coils cooled by natural convection at room temperature. The Joule heating in the coils is conducted to the end turns for rejection to the LN2 bath. Minimal heat rejection occurs in the motor slots, preserving that region for conductor. In the end turns, the conductor layers are spaced to form a heat-exchanger-like structure that permits nucleate boiling over a large surface area. Although tests were performed in LN2 for convenience, this motor was designed as a prototype for use with liquid hydrogen (LH2) as the coolant. End-cooled coils would perform even better in LH2 because of further increases in copper electrical and thermal conductivities. Thermal analyses comparing LN2 and LH2 cooling are presented verifying that end-cooled coils in LH2 could be either much longer or could operate at higher current density without thermal runaway than in LN2.

Brown, Gerald V.↗
NASA NTRS1984

Photospheric electric current and transition region brightness within an active region

Distributions of vertical electrical current density J(z) calculated from vector measurements of the photospheric magnetic field are compared with ultraviolet spectroheliograms to investigate whether resistive heating is an important source of enhanced emission in the transition region. The photospheric magnetic fields in Active Region 2372 were measured on April 6 and 7, 1980 with the Marshall Space Flight Center vector magnetograph; ultraviolet wavelength spectroheliograms (L-alpha and N V 1239 A) were obtained with the UV Spectrometer and Polarimeter experiment aboard the Solar Maximum Mission satellite. Spatial registration of the J(z) (5 arcsec resolution) and UV (3 arcsec resolution) maps indicates that the maximum current density is cospatial with a minor but persistent UV enhancement, but there is little detected current associated with other nearby bright areas. It is concluded that, although resistive heating may be important in the transition region, the currents responsible for the heating are largely unresolved in the present measurements and have no simple correlation with the residual current measured on 5-arcsec scales.

Deloach, A. C.↗
DOE OSTI2025

Synthesis of multicomponent oxygen evolution reaction coatings via block copolymer templating with vapor- and solution-phase precursors

Porous mixed transition metal oxide heterostructures are promising electrocatalysts due to their high surface area. However, achieving conformal multicomponent oxide coatings with controlled nanoscale architectures remains challenging. Here, we report a synthesis strategy that integrates solution-based swelling infiltration (SBI) with gas-phase sequential infiltration synthesis (SIS) in a block copolymer template to fabricate porous, high-surface-area, conformal mixed-oxide electrocatalytic coatings. In this approach, a PS75-P4VP25 block copolymer (BCP) film is first infiltrated with transition metal acetylacetonate precursors via SBI, followed by exposure to gas phase precursors of ZnO via SIS process. Thermal annealing of the infiltrated BCP films converts them into all-inorganic Fe–ZnO, Fe–Co–ZnO, and Fe–Ni–ZnO coatings. Electrochemical testing on 70 nm thick conformal coatings demonstrates promising oxygen evolution reaction (OER) activity in alkaline media, with mass-specific current densities up to 1.0 × 10 5 mA/g at an overpotential of 330 mV (vs. RHE) at ultralow loading (~0.005 g/cm 2 ). Among the compositions, Fe–Co–ZnO and amorphous Fe–Ni–ZnO show the best OER performance, delivering current densities of 2.00 and 3.04 mA/cm 2 , respectively, compared to 1.52 mA/cm 2 for Fe–ZnO.. This work establishes SBI–SIS as a versatile route for fabricating nm-thin, high-performance multicomponent oxide heterostructures on cost-efficient supports, enabling efficient catalyst utilization in electrochemical energy conversion application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Ternary Phosphides Ba M 2 P 2 : Tailoring Crystal and Electronic Structures Enables Highly Efficient HER Electrocatalysis

Binary transition metal phosphides and their solid solutions have emerged as promising hydrogen evolution reaction (HER) catalysts. Although many research endeavors have adopted strategies to vary compositions to optimize catalytic performance, they mainly focus on binary structures, which represent only a small fraction of the abundant phase space of structure types among transition metal phosphides. Here, the largely unexplored class of ternary and multinary ordered phosphides in catalysis comprises two or more metals with quite different chemical nature, concealing the structure–property relationships essential for advancing catalyst design. Here, we explored phosphides crystallizing in one of the most abundant ordered intermetallic structure types, —the ThCr 2 Si 2 type, —where square nets of 3d transition metal M and P atoms are separated by layers of electropositive Ba cations. Four ternary BaM 2 P 2 (M = Fe, Fe/Cu, Fe/Ni, Ni) catalysts were synthesized and characterized. BaNi 2 P 2 showed high HER activity in acidic electrolyte, which required an overpotential, η 10 , of only 62 mV to drive current density j = –10 mA/cm 2 and high stability with a potential drop rate of 0.25 mV/h. BaNi 2 P 2 outperformed other Ni-based catalysts, such as Ni 2 P and Ni 5 P 4 . Notably, at current densities above –170 mA/cm 2 , BaNi 2 P 2 outperformed the standard Pt electrode measured under identical conditions. Electronic structure analysis revealed a volcano-type activity trend among the four BaM 2 P 2 catalysts based on their d-band center positions, highlighting the role of electropositive Ba cations in shifting the Ni-3d orbitals into an optimal position.

BaNi2P2↗
DOE OSTI2025

Modeling Electrodeposition in 3D Porous Architectures for Solid-State Li-Metal Batteries

Li-metal storage in three-dimensional (3D) electrodes is considered a potential dendrite-mitigation strategy. The large surface area and high porosity of these electrodes result in reduced local Li-plating current densities. The porous topology provides a scaffold for Li-deposition and stripping, maintaining both mechanical integrity and Li accessibility. The goal of this study is to understand how characteristics, such as geometry and material properties, affect the current distribution and deposition pattern. To this end, we developed a computational method to track material growth driven by electrodeposition within a complex geometry. This method ensures that the finite-element discretization remains conforming to the moving boundary while preserving an adequate mesh quality, and thus maintains solution accuracy. Using this new computational tool, we analyze the conditions under which porous anode architectures effectively expand the surface area of the charge-transfer interface, and self-regulate current density and dendrite growth.

3D electrode architectures↗
NASA NTRS1990

Electrical characterization of chemically modified YBa2Cu3O(7-x) surfaces

Results on electrical characterization of YBa2Cu3O(7-x) thin-film surfaces treated with a Br/ethanol chemical etch are presented. Electrical measurements of YBa2Cu3O(7-x)/Au/Nb device structures fabricated using polycrystalline, post-annelaed YBa2Cu3O(7-x) films with Br-etched surfaces, show improvements of approximately one or two orders of magnitude in current densities and resistivities (resistance-area products) relative to unetched devices. The existence of supercurrents in these structures has been confirmed by observation of the ac Josephson effect, and by magnetic field and temperature studies of the critical currents. The Br-etch process has produced 10 x 10 sq micron devices with critical current densities greater than 400 A/sq cm and resistivities as low as 4 x 10 to the -7th ohm/sq cm.

Hunt, B. D.↗
DOE OSTI2025

Nickel Sulfide-Nanowire-Filled Carbon Nanotubes as an Efficient Overall Water Splitting Electrocatalyst

Pursuing stable, efficient, and cost-effective nanostructured bifunctional electrocatalysts is crucial for advancing the electrochemical water splitting process and enabling clean hydrogen energy production. In recent years, considerable efforts have focused on developing highly efficient and durable commercial electrocatalysts for the oxygen evolution reaction (OER) and overall water splitting (OWS). This research introduces an OWS electrocatalyst-nickel sulfide-filled carbon nanotubes grown on a carbon cloth substrate (Ni 3 S 2 @CNTs/CC), synthesized via a one-step in-situ process. The synergistic integration of metal sulfide (Ni 3 S 2 ) and carbon nanotubes provides abundant active sites for catalytic reactions, ensuring a robust composite nanostructure with enhanced durability. Furthermore, the electrocatalytic performance for OER and OWS has been significantly improved by a simple acid treatment to the electrocatalysts, which introduces physical and chemical defects, particularly oxygen functional groups (the acid-treated sample is termed as Ni 3 S 2 @CNTs/CC-AT). As OER electrocatalysts, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT present overpotentials of 304 and 200 mV, respectively, for achieving a current density of 10 mA/cm 2 in the OER process. Furthermore, for complete water splitting in 1.0 M KOH electrolyte, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT exhibit potentials of 1.63 and 1.44 V, respectively, to achieve a current density of 10 mA/cm 2 when employed as both anode and cathode. Moreover, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT demonstrate durable nature for 22 and 20 h durability in the OER and OWS processes, respectively, offering a promising alternative to ruthenium- and iridium-based electrocatalysts for electrochemical hydrogen production through water splitting. In conclusion, the in-situ synthesis method and acid treatment strategy described in this research are promising approaches to fabricating high-performance encapsulated carbon-nanotube-based electrocatalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tunnel oxide passivating contact enabled by polysilicon on ultra-thin SiO 2 for advanced silicon radiation detectors

Conventional silicon junction detectors encounter significant carrier recombination within the heavily doped p⁺ and n⁺ layers, as well as beneath the metal contact regions, creating the so-called “dead layers”, especially on the detector side. In this study, we present the tunnel oxide passivating contact with doped polysilicon on oxide, which demonstrates exceptional surface passivation and carrier selectivity. The key innovation lies in an ultra-thin (~ 1.5 nm) interfacial oxide layer that facilitates efficient majority carrier transportation via tunneling while effectively block minority carriers. Remarkably low saturation current densities, ranging from 5 to 10 fA/cm² even with the metal contact, underscore the superiority of both n-type and p-type tunnel oxide passivating contacts. In contrast, conventional p–n junction or high-low junction exhibit saturation current densities ranging from 10 to 90 fA/cm² in the studied p⁺ and n⁺ layers with surface passivation schemes due to Auger recombination and surface recombination, and 1000–6000 fA/cm² with metal contacts due to intense metal-induced recombination at the interface. These findings indicate the potential and superiority of implementing n-type tunnel oxide passivating contact on the detector side and p-type contact on the back side for advanced silicon radiation detectors. This approach would enable thorough collection of generated charge carriers along the track of incident ionizing radiation particles, leading to improved energy resolution and reduced noise levels.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1975

15 cm cusped magnetic field mercury ion thruster research

The importance of achieving a uniform current density in the exhaust beam of an electrostatic ion thruster is discussed in terms of thrust level and accelerator grid lifetime. A neutral residence time approach is used to propose a magnetic field geometry which should produce a highly uniform beam current density. The discharge chamber length to diameter ratio is shown to be an important optimization parameter and experimental evaluation of the cusped field thruster over a wide range of this parameter is presented. Beam profile measurements 5 cm downstream of the accelerator grid indicate a beam profile flatness parameter which is 25% greater than the SERT II value. Flatness parameters extrapolated to the plane of the accelerator grid are demonstrated to be as high as 0.9.

Beattie, J. R.↗
NASA NTRS1985

Optical characteristics of lightning and thunderstorm currents

Researchers determined that lightning can be used to determine the diurnal variations of thunderstorms, i.e., storms that produce audible thunder, and that these variations are also in good agreement with diurnal variations in rainfall and convective activity. Measurements of the Maxwell current density, J sub m, under active thunderstorms show that this physical quantity is quasi-steady between lightning discharges and that lightning does not produce large changes in J sub m. Maps of J sub m show contours of iso-current density that are consistent with the locations of radar echos and the locations of where lightning has altered the cloud charge distribution.

Krider, E. P.↗
DOE OSTI2024

Stable Pentagonal Layered Palladium Diselenide Enables Rapid Electrosynthesis of Hydrogen Peroxide

Electrosynthesis of hydrogen peroxide (H 2 O 2 ) via the two-electron oxygen reduction reaction (2e – ORR) is promising for various practical applications, such as wastewater treatment. However, few electrocatalysts are active and selective for 2e – ORR yet are also resistant to catalyst leaching under realistic operating conditions. Here, a joint experimental and computational study reveals active and stable 2e – ORR catalysis in neutral media over layered PdSe 2 with a unique pentagonal puckered ring structure type. Computations predict active and selective 2e – ORR on the basal plane and edge of PdSe 2 , but with distinct kinetic behaviors. Further, electrochemical measurements of hydrothermally synthesized PdSe 2 nanoplates show a higher 2e – ORR activity than other Pd–Se compounds (Pd 4 Se and Pd 17 Se 15 ). PdSe 2 on a gas diffusion electrode can rapidly accumulate H 2 O 2 in buffered neutral solution under a high current density. The electrochemical stability of PdSe 2 is further confirmed by long device operational stability, elemental analysis of the catalyst and electrolyte, and synchrotron X-ray absorption spectroscopy. This work establishes a new efficient and stable 2e – ORR catalyst at practical current densities and opens catalyst designs utilizing the unique layered pentagonal structure motif.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Thirty-centimeter-diameter ion milling source

A 30-cm beam diameter ion source has been designed and fabricated for micromachining and sputtering applications. An argon ion current density of 1 mA/cu cm at 500 eV ion energy was selected as a design operating condition. The completed ion source met the design criteria at this operating condition with a uniform and well-collimated beam having an average variation in current density of + or - 5% over the center of 20 cm of the beam. This ion source has a multipole magnetic field that employs permanent magnets between permeable pole pieces. Langmuir probe surveys of the source plasma support the design concepts of a multipole field and a circumferential cathode to enhance plasma uniformity.

Robinson, R. S.↗
NASA NTRS1978

Adhesive bonding of ion beam textured metals and fluoropolymers

An electron bombardment argon ion source was used to ion etch various metals and fluoropolymers. The metal and fluoropolymers were exposed to (0.5 to 1.0) keV Ar ions at ion current densities of (0.2 to 1.5) mA/sq cm for various exposure times. The resulting surface texture is in the form of needles or spires whose vertical dimensions may range from tenths to hundreds of micrometers, depending on the selection of beam energy, ion current density, and etch time. The bonding of textured surfaces is accomplished by ion beam texturing mating pieces of either metals or fluoropolymers and applying a bonding agent which wets in and around the microscopic cone-like structures. After bonding, both tensile and shear strength measurements were made on the samples. Also tested, for comparison's sake, were untextured and chemically etched fluoropolymers. The results of these measurements are presented.

Mirtich, M. J.↗
NASA NTRS1978

Adhesive bonding of ion beam textured metals and fluoropolymers

An electron-bombardment argon ion source was used to ion-etch various metals and fluoropolymers. The metal and fluoropolymers were exposed to (0.5 to 1.0)-keV Ar ions at ion current densities of 0.2 to 1.5 mA/sq cm for various exposure times. The resulting surface texture is in the form of needles or spires whose vertical dimensions may range from tenths to hundreds of micrometers, depending on the selection of beam energy, ion current density, and etch time. The bonding of textured surfaces is accomplished by ion-beam texturing mating pieces of either metals or fluoropolymers and applying a bonding agent which wets in and around the microscopic conelike structures. After bonding, both tensile and shear strength measurements were made on the samples. Also tested, for comparison's sake, were untextured and chemically etched fluoropolymers. The results of these measurements are presented in this paper.

Mirtich, M. J.↗
DOE OSTI2023

High Sulfur Loading and Capacity Retention in Bilayer Garnet Sulfurized‐Polyacrylonitrile/Lithium‐Metal Batteries with Gel Polymer Electrolytes

The cubic‐garnet (Li 7 La 3 Zr 2 O 12 , LLZO) lithium–sulfur battery shows great promise in the pursuit of achieving high energy densities. The sulfur used in the cathodes is abundant, inexpensive, and possesses high specific capacity. In addition, LLZO displays excellent chemical stability with Li metal; however, the instabilities in the sulfur cathode/LLZO interface can lead to performance degradation that limits the development of these batteries. Therefore, it is critical to resolve these interfacial challenges to achieve stable cycling. Here, an innovative gel polymer buffer layer to stabilize the sulfur cathode/LLZO interface is created. Employing a thin bilayer LLZO (dense/porous) architecture as a solid electrolyte and significantly high sulfur loading of 5.2 mg cm −2 , stable cycling is achieved with a high initial discharge capacity of 1542 mAh g −1 (discharge current density of 0.87 mA cm −2 ) and an average discharge capacity of 1218 mAh g −1 (discharge current density of 1.74 mA cm −2 ) with 80% capacity retention over 265 cycles, at room temperature (22 °C) and without applied pressure. Achieving such stability with high sulfur loading is a major step in the development of potentially commercial garnet lithium–sulfur batteries.

25 ENERGY STORAGE↗
NASA NTRS2015

Fine-Filament MgB2 Superconductor Wire

Hyper Tech Research, Inc., has developed fine-filament magnesium diboride (MgB2) superconductor wire for motors and generators used in turboelectric aircraft propulsion systems. In Phase I of the project, Hyper Tech demonstrated that MgB2 multifilament wires (<10 micrometers) could reduce alternating current (AC) losses that occur due to hysteresis, eddy currents, and coupling losses. The company refined a manufacturing method that incorporates a magnesium-infiltration process and provides a tenfold enhancement in critical current density over wire made by a conventional method involving magnesium-boron powder mixtures. Hyper Tech also improved its wire-drawing capability to fabricate fine multifilament strands. In Phase II, the company developed, manufactured, and tested the wire for superconductor and engineering current density and AC losses. Hyper Tech also fabricated MgB2 rotor coil packs for a superconducting generator. The ultimate goal is to enable low-cost, round, lightweight, low-AC-loss superconductors for motor and generator stator coils operating at 25 K in next-generation turboelectric aircraft propulsion systems.

Cantu, Sherrie↗
NASA NTRS1988

Minimum dissipation rates in magnetohydrodynamics

Minimum dissipation rate states are explored for a current-carrying channel of magnetofluid, supported by a dc magnetic field and driven by an applied electric field. The minimization is carried out subject to the constraints of constant axial (toroidal) magnetic flux and constant time-averaged rate of supply of magnetic helicity. The solutions of the resulting Euler-Lagrange equations are sensitive to boundary conditions on the current density j. One set of boundary conditions on j leads to the same consequences as Taylor's 'minimum-energy' theory. A different set leads to significantly different consequences, including a departure from the 'force-free' magnetic profile and a toroidal component of current density that does not reverse at the wall when the toroidal magnetic field reverses.

Montgomery, David↗
NASA NTRS1996

Development of Prototype HTS Components for Magnetic Suspension Applications

We have concentrated on developing prototype lengths of bismuth and thallium based silver sheathed superconductors by the powder-in-tube approach to fabricate high temperature superconducting (HTS) components for magnetic suspension applications. Long lengths of mono and multi filament tapes are presently being fabricated with critical current densities useful for maglev and many other applications. We have recently demonstrated the prototype manufacture of lengths exceeding 1 km of Bi-2223 multi filament conductor. Long lengths of thallium based multi-filament conductor have also been fabricated with practical levels of critical current density and improved field dependence behavior. Test coils and magnets have been built from these lengths and characterized over a range of temperatures and background fields to determine their performance. Work is in progress to develop, fabricate and test HTS windings that will be suitable for magnetic suspension, levitation and other electric power related applications.

Haldar, P.↗