Stabilizing Transition Metal Vacancy Induced Oxygen Redox by Co 2+ /Co 3+ Redox and Sodium-Site Doping for Layered Cathode Materials
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Search NASA
Results for “cycling stability”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Accommodation of Silicon in an Interconnected Copper Network for Robust Li-Ion Storage
Silicon (Si)-based materials are one of the most promising anodes to be applied in rechargeable lithium ion batteries. However, the active Si/electrolyte interface causes continuous side reactions and poor conductivity, which significantly decreases the cycling stability. Cu is the only metallic current collector that has been known to promote electron conduction and lithium-ion transfer without alloying reaction occurrence. However, to the best current knowledge, scalable interface engineering incorporating Cu has not been reported. In this study, this conductive Cu interface (CCI) is constructed through a self-assembly carbothermic reduction method to achieve efficient protection of Si/electrolyte interfaces while allowing for fast Li + diffusion. The energy barrier of lithium-ion diffusion through Cu is calculated to be 0.1965 eV, which is much lower than that through Au, Fe, and Ni films. Benefiting from the enhanced interfacial protection and kinetics of Si with CCI, a fading rate of only 0.068% is maintained for 1000 cycles and an aerial capacity of 4.78 mAh cm -2 is achieved after 280 cycles, which is comparable to the industry standards required for practical application.
36 MATERIALS SCIENCE↗
Architecting a Stable High-Energy Aqueous Al-Ion Battery
Aqueous Al-ion batteries (AAIBs) are the subject of great interest due to the inherent safety and high theoretical capacity of aluminum. The high abundancy and easy accessibility of aluminum raw materials further make AAIBs appealing for grid-scale energy storage. However, the passivating oxide film formation and hydrogen side reactions at the aluminum anode as well as limited availability of the cathode lead to low discharge voltage and poor cycling stability. Here, we proposed a new AAIB system consisting of an Al x MnO 2 cathode, a zinc substrate-supported Zn-Al alloy anode, and an Al(OTF) 3 aqueous electrolyte. Through the in situ electrochemical activation of MnO, the cathode was synthesized to incorporate a two-electron reaction, thus enabling its high theoretical capacity. The anode was realized by a simple deposition process of Al 3+ onto Zn foil substrate. The featured alloy interface layer can effectively alleviate the passivation and suppress the dendrite growth, ensuring ultralong-term stable aluminum stripping/plating. The architected cell delivers a record-high discharge voltage plateau near 1.6 V and specific capacity of 460 mAh g -1 for over 80 cycles. Finally, this work provides new opportunities for the development of high-performance and low-cost AAIBs for practical applications.
25 ENERGY STORAGE↗
Stability Enhancement in Na 0.67 Fe 0.2 Mn 0.8 O 2 Positive Electrodes via Spherical Coprecipitated Hydroxide Precursor Synthesis for Na-Ion Batteries
Mn/Fe-based layered transition metal oxides (LTMOs) are promising positive electrode materials for sodium-ion batteries (SIBs) due to their high abundance, low cost, and stable price fluctuations. At commercial scale, the fabrication of these materials commonly employs coprecipitation of hydroxide precursors, which allows for the scalable synthesis of uniform, dense particles with a tunable morphology. However, the common chelating agent (ammonia) forms unstable complexes with Fe 2+ ions, resulting in uncontrollable particle morphology and poor electrochemical properties. Here, in this study, three chelation strategies (no chelation, ammonia, oxalate) for Fe/Mn-based hydroxides are evaluated. It was found that oxalate chelation produced uniform, dense spherical hydroxide particles while particles via ammonia / no chelate routes exhibited no morphological control. The LTMOs synthesized from the oxalate-chelated hydroxide precursor formed uniform spherical particles, while the other two LTMOs showed greater variation in particle morphology. The oxalate-chelated LTMO electrode exhibited increased cycling stability due to reduced parasitic reactions with the electrolyte, as characterized by static leakage current measurements and electrochemical impedance spectroscopy.
25 ENERGY STORAGE↗
P2-Type Moisture-Stable and High-Voltage-Tolerable Cathodes for High-Energy and Long-Life Sodium-Ion Batteries
P2-Na 0.67 Ni 0.33 Mn 0.67 O 2 represents a promising cathode for Na-ion batteries, but it suffers from severe structural degradation upon storing in a humid atmosphere and cycling at a high cutoff voltage. Here we propose an in situ construction to achieve simultaneous material synthesis and Mg/Sn cosubstitution of Na 0.67 Ni 0.33 Mn 0.67 O 2 via one-pot solid-state sintering. Here, the materials exhibit superior structural reversibility and moisture insensitivity. In-operando XRD reveals an essential correlation between cycling stability and phase reversibility, whereas Mg substitution suppressed the P2–O2 phase transition by forming a new Z phase, and Mg/Sn cosubstitution enhanced the P2–Z transition reversibility benefiting from strong Sn–O bonds. DFT calculations disclosed high chemical tolerance to moisture, as the adsorption energy to H 2 O was lower than that of the pure Na 0.67 Ni 0.33 Mn 0.67 O 2 . A representative Na 0.67 Ni 0.23 Mg 0.1 Mn 0.65 Sn 0.02 O 2 cathode exhibits high reversible capacities of 123 mAh g –1 (10 mA g –1 ), 110 mAh g –1 (200 mA g –1 ), and 100 mAh g –1 (500 mA g –1 ) and a high capacity retention of 80% (500 mA g –1 , 500 cycles).
25 ENERGY STORAGE↗
Elucidating the Synergic Effect in Nanoscale MoS 2 /TiO 2 Heterointerface for Na‐Ion Storage
Abstract Interface engineering in electrode materials is an attractive strategy for enhancing charge storage, enabling fast kinetics, and improving cycling stability for energy storage systems. Nevertheless, the performance improvement is usually ambiguously ascribed to the “synergetic effect”, the fundamental understanding toward the effect of the interface at molecular level in composite materials remains elusive. In this work, a well‐defined nanoscale MoS 2 /TiO 2 interface is rationally designed by immobilizing TiO 2 nanocrystals on MoS 2 nanosheets. The role of heterostructure interface between TiO 2 and MoS 2 by operando synchrotron X‐ray diffraction (sXRD), solid‐state nuclear magnetic resonance, and density functional theory calculations is investigated. It is found that the existence of a hetero‐interfacial electric field can promote charge transfer kinetics. Based on operando sXRD, it is revealed that the heterostructure follows a solid‐solution reaction mechanism with small volume changes during cycling. As such, the electrode demonstrates ultrafast Na + ions storage of 300 mAh g −1 at 10 A g −1 and excellent reversible capacity of 540 mAh g −1 at 0.2 A g −1 . This work provides significant insights into understanding of heterostructure interface at molecular level, which suggests new strategies for creating unconventional nanocomposite electrode materials for energy storage systems.
25 ENERGY STORAGE↗
Active Dendrite Suppression by Ferroelectric Membrane Separators in Rechargeable Batteries
Anodic dendrite formation is a critical issue in rechargeable batteries and often leads to poor cycling stability and quick capacity loss. Prevailing strategies for dendrite suppression aim at slowing down the growth rate kinetically but still leaving possibilities for dendrite evolution over time. Herein, we report a complete dendrite elimination strategy using a mesoporous ferroelectric polymer membrane as the battery separator. The dendrite suppression is realized by spontaneously reversing the surface energetics for metal ion reduction at the protrusion front, where a positive piezoelectric polarization is generated and superimposed as the protrusion compresses the separator. This effect is demonstrated first in a Zn electroplating process, and further in Zn–Zn symmetric cells and Zn–NaV 3 O 8 ·1.5H 2 O full cells, where the dendritic Zn anode surfaces are completely turned into featureless flat surfaces. Consequently, a substantially longer charging/discharging cycle is achieved. Furthermore, this study provides a promising pathway toward high-performance dendrite-free rechargeable batteries.
25 ENERGY STORAGE↗
Thickness-independent scalable high-performance Li-S batteries with high areal sulfur loading via electron-enriched carbon framework
Abstract Increasing the energy density of lithium-sulfur batteries necessitates the maximization of their areal capacity, calling for thick electrodes with high sulfur loading and content. However, traditional thick electrodes often lead to sluggish ion transfer kinetics as well as decreased electronic conductivity and mechanical stability, leading to their thickness-dependent electrochemical performance. Here, free-standing and low-tortuosity N, O co-doped wood-like carbon frameworks decorated with carbon nanotubes forest (WLC-CNTs) are synthesized and used as host for enabling scalable high-performance Li-sulfur batteries. EIS-symmetric cell examinations demonstrate that the ionic resistance and charge-transfer resistance per unit electro-active surface area of S@WLC-CNTs do not change with the variation of thickness, allowing the thickness-independent electrochemical performance of Li-S batteries. With a thickness of up to 1200 µm and sulfur loading of 52.4 mg cm −2 , the electrode displays a capacity of 692 mAh g −1 after 100 cycles at 0.1 C with a low E/S ratio of 6. Moreover, the WLC-CNTs framework can also be used as a host for lithium to suppress dendrite growth. With these specific lithiophilic and sulfiphilic features, Li-S full cells were assembled and exhibited long cycling stability.
36 MATERIALS SCIENCE↗
Machine learning-accelerated discovery of heat-resistant polysulfates for electrostatic energy storage
The development of heat-resistant dielectric polymers that withstand intense electric fields at high temperatures is critical for electrification. Balancing thermal stability and electrical insulation, however, is exceptionally challenging as these properties are often inversely correlated. A traditional intuition-driven polymer design approach results in a slow discovery loop that limits breakthroughs. Here we present a machine learning-driven strategy to rapidly identify high-performance, heat-resistant polymers. A trustworthy feed-forward neural network is trained to predict key proxy parameters and down select polymer candidates from a library of nearly 50,000 polysulfates. The highly efficient and modular sulfur fluoride exchange click chemistry enables successful synthesis and validation of selected candidates. A polysulfate featuring a 9,9-di(naphthalene)-fluorene repeat unit exhibits excellent thermal resilience and achieves ultrahigh discharged energy density with over 90% efficiency at 200 °C. Its exceptional cycling stability underscores its promise for applications in demanding electrified environments.
Li, He↗
3D–Integrated, Multi–Functional Carbon Fibers for Stable, High–Areal–Capacity Batteries
Increasing lithium-ion batteries' (LIBs) electrode areal capacity can boost energy density and lower manufacturing costs, but faces challenges in manufacturing, rate performance, and cycling stability. A conductive framework made of commercial micro-sized carbon fibers (Cfs) is presented that serves as a host for both the LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC 532) cathode and Cfs anode. The Cf framework has multiple functions that offer high electronic conductivity (270 mS cm –1 ), low tortuosity (1.7), low Li + diffusion resistance (22 Ω), and high thermal conductivity (200 W mK –1 ). Additionally, the Cf-integrated electrodes can have an extremely high mass loading of NMC 532 (70 mg cm –2 ) with a theoretical capacity of 14 mAh cm –2 . Thus, the practical full cells assembled with the Cfs-enabled electrodes exhibit an initial areal capacity of 4.1 mAh cm –2 and capacity retention of 90.4% at 500 cycles at a cycling rate of C/3, 1.5 mA cm –2 . Data collected from the operando isothermal microcalorimetry suggest that full cells utilizing the Cf anode experience less heat release from side reactions compared to cells utilizing a conventional graphite anode. Finally, this present approach is scalable and cost-effective and can fabricate practical LIBs that boast high areal capacity, rate performance, and a lengthy cycling lifetime.
25 ENERGY STORAGE↗
Removal of Surface Carbonate from Lithium-Ion Battery Cathode Materials via Vapor-Phase Fluorination
Herein, ultrathin metal-fluoride barrier coatings on the surface of lithium-ion battery (LIB) cathodes can improve cycling stability and prevent corrosion by acidic byproducts in the electrolyte. Atomic layer deposition (ALD) is an effective method to deposit ultrathin metal fluoride coatings on LIB cathodes. Although numerous studies have demonstrated the benefit of ALD metal fluoride coatings to LIB performance, comparatively few works have examined the effect of individual ALD precursors on the cathode surface. This paper uses X-ray photoelectron spectroscopy (XPS) measurements to elucidate the surface chemical changes on LIB cathode material surfaces upon exposure to the ALD metal fluoride precursor, hydrogen fluorine pyridine (HFPy). We found a decrease in surface carbonate and an increase in surface fluoride after HFPy exposure suggesting the conversion of lithium carbonate (Li 2 CO 3 ) to lithium fluoride (LiF). This conversion is desirable given that Li 2 CO 3 degrades LIB performance, whereas LiF provides an excellent physio-chemical barrier against chemical attack during cycling. Scanning transmission electron microscopy, X-ray energy dispersive spectroscopy, and XPS measurements following HFPy exposure to Li 2 CO 3 powder revealed the formation of a conformal LiF shell around the Li 2 CO 3 particles. Finally, we confirmed the complete conversion of similar to 7 nm ALD Li 2 CO 3 films on silicon from HFPy exposure using XPS and spectroscopic ellipsometry. The elimination of problematic Li 2 CO 3 from LIB cathode surfaces and conversion into a protective LiF coating via a single precursor vapor treatment may provide a cost-effective method for enhancing LIB performance.
25 ENERGY STORAGE↗
PtRu Catalysts on Nitrogen-Doped Carbon Nanotubes with Conformal Hydrogenated TiO 2 Shells for Methanol Oxidation
The methanol oxidation reaction (MOR) is the limiting factor in direct methanol fuel cells (DMFC). There is an urgent need to improve the catalytic activity and stability of MOR catalysts. This study reports a highly active PtRu catalyst for MOR based on a hybrid multifunctional catalyst support consisting of a conformal amorphous hydrogenated TiO 2 shell wrapped around the oxygenated N-doped carbon nanotube core, denoted as PtRu/TiO 2 / ONCNT-400. Both the TiO 2 shell and the subsequent PtRu nanoparticles are deposited by a rapid microwave-assisted synthesis processes. The hydrogenated TiO 2 shell is found to exhibit a strong interaction with the deposited PtRu catalyst nanoparticles and effectively prevent them from agglomeration during the postdeposition thermal annealing to form more active crystalline PtRu alloy catalysts. In addition, the defective hydrogenated TiO 2 shell enhances the PtRu catalyst activity by the synergistic effects of partial charge transfer from TiO 2 to PtRu and high oxophilicity, which improves the kinetics of oxidation of poisonous CO intermediate to CO 2 . The mass activity for MOR and long-cycling stability of the PtRu/TiO 2 /ONCNT-400 catalyst surpass the two benchmark commercial PtRu/C catalysts from Johnson Matthey (JM) and Tanaka KiKinzoku (TKK), respectively. Furthermore, the results demonstrate that PtRu/TiO 2 /ONCNT-400 can serve as an efficient catalyst for MOR in DMFC.
36 MATERIALS SCIENCE↗
Critical Insights into Solvent Choice for High-Voltage Organosulfur Electrolytes
Organosulfur electrolytes are promising candidates for enabling high-voltage cathodes due to their superior oxidative stability compared to conventional carbonate-based systems. However, their viscous nature and inability to passivate the anode necessitate the use of passivating agents and diluents to achieve meaningful charge/discharge rates. In this study, we investigate the use of cyclic fluorinated carbonates (CFCs) to form passivating interphases on electrode surfaces, aiming to optimize electrolyte performance in high-voltage systems. Electrolyte formulations containing 1.2 M LiPF 6 in a CFC:sulfone:1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) mixture (2/5/3 V/V/V) were assessed in full-cell configurations with a LiNi 0.8 Mn 0.1 Co 0.1 O 2 (FCG-NMC) cathode and a 4.5 V upper cutoff potential. The results reveal that 3-3-3-trifluoropropylene carbonate (TFPC) combined with ethyl methyl sulfone (EMS) optimizes electrolyte performance, resulting in lower resistance buildup and reduced capacity loss compared to commercial electrolytes. We also explore the failure mechanisms of several carbonate/sulfone mixtures and identify key considerations for electrolyte compatibility in high-voltage systems. TFPC enhances cycling stability and lowers overall cell resistance, while fluoroethylene carbonate (FEC) formulations, despite higher ionic conductivity, fail to form adequate passivation layers, leading to rapid capacity loss. Additionally, EMS provides superior physical properties that avoid common failure modes seen with other sulfone solvents like methyl isopropyl sulfone and tetramethylene sulfone. Furthermore, this study underscores the importance of carefully selecting passivating carbonates and sulfone solvents to improve electrolyte performance and expand the viability of high-voltage electrolyte systems.
LiNi0.8Mn0.1Co0.1O2 cathode↗
Organic Solvent Free Process to Fabricate High Performance Silicon/Graphite Composite Anode
Cycling stability is a key challenge for application of silicon (Si)-based composite anodes as the severe volume fluctuation of Si readily leads to fast capacity fading. The binder is a crucial component of the composite electrodes. Although only occupying a small amount of the total composite mass, the binder has major impact on the long-term electrochemical performance of Si-based anodes. In recent years, water-based binders including styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) have attracted wide research interest as eco-friendly and low-cost alternatives for the conventional poly(vinylidene difluoride) (PVDF) binder in Si anodes. In this study, Si-based composite anodes are fabricated by simple solid mixing of the active materials with subsequent addition of SBR and CMC binders. This approach bypasses the use of toxic and expansive organic solvents. The factors of binder, silicon, and graphite materials have been systematically investigated. It is found that the retained capacities of the anodes are more than 440 mAh/g after 400 cycles. These results indicate that organic solvent free process is a facile strategy for producing high performance silicon/graphite composite anodes.
Fang, Chen (ORCID:0000000321011991)↗
Enabling high areal capacity for Co-free high voltage spinel materials in next-generation Li-ion batteries
The rapidly growing technological demand for lithium-ion batteries has prompted the development of novel cathode materials with high energy density, low cost, and improved safety. High voltage spinel, LiNi 0.5 Mn 1.5 O 4 (LNMO), is one of the most promising candidates yet to be commercialized. The two primary obstacles for this material are the inferior electronic conductivity and fast capacity degradation in full cells due to the high operating voltage. By systematically addressing these limitations, we successfully develop a thick LNMO electrode with areal capacity loadings up to 3 mAh·cm –2 . The optimized thick electrode is paired with a commercial graphite anode at both the coin cell and pouch cell level, achieving a full cell capacity retention as high as 72% and 78%, respectively, after 300 cycles. We attribute this superior cycling stability to careful optimizations of cell components and testing conditions, with a specific focus improving electronic conductivity and high voltage compatibility. These results suggest precise control of materials quality, electrode architecture and electrolyte optimization can soon support the development of a cobalt-free battery system based on a thick LNMO cathode (>4 mAh·cm 2 ), which will eventually meet the needs of next-generation Li-ion batteries with reduced cost, improved safety, and assured sustainability.
25 ENERGY STORAGE↗
Structural and chemical evolutions of a magnesium vanadium oxide cathode under electrochemical cycling in magnesium batteries
The design of cathode materials that remain chemically and structurally stable during repetitive ion insertion and extraction poses a significant challenge in developing multivalent batteries. The cycling stability of traditional metal oxide-based cathode is challenged by sluggish diffusion of multivalent cations and parasitic reactivity at interfacial regimes, including the cathode electrolyte interphase layer (CEI). Understanding the reactions at the cathode-electrolyte interface, particularly those induced by non-stoichiometric surface layers, is a crucial design parameter for both cathode materials and electrolytes. Here, in this study, we employed multimodal analysis, including in situ and ex situ X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (TEM) and electrochemical impedance spectroscopy (EIS) to examine the surface reactions and subsequent structural and chemical evolutions of the CEI on high voltage magnesium vanadium oxide (MgV 2 O 4 ) spinel cathode during the Mg 2+ insertion/extraction processes. The results revealed that the presence of non-stoichiometric surface layers in the magnesium vanadium oxide cathode drive the decomposition of bis(trifluoromethanesulfonyl)imide (TFSI - ) anion, leading to the formation of the CEI layer. The CEI layer could inhibit the Mg 2+ ion transfer processes. Accompanying this reactivity-driven degradation, the magnesium vanadium oxide cathode undergoes pulverization, forming clusters of nanosized particles. This process likely improves cycling ability by creating new intercalation sites and shortening the diffusion pathway for the Mg 2+ cations. This study demonstrates that controlling surface stoichiometry and engineering morphological properties are critical design parameters for high performance cathodes for multivalent batteries.
25 ENERGY STORAGE↗
Spatial Progression of Polysulfide Reactivity with Lithium Nitrate in Li–Sulfur Batteries
LiNO 3 is a commonly used electrolyte additive in Li-S batteries, but the intricacies of its stabilizing effect on these batteries are not well-understood due to the complex chemical nature of Li-S electrolytes. This complexity often hampers clear characterization and interpretation of data. In this study, we explore the reactivity of LiNO 3 in Li-S batteries through in operando sulfur K-edge spectroscopy. To remove ambiguities, a sulfur-free electrolyte with LiNO 3 as the sole salt is used. This allows a precise elucidation of the reaction mechanism between LiNO 3 and polysulfides. Here, we observe that the reaction is chemical in nature and progresses spatially, influenced by the polysulfide concentration gradient across the electrolyte. Polysulfides are electrochemically generated in situ on the cathode side, leading to high local concentration. As a result, they cannot be fully oxidized by LiNO 3 and forms sulfites initially which are gradually further oxidized into sulfonates and sulfates. Conversely, polysulfides on the anode side have lower local concentration as they are not generated in situ but diffused from the cathode side. Their reaction with LiNO 3 leads to highly oxidized species like sulfonates and sulfates. These reaction products are not reduced during electrochemically cycling, suggesting their capabilities of passivating the electrodes and contributing to the cycle stabilities of Li-S batteries.
25 ENERGY STORAGE↗
Electrolytes with moderate lithium polysulfide solubility for high-performance long-calendar-life lithium–sulfur batteries
Lithium–sulfur (Li-S) batteries with high energy density and low cost are promising for next-generation energy storage. However, their cycling stability is plagued by the high solubility of lithium polysulfide (LiPS) intermediates, causing fast capacity decay and severe self-discharge. Exploring electrolytes with low LiPS solubility has shown promising results toward addressing these challenges. However, here, we report that electrolytes with moderate LiPS solubility are more effective for simultaneously limiting the shuttling effect and achieving good Li-S reaction kinetics. We explored a range of solubility from 37 to 1,100 mM (based on S atom, [S]) and found that a moderate solubility from 50 to 200 mM [S] performed the best. Using a series of electrolyte solvents with various degrees of fluorination, we formulated the S ingle- S olvent, S ingle- S alt, S tandard S alt concentration with M oderate L i PSs so l ubility E lectrolytes (termed S 6 MILE ) for Li-S batteries. Among the designed electrolytes, Li-S cells using fluorinated-1,2-diethoxyethane S 6 MILE (F4DEE-S 6 MILE) showed the highest capacity of 1,160 mAh g −1 at 0.05 C at room temperature. At 60 °C, fluorinated-1,4-dimethoxybutane S 6 MILE (F4DMB-S 6 MILE) gave the highest capacity of 1,526 mAh g −1 at 0.05 C and an average CE of 99.89% for 150 cycles at 0.2 C under lean electrolyte conditions. This is a fivefold increase in cycle life compared with other conventional ether-based electrolytes. Moreover, we observed a long calendar aging life, with a capacity increase/recovery of 4.3% after resting for 30 d using F4DMB-S 6 MILE. Furthermore, the correlation between LiPS solubility, degree of fluorination of the electrolyte solvent, and battery performance was systematically investigated.
25 ENERGY STORAGE↗