Search NASA⌕ Search

SEARCH · Search NASA

Results for “data center modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Tests and comparisons of satellite-derived geoids with Skylab altimeter data

During the Skylab 4 mission, the S-193 radar altimeter was operated nearly continuously for a revolution around the world on Jan. 31, 1974. This direct measurement to the sea surface has provided an independent basis for the evaluation of the precision of global geoids computed from satellite-derived earth gravity models. This paper presents comparisons between the Skylab data and several recent gravity models published by Goddard Space Flight Center, the Smithsonian Astrophysical Observatory, and the National Oceanic and Atmospheric Administration. The differences between the altimeter geoid and the satellite geoids were as large as 20 m, rms values ranging from 8 to 10 m. These differences also indicated a systematic long-wavelength variation (about 100 deg) not related to error in the Skylab orbits. Truncation of the models to degree and order 8 did not eliminate the long-wavelength variation, but in every case the rms agreement between the satellite geoids and the altimeter geoid was slightly improved. Orbits computed with the truncated models were found to be inferior to those computed with the complete models.

Marsh, J. G.↗
NASA NTRS1978

Low-speed test limit of V/STOL model located vertically off-center

A vertically off-centered V/STOL model - a 2-ft-diam three-bladed aluminum propeller operating in a rotor mode - is tested in an 8 by 12 ft wind tunnel with and without ground plane along with an associated 3 by 4.5 ft test section insert. The objective was to assess the effect of the vertically off-centered model on the low-speed test limit. The aerodynamic data of the model at a constant negative angle of attack (-3 deg) are recorded at selected tunnel dynamic pressures to provide adequate data points to define the model lift variation with respect to the tip speed ratio. The adverse effect of the rotor low-speed test limit is observed in the form of lift change with respect to the tip speed ratio. A major conclusion is that for rotors tested with a ground plane or in the vicinity of the floor, the ratio of distance between floor and model to rotor radius defines the low-speed test limits.

Shindo, S.↗
NASA NTRS1980

Clear air turbulence forecasting techniques

A method to improve clear air turbulence (CAT) forecasting by more effectively using the currently operational rawinsonde (RW) system is discussed. The method is called the Diagnostic Richardson Number Tendency (DRT) technique. The technique does not attempt to use the RW as a direct detector of the turbulent motion or even of the CAT mechanism structure but rather senses the synoptic scale centers of action which provide the energy to the CAT mechanism at the mesoscale level. The DRT algorithm is deterministic rather than statistical in nature, using the hydrodynamic equations (equations of motion) relevant to the synoptic scale. However, interpretation, by necessity, is probabilistic. What is most important with respect to its operational implementation is that this method uses the same input data as currently used by the operational National Meteorological Center prognostic models.

Keller, J. L.↗
NASA NTRS1982

A preliminary study of the particulate fallout from the space shuttle (STS-1)

Prediction of acid fallout and the dry deposition of Al2O2 was the objective of this investigation. Sampling was done at the Kennedy Space Center in Florida. The models available were not appropriate and the data available was negligible. Thus, a bimodal particle distribution was assumed normalized to the few existing data points and used as a foundation for a crude zeroth order approximation for the acid fallout. In addition, a settling spectrum for the Al2O3 particles was devised as a table look-up since the graphs in the literature at first pass could not be fitted with reasonable analytic functions. Consulting services were rendered to researchers. Special emphasis was placed on improving current techniques and adding LIDAR (Light Radar). Suggestions for future studies are made.

Hudson, G. M.↗
NASA NTRS1982

Global mean sea surface computation using GEOS 3 altimeter data

A mean sea surface map has been determined for the global ocean areas between +62 deg and -62 deg latitude using GEOS 3 altimeter data. A grid of laser reference orbits computed using the GEM 10B gravity model has been used to orient the altimeter data in a center of mass coordinate system. The density of the altimeter tracks has enabled the computation of the sea surface heights above the reference ellipsoid on 1 deg x 1 deg grid in most of the oceanic areas. In the northwest Atlantic the dense coverage has enabled computations on a 0.25 deg x 0.25 deg grid. Comparisons of the global surface with an independently computed mean sea surface based upon SEASAT altimeter data indicate an rms agreement of a little over a meter. Comparisons of the regional solution in the northwest Atlantic with SEASAT profiles indicate a precision of a few decimeters in this surface. An analysis of the global crossover differences has indicated the possibility of a timing error in the altimeter data. Timing bias values of within 0.5 msec of 9.2 msec for 1975 and within 0.6 msec of 18.7 msec for 1976 have been recovered from an analysis of the altimeter data.

Marsh, J. G.↗
NASA NTRS1995

Ground-based grasslands data to support remote sensing and ecosystem modeling of terrestrial primary production

Estimating terrestrial net primary production (NPP) using remote-sensing tools and ecosystem models requires adequate ground-based measurements for calibration, parameterization, and validation. These data needs were strongly endorsed at a recent meeting of ecosystem modelers organized by the International Geosphere-Biosphere Program's (IGBP's) Data and Information System (DIS) and its Global Analysis, Interpretation, and Modelling (GAIM) Task Force. To meet these needs, a multinational, multiagency project is being coordinated by the IGBP DIS to compile existing NPP data from field sites and to regionalize NPP point estimates to various-sized grid cells. Progress at Oak Ridge National Laboratory (ORNL) on compiling NPP data for grasslands as part of the IGBP DIS data initiative is described. Site data and associated documentation from diverse field studies are being acquired for selected grasslands and are being reviewed for completeness, consistency, and adequacy of documentation, including a description of sampling methods. Data are being compiled in a database with spatial, temporal, and thematic characteristics relevant to remote sensing and global modeling. NPP data are available from the ORNL Distributed Active Archive Center (DAAC) for biogeochemical dynamics. The ORNL DAAC is part of the Earth Observing System Data and Information System, of the US National Aeronautics and Space Administration.

Olson, R. J.↗
NASA NTRS2000

BOREAS Regional DEM in Raster Format and AEAC Projection

This data set is based on the GTOPO30 Digital Elevation Model (DEM) produced by the United States Geological Survey EROS Data Center (USGS EDC). The BOReal Ecosystem-Atmosphere Study (BOREAS) region (1,000 km x 1000 km) was extracted from the GTOPO30 data and reprojected by BOREAS staff into the Albers Equal-Area Conic (AEAC) projection. The pixel size of these data is 1 km. The data are stored in binary, image format files.

Knapp, David↗
NASA NTRS2005

TAMDAR Sensor Validation in 2003 AIRS II

This study entails an assessment of TAMDAR in situ temperature, relative humidity and winds sensor data from seven flights of the UND Citation II. These data are undergoing rigorous assessment to determine their viability to significantly augment domestic Meteorological Data Communications Reporting System (MDCRS) and the international Aircraft Meteorological Data Reporting (AMDAR) system observational databases to improve the performance of regional and global numerical weather prediction models. NASA Langley Research Center participated in the Second Alliance Icing Research Study from November 17 to December 17, 2003. TAMDAR data taken during this period is compared with validation data from the UND Citation. The data indicate acceptable performance of the TAMDAR sensor when compared to measurements from the UND Citation research instruments.

Daniels, Taumi S.↗
NASA NTRS2008

Aeroheating Test of CEV Entry Vehicle at Turbulent Conditions

An investigation of the aeroheating environment of the Project Orion Crew Entry Vehicle has been performed in the Arnold Engineering Development Center Tunnel 9. Data were measured on a approx. 3.5% scale model (0.1778m/7-inch diam.) of the vehicle using coaxial thermocouples in the Mach 8 and Mach 10 nozzles of Tunnel 9. Runs were performed at free stream Reynolds numbers of 1 106/ft to 20 10(exp 6)/ft in the Mach 10 nozzle and 8 10(exp 6)/ft to 48 10(exp 6)/ft in the Mach 8 nozzle. The test gas in Tunnel 9 is pure N2, which at these operating conditions remains un-dissociated and may be treated as a perfect gas. At these conditions, laminar, transitional, and turbulent flow was produced on the model at Mach 10, and transitional and turbulent conditions were produced on the model at Mach 8. The majority of runs were made on a clean, smooth-surface model configuration and a limited number of runs were made in which inserts with varying boundary-layer trips configurations were used to force the occurrence of transition. Laminar and turbulent predictions were generated for all wind tunnel test conditions and comparisons were performed with the data for the purpose of helping to define uncertainty margins for the computational method. Data from both the wind tunnel test and the computations are presented herein. Figure 1 shows a schematic of the thermocouple locations on the model and figures 2 and 3 show a photo and schematic of the AEDC Hypervelocity Tunnel 9. Figure 4 shows a typical grid used in the computations. From the comparisons shown in figures 5 through 8 it was concluded that for perfect-gas conditions, the computations could predict either fully-laminar or full-turbulent flow to within +/-10% of the experimental data. The experimental data showed that transition began on the leeside of the heatshield at a free stream Reynolds number of 9 10(exp 6)/ft in the Mach 10 nozzle and fully-developed turbulent flow was produced at 20 10(exp 6)/ft. In the Mach 8 nozzle, transition on the leeside of the heat-shield was observed for all test conditions, and full-developed turbulent flow occurred at a free stream Reynolds number of 18 10(exp 6)/ft. On the aftbody of the vehicle no evidence of turbulence was detected at Mach 10 conditions, and at Mach 8 conditions, transition appeared to begin on the windside of the aftbody at free stream Reynolds number of 18x10(exp 6)/ft with fully-developed turbulent flow occurring only at the highest test condition of 48x10(exp 6)/ft.

Hollis, Brian R.↗
NASA NTRS2010

J-2X Turbopump Cavitation Diagnostics

The J-2X is the upper stage engine currently being designed by Pratt & Whitney Rocketdyne (PWR) for the Ares I Crew Launch Vehicle (CLV). Propellant supply requirements for the J-2X are defined by the Ares Upper Stage to J-2X Interface Control Document (ICD). Supply conditions outside ICD defined start or run boxes can induce turbopump cavitation leading to interruption of J-2X propellant flow during hot fire operation. In severe cases, cavitation can lead to uncontained engine failure with the potential to cause a vehicle catastrophic event. Turbopump and engine system performance models supported by system design information and test data are required to predict existence, severity, and consequences of a cavitation event. A cavitation model for each of the J-2X fuel and oxidizer turbopumps was developed using data from pump water flow test facilities at Pratt & Whitney Rocketdyne (PWR) and Marshall Space Flight Center (MSFC) together with data from Powerpack 1A testing at Stennis Space Center (SSC) and from heritage systems. These component models were implemented within the PWR J-2X Real Time Model (RTM) to provide a foundation for predicting system level effects following turbopump cavitation. The RTM serves as a general failure simulation platform supporting estimation of J-2X redline system effectiveness. A study to compare cavitation induced conditions with component level structural limit thresholds throughout the engine was performed using the RTM. Results provided insight into system level turbopump cavitation effects and redline system effectiveness in preventing structural limit violations. A need to better understand structural limits and redline system failure mitigation potential in the event of fuel side cavitation was indicated. This paper examines study results, efforts to mature J-2X turbopump cavitation models and structural limits, and issues with engine redline detection of cavitation and the use of vehicle-side abort triggers to augment the engine redline system.

Santi, I. Michael↗
NASA NTRS2005

Health Management Applications for International Space Station

Traditional mission and vehicle management involves teams of highly trained specialists monitoring vehicle status and crew activities, responding rapidly to any anomalies encountered during operations. These teams work from the Mission Control Center and have access to engineering support teams with specialized expertise in International Space Station (ISS) subsystems. Integrated System Health Management (ISHM) applications can significantly augment these capabilities by providing enhanced monitoring, prognostic and diagnostic tools for critical decision support and mission management. The Intelligent Systems Division of NASA Ames Research Center is developing many prototype applications using model-based reasoning, data mining and simulation, working with Mission Control through the ISHM Testbed and Prototypes Project. This paper will briefly describe information technology that supports current mission management practice, and will extend this to a vision for future mission control workflow incorporating new ISHM applications. It will describe ISHM applications currently under development at NASA and will define technical approaches for implementing our vision of future human exploration mission management incorporating artificial intelligence and distributed web service architectures using specific examples. Several prototypes are under development, each highlighting a different computational approach. The ISStrider application allows in-depth analysis of Caution and Warning (C&W) events by correlating real-time telemetry with the logical fault trees used to define off-nominal events. The application uses live telemetry data and the Livingstone diagnostic inference engine to display the specific parameters and fault trees that generated the C&W event, allowing a flight controller to identify the root cause of the event from thousands of possibilities by simply navigating animated fault tree models on their workstation. SimStation models the functional power flow for the ISS Electrical Power System and can predict power balance for nominal and off-nominal conditions. SimStation uses realtime telemetry data to keep detailed computational physics models synchronized with actual ISS power system state. In the event of failure, the application can then rapidly diagnose root cause, predict future resource levels and even correlate technical documents relevant to the specific failure. These advanced computational models will allow better insight and more precise control of ISS subsystems, increasing safety margins by speeding up anomaly resolution and reducing,engineering team effort and cost. This technology will make operating ISS more efficient and is directly applicable to next-generation exploration missions and Crew Exploration Vehicles.

Alena, Richard↗
NASA NTRS2018

Learning Reverse Engineering and Simulation with Design Visualization

The Design Visualization (DV) group supports work at the Kennedy Space Center by utilizing metrology data with Computer-Aided Design (CAD) models and simulations to provide accurate visual representations that aid in decision-making. The capability to measure and simulate objects in real time helps to predict and avoid potential problems before they become expensive in addition to facilitating the planning of operations. I had the opportunity to work on existing and new models and simulations in support of DV and NASA’s Exploration Ground Systems (EGS).

Hemsworth, Paul J.↗
NASA NTRS2014

The D8 Aircraft: An Aerodynamics Study of Boundary Layer and Wake Ingestion Benefit

Goal: Quantify benefits of BLI (Boundary Layer Ingesting) and wake ingestion for the D8. Approach: Overset CFD (Computational Fluid Dynamics) using CGT (Chimera Grid Tools software package) and Overflow-­‐2; CFD validation; NASA LaRC (Langley Research Center) 14x22 WT (wind tunnel) data for a 1:11 scale model; Quantifying the BLI and wake ingestion benefit - Direct Comparison between: Efficient conventional (podded nacelle) configuration; BLI (integrated nacelle) configuration.

D8↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32053-DND

The Atmospheric Science Data Center (ASDC) offers Earth Science data sets created from satellite measurements, modeling, and field experiments enabling scientists, educators, and the public to study earth and its atmosphere. NASA ESDIS is working towards making Earth Science data and tools cloud-ready. In an effort to align itself with these efforts, the ASDC is transitioning its existing web based services, tools and applications to RESTful APIs, containerized as microservices to leverage scalability and efficiency of an on-premise cloud environment.

Makhan L Virdi↗
NASA NTRS2020

Kenya Food Security & Agriculture II: Utilizing NASA Earth Observations to Enhance Drought Warning Systems and Develop Capacity to Use the RHEAS Model in Kenya

Twenty-three counties in Kenya experience frequent drought, which damages agricultural productivity and threatens the health and well being of millions. NASA DEVELOP partnered with NASA SERVIR, the Regional Centre for Mapping of Resources for Development (RCMRD) and Kenya’s National Drought Management Authority (NDMA) to enhance drought-detection capacity using NASA Earth observations. Currently, the NDMA publishes monthly Early Warning Bulletins with drought conditions for each arid or semi-arid county in Kenya. These bulletins utilize the Vegetation Condition Index (VCI) from the Moderate Resolution ImagingSpectroradiometer (MODIS) as well as a variety of biophysical, social and economic drought indicators, but do not allow for advanced forecasting. To improve drought-monitoring capabilities, the team created a Combined Drought Indicator (CDI) using the Regional Hydrologic Extremes Assessment System (RHEAS) model and data from Aqua and Terra MODIS and the National Centers for Environmental Prediction. The CDI combined precipitation anomalies, soil moisture anomalies, evaporative stress, and VCI according to weights determined by principal component analysis. To evaluate the performance of the CDI across Kenya, the team compiled a dataset of drought events from historical reports and the NDMA’s records. Results suggested that the CDI detected drought earlier thanVCI alone. However, more validation is needed to ensure that the CDI accurately and consistently detects drought earlier than current warning systems. In order to better understand the behavior of individual indices and the potential for earlier drought detection, the team also conducted a time-lag analysis. The team found that VCI responds to drought, on average, one month later than most other indices included in the CDI, suggesting that incorporating additional indices could improve early drought warning systems in Kenya.

Food Security & Agriculture↗
NASA NTRS2020

Kenya Food Security & Agriculture II: Utilizing NASA Earth Observations to Enhance Drought Warning Systems and Develop Capacity to Use the RHEAS Model in Kenya

Twenty-three counties in Kenya experience frequent drought, which damages agricultural productivity and threatens the health and well being of millions. NASA DEVELOP partnered with NASA SERVIR, the Regional Centre for Mapping of Resources for Development (RCMRD) and Kenya’s National Drought Management Authority (NDMA) to enhance drought-detection capacity using NASA Earth observations. Currently, the NDMA publishes monthly Early Warning Bulletins with drought conditions for each arid or semi-arid county in Kenya. These bulletins utilize the Vegetation Condition Index (VCI) from the Moderate Resolution Imaging Spectroradiometer (MODIS) as well as a variety of biophysical, social and economic drought indicators, but do not allow for advanced forecasting. To improve drought-monitoring capabilities, the team created a Combined Drought Indicator (CDI) using the Regional Hydrologic Extremes Assessment System (RHEAS) model and data from Aqua and Terra MODIS and the National Centers for Environmental Prediction.The CDI combined precipitation anomalies, soil moisture anomalies, evaporative stress, and VCI according to weights determined by principal component analysis. To evaluate the performance of the CDI across Kenya, the team compiled a dataset of drought events from historical reports and the NDMA’s records. Results suggested that the CDI detected drought earlier than VCI alone. However, more validation is needed to ensure that the CDI accurately and consistently detects drought earlier than current warning systems. In order to better understand the behavior of individual indices and the potential for earlier drought detection, the team also conducted a time-lag analysis. The team found that VCI responds to drought, on average, one month later than most other indices included in the CDI, suggesting that incorporating additional indices could improve early drought warning systems in Kenya.

Food Security & Agriculture↗
NASA NTRSDate not supplied

Treating gridded geospatial data as point data to simplify analytics

Gridded geospatial remote sensing (satellite) data has traditionally been stored in file-based multidimensional arrays to preserve the locality of data. Measurements from locations that are physically next to each other on earth remain next to each other in the arrays. Maintaining this locality is useful when running calculations like reprojection, but unnecessary for many other calculations. This talk will go through a real world example of a tool redesign at the Goddard Earth Sciences Data and Information Services Center (GES DISC), showing the advantages of using the data frame model for calculating summary statistics, where measurement proximity is unimportant.

Analysis-ready data↗