Search NASA⌕ Search

SEARCH · Search NASA

Results for “experimental measure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Method for Measuring Thermal Conductivity of Small Samples Having Very Low Thermal Conductivity

This paper describes the development of a hot plate method capable of using air as a standard reference material for the steady-state measurement of the thermal conductivity of very small test samples having thermal conductivity on the order of air. As with other approaches, care is taken to ensure that the heat flow through the test sample is essentially one-dimensional. However, unlike other approaches, no attempt is made to use heated guards to block the flow of heat from the hot plate to the surroundings. It is argued that since large correction factors must be applied to account for guard imperfections when sample dimensions are small, it may be preferable to simply measure and correct for the heat that flows from the heater disc to directions other than into the sample. Experimental measurements taken in a prototype apparatus, combined with extensive computational modeling of the heat transfer in the apparatus, show that sufficiently accurate measurements can be obtained to allow determination of the thermal conductivity of low thermal conductivity materials. Suggestions are made for further improvements in the method based on results from regression analyses of the generated data.

Miller, Robert A.↗
NASA NTRS2011

Assessment of Computational Fluid Dynamics (CFD) Models for Shock Boundary-Layer Interaction

A workshop on the computational fluid dynamics (CFD) prediction of shock boundary-layer interactions (SBLIs) was held at the 48th AIAA Aerospace Sciences Meeting. As part of the workshop numerous CFD analysts submitted solutions to four experimentally measured SBLIs. This paper describes the assessment of the CFD predictions. The assessment includes an uncertainty analysis of the experimental data, the definition of an error metric and the application of that metric to the CFD solutions. The CFD solutions provided very similar levels of error and in general it was difficult to discern clear trends in the data. For the Reynolds Averaged Navier-Stokes methods the choice of turbulence model appeared to be the largest factor in solution accuracy. Large-eddy simulation methods produced error levels similar to RANS methods but provided superior predictions of normal stresses.

DeBonis, James R.↗
NASA NTRS2020

Development of a Photosynthesis Measurement Chamber under Different Airspeeds for Applications in Future Space Crop-Production Facilities

Space crop production systems are being developed to grow fresh produce in-situ to supplement the astronauts’ diet, but the required ventilation rates for crops in different gravity environments remains poorly understood. The reduction or lack of buoyancy-driven convection in reduced gravity environments leads to impaired gas exchange (CO2 absorption, water transpiration and O2 release) at the leaf surface if no extra ventilation is provided, and this could lead to a reduction in biomass production in the long run. To better characterize the influence of different airspeeds on photosynthesis and be able to model this in low gravity, a chamber was designed to interface with a LI-6800 portable photosynthesis system. This paper details the design of this chamber, specifically made to measure whole-plant and small canopy gas exchange at different airspeeds. The fans provide turbulent mixing in the chamber to ensure that it behaves like a continuous stirred tank reactor (CSTR)and that the residence time distribution (RTD) is the same for any fan speed; the computational fluid dynamic (CFD) model of the gas domain (the air in the chamber) hence uses a k-omega turbulence model. An airflow map of the chamber was created using anemometer measurements for the different airspeeds tested, and this was used together with the CFD simulation results to relate the experimentally measured fan outputs to actual airspeeds on top of an artificial plant. Environmental parameters (air temperature, relative humidity, CO2level) are controlled by the LI-6800. This work was funded by NASA Space Biology through the NASA postdoctoral program / USRA.

Lucie Poulet↗
NASA NTRSDate not supplied

Multiphysics Computational Analysis of a Perforated Plate Cooling Flow

A multiphysics analysis of a film cooling flow was conducted using a computational fluid dynamics (CFD) solver in conjunction with a conjugate heat transfer (CHT) solver. The film cooling problem consisted of a square nozzle producing a heated subsonic jet over a perforated plate with three sections of 45 cooling holes each. Results from the multiphysics analysis were compared to a CFD-only approach and experimental results. Reynolds-averaged Navier-Stokes (RANS) computations were employed first, with and without the CHT solver. The multiphysics approach provided much closer agreement with experimentally measured plate temperatures than the CFD-only approach. Comparisons of computed velocities and temperatures were also made with experimental data. Hybrid RANS-large eddy simulation calculations employing the Delayed Detached Eddy Simulation (DDES) approach were also conducted within the multiphysics framework. The DDES approach was unable to resolve turbulent structures in the near wall regions. Hence, the RANS part of the DDES model was used in near wall regions, and produced surface temperatures along with velocity and temperature profiles close to the wall that were very similar to the RANS results. The DDES approach did resolve structures in the outer portion of the boundary layer especially near the end of the plate where the boundary layer was thicker. The key result was the improved surface temperatures produced by the multiphysics approach employing CHT over the fluid-only approach.

Computational Fluid Dynamics↗
NASA NTRS1989

Experience with advanced instrumentation in a hot section cascade

The Lewis Research Center gas turbine Hot Section Test Facility was developed to provide a real engine environment with known boundary conditions for the aerothermal performance evaluation and verification of computer design codes. This verification process requires experimental measurements in a hostile environment. The research instruments used in this facility are presented, and their characteristics and how they perform in this environment are discussed. The research instrumentation consisted of conventional pressure and temperature sensors, as well as thin-film thermocouples and heat flux gages. The hot gas temperature was measured by an aspirated temperature probe and by a dual-element, fast-response temperature probe. The data acquisition mode was both steady state and time dependent. These experiments were conducted over a wide range of gas Reynolds numbers, exit gas Mach numbers, and heat flux levels. This facility was capable of testing at temperatures up to 1600 K, and at pressures up to 18 atm. These corresponded to an airfoil exit Reynolds number range of 0.5 x 10(6) to 2.5 x 10(6) based on the airfoil chord of 5.55 cm. The results characterize the performance capability and the durability of the instrumentation. The challenge of making measurements in hostile environments is also discussed. The instruments exhibited more than adequate durability to achieve the measurement profile. About 70 percent of the thin-film thermocouples and the dual-element temperature probe survived several hundred thermal cycles and more than 35 hr at gas temperatures up to 1600 K. Within the experimental uncertainty, the steady-state and transient heat flux measurements were comparable and consistent over the range of Reynolds numbers tested.

Yeh, Frederick C.↗
NASA NTRS1976

Equilibrium and nonequilibrium electron density measurements in transient shock-heated hydrogen-helium plasmas

In the NASA planetary program, atmospheric entry probe missions to Jupiter, Saturn, and Uranus are potential programs now being planned for the 1980's. The work reported in this paper is concerned with predicting the electron density, and resulting radiative emission from the shock layer which must be accommodated by the entry probe heatshield. Within the hydrogen-helium plasma surrounding the forward heatshield, there are regions of near thermochemical equilibrium whose properties are predictable - however, there are uncertainties in these electron density calculations necessitating further measurements by H-beta line broadening and holographic interferometer fringe shift as reported here. There is good agreement between the results obtained from the holographic measurements and the spectroscopic measurements which lends confidence to each of the two completely independent diagnostic techniques. The equilibrium electron density determined from the experimental measurements is somewhat higher than that predicted.

Livingston, F. R.↗
NASA NTRS2009

Highly Efficient Design-of-Experiments Methods for Combining CFD Analysis and Experimental Data

It is the purpose of this study to examine the impact of "highly efficient" Design-of-Experiments (DOE) methods for combining sets of CFD generated analysis data with smaller sets of Experimental test data in order to accurately predict performance results where experimental test data were not obtained. The study examines the impact of micro-ramp flow control on the shock wave boundary layer (SWBL) interaction where a complete paired set of data exist from both CFD analysis and Experimental measurements By combining the complete set of CFD analysis data composed of fifteen (15) cases with a smaller subset of experimental test data containing four/five (4/5) cases, compound data sets (CFD/EXP) were generated which allows the prediction of the complete set of Experimental results No statistical difference were found to exist between the combined (CFD/EXP) generated data sets and the complete Experimental data set composed of fifteen (15) cases. The same optimal micro-ramp configuration was obtained using the (CFD/EXP) generated data as obtained with the complete set of Experimental data, and the DOE response surfaces generated by the two data sets were also not statistically different.

Anderson, Bernhard H.↗
NASA NTRS2011

Measurement of Phased Array Point Spread Functions for Use with Beamforming

Microphone arrays can be used to localize and estimate the strengths of acoustic sources present in a region of interest. However, the array measurement of a region, or beam map, is not an accurate representation of the acoustic field in that region. The true acoustic field is convolved with the array s sampling response, or point spread function (PSF). Many techniques exist to remove the PSF's effect on the beam map via deconvolution. Currently these methods use a theoretical estimate of the array point spread function and perhaps account for installation offsets via determination of the microphone locations. This methodology fails to account for any reflections or scattering in the measurement setup and still requires both microphone magnitude and phase calibration, as well as a separate shear layer correction in an open-jet facility. The research presented seeks to investigate direct measurement of the array's PSF using a non-intrusive acoustic point source generated by a pulsed laser system. Experimental PSFs of the array are computed for different conditions to evaluate features such as shift-invariance, shear layers and model presence. Results show that experimental measurements trend with theory with regard to source offset. The source shows expected behavior due to shear layer refraction when observed in a flow, and application of a measured PSF to NACA 0012 aeroacoustic trailing-edge noise data shows a promising alternative to a classic shear layer correction method.

Bahr, Chris↗
NASA NTRS2006

Effect of Counterflow Jet on a Supersonic Reentry Capsule

Recent NASA initiatives for space exploration have reinvigorated research on Apollo-like capsule vehicles. Aerothermodynamic characteristics of these capsule configurations during reentry play a crucial role in the performance and safety of the planetary entry probes and the crew exploration vehicles. At issue are the forebody thermal shield protection and afterbody aeroheating predictions. Due to the lack of flight or wind tunnel measurements at hypersonic speed, design decisions on such vehicles would rely heavily on computational results. Validation of current computational tools against experimental measurement thus becomes one of the most important tasks for general hypersonic research. This paper is focused on time-accurate numerical computations of hypersonic flows over a set of capsule configurations, which employ a counterflow jet to offset the detached bow shock. The accompanying increased shock stand-off distance and modified heat transfer characteristics associated with the counterflow jet may provide guidance for future design of hypersonic reentry capsules. The newly emerged space-time conservation element solution element (CESE) method is used to perform time-accurate, unstructured mesh Navier-Stokes computations for all cases investigated. The results show good agreement between experimental and numerical Schlieren pictures. Surface heat flux and aerodynamic force predictions of the capsule configurations are discussed in detail.

Chang, Chau-Lyan↗
NASA NTRS1994

Reduction of parasitic lasing

A technique was developed which carefully retro-reflects precisely controlled amounts of light back into a laser system thereby intentionally forcing the laser system components to oscillate in a new resonator called the parasitic oscillator. The parasitic oscillator uses the laser system to provide the gain and an external mirror is used to provide the output coupling of the new resonator. Any change of gain or loss inside the new resonator will directly change the lasing threshold of the parasitic oscillator. This change in threshold can be experimentally measured as a change in the absolute value of reflectivity, provided by the external mirror, necessary to achieve lasing in the parasitic oscillator. Discrepancies between experimental data and a parasitic oscillator model are direct evidence of optical misalignment or component performance problems. Any changes in the optical system can instantly be measured as a change in threshold for the parasitic oscillator. This technique also enables aligning the system for maximum parasitic suppression with the system fully operational.

Storm, Mark E.↗
NASA NTRS1972

Bremsstrahlung from cylindrical beta sources.

Refined experimental measurements of the bremsstrahlung number and energy fluxes from thick cylindrical sources of several nuclides are presented, dose rates calculated from experimental energy fluxes are compared with theoretical results based on Wyard's thick-target approximation, and experiments are correlated with both thick- and thin-target bremsstrahlung theory to obtain accurate values of bremsstrahlung yields. The data presented should prove useful for the design of radioisotope power supplies, particularly those used in spacecraft and in biological applications.

Harris, D. W.↗
NASA NTRS1977

Aerodynamic investigation of an air-cooled axial-flow turbine. Part 2: Rotor blade tip-clearance effects on overall turbine performance and internal gas flow conditions: Experimental results and prediction methods

Total turbine blade performance was investigated while changing the blade tip clearance in three ways. The internal flow at the moving blade outlet point was measured. Experimental results were compared with various theoretical methods. Increased blade clearance leads to decreased turbine efficiency.

Yamamoto, A.↗
NASA NTRS2015

Computations of Disturbance Amplification Behind Isolated Roughness Elements and Comparison with Measurements

Computations are performed to study laminar-turbulent transition due to isolated roughness elements in boundary layers at Mach 3.5 and 5.95, with an emphasis on flow configurations for which experimental measurements from low disturbance wind tunnels are available. The Mach 3.5 case corresponds to a roughness element with right-triangle planform with hypotenuse that is inclined at 45 degrees with respect to the oncoming stream, presenting an obstacle with spanwise asymmetry. The Mach 5.95 case corresponds to a circular roughness element along the nozzle wall of the Purdue BAMQT wind tunnel facility. In both cases, the mean flow distortion due to the roughness element is characterized by long-lived streamwise streaks in the roughness wake, which can support instability modes that did not exist in the absence of the roughness element. The linear amplification characteristics of the wake flow are examined towards the eventual goal of developing linear growth correlations for the onset of transition.

Choudhari, Meelan↗
NASA NTRS1984

Elevated temperature crack growth

Critical gas turbine engine hot section components such as blades, vanes, and combustor liners tend to develop minute cracks during early stages of operations. The ability of currently available path-independent (P-I) integrals to correlate fatigue crack propagation under conditions that simulate the turbojet engine combustor liner environment was determined. To date, an appropriate specimen design and a crack displacement measurement method were determined. Alloy 718 was selected as the analog material based on its ability to simulate high temperature behavior at lower temperatures in order to facilitate experimental measurements. Available P-I integrals were reviewed and the best approaches are being programmed into a finite element post processor for eventual comparison with experimental data. The experimental data will include cyclic crack growth tests under thermomechanical conditions, and, additionally, thermal gradients.

Kim, K. S.↗
NASA NTRS1984

Demonstration of a new electrothermal thruster concept

The design and test of a microwave electrothermal thruster are described. The device, which employs a coaxial microwave discharge, was tested in nitrogen gas with 200-600 W of 2.45-GHz input power. Experimental measurements of thrust, specific impulse, and energy efficiency are presented for different flow and discharge pressures. Measured energy efficiencies varied between 30-60 percent and the performance compared favorably with other electrothermal thrusters operating in nitrogen gas. The experimental performance demonstrated the feasibility of the concept.

Whitehair, S.↗
NASA NTRS1984

Experiments with a microwave electrothermal thruster concept

The design and test of two microwave electrothermal thrusters is described. The coaxial and cylindrical cavity concepts are tested in nitrogen gas with 200-2,000 W of 2.45 GHz input power. Experimental measurements and calculations of thrust, specific impulse and energy efficiency are presented for different gas flow rates and discharge pressures. Measured energy efficiencies varied between 10-60 percent and the performance compared favorably with other electrothermal thrusters operating in nitrogen gas. The experimental performance demonstrated the feasibility of the concept.

Asmussen, J.↗
NASA NTRS1987

Carbon monoxide measurements over the eastern Pacific during GTE/CITE 1

As part of the Global Tropospheric Experiment's Chemical Instrumentation Test and Evaluation (GTE/CITE 1) intercomparison, carbon monoxide (CO) measurements were made from the NASA CV-990 aircraft during the fall of 1983 and again in the spring of 1984. The experimental measurements for CO obtained during those flight series over the eastern and mid-Pacific are presented here. Data were acquired from 10 to 20 deg N latitude over the mid-Pacific and from 30 to 37 deg N latitude over the eastern Pacific off the coast of California. A seasonal variation of approximately 34 parts per billion by volume was measured over the altitudes and latitudes sampled, and a small latitudinal variation was also noted. The data are discussed in terms of the meteorological context in which they were collected.

Condon, Estelle P.↗
NASA NTRS1989

Microwave time delays for the dual L-C-band feed system

A new dual-frequency feed system at Goldstone is designed to receive the Phobos spacecraft signal at L-band (1668 + or - 40 MHz) and transmit to the spacecraft at C-band (5008.75 + or - 5.00 MHz) simultaneously. Hence, calculations of the time delay from the C-band range calibration coupler to the phase center of the L-C dual feed and back to the L-band range calibration coupler are required to correct the range measurements. Time delays of the elements in the dual-frequency feed system are obtained mostly from computer calculations and partly from experimental measurements. The method used and results obtained are described.

Chen, J.↗