Search NASA⌕ Search

SEARCH · Search NASA

Results for “inline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Hydrodynamic Analysis of a Suspended Cylinder Under Regular Wave Loading Based on Computational Fluid Dynamics: Preprint

An investigation into the computation of hydrodynamic loads on a suspended cylinder in regular waves is presented. The primary goal was to perform a three-way-validation of the loads between experimental measurements and simulations from two computational methods. Experimental measurements of the longitudinal inline force on a cylinder suspended at a fixed po- sition were available from the Offshore Code Comparison Col- laboration, Continued, with Correlation (OC5) project, Phase Ia. These measurements were compared to Computational Fluid Dynamics (CFD) simulations based on the solution of Reynolds- averaged Navier-Stokes (RANS) equations, as implemented in STAR-CCM plus. The study encompassed a sensitivity analysis of the loads computed in STAR-CCM plus based on wave modeling, boundary conditions, turbulence modeling, and spatial and tem- poral discretization. The analysis was supplemented by results generated with the offshore wind turbine engineering software OpenFAST, based on a hybrid combination of second-order po- tential flow and viscous drag fromMorison's equation. The focus of the investigation was on the assessment of the accuracy of the computation of first- and higher-order hydrodynamic loads. Sub- stantial differences were observed in the numerical prediction of the second and third harmonic force contribution. Local flow field analysis with CFD was applied to study the physics of wave run-up and diffraction dynamics to identify the causes.

16 TIDAL AND WAVE POWER↗

Enterprise: a reduced-scale, flexible fuel, single-cylinder crosshead marine diesel research engine

A custom-built 1/10 scale, flexible-fuel, single-cylinder crosshead marine diesel research engine, dubbed the Enterprise, was designed and built as a platform for conducting marine lubricant research. The engine design was focused on maintaining lubricant boundary conditions similar those of full-scale engines. The Enterprise has a rated speed of 625 rpm to match the linear mean piston speed of full-scale marine engines with the reduced stroke and is capable of 18 bar brake mean effective pressure (BMEP). A high-swirl, uniflow-scavenged, two-stroke combustion system was designed to operate on either distillate diesel or heavy fuel oil (HFO). A hydraulic electronic unit injector (HEUI) fuel injection system with two injectors having customized three-hole nozzles provides fueling and is driven by the MAHLE Flexible ECU (MFE). Intake air boost is provided using a variable speed industrial air compressor along with closed-loop electronically controlled pressure regulation. Exhaust backpressure is also controlled electronically using an electro-pneumatic butterfly valve. A customized, miniaturized Hans Jensen Lubetronic cylinder lubrication system, which is capable of delivering 0.88 mg of cylinder oil per lubricator per injection to the ring pack at up to the maximum engine overspeed rating of 656 rpm, was commissioned for the Enterprise. Four independently temperature-controlled cooling zones are used to provide control of the liner temperature profile. The four coolant zones as well as the system oil and cylinder oil supplies are all controlled within 1°C for consistent thermal boundary conditions. The engine is instrumented with an in-cylinder pressure transducer as well as an inline torque transducer and numerous process temperature and pressure measurements to allow for detailed thermodynamic efficiency analysis, and experimental facilities allow for precise measurement of liner wear and characterization of deposits on the piston and rings. A radio telemetry system from IR Telemetrics is used to measure piston crown temperatures during engine operation. Engine design considerations and experimental facilities are described in detail, along with the results of a study investigating the impact of both system oil and cylinder oil viscosity on friction and efficiency. A test matrix was designed to compare base stock chemistries and viscosities for both system and cylinder oils. Experiments were completed using a fuel economy test protocol that was defined, consisting of repeating six speed/load operating conditions. An automated dynamometer control system was implemented to ensure repeatability of the test procedure. Preliminary testing indicated that the coolant, oil, and exhaust temperatures reach a steady state within 5 minutes of changing operating conditions. The system oil viscosity was found to have a significant impact on friction, with a reduction in viscosity from SAE 30 to SAE 20 resulting in over 6% reduction in friction mean effective pressure (FMEP) and over a 2% reduction in brake-specific fuel consumption (BSFC). Chemistry effects were also evident in the system and cylinder oils. Repeatability comparisons between the individual repetitions of each operating condition were used to ensure that results are statistically valid. For the initial cylinder oil viscosity experiments, observed changes were within the established/normal repeatability; ongoing experiments will determine whether improvements in boundary condition control will enable cylinder friction changes of this magnitude to be measured on this engine platform.

Kaul, Brian↗

Method and apparatus for controlling mass flow rate of recycled anode tail gas in solid oxide fuel cell system

In an SOFC stack system, a reformer supplies reformate to the stack. An anode tail gas portion is recycled into the reformer. An inline flowmeter indicates an apparent recycle flow rate. A map of anode tail gas composition as a function of fuel utilization efficiency U, reformer oxygen/carbon ratio O:C, and recycle percentage R is generated on a laboratory test bed at various recycle rates and fuel utilization rates. Compositions are sent through a flowmeter and a Coriolus mass flowmeter provide a Coriolus flow and sensor voltage function across the various compositions and flow rates to create an average curve and an average (reference) voltage at a given flow. A scale factor Z is calculated and used to determine a scaled sensor voltage X for use in an average flow polynomial curve fit equation to calculate tail gas mass flow rate at any flow value indicated by the flow meter.

30 DIRECT ENERGY CONVERSION↗

Peregrine

The purpose of “Peregrine” is to perform in-situ quality control of the additive manufacturing process in powder bed systems. The software is an AI-based method to automatically detect and map multiple classes of defects present in the top layer of a powder bed system, either after material deposition, i.e. raking, or after printing the layer. Relying on image data or sensing modalities that can be converted into image data, the code allows for: (1) various steps of pre-processing of the data (registration, distortion correction, etc), (2) annotation of training datasets, (3) processing of data inline or offline, (4) creating 3D rendering of the defect map, and (5) implementation of corrective actions if allowed by the manufacturing platform.

Paquit, Vincent C↗

Transparent bridge for monitoring crypto-partitioned wide-area network

This disclosure is directed to monitoring a crypto-partitioned, or cipher-text, wide-area network (WAN). A first computing device may be situated in a plain-text portion of a first enclave behind a first inline network encryptor (INE). A second device may be positioned in a plain-text portion of a second enclave behind a second INE. The two enclaves may be separated by a cipher-text WAN, over which the two enclaved may communicate. The first computing device may receive a data packet from the second computing device. The first computing device may then determine contents of a header of the data packet. The first computing device may, based at least in part on the contents of the header of the data packet, determine a status of the cipher-text WAN.

97 MATHEMATICS AND COMPUTING↗

DENOVA: Deduplication Extended NOVA File System

This paper shows mathematically and experimentally that inline deduplication is not suitable for file systems on ultra-low latency Intel Optane DC PM devices in terms of performance, and proposes DeNova, an offline deduplication specially designed for log-structured NVM file systems such as NOVA. DeNova offers high-performance and low-latency I/O processing and executes deduplication in the background without interfering with foreground I/Os. DeNova employs DRAM-free persistent deduplication metadata, favoring CPU cache line, and ensures failure consistency on any system failure. We implement DeNova in the NOVA file system. Evaluation with DeNova confirms a negligible performance drop of baseline NOVA of less than 1%, while gaining high storage space savings. Extensive experiments show DeNova is failure consistent in all failure scenario cases.

Khan, Awais↗

In-line mixing printhead for multimaterial aerosol jet printing

An aerosol jet printhead comprising an in-line static mixer can mix multiple aerosol streams for co-deposition from a single nozzle. A printhead was designed, fabricated, and tested, demonstrating in-plane functionally graded films. The inline mixing printhead can be used with a compact aerosol jet deposition system.

Secor, Ethan Benjamin↗

Transparent bridge for monitoring crypto-partitioned wide-area network

This disclosure is directed to monitoring a crypto-partitioned, or cipher-text, wide-area network (WAN). A first computing device may be situated in a plain-text portion of a first enclave behind a first inline network encryptor (INE). A second device may be positioned in a plain-text portion of a second enclave behind a second INE. The two enclaves may be separated by a cipher-text WAN, over which the two enclaved may communicate. The first computing device may receive a data packet from the second computing device. The first computing device may then determine contents of a header of the data packet. The first computing device may, based at least in part on the contents of the header of the data packet, determine a status of the cipher-text WAN.

Ramanujan, Ranga↗

Method of making a photovoltaic device on a substrate at high speed with perovskite solution

A continuous inline method for production of photovoltaic devices at high speed includes: providing a substrate; depositing a first carrier transport solution layer with a first carrier transport deposition device to form a first carrier transport layer on the substrate; depositing a Perovskite solution comprising solvent and perovskite precursor materials with a Perovskite solution deposition device on the first carrier transport layer; drying the deposited Perovskite solution to form a Perovskite absorber layer; and depositing a second carrier transport solution with a second carrier transport deposition device to form a second carrier transport layer on the Perovskite absorber layer, wherein the deposited Perovskite solution is dried at least partially with a fast drying device which causes a conversion reaction and the Perovskite solution to change in optical density by at least a factor of 2 in less than 0.5 seconds after the fast drying device first acts on the Perovskite solution.

Christensen, Scott Kenneth↗

Mooring System Cost Estimates for Wave Energy Farms in Shared Mooring Arrays

As wave energy converters (WECs) become more advanced and cost-efficient, so too must their mooring systems. A key question in the development plans for WECs is the cost of the mooring system, particularly for large wave farms. WEC devices deployed in a WEC farm array, where each device can be connected by shared mooring lines in various array layouts, have potential to reduce mooring system costs significantly. This paper presents the modeling and designing of mooring systems for large WEC arrays and the calculation of the cost of each mooring system to determine the change in cost as the number of WECs in a farm increases. A baseline mooring system for a single floating oscillating water column (OWC) WEC was developed for this analysis. The mooring system utilizes four anchored mooring lines connected to a square assembly of wire rope mooring lines, supported by four floating buoys, and attached to the floating WEC by four polyester rope mooring lines. This assembly, referred to as a floating cell, can be tiled to form various rectangular WEC arrays. The objective of this analysis is to determine how the mooring system cost changes as more WECs are added to an array layout, each with their own interconnected floating cell. To do this, complete mooring systems need to be designed for each WEC array layout. To narrow down the design space of a WEC array mooring system, a couple assumptions were made. It was assumed that the floating cell parameters of the baseline design were to stay constant across all floating cells in the WEC array. It was also assumed that the anchored mooring lines would be of the baseline configuration, a predominantly chain mooring line with a short section of polyester rope near the fairlead, and a drag-embedment anchor. These anchored lines were assumed to extend from the outer edges of the WEC array, inline with the headings of the wire rope mooring lines of the floating cells, or diagonal if extending from a corner of the WEC array. Full mooring systems were designed for 2xN and NxN WEC array layouts and efficiently simulated in the mooring dynamics simulation tool, MoorDyn, to ensure all dynamic constraints were met. The system costs were calculated and then refined by shortening unnecessary chain line lengths and reducing the chain diameters of the downstream anchored mooring lines. It was found that, in general, mooring system costs per WEC decrease when WECs are installed in an array. Compared to the baseline mooring system for a single WEC, the 2x3 mooring system array had the lowest mooring system cost per WEC, reducing the cost per WEC by 59%. The 3x3 and 4x4 array mooring systems also saw significant reductions in cost per WEC but had negligible cost savings between the two designs, primarily because the larger 4x4 mooring system requires larger chain diameters, which increases cost. These results provide an interesting glimpse into modeling, designing, and calculating the cost of mooring systems for large WEC arrays.

cost↗

DenKv: Addressing Design Trade-offs of Key-value Stores for Scientific Applications

High-performance computing (HPC) facilities have employed flash-based storage tier near to compute nodes to absorb high I/O demand by HPC applications during periodic system-level checkpoints. To accelerate these checkpoints, proxy-based distributed key-value stores (PD-KVS) gained particular attention for their flexibility to support multiple backends and different network configurations. PD-KVS rely internally on monolithic KVS, such as LevelDB or RocksDB, to exploit the KV interface and query support. However, PD-KVS are unaware of the high redundancy factor in checkpoint data, which can be up to GBs to TBs, and therefore, tend to generate high write and space amplification on these storage layers. In this paper, we propose DenKv which is deduplication-extended node-local LSM-tree-based KVS. DenKv employs asynchronous partially inline dedup (APID) and aims to maintain the performance characteristics of LSM-tree-based KVS while reducing the write and space amplification problems. We implemented DenKv atop BlobDB and showed that our proposed solution maintains performance while reducing write amplification up to 2× and space amplification by 4× on average.

Khan, Awais↗

Movable geometry and eigenvalue search capability in the MC21 Monte Carlo code

A description of a robust and flexible movable geometry implementation in the Monte Carlo code MC21 is described along with a search algorithm that can be used in conjunction with the movable geometry capability to perform eigenvalue searches based on the position of some geometric component. The natural use of the combined movement and search capability is searching to critical through variation of control rod (or control drum) position. The movable geometry discussion provides the mathematical framework for moving surfaces in the MC21 combinatorial solid geometry description. A discussion of the interface between the movable geometry system and the user is also described, particularly the ability to create a hierarchy of movable groups. Combined with the hierarchical geometry description in MC21 the movable group framework provides a very powerful system for inline geometry modification. The eigenvalue search algorithm implemented in MC21 is also described. The foundations of this algorithm are a regula falsi search though several considerations are made in an effort to increase the efficiency of the algorithm for use with Monte Carlo. Specifically, criteria are developed to determine after each batch whether the Monte Carlo calculation should be continued, the search iteration can be rejected, or the search iteration has converged. These criteria seek to minimize the amount of time spent per iteration. Results for the regula falsi method are shown, illustrating that the method as implemented is indeed convergent and that the optimizations made ultimately reduce the total computational expense. (authors)

97 MATHEMATICS AND COMPUTING↗

Transparent bridge for monitoring crypto-partitioned wide-area network

This disclosure is directed to monitoring a crypto-partitioned, or cipher-text, wide-area network (WAN). A first computing device may be situated in a plain-text portion of a first enclave behind a first inline network encryptor (INE). A second device may be positioned in a plain-text portion of a second enclave behind a second INE. The two enclaves may be separated by a cipher-text WAN, over which the two enclaved may communicate. The first computing device may receive a data packet from the second computing device. The first computing device may then determine contents of a header of the data packet. The first computing device may, based at least in part on the contents of the header of the data packet, determine a status of the cipher-text WAN.

97 MATHEMATICS AND COMPUTING↗

Methods of making lithium ion conducting sulfide glass

A lithium ion-conductive solid electrolyte including a freestanding inorganic vitreous sheet of sulfide-based lithium ion conducting glass is capable of high performance in a lithium metal battery. Such an electrolyte is also manufacturable, and readily adaptable for battery cell and cell component manufacture, in a cost-effective, scalable manner using an automated machine based system, apparatus and methods based on inline spectrophotometry to assess and inspect the quality of such vitreous solid electrolyte sheets and associated components. Suitable manufacturing methods can involve providing a sulfur precursor, providing a boron precursor material having lithium as a second constituent, combining the sulfur and boron precursor materials to form a precursor mixture, melting the mixture, and cooling the melt to form a solid lithium ion conducting glass. The glass may have a Li+ conductivity of at least 10 −5 S/cm. The boron precursor material may be synthesized by reducing boron oxide to boron metal by heating the boron oxide in direct contact with lithium metal.

Visco, Steven J.↗

Systems and methods for monitoring fuel cell membrane degradation

Systems and methods for real-time continuous monitoring of fuel cell membrane degradation are provided. At least one microsensor can be used as an inline sensor integrated at the cathode exhaust and/or the anode exhaust of a fuel cell, such as a proton exchange membrane fuel cell (PEMFC)). The microsensor can monitor the PEMFC degradation status by sensing the emission of fluoride.

Dong, Dongmei↗

Ultra-Long Distance BOTDA Sensor System Employing Hybrid Amplification and Advanced Noise Reduction Techniques

Brillouin Optical Time Domain Analysis (BOTDA) sensor systems play a pivotal role in distributed sensing, which enables precise measurements of strain and temperature across extensive fiber lengths. This research offers a comprehensive strategy to extend the sensing range of BOTDA systems beyond tens of kilometers while maintaining high spatial resolutions. Such enhanced sensing is realized through the integration of distributed Raman amplification, inline amplification using erbium-doped fiber amplifiers (EDFA), and advanced noise reduction techniques. Optimizing Raman pump and probe wave profiles ensures the robustness of Brillouin scattering signals, effectively countering attenuation-induced losses. Additionally, enhancing weak Brillouin signals by strategically placing EDFAs at optimal fiber locations keeps sensor sensitivity high. Leveraging inherent redundancy in measured data as a function of frequency and fiber distance, the non-local means (NLM) filter removes noise while preserving essential physical information. In summary, this research has shown a holistic exploration of extending BOTDA’s distance sensing capabilities up to 150 km with spatial resolutions of 8 meters.

Bhatta, Hari↗

Epoxy-based infrared filter assembly and associated fabrication devices and method

Epoxy-based inline infrared (IR) filter assembly, and manufacture and use of the same. Co-axial infrared filter assemblies comprise a substantially cylindrical filter body forming a central cavity characterized by opposing holes at each end. The filter body forms an outer conductor, and SMA connectors coupled to the opposing holes at each end of the body are electrically coupled to form an inner conductor positioned along a long axis of the filter body. An infrared absorbing material (such as castable epoxy resin) fills the central cavity of the filter body. Methods for producing the co-axial infrared filter include pressing SMA connectors into the respective ends of the filter body, electrically coupling the SMA connectors, and filling the filter body with epoxy. Electronic systems for operating a dark matter detector include a feedline comprising a coaxial filter configured to advantageously block infrared noise.

Spahn, Gabriel↗

Systems and methods for monitoring fuel cell membrane degradation

Systems and methods for real-time continuous monitoring of fuel cell membrane degradation are provided. At least one microsensor can be used as an inline sensor integrated at the cathode exhaust and/or the anode exhaust of a fuel cell, such as a proton exchange membrane fuel cell (PEMFC)). The microsensor can monitor the PEMFC degradation status by sensing the emission of fluoride.

Dong, Dongmei↗