Search NASA⌕ Search

SEARCH · Search NASA

Results for “low viscosity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

When does small-scale convection begin beneath oceanic lithosphere?

A numerical model of small-scale convection in a fluid of variable viscosity is described. The results indicate that recently observed gravity anomalies showing a pattern of highs and lows aligned in the direction of oceanic plate motion may be the result of small-scale mantle flow. The convective flow must begin in the first six Myr of lithospheric cooling to produce the observed signals, which is not inconsistent with constraints on the viscosity of the mantle. The calculated trend for the subsidence of the ocean floor is found to be almost linear with the square root of time even when small-scale convection has significantly changed the rate of subsidence. For average shallow asthenospheric viscosities of about 10 to the 18th Pa/s, the model subsidence can match data for the oceans and reproduce the magnitude and wavelength of the observed gravity anomalies.

Buck, W. R.↗
NASA NTRS1995

Time-domain approach for the transient responses in stratified viscoelastic Earth models

We have developed the numerical algorithm for the computation of transient viscoelastic responses in the time domain for a radially stratified Earth model. Stratifications in both the elastic parameters and the viscosity profile have been considered. The particular viscosity profile employed has a viscosity maximum with a constrast of O(100) in the mid lower mantle. The distribution of relaxation times reveals the presence of a continuous spectrum situated between O(100) and O(exp 4) years. The principal mode is embedded within this continuous spectrum. From this initial-value approach we have found that for the low degree harmonics the non-modal contributions are comparable to the modal contributions. For this viscosity model the differences between the time-domain and normal-mode results are found to decrease strongly with increasing angular order. These calculations also show that a time-dependent effective relaxation time can be defined, which can be bounded by the relaxation times of the principal modes.

Hanyk, L.↗
NASA NTRS1978

Solventless LARC-160 Polyimide Matrix Resin

The addition polyimide, LARC-160, which was originally synthesized from low cost liquid monomers as a laminating resin in ethanol, was prepared as a solventless, high viscosity, neat liquid resin. The resin was processed by hot-melt coating techniques into graphite prepreg with excellent tack and drape. Comparable data on graphite reinforced laminates made from solvent-coated and various hot-melt coated prepreg were generated. LARC-160, because of its liquid nature, can be easily autoclave processed to produce low void laminates. Liquid chromatographic fingerprints indicate good reaction control on resin scale ups. Minor changes in monomer ratios were also made to improve the thermal aging performance of graphite laminates.

Stclair, T. L.↗
NASA NTRS1988

The development of new, low-cost perfluoroalkylether fluids with excellent low and high-temperature properties

A series of perfluoroalkylether (PFAE) fluids were synthesized by direct fluorination. Viscosity-temperature properties, oxidation stabilities, oxidation-corrosion properties, and lubricity were determined. The fluids were tested in the presence of common elastomers to check for compatibility. The bulk modulus of each was measured to determine if any could be used as nonflammable aircraft hydraulic fluid. It was determined that as the carbon to oxygen ratio decreases, the viscometric properties improve, the fluids may become poor lubricants, the bulk modulus increases, the surface tension increases, and the fluid density increases. The presence of difluoromethylene oxide units in the polymer does not seriously lower the oxidation and oxidation-corrosion stabilities as long as the difluoromethylene oxide units are separated by other units.

Bierschenk, Thomas R.↗
NASA NTRS1994

Low-frequency quasi-periodic oscillations in low-mass X-ray binaries and galactic black hole candidates

We consider the inner regions of accretion disks surrounding black holes and neutron stars and investigate the nonlinear time-dependent evolution of thermal-viscous instabilities. The viscous stress is assumed to be proportional to the gas pressure with the viscosity parameter formulated as alpha = min alpha (sub zero) (h/r) (exp n), alpha(sub max), where h is the local scale height, r is the distance from the central compact object, and n, alpha(sub zero) and alpha(sub max) are constants. It is found that the disk is unstable for alpha sufficiently sensitive to h (n greater than or equal to 1.2). The instabilities are globally coherent in the entire unstable region of the disk, and, depeding on the viscosity parameters, the time variability of the mass accretion rates are manifested as periodic or quasi-periodic oscillations. We show that, the low-frequency (approximately 0.04 Hz) quasi-periodic oscillations (QPOs) discovered recently in some of the black hole candidates (Cyg X-1 and GRO J0422+32) and a low-mass X-ray binary (Rapid Burster MXB 1730-335) may be explicable by the thermal-viscous instabilities in accretion disks. The observations of QPOs place constraints on the viscosity parameters and suggest that (n, alpha(sub zero) approximately (1.6, 30) for the Rapid Burster with a 1.4 solar mass neutron star. In the case of black hole candidates, the dependence of alpha on h/r is less steep corresponding to n approximately 1.2-1.3 for black holes less than 10 solar mass.

Chen, Xingming↗
NASA NTRS1976

Reduction of losses in low-frequency /2 MHz/ surface-wave delay line by outgassing

Surface waves are attenuated by a fluid or gas surrounding the surface of propagation, an effect caused by frictional losses determined by the fluid or gas viscosity and by the emission of compression waves into the environment. The paper reports a large reversible reduction in attenuation of surface waves at frequencies as low as 2 MHz by outgassing treatments of some materials, suggesting that at such frequencies vacuum encapsulation is a desirable procedure. Outgassing experiments were performed on a delay line constructed from high-density p.z.t.-8 (lead-zirconate-titanate). The delay line configuration was a slab waxed onto a metal base with coaxial connectors mounted near and connected by gold-wire leads to the interdigital finger sets. Output signal enhancements by as much as 8 dB were achieved after overnight evacuation at 10 to the -2 torr at room temperature.

Tittmann, B. R.↗
NASA NTRS1984

The effects of the variations in sea surface temperature and atmospheric stability in the estimation of average wind speed by SEASAT-SASS

The average wind speeds from the scatterometer (SASS) on the ocean observing satellite SEASAT are found to be generally higher than the average wind speeds from ship reports. In this study, two factors, sea surface temperature and atmospheric stability, are identified which affect microwave scatter and, therefore, wave development. The problem of relating satellite observations to a fictitious quantity, such as the neutral wind, that has to be derived from in situ observations with models is examined. The study also demonstrates the dependence of SASS winds on sea surface temperature at low wind speeds, possibly due to temperature-dependent factors, such as water viscosity, which affect wave development.

Liu, W. T.↗
NASA NTRS1985

Critical Transport Phenomena in Fluid Helium Under Low Gravity

The feasibility of carrying out measurements of certain critical transport properties of pure fluid under conditions of low gravity was studied. These properties are the thermal conductivity, kappa, the shear viscosity zeta and the diffusive relaxation time tau, which are predicted to diverge (tend to infinity) as the liquid-vapor critical point is approached. However, in this critical region, the Earth's gravity effect becomes very important. As the critical point is approached, the gravity effects increasingly distort the results. The reason for this is that the compressibility of the fluid also diverges and under the influence of gravity causes a vertical density gradient in the fluid, which is significant even when very thin fluid layers (typically 1 mm high) are being used. The result is that the temperature dependence of kappa, zeta, and tau tends to flatten off as T sub c is approached instead of continuing to increase, and therefore the predictions from the renormalization group and mode coupling theories cannot be subjected to a satisfactory test.

Meyer, H.↗
NASA NTRS1995

Advanced k-epsilon modeling of heat transfer

This report describes two approaches to low Reynolds-number k-epsilon turbulence modeling which formulate the eddy viscosity on the wall-normal component of turbulence and a length scale. The wall-normal component of turbulence is computed via integration of the energy spectrum based on the local dissipation rate and is bounded by the isotropic condition. The models account for the anisotropy of the dissipation and the reduced mixing length due to the high strain rates present in the near-wall region. The turbulent kinetic energy and its dissipation rate were computed from the k and epsilon transport equations of Durbin. The models were tested for a wide range of turbulent flows and proved to be superior to other k-epsilon models, especially for nonequilibrium anisotropic flows. For the prediction of airfoil heat transfer, the models included a set of empirical correlations for predicting laminar-turbulent transition and laminar heat transfer augmentation due to the presence of freestream turbulence. The predictions of surface heat transfer were generally satisfactory.

Kwon, Okey↗
NASA NTRS2007

Oil-Free Rotor Support Technologies for an Optimized Helicopter Propulsion System

An optimized rotorcraft propulsion system incorporating a foil air bearing supported Oil-Free engine coupled to a high power density gearbox using high viscosity gear oil is explored. Foil air bearings have adequate load capacity and temperature capability for the highspeed gas generator shaft of a rotorcraft engine. Managing the axial loads of the power turbine shaft (low speed spool) will likely require thrust load support from the gearbox through a suitable coupling or other design. Employing specially formulated, high viscosity gear oil for the transmission can yield significant improvements (approx. 2X) in allowable gear loading. Though a completely new propulsion system design is needed to implement such a system, improved performance is possible.

DellaCorte, Christopher↗
NASA NTRS2016

Water in the Cratonic Mantle Lithosphere

The fact that Archean and Proterozoic cratons are underlain by the thickest (>200 km) lithosphere on Earth has always puzzled scientists because the dynamic convection of the surrounding asthenosphere would be expected to delaminate and erode these mantle lithospheric "keels" over time. Although density and temperature of the cratonic lithosphere certainly play a role in its strength and longevity, the role of water has only been recently addressed with data on actual mantle samples. Water in mantle lithologies (primarily peridotites and pyroxenites) is mainly stored in nominally anhydrous minerals (olivine, pyroxene, garnet) where it is incorporated as hydrogen bonded to structural oxygen in lattice defects. The property of hydrolytic weakening of olivine [4] has generated the hypothesis that olivine, the main mineral of the upper mantle, may be dehydrated in cratonic mantle lithospheres, contributing to its strength. This presentation will review the distribution of water concentrations in four cratonic lithospheres. The distribution of water contents in olivine from peridotite xenoliths found in kimberlites is different in each craton (Figure 1). The range of water contents of olivine, pyroxene and garnet at each xenolith location appears linked to local metasomatic events, some of which occurred later then the Archean and Proterozoic when these peridotites initially formed via melting. Although the low olivine water contents (<10 ppm wt H2O) at > 6 GPa at the base of the Kaapvaal cratonic lithosphere may contribute to its strength, and prevent its delamination, the wide range of those from Siberian xenoliths is not compatible with providing a high enough viscosity contrast with the asthenophere. The water content in olivine inclusions from Siberian diamonds, on the other hand, have systematically low water contents (<20 ppm wt H2O). The xenoliths may represent a biased sample of the cratonic lithosphere with an over-­abundance of metasomatized peridotites with high water contents. The olivine inclusions, however, may have been protected from metasomatism by their host diamond and record the overall low olivine water content of the cratonic lithosphere. Water may thus still play a role in cratonic keel longevity.

Peslier, A. H.↗
NASA NTRS1986

Computer simulation of immobilized pH gradients at acidic and alkaline extremes - A quest for extended pH intervals

Computer simulations of the concentration profiles of simple biprotic ampholytes with Delta pKs 1, 2, and 3, on immobilized pH gradients (IPG) at extreme pH values (pH 3-4 and pH 10-11) show markedly skewed steady-state profiles with increasing kurtosis at higher Delta pK values. Across neutrality, all the peaks are symmetric irrespective of their Delta pK values, but they show very high contribution to the conductivity of the background gel and significant alteration of the local buffering capacity. The problems of skewness, due to the exponential conductivity profiles at low and high pHs, and of gel burning due to a strong electroosmotic flow generated by the net charges in the gel matrix, also at low and high pHs, are solved by incorporating in the IPG gel a strong viscosity gradient. This is generated by a gradient of linear polyacrylamide which is trapped in the gel by the polymerization process.

Mosher, Richard A.↗
NASA NTRS1988

Directional solidification of Al-Ni/SiC composites during parabolic trajectories

Aluminum-6.1 wt. pct. nickel-silicon carbide composites containing varying volume fractions and particle sizes of SiC were directionally solidified at different translation rates and temperature gradients, under variable gravity levels. High-gravity, high-volume fractions of particles or high effective viscosity of liquid favored the engulfment of particles by the melt interface. Solidification under low gravity seemed to deflocculate the SiC particle agglomerates, while opposite results were obtained when solidifying under high gravity. Intercellular spacings were higher under low gravity solidfication.

Dhindaw, B. K.↗
NASA NTRS1989

Better PFAE's From Direct Fluorination

New low-molecular-weight perfluoroalkylethers (PFAE's) synthesized by direct fluorination in experimental study. Correlated viscosity and oxidation characteristics of PFAE's with structures to evaluate suitability as high-temperature lubricants and hydraulic fluids. Direct fluorination process attractive because it often involves single-step reaction and uses cheap starting materials. Versatile: produces highly branched ethers as well as polyethers containing more than two sequential carbon atoms in polymer chains. Such molecules cannot be made by conventional techniques.

Jones, W. R., Jr.↗
NASA NTRS1991

On the interaction between first- and second-mode waves in a supersonic boundary layer

Linear stability theory predicts two or more types of unstable disturbances in a sufficiently high-speed boundary layer. These include the first mode, which is similar to the Tollmien-Schlichting waves found in low-speed flows, and the second mode, which does not depend strongly on the viscosity. Generally, the most unstable first mode is three-dimensional while the most unstable second mode is two-dimensional. The interaction between these two spatially unstable modes are studied by direct solution of the three-dimensional Navier-Stokes equations. It is found that the two-dimensional second mode causes a significant increase in the nonlinearity and in the three-dimensionality of the flowfield. The results suggest that this interaction may accelerate transition for flows where the second mode has a significant growth rate.

Maestrello, L.↗
NASA NTRS1994

Coronal heating by the resonant absorption of Alfven waves: The effect of viscous stress tensor

The time-dependent linearized magnetohydrodynamics (MHD) equations for a fully compressible, low-beta, viscoresistive plasma are solved numerically using an implicit integration scheme. The full viscosity stress tensor (Braginskii 1965) is included with the five parameters eta(sub i) i = 0 to 4. In agreement with previous studies, the numerical simulations demonstrate that the dissipation on inhomogeneities in the background Alfven speed occurs in a narrow resonant layer. For an active region in the solar corona the values of eta(sub i) are eta(sub o) = 0.65 g/cm/s, eta(sub 1) = 3.7 x 10(exp -12) g/cm/s, eta(sub 2) = 4 eta(sub 1), eta(sub 3) = 1.4 x 10(exp -6) g/cm/s, eta(sub 4) = 2 eta(sub 3), with n = 10(exp 10)/cu cm, T = 2 x 10(exp 6) K, and B = 100 G. When the Lundquist number S = 10(exp 4) and R(sub 1) much greater than S (where R(sub 1) is the dimensionless shear viscous number) the width of the resistive dissipation layer d(sub r) is 0.22a (where a is the density gradient length scale) and d(sub r) approximately S(exp -1/3). When S much greater than R(sub 1) the shear viscous dissipation layer width d(sub r) scales as R(sub 1)(exp -1/3). The shear viscous and the resistive dissipation occurs in an overlapping narrow region, and the total heating rate is independent of the value of the dissipation parameters in agreement with previous studies. Consequently, the maximum values of the perpendicular velocity and perpendicular magnetic field scale as R(sub 1)(exp -1/3). It is evident from the simulations that for solar parameters the heating due to the compressive viscosity (R(sub 0) = 560) is negligible compared to the resistive and the shear viscous (R(sub 1)) dissipation and it occurs in a broad layer of order a in width. In the solar corona with S approximately equals 10(exp 4) and R(sub 1) approximately equals 10(exp 14) (as calculated from the Braginskii expressions), the shear viscous resonant heating is of comparable magnitude to the resistive resonant heating.

Ofman, L.↗