Results for “mechanical failure” — Page 21

NASA NTRS1980

Study of intermittent field hardware failure data in digital electronics

The collection and analysis of data concerning intermittent dailures in digital devices was performed using data from a computer design for shipboard usage. The failure data consisted of actual field failures classified by failure mechanisms and their likelihood of having been intermittent, potentially intermittent, or hard. Each class was studies with respect to computer operation in the ranges of 0 to 2,000 hours, 0 to 5, hours, and 0 to 10,000 hours. The study was done at the computer level as well as the microcircuit level. Results indicate that as age increases, the quasi-intermittent failure rate increases and the mean time to failure descreases.

Oneill, E. J.↗

NASA NTRS2010

Characteristics of Whipple Shield Performance in the Shatter Regime

Ballistic limit equations define the failure of metallic Whipple shields in three parts: low velocity, shatter, and hypervelocity. Failure limits in the shatter regime are based on a linear interpolation between the onset of projectile fragmentation, and impulsive rupture of the shield rear wall. A series of hypervelocity impact tests have been performed on aluminum alloy Whipple shields to investigate failure mechanisms and performance limits in the shatter regime. Test results demonstrated a more rapid increase in performance than predicted by the latest iteration of the JSC Whipple shield BLE following the onset of projectile fragmentation. This increase in performance was found to level out between 4.0-5.0 km/s, with a subsequent decrease in performance for velocities up to 6.0 km/s. For a detached spall failure criterion, the failure limit was found to continually decrease up to a velocity of 7.0 km/s, substantially varying from the BLE, while for perforation-based failure an increase in performance was observed. An existing phenomenological ballistic limit curve was found to provide a more accurate reproduction of shield behavior that the BLE, however a number of underlying assumptions such as the occurrence of complete projectile fragmentation and the effect on performance of incipient projectile melt were found to be inaccurate. A cratering relationship based on the largest residual fragment size has been derived for application at velocities between 3.0-4.0 km/s, and was shown to accurately reproduce the trends of the experimental data. Further investigation is required to allow a full analytical description of shatter regime performance for metallic Whipple shields.

Ryan, S.↗

NASA NTRS1976

Bibliography of information on mechanics of structural failure (hydrogen embrittlement, protective coatings, composite materials, NDE)

This bibliography is comprised of approximately 1,600 reference citations related to four problem areas in the mechanics of failure in aerospace structures. The bibliography represents a search of the literature published in the period 1962-1976, the effort being largely limited to documents published in the United States. Listings are subdivided into the four problem areas: Hydrogen Embrittlement; Protective Coatings; Composite Materials; and Nondestructive Evaluation. An author index is included.

Carpenter, J. L., Jr.↗

NASA NTRS1989

A study of graphite-epoxy laminate failures due to high transverse shear strains using the multi-span-beam shear test procedure

The multi-span-beam shear test procedure is used to study failure mechanisms in graphite-epoxy laminates due to high transverse shear strains induced by severe local bending deformations in test specimens. Results of a series of tests on specimens with a variety of stacking sequences, including some with adhesive interleaving, are presented. These results indicate that laminates with stacking sequences with several + or - 45 and 90 deg plies next to each other are more susceptible to failures due to high transverse shear strains than laminates with + or - 45 and 0 deg plies next to each other or with + or - 45 deg plies next to layers of adhesive interleaving. Results of these tests are compared with analytical results based on finite elements.

Jegley, Dawn C.↗

NASA NTRSDate not supplied

Advancing Metasurfaces Towards New Frontiers: Nonvolatile Reconfigurable Optics

The applications of adaptive optics extend across multiple sectors, encompassing areas such as LiDAR, biological and chemical sensing, and free-space communications. In this study, we report on the design, fabrication, testing, and modeling of electrically reconfigurable metasurfaces using a low-loss high contrast phase change material, Ge2Sb2Se4Te integrated with an IR-transparent silicon microheater. Through this work, we introduce a reliable architecture for switching PCM-based metasurfaces within an integrated circuit configuration which is compatible with standard foundry fabrication processes. We demonstrate the capability of controlling the transmission of electromagnetic waves through the precise stimulation of PCM-based pixels, each spanning a few hundred microns, over numerous cycles. By leveraging PCM-based pixels, we unlock the potential to create metasurfaces encompassing a diverse range of functionalities such as dielectric filters, metalens, or beam steering devices, which is governed by the design of the meta-atoms. Further, we perform an in-depth investigation into the failure mechanism utilizing techniques such as Fourier transform IR spectroscopy (FTIR), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and thermal modeling. According to our results, due to a sharp temperature rise at the PCM/heater interface, we observe severe delamination of the PCM from the heater. More uniform PCM deposition, better adhesion at the PCM/heater interface, and a more uniform temperature distribution in the device could potentially mitigate the failure and lead to a longer life-time. By addressing these challenges, we aim to unlock the full potential of PCM-based devices and advance the field of adaptive optics.

Phase change material↗

NASA NTRS2001

Effect of Load Rate on Ultimate Tensile Strength of Ceramic Matrix Composites at Elevated Temperatures

The strengths of three continuous fiber-reinforced ceramic composites, including SiC/CAS-II, SiC/MAS-5 and SiC/SiC, were determined as a function of test rate in air at 1100 to 1200 C. All three composite materials exhibited a strong dependency of strength on test rate, similar to the behavior observed in many advanced monolithic ceramics at elevated temperatures. The application of the preloading technique as well as the prediction of life from one loading configuration (constant stress-rate) to another (constant stress loading) suggested that the overall macroscopic failure mechanism of the composites would be the one governed by a power-law type of damage evolution/accumulation, analogous to slow crack growth commonly observed in advanced monolithic ceramics. It was further found that constant stress-rate testing could be used as an alternative to life prediction test methodology even for composite materials, at least for short range of lifetimes and when ultimate strength is used as the failure criterion.

Choi, Sung R.↗

NASA NTRS2011

Approaches for Tensile Testing of Braided Composites

For angleply composites, lamina tension and compression strengths are commonly determined by applying classical lamination theory to test data obtained from testing of angleply composite specimens. For textile composites such as 2D triaxial braids, analysis is more complex and standard test methods do not always yield reliable strength measurements. This paper describes recent research focused on development of more reliable tensile test methods for braided composites and presents preliminary data for various approaches. The materials investigated in this work have 0deg+/-60 2D triaxial braid architecture with nearly equal fiber volume fraction in each of the three fiber directions. Flat composite panels are fabricated by resin transfer molding (RTM) using six layers of the braided preform aligned along the 0deg fiber direction. Various epoxy resins are used as matrix materials. Single layer panels are also fabricated in order to examine local variations in deformation related to the braid architecture. Specimens are cut from these panels in the shape of standard straight-sided coupons, an alternative bowtie geometry, and an alternative notched geometry. Axial tensile properties are measured using specimens loaded along the 0deg fiber direction. Transverse tensile properties are measured using specimens loaded perpendicular to the 0deg fibers. Composite tubes are also fabricated by RTM. These tubes are tested by internal pressurization using a soft rubbery material sealed between the inside diameter of the tube and the load fixtures. The ends of the tube are unconstrained, so the primary load is in the hoop direction. Tubes are fabricated with the 0deg fibers aligned along the tube axis by overbraiding the preform on a mandrel. Since the loading is in the hoop direction, testing of the overbraided tube provides a measure of transverse tensile strength. Previous work has indicated that straight-sided coupons yield a transverse tensile strength that is much lower than the expected material strength because of premature edge-initiated failure. Full-field strain measured during transverse tensile tests clearly showed accumulation of edge damage prior to failure. In the current work, high speed video and testing of single layer specimens are used to investigate potential failure mechanisms in more detail. High speed video clearly shows the edge initiation in six layer transverse tensile test coupons. Specimens with the bowtie geometry and the notched geometry minimize this edge effect and yield significantly higher transverse tensile strength values compared to the straight-sided coupons. However, bowtie and notched specimens geometries are not ideal because of the non-uniform stress and strain fields in the region of failure. Testing of tubes using internal pressurization eliminates edge-initiated failure and provides a more uniform state of stress and strain. Preliminary results indicate that bowtie, notched, and tube specimens yield comparable values for transverse tensile strength and that these values are much higher than the strength measured using a straight-sided coupon.

Roberts, Gary D.↗

NASA NTRS1994

An analytical and experimental investigation of the response of the curved, composite frame/skin specimens

Six-foot diameter, semicircular graphite/epoxy specimens representative of generic aircraft frames were loaded quasi-statistically to determine their load response and failure mechanisms for large deflections that occur in airplanes crashes. These frame/skin specimens consisted of a cylindrical skin section co-cured with a semicircular I-frame. The skin provided the necessary lateral stiffness to keep deformations in the plane of the frame in order to realistically represent deformations as they occur in actual fuselage structures. Various frame laminate stacking sequences and geometries were evaluated by statically loading the specimen until multiple failures occurred. Two analytical methods were compared for modeling the frame/skin specimens: a two-dimensional shell finite element analysis and a one-dimensional, closed-form, curved beam solution derived using an energy method. Flange effectivities were included in the beam analysis to account for the curling phenomenon that occurs in thin flanges of curved beams. Good correlation was obtained between experimental results and the analytical predictions of the linear response of the frames prior to the initial failure. The specimens were found to be useful for evaluating composite frame designs.

Moas, Eduardo↗

NASA NTRS1996

Methodology for Physics and Engineering of Reliable Products

Physics of failure approaches have gained wide spread acceptance within the electronic reliability community. These methodologies involve identifying root cause failure mechanisms, developing associated models, and utilizing these models to inprove time to market, lower development and build costs and higher reliability. The methodology outlined herein sets forth a process, based on integration of both physics and engineering principles, for achieving the same goals.

failure analysis electronics reliability PACT (pre↗

NASA NTRS2002

Intralaminar and Interlaminar Progressive Failure Analysis of Composite Panels with Circular Cutouts

A progressive failure methodology is developed and demonstrated to simulate the initiation and material degradation of a laminated panel due to intralaminar and interlaminar failures. Initiation of intralaminar failure can be by a matrix-cracking mode, a fiber-matrix shear mode, and a fiber failure mode. Subsequent material degradation is modeled using damage parameters for each mode to selectively reduce lamina material properties. The interlaminar failure mechanism such as delamination is simulated by positioning interface elements between adjacent sublaminates. A nonlinear constitutive law is postulated for the interface element that accounts for a multi-axial stress criteria to detect the initiation of delamination, a mixed-mode fracture criteria for delamination progression, and a damage parameter to prevent restoration of a previous cohesive state. The methodology is validated using experimental data available in the literature on the response and failure of quasi-isotropic panels with centrally located circular cutouts loaded into the postbuckling regime. Very good agreement between the progressive failure analyses and the experimental results is achieved if the failure analyses includes the interaction of intralaminar and interlaminar failures.

Goyal, Vinay K.↗

NASA NTRS1989

Effect of a high temperature cycle on the mechanical properties of silicon carbide/titanium metal matrix composites

An investigation is conducted of the effects of the SPF/DB cycle on continuous SiC fiber-reinforced Ti-15V-3Cr-3Al-3Sn composite's matrix, fiber, and matrix-fiber interface. The fibers in question, designated SCS-6, have a carbon core and thin, carbon-rich surface. The fatigue endurance limit at 50,000 cycles for the SPF/DB specimens was 50 percent lower than for the as-fabricated material. The substantial changes in tensile strength, fatigue life, and fracture-surface appearance due to the SPF-DB cycle are explained by a difference in the failure mechanisms due to SPF/DB-induced changes in the fiber/matrix interface strength.

Naik, R. A.↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗

NASA NTRS1983

Evaluation of the emission capabilities of Spindt-type field emitting cathodes

The electron emitting capabilities of Spindt-type field emitting cathodes (FEC) are being studied at the Lewis Research Center, NASA. These cathodes, having 5000 emitting points in a 1 mm diameter, have been shown to be capable of emission current densities of 10 A/sq cm and higher. The purposes of this study are to (1) demonstrate that the cathodes can be processed and used in a tube-type configuration, (2) determine whether, at a sufficiently high current density, the cathode can operate in the space charge mode, and (3) evaluate failure mechanisms in this unique type of electron emitter. FEC's have been tested in a diode configuration, by the use of pulse techniques, up to current densities of 6 A/sq cm and anode potentials of 3000 V. Space charge effects have been observed in the range of 5 A/sq cm as an apparent linear increase of cathode current with anode voltage for a constant emitter-gate potential. Failed cathodes were studied by means of scanning electron microscopy and the major failure modes encountered are attributed to gas evolution, followed by arcing, which destroys either individual emitters or a large segment of the cathode area.

Forman, R.↗

NASA NTRS1999

Thermal-Mechanical Stability of Single Crystal Oxide Refractive Concentrators for High-Temperature Solar Thermal Propulsion

Single crystal oxides such as yttria-stabilized zirconia (Y2O3-ZrO2), yttrium aluminum garnet (Y3Al5O12, or YAG), magnesium oxide (MgO) and sapphire (Al2O3) are candidate refractive secondary concentrator materials for high temperature solar propulsion applications. However, thermo-mechanical reliability of these components in severe thermal environments during the space mission sun/shade transition is of great concern. Simulated mission tests are important for evaluating these candidate oxide materials under a variety of transient and steady-state heat flux conditions, and thus provide vital information for the component design. In this paper, a controlled heat flux thermal shock test approach is established for the single crystal oxide materials using a 3.0 kW continuous wave CO2 laser, with a wavelength 10.6 micron. Thermal fracture behavior and failure mechanisms of these oxide materials are investigated and critical temperature gradients are determined under various temperature and heating conditions. The test results show that single crystal sapphire is able to sustain the highest temperature gradient and heating-cooling rate, and thus exhibit the best thermal shock resistance, as compared to the yttria-stabilized zirconia, yttrium aluminum garnet, and magnesium oxide.

Zhu, Dongming↗

NASA NTRS1999

Thermal-Mechanical Stability of Single Crystal Oxide Refractive Concentrators for High-Temperature Solar Thermal Propulsion

Single crystal oxides such as yttria-stabilized zirconia (Y2O3-ZrO2), yttrium aluminum garnet (Y3Al5O12, or YAG), magnesium oxide (MgO) and sapphire (Al2O3) are candidate refractive secondary concentrator materials for high temperature solar propulsion applications. However, thermo-mechanical reliability of these components in severe thermal environments during the space mission sun/shade transition is of great concern. Simulated mission tests are important for evaluating these candidate oxide materials under a variety of transient and steady-state heat flux conditions, and thus provide vital information for the component design. In this paper, a controlled heat flux thermal shock test approach is established for the single crystal oxide materials using a 3.0 kW continuous wave CO2 laser, with a wavelength 10.6 micron. Thermal fracture behavior and failure mechanisms of these oxide materials are investigated and critical temperature gradients are determined under various temperature and heating conditions. The test results show that single crystal sapphire is able to sustain the highest temperature gradient and heating-cooling rate, and thus exhibit the best thermal shock resistance, as compared to the yttria-stabilized zirconia, yttrium aluminum garnet and magnesium oxide.

Zhu, Dongming↗

NASA NTRS1988

Electromigration in thin-film photovoltaic module metallization systems

Electromigration as a possible thin-film module failure mechanism was investigated using several specially made, fully aluminized thin-film photovoltaic (TF-PV) modules. The effect of electromigration, as determined experimentally by measuring increases in electrical resistance across scribe lines, can be expressed as the product of a damage function, which correlates degradation rate with operating conditions such as current density and temperature, and a susceptibility function, which is defined by module design parameters, particularly aluminum purity and the configuration of the intercell region. Experimental measurements and derived acceleration factors suggest that open-circuit failure resulting from electromigration should not be a serious problem in present state-of-the-art TF-PV modules. Nevertheless, significant intercell resistance increases can result from long-term electromigration exposure, especially in future high-efficiency modules. The problem can be alleviated, however, by appropriate metallization applications and/or proper design of the intercell region.

Wen, L.↗

NASA NTRS1991

Flow and fracture behavior of NiAl in relation to the brittle-to-ductile transition temperature

NiAl has only three independent slip systems operating at low and intermediate temperatures whereas five independent deformation mechanisms are required to satisfy the von Mises criterion for general plasticity in polycrystalline materials. Yet, it is generally recognized that polycrystalline NiAl can be deformed extensively in compression at room temperature and that limited tensile ductility can be obtained in extruded materials. In order to determine whether these results are in conflict with the von Mises criterion, tension and compression tests were conducted on powder-extruded, binary NiAl between 300 and 1300 K. The results indicate that below the brittle-to-ductile transition temperature (BDTT) the failure mechanism in NiAl involves the initiation and propagation of cracks at the grain boundaries which is consistent with the von Mises analysis. Furthermore, evaluation of the flow behavior of NiAl indicates that the transition from brittle to ductile behavior with increasing temperature coincides with the onset of recovery mechanisms such as dislocation climb. The increase in ductility above the BDTT is therefore attributed to the climb of the 001 line type dislocations which in combination with dislocation glide enable grain boundary compatibility to be maintained at the higher temperatures.

Noebe, R. D.↗