SEARCH · Search NASA

Results for “physical tests”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1989

PMR Graphite Engine Duct Development

The objective was to demonstrate the cost and weight advantages that could be obtained by utilizing the graphite/PMR15 material system to replace titanium in selected turbofan engine applications. The first component to be selected as a basis for evaluation was the outer bypass duct of the General Electric F404 engine. The operating environment of this duct was defined and then an extensive mechanical and physical property test program was conducted using material made by processing techniques which were also established by this program. Based on these properties, design concepts to fabricate a composite version of the duct were established and two complete ducts fabricated. One of these ducts was proof pressure tested and then run successfully on a factory test engine for over 1900 hours. The second duct was static tested to 210 percent design limit load without failure. An improved design was then developed which utilized integral composite end flanges. A complete duct was fabricated and successfully proof pressure tested. The net results of this effort showed that a composite version of the outer duct would be 14 percent lighter and 30 percent less expensive that the titanium duct. The other type of structure chosen for investigation was the F404 fan stator assembly, including the fan stator vanes. It was concluded that it was feasible to utilize composite materials for this type structure but that the requirements imposed by replacing an existing metal design resulted in an inefficient composite design. It was concluded that if composites were to be effectively used in this type structure, the design must be tailored for composite application from the outset.

Stotler, C. L.↗

NASA NTRS1989

VLA-Max '91 tests of high energy flare physics

The potential for the Very Large Array (VLA) contributions during the coming maximum in solar activity is illustrated by unpublished observations of solar flares on 28 May, 8 June, 24 June, and 30 September 1988. Some of this data appears in the two papers by Willson et al., referenced in this article. The VLA can be used to spatially resolve flaring active regions and their magnetic fields. These results can be compared with simultaneous x ray and gamma ray observations from space. Examples are provided in which spatially separated radio sources are resolved for the pre-burst, impulsive and decay phases of solar flares. The emergence of precursor coronal loops probably triggers the release of stored magnetic energy in adjacent coronal loops. Noise storm enhancements can originate in large-scale coronal loops on opposite sides of the visible solar disk. An interactive feedback mechanism may exist between activity in high-lying 90 cm coronal loops and lower-lying 20 cm ones.

Lang, Kenneth R.↗

NASA NTRS1989

A complete sample of double-lobed radio quasars for VLBI tests of source models - Definition and statistics

A complete, flux-density-limited sample of double-lobed radio quasars is defined, with nuclei bright enough to be mapped with the Mark III VLBI system. It is shown that the statistics of linear size, nuclear strength, and curvature are consistent with the assumption of random source orientations and simple relativistic beaming in the nuclei. However, these statistics are also consistent with the effects of interaction between the beams and the surrounding medium. The distribution of jet velocities in the nuclei, as measured with VLBI, will provide a powerful test of physical theories of extragalactic radio sources.

Hough, D. H.↗

NASA NTRS1990

Composite materials for space applications

The objectives of the program were to: generate mechanical, thermal, and physical property test data for as-fabricated advanced materials; design and fabricate an accelerated thermal cycling chamber; and determine the effect of thermal cycling on thermomechanical properties and dimensional stability of composites. In the current program, extensive mechanical and thermophysical property tests of various organic matrix, metal matrix, glass matrix, and carbon-carbon composites were conducted, and a reliable database was constructed for spacecraft material selection. Material property results for the majority of the as-fabricated composites were consistent with the predicted values, providing a measure of consolidation integrity attained during fabrication. To determine the effect of thermal cycling on mechanical properties, microcracking, and thermal expansion behavior, approximately 500 composite specimens were exposed to 10,000 cycles between -150 and +150 F. These specimens were placed in a large (18 cu ft work space) thermal cycling chamber that was specially designed and fabricated to simulate one year low earth orbital (LEO) thermal cycling in 20 days. With this rate of thermal cycling, this is the largest thermal cycling unit in the country. Material property measurements of the thermal cycled organic matrix composite laminate specimens exhibited less than 24 percent decrease in strength, whereas, the remaining materials exhibited less than 8 percent decrease in strength. The thermal expansion response of each of the thermal cycled specimens revealed significant reduction in hysteresis and residual strain, and the average CTE values were close to the predicted values.

Rawal, Suraj P.↗

NASA NTRS1991

Propulsion simulator for magnetically-suspended wind tunnel models

The objective of phase two of a current investigation sponsored by NASA Langley Research Center is to demonstrate the measurement of aerodynamic forces/moments, including the effects of exhaust gases, in magnetic suspension and balance system (MSBS) wind tunnels. Two propulsion simulator models are being developed: a small-scale and a large-scale unit, both employing compressed, liquified carbon dioxide as propellant. The small-scale unit was designed, fabricated, and statically-tested at Physical Sciences Inc. (PSI). The large-scale simulator is currently in the preliminary design stage. The small-scale simulator design/development is presented, and the data from its static firing on a thrust stand are discussed. The analysis of this data provides important information for the design of the large-scale unit. A description of the preliminary design of the device is also presented.

Joshi, Prakash B.↗

NASA NTRS1991

Effects of space environment on space-based radar phased-array antenna: Status and preliminary observations

The overall objective is to evaluate the effect of the space environment on Kapton films considered for the Grumman space based radar (SBR) phased-array antenna. The most striking result is the overall good condition of the Kapton antenna planes and Kapton tensile specimens. This is largely attributable to the orientation of the Kapton (parallel and flush on the space end) and the stability of the LDEF in orbit. Results on elongation and mechanical properties of the plain and fiberglass reinforced Kapton will be described. Stress-dependent permanent deformation and some reductions in strain to failure were observed. Physical property testing of the materials is in progress. Electronic data acquisition and memory systems appeared to operate correctly, but functional tests were not yet performed. An evaluation of the high voltage-plasma interaction data is underway. Some minor systems anomalies (e.g., fastener sheared during removal, strong odor inside electronics container) were noted. Other observations such as radiation, contamination, impacts, and orientation features of atomic oxygen erosion are reported.

Whiteside, J. B.↗

NASA NTRS1989

An evaluation of the interfacial bond properties between carbon phenolic and glass phenolic composites

The effects of moisture and surface finish on the mechanical and physical properties of the interfacial bond between the carbon/phenolic (C/P) and glass/phenolic (G/P) composite materials are presented. Four flat panel laminates were fabricated using the C/P and G/P materials. Of the four laminates, one panel was fabricated in which the C/P and G/P materials were cured simultaneously. It was identified as the cocure. The remaining laminates were processed with an initial simultaneous cure of the three C/P billets. Two surface finishes, one on each half, were applied to the top surface. Prior to the application and cure of the G/P material to the machined surface of the three C/P panels, each was subjected to the specific environmental conditioning. Types of conditioning included: (1) nominal fabrication environment, (2) a prescribed drying cycle, and (3) a total immersion in water at 160 F. Physical property tests were performed on specimens removed from the C/P materials of each laminate for determination of the specific gravity, residual volatiles and and resin content. Comparisons of results with shuttle solid rocket motor (SRM) nozzle material specifications verified that the materials used in fabricating the laminates met acceptance criteria and were representative of SRM nozzle materials. Mechanical property tests were performed at room temperature on specimens removed from the G/P, the C/P and the interface between the two materials for each laminate. The double-notched shear strength test was used to determine the ultimate interlaminar shear strength. Results indicate no appreciable difference in the C/P material of the four laminates with the exception of the cocure laminate, where 20 percent reduction in the strength was observed. The most significant effect and the ultimate strength was significantly reduced in the wet material. No appreciable variation was noted between the surface finishes in the wet laminate.

Jordan, Kelvin↗

NASA NTRS1992

Measurement of mechanical and thermophysical properties of dimensionally stable materials for space applications

Mechanical, thermal, and physical property test data was generated for as-fabricated advanced composite materials at room temperature (RT), -150 and 250 F. The results are documented of mechanical and thermophysical property tests of IM7/PEEK and discontinuous SiC/Al (particulate (p) and whisker (w) reinforced) composites which were tested at three different temperatures to determine the effect of temperature on material properties. The specific material systems tested were IM7/PEEK (0)8, (0, + or - 45, 90)s, (+ or - 30, 04)s, 25 vol. pct. (v/o) SiCp/Al, and 25 v/o SiCw/Al. RT material property results of IM7/PEEK were in good agreement with the predicted values, providing a measure of consolidation integrity attained during fabrication. Results of mechanical property tests indicated that modulus values at each test temperature were identical, whereas the strength (e.g., tensile, compressive, flexural, and shear) values were the same at -150 F, and RT, and gradually decreased as the test temperature was increased to 250 F. Similar trends in the strength values was also observed in discontinuous SiC/Al composites. These results indicate that the effect of temperature was more pronounced on the strength values than modulus values.

Rawal, Suraj P.↗

NASA NTRS1992

Effects of the space environment on space-based radar phased-array antenna; status and preliminary observations (LDEF Experiment A0133)

The overall objective of the experiment was to evaluate the effect of the space environment on components considered for a Space-Based Radar (SBR) Phased-Array Antenna. Of primary interest was a study of the degradation of the polyimide film Kapton (DuPont trademark), the material considered for use in the antenna plane. The most striking result of the experiment was the overall good condition of the Kapton antenna planes and Kapton tensile specimens, despite nearly six years of exposure to the space environment. This was largely attributable to the orientation of the Kapton (parallel and flush on the space end) and the stability of the Long Duration Exposure Facility (LDEF) in orbit. However, weathering of exposed Kapton surfaces was not insignificant. Results on elongation and mechanical properties of the plain and the fiberglass-reinforced Kapton are presented. Reduction in strain to failure of flight-exposed Kapton is attributed to surface defects of these specimens. Physical property testing of the materials to date reveals no significant difference between flight-exposed and control material. The second objective was to investigate the interaction between high-voltage electrodes and typical spacecraft contaminants in simulation of discharge triggering across differentially charged dielectric surfaces (spacecraft charging conditions). Electronic data acquisition and memory systems appeared to operate correctly, but very few discharges were recorded. Induced radioactivity, contamination, impacts, and orientation features of atomic oxygen erosion were observed.

J B Whiteside↗

NASA NTRS1920

Glues Used in Airplane Parts

This report was prepared for the National Advisory Committee for Aeronautics and presents the results of investigations conducted by the Forest Products Laboratory of the United States Forest Service on the manufacture, preparation, application, testing and physical properties of the different types of glues used in wood airplane parts.

Allen, S W↗

NASA NTRS1993

The ACTS propagation terminal delivery and support

Viewgraphs on the Advanced Communications Technology Satellite (ACTS) propagation terminal delivery and support are included. Topics covered include: the ACTS propagation terminal (APT) development program; terminal overview; physical units; test results; status of terminals and schedule; shipping cartons; and site support.

Stutzman, Warren L.↗

NASA NTRS1995

Weightless Environment Training Facility (WETF) Materials Coating Evaluation, Volume 1

The Weightless Environment Training Facility Material Coating Evaluation project has included preparing, coating, testing, and evaluating 800 test panels of three differing substrates. Ten selected coating systems were evaluated in six separate exposure environments and subject to three tests for physical properties. Substrate materials were identified, the manner of surface preparation described, and exposure environments defined. Exposure environments included immersion exposure, cyclic exposure, and field exposure. Cyclic exposures, specifically QUV-Weatherometer and the KTA Envirotest were found to be the most agressive of the environments included in the study when all three evaluation criteria are considered. This was found to result primarily from chalking of the coatings under ultraviolet (UV) light exposure. Volumes 2 and 3 hold the 5 appendices to this report.

Source record↗

NASA NTRS1995

Weightless Environment Training Facility (WETF) materials coating evaluation, volume 2

This volume consists of Appendices A and B to the report on the Weightless Environment Training Facility Materials Coating Evaluation project. The project selected 10 coating systems to be evaluated in six separate exposure environments, and subject to three tests for physical properties. Appendix A holds the coating system, surface preparation, and application data. Appendix B holds the coating material infrared spectra.

Source record↗

NASA NTRS1997

Development of Processing Techniques for Advanced Thermal Protection Materials

During the period June 1, 1996 through May 31, 1997, the main effort has been in the development of materials for high temperature applications. Thermal Protection Systems (TPS) are constantly being tested and evaluated for thermal shock resistance, high temperature dimensional stability, and tolerance to environmental effects. Materials development was carried out by using many different instruments and methods, ranging from intensive elemental analysis to testing the physical attributes of a material. The material development concentrated on two key areas: (1) development of coatings for carbon/carbon composites, and (2) development of ultra-high temperature ceramics (UHTC). This report describes the progress made in these two areas of research during this contract period.

Selvaduray, Guna↗

NASA NTRS1997

The Superconducting Cavity Stabilized Oscillator

Superconducting Cavity Stabilized Oscillators (SCSOs) have produced the most stable clocks to date for integration times between 10(exp 2) and 10(exp 3) seconds, achieving a fractional frequency stability of 2 x 10(exp -16) for a sampling time of 100 s. The principal contributors to cavity frequency variations are: (1) acceleration effects due to gravity and vibrations; (2) temperature variations; (3) variations in the energy stored in the cavity; and (4) noise introduced by the frequency stabilization circuit. We discuss the prospects for improvements in all these areas for both ground-based and space-based SCSOs, which may lead to SCSOs with fractional frequency stabilities below 10(exp -17). SCSOs of this frequency stability will be useful for testing fundamental physical principles.

Turneaure, J. P.↗

NASA NTRS1999

Nickel-Hydrogen Cell Testing Experience, NASA/Goddard Space Flight Center

The objectives of the project were to test the Nickel-Hydrogen Cell to: (1) verify the Aerospace Cell Flight Worthiness, (2) Elucidate the Aerospace Cell Thermal Behavior, (3) Develop the Aerospace Battery Assembly Design(s) and In-orbit Battery Management plan(s) and (4) Understand the Aerospace Cell Failure Mechanism. The tests included the LEO and GEO Life cycle tests, Calorimetric Analysis, Destructive Physical analysis, and special tests. Charts show the Mission Profile Cycling Data, Stress Cycling Data. The test data complies with the mission requirements, validating the flight worthiness of batteries. The nominal stress and mission profile cycling performance test shows the charge voltage as high as 1.60V and recharge ratio greater than 1.05. It is apparent that the electrochemical signatures alone do not provide conclusive proof for Nickel precharge. The researchers recommend a gas and positive plate analyses for further confirmation.

Rao, Gopalakrishna M.↗

NASA NTRS2005

Regression Analysis of Long-term Profile Ozone Data Set from BUV Instruments

Frith, Stacey↗

NASA NTRS2005

Regression Analysis of Long-Term Profile Ozone Data Set from BUV Instruments

We have produced a profile merged ozone data set (MOD) based on the SBUV/SBUV2 series of nadir-viewing satellite backscatter instruments, covering the period from November 1978 - December 2003. In 2004, data from the Nimbus 7 SBUV and NOAA 9, ll, and 16 SBUV/2 instruments were reprocessed using the Version 8 (V8) algorithm and most recent calibrations. More recently, data from the Nimbus 4 BUT instrument, which was operational from 1970 - 1977, were also reprocessed using the V8 algorithm. As part of the V8 profile calibration, the Nimbus 7 and NOAA 9 (1993-1997 only) instrument calibrations have been adjusted to match the NOAA 11 calibration, which was established based on comparisons with SSBUV shuttle flight data. Differences between NOAA 11, Nimbus 7 and NOAA 9 profile zonal means are within plus or minus 5% at all levels when averaged over the respective periods of data overlap. NOAA 16 SBUV/2 data have insufficient overlap with NOAA 11, so its calibration is based on pre-flight information. Mean differences over 4 months of overlap are within plus or minus 7%. Given the level of agreement between the data sets, we simply average the ozone values during periods of instrument overlap to produce the MOD profile data set. Initial comparisons of coincident matches of N4 BUV and Arosa Umkehr data show mean differences of 0.5 (0.5)% at 30km; 7.5 (0.5)% at 35 km; and 11 (0.7)% at 40 km, where the number in parentheses is the standard error of the mean. In this study, we use the MOD profile data set (1978-2003) to estimate the change in profile ozone due to changing stratospheric chlorine levels. We use a standard linear regression model with proxies for the seasonal cycle, solar cycle, QBO, and ozone trend. To account for the non-linearity of stratospheric chlorine levels since the late 1990s, we use a time series of Effective Chlorine, defined as the global average of Chlorine + 50 * Bromine at 1 hPa, as the trend proxy. The Effective Chlorine data are taken from the 3-D Goddard CTM. We will show the latest trend results using this statistical model. In addition, the Nimbus 4 BUV data offer an opportunity to test the physical properties of our statistical model. From ground-based comparisons we will establish an uncertainty range for the Nimbus 4 data. We then extrapolate our statistical model fit backwards in time and compare to the Nimbus 4 data. We compare the characteristics of the residual, defined as the difference between the data and statistical regression fit, during the Nimbus 4 time period and the 1978-2003 period over which the statistical model coefficients were estimated, and present these results.

Stolarski, Richard S.↗