Search NASA⌕ Search

SEARCH · Search NASA

Results for “rectifiers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

ZnO homojunction photodiodes based on Sb-doped p-type nanowire array and n-type film for ultraviolet detection

ZnO p-n homojunctions based on Sb-doped p-type nanowire array and n-type film were grown by combining chemical vapor deposition (for nanowires) with molecular-beam epitaxy (for film). Indium tin oxide and Ti/Au were used as contacts to the ZnO nanowires and film, respectively. Characteristics of field-effect transistors using ZnO nanowires as channels indicate p-type conductivity of the nanowires. Electron beam induced current profiling confirmed the existence of ZnO p-n homojunction. Rectifying I-V characteristic showed a turn-on voltage of around 3 V. Very good response to ultraviolet light illumination was observed from photocurrent measurements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Energetic deposition of carbon in a cathodic vacuum arc with a biased mesh

Carbon films were deposited in a filtered cathodic vacuum arc with a bias potential applied to a conducting mesh mounted in the plasma stream between the source and the substrate. We determined the stress and microstructural properties of the resulting carbon films and compared the results with those obtained using direct substrate bias with no mesh. Since the relationship between deposition energy and the stress, sp{sup 2} fraction and density of carbon are well known, measuring these film properties enabled us to investigate the effect of the mesh on the energy and composition of the depositing flux. When a mesh was used, the film stress showed a monotonic decrease for negative mesh bias voltages greater than 400V, even though the floating potential of the substrate did not vary. We explain this result by the neutralization of some ions when they are near to or passing through the negatively biased mesh. The microstructure of the films showed a change from amorphous to glassy carbonlike with increasing bias. Potential applications for this method include the deposition of carbon films with controlled stress on low conductivity substrates to form rectifying or ohmic contacts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quasilinear theory and simulation of Buneman instability

In a recently developed nonlinear theory of Buneman instability, a simplifying assumption of self-similarity was imposed for the electron distribution function, based upon which, a set of moment kinetic equations was derived and solved together with nonlinear wave kinetic equation [P. H. Yoon and T. Umeda, Phys. Plasmas 17, 112317 (2010)]. It was found that the theoretical result compared reasonably against one-dimensional electrostatic Vlasov simulation. In spite of this success, however, the simulated distribution deviated appreciably from the assumed self-similar form during the late stages of nonlinear evolution. In order to rectify this shortcoming, in this paper, the distribution function is computed on the basis of rigorous velocity space diffusion equation. A novel theoretical scheme is developed so that both the quasilinear particle diffusion equation and the adiabatic dispersion relation can be solved for an arbitrary particle distribution function. Comparison with Vlasov simulation over relatively early quasilinear phase of the instability shows a reasonable agreement, despite the fact that quasilinear theory lacks coherent nonlinear effects as well as mode-mode coupling effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Power Conversion Efficiency of AlGaAs/GaAs Schottky Diode for Low-Power On-Chip Rectenna Device Application

A Schottky diode has been designed and fabricated on n-AlGaAs/GaAs high-electron-mobility-transistor (HEMT) structure. Current-voltage (I-V) measurements show good device rectification with a Schottky barrier height of 0.4349 eV for Ni/Au metallization. The differences of Schottky barrier height from theoretical value are due to the fabrication process and smaller contact area. The RF signals up to 1 GHz are well rectified by the fabricated Schottky diodes and stable DC output voltage is obtained. Power conversion efficiency up to 50% is obtained at 1 GHz with series connection between diode and load. The fabricated the n-AlGaAs/GaAs Schottky diode provide conduit for breakthrough designs for ultra-low power on-chip rectenna device technology to be integrated in nanosystems.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Hot electron transmission in metals using epitaxial NiSi{sub 2}/n-Si(111) interfaces

We have investigated hot electron transmission across epitaxial metal-disilicide/n-Si(111) interfaces using ballistic electron emission microscopy (BEEM). Different crystal orientations of epitaxial NiSi{sub 2} were grown on a Si(111) substrate using molecular beam epitaxy. The presence of different interfaces of NiSi{sub 2} on Si(111) were confirmed by high resolution transmission electron microscopy. Electrical transport measurements reveal a clear rectifying Schottky interface with a barrier height of 0.69 eV. However, using BEEM, three different regions with different transmissions and Schottky barrier heights of 0.65 eV, 0.78 eV, and 0.71 eV are found. The addition of a thin Ni film on the NiSi{sub 2} layer strongly reduces the transmission in all the three regions and interestingly, almost equalizes the transmission across them.

36 MATERIALS SCIENCE↗

Optimization on photoelectric detection based on stacked La{sub 0.9}Sr{sub 0.1}MnO{sub 3-{delta}}/LaAlO{sub 3-{delta}} multijunctions

Three multijunctions consisting of La{sub 0.9}Sr{sub 0.1}MnO{sub 3-{delta}} and LaAlO{sub 3-{delta}} on Si substrate have been fabricated under different oxygen pressures by laser molecular beam epitaxy. They exhibit nonlinear and rectifying current-voltage characteristics and evident photocurrent response to He-Ne laser illumination. Experimental results indicate that the periodically stacked multijunction grown under lower oxygen pressure shows a better rectification behavior and a higher photocurrent. The photovoltaic responsivities of the multijunctions are enhanced greatly at reverse bias and are much higher than that of a similarly grown single p-n junction. Based on the band structure of the multilayers, a possible mechanism of the photovoltaic process was proposed. A high photovoltage responsivity of 168.6 mV/mW has been achieved at - 6 V bias; this demonstrates the potential of the present multijunction configuration for photodetectors operating at room temperature.

36 MATERIALS SCIENCE↗

Electronic states at the interface between indium tin oxide and silicon

Electronic properties and thermal stability of interfacial states between indium tin oxide (ITO) and monocrystalline silicon (Si) have been investigated. ITO films with thicknesses of about 300 nm were deposited by dc magnetron sputtering on n- and p-type (100) Si at room temperature. The samples were then annealed for 30 min at different temperatures in the range 100-600 deg. C, and the ITO-Si junction was found to exhibit rectifying behavior. Current-voltage (IV), capacitance-voltage (CV), and deep-level transient spectroscopy (DLTS) measurements have been used to electrically characterize the ITO-Si interface. DLTS measurements on p-type Si samples reveal a dominant hole trap at around 0.37 eV above the valence band edge. In the n-type samples, a broad band of electron traps occur in the range 0.1-0.2 eV below the conduction band edge. These electron traps display wide DLTS peaks, indicating a band of electronic energy levels rather than well-defined states originating from isolated point defects. All the traps in both the p- and n-type samples are found to be located near the ITO-Si interface. Investigations of the thermal stability of the observed electronic states show that the dominant hole trap anneal out after 30 min at 250 deg. C, while the dominant electron traps can be stable up to 500 deg. C. IV and DLTS measurements demonstrate a clear correlation between the annealing of the dominant electronic states and increase in the junction rectification.

36 MATERIALS SCIENCE↗

Growth of GaN on Si(111): Surfaces and crystallinity of the epifilms and the transport behavior of GaN/Si heterojunctions

Growths of GaN on Si(111) - (7 x 7) substrates by plasma-assisted molecular-beam epitaxy (PA-MBE) have been studied. Optimal conditions of MBE and the effect of a low-temperature (LT) buffer are followed. It is found that irrespective of the growth conditions and the growth strategies (direct versus two-step growth), a thin amorphous-like interface layer always forms. For smooth surfaces and better crystallinity of the epifilms, a LT-buffer preceding the high-temperature deposition is helpful, and the grown GaN films are of nitrogen-polar. Transport measurements of the heterojunctions of GaN on heavily p- and n-doped Si reveal ohmic behavior, whereas that of n-GaN on lightly doped n{sup -}-Si substrate shows rectifying characteristics.

36 MATERIALS SCIENCE↗

Substrate nitridation induced modulations in transport properties of wurtzite GaN/p-Si (100) heterojunctions grown by molecular beam epitaxy

Phase pure wurtzite GaN films were grown on Si (100) substrates by introducing a silicon nitride layer followed by low temperature GaN growth as buffer layers. GaN films grown directly on Si (100) were found to be phase mixtured, containing both cubic ({beta}) and hexagonal ({alpha}) modifications. The x-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy studies reveal that the significant enhancement in the structural as well as in the optical properties of GaN films grown with silicon nitride buffer layer grown at 800 deg. C when compared to the samples grown in the absence of silicon nitride buffer layer and with silicon nitride buffer layer grown at 600 deg. C. Core-level photoelectron spectroscopy of Si{sub x}N{sub y} layers reveals the sources for superior qualities of GaN epilayers grown with the high temperature substrate nitridation process. The discussion has been carried out on the typical inverted rectification behavior exhibited by n-GaN/p-Si heterojunctions. Considerable modulation in the transport mechanism was observed with the nitridation conditions. The heterojunction fabricated with the sample of substrate nitridation at high temperature exhibited superior rectifying nature with reduced trap concentrations. Lowest ideality factors ({approx}1.5) were observed in the heterojunctions grown with high temperature substrate nitridation which is attributed to the recombination tunneling at the space charge region transport mechanism at lower voltages and at higher voltages space charge limited current conduction is the dominating transport mechanism. Whereas, thermally generated carrier tunneling and recombination tunneling are the dominating transport mechanisms in the heterojunctions grown without substrate nitridation and low temperature substrate nitridation, respectively.

36 MATERIALS SCIENCE↗

Repelling Point Bosons

There is a body of conventional wisdom that holds that a solvable quantum problem, by virtue of its solvability, is pathological and thus irrelevant. It has been difficult to refute this view owing to the paucity of theoretical constructs and experimental results. Recent experiments involving equivalent ions trapped in a spatial conformation of extreme anisotropic confinement (longitudinal extension tens, hundreds or even thousands of times transverse extension) have modified the view of relevancy, and it is now possible to consider systems previously thought pathological, in particular point Bosons that repel in one dimension. It has been difficult for the experimentalists to utilize existing theory, mainly due to long-standing theoretical misunderstanding of the relevance of the permutation group, in particular the non-commutativity of translations (periodicity) and transpositions (permutation). This misunderstanding is most easily rectified in the case of repelling Bosons.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Studies of pure and nitrogen-incorporated hydrogenated amorphous carbon thin films and their possible application for amorphous silicon solar cells

Hydrogenated amorphous carbon (a-C:H) and nitrogen-incorporated a-C:H (a-C:N:H) thin films were deposited using radio frequency-plasma-enhanced chemical vapor deposition technique and studied for their electrical, optical, and nano-mechanical properties. Introduction of nitrogen and increase of self bias enhanced the conductivity of a-C:H and a-C:N:H films, whereas current-voltage measurement reveals heterojunction formation due to their rectifying behavior. The bandgap of these films was changed over wide range from 1.9 eV to 3.45 eV by varying self bias and the nitrogen incorporation. Further, activation energy was correlated with the electronic structure of a-C:H and a-C:N:H films, and conductivity was discussed as a function of bandgap. Moreover, a-C:N:H films exhibited high hardness and elastic modulus, with maximum values as 42 GPa and 430 GPa, respectively, at -100 V. Observed fascinating electrical, optical, and nano-mechanical properties made it a material of great utility in the development of optoelectronic devices, such as solar cells. In addition, we also performed simulation study for an a-Si:H solar cell, considering a-C:H and C:N:H as window layers, and compared their performance with the a-Si:H solar cell having a-SiC:H as window layer. We also proposed several structures for the development of a near full-spectrum solar cell. Moreover, due to high hardness, a-C:N:H films can be used as a protective and encapsulate layer on solar cells, especially in n-i-p configuration on metal substrate. Nevertheless, a-C:H and a-C:N:H as a window layer can avoid the use of additional hard and protective coating and, hence, minimize the cost of the product.

36 MATERIALS SCIENCE↗

Detection of nanosecond-scale, high power THz pulses with a field effect transistor

We demonstrate detection and resolution of high power, 34 ns free electron laser pulses using a rectifying field effect transistor. The detector remains linear up to an input power of 11 {+-} 0.5 W at a pulse energy of 20 {+-} 1 {mu}J at 240 GHz. We compare its performance to a protected Schottky diode, finding a shorter intrinsic time constant. The damage threshold is estimated to be a few 100 W. The detector is, therefore, well-suited for characterizing high power THz pulses. We further demonstrate that the same detector can be used to detect low power continuous-wave THz signals with a post detection limited noise floor of 3.1 {mu}W/{radical}(Hz). Such ultrafast, high power detectors are important tools for high power and high energy THz facilities such as free electron lasers.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electron kappa distribution and steady-state Langmuir turbulence

In a recent pair of papers, the present author discussed a self-consistent theory of asymptotically steady-state electron distribution function and Langmuir turbulence intensity in one [P. H. Yoon, Phys. Plasmas 18, 122303 (2011)] and three [P. H. Yoon, Phys. Plasmas 19, 012304 (2012)] dimensions. The resulting electron distribution function is a type of kappa distribution that features a non-Maxwellian energetic tail component. However, while the one-dimensional solution is rigorously correct, the three-dimensional solution, which was obtained using the cylindrical coordinate representation, contains two features that may be inconsistent for field-free plasmas. One is the assumption that the resonance condition can be approximated by {omega}-k{center_dot}v Almost-Equal-To {omega}-k{sub Parallel-To }v{sub Parallel-To }. Needless to say, this is not the most general condition. The second inconsistency is that while the electron distribution is isotropic in velocity, the Langmuir turbulence intensity depends on the wave propagation direction. While these features may not be too unrealistic in the presence of an implicit ambient magnetic field, they certainly cannot be correct if the plasma is genuinely unmagnetized. In the present paper, we rectify such shortcomings by properly reformulating the problem using a spherical coordinate system in a truly free-field plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Determination and correction of distortions and systematic errors in low-energy electron diffraction

We developed and implemented an algorithm to determine and correct systematic distortions in low-energy electron diffraction (LEED) images. The procedure is in principle independent of the design of the apparatus (spherical or planar phosphorescent screen vs. channeltron detector) and is therefore applicable to all device variants, known as conventional LEED, micro-channel plate LEED, and spot profile analysis LEED. The essential prerequisite is a calibration image of a sample with a well-known structure and a suitably high number of diffraction spots, e.g., a Si(111)-7×7 reconstructed surface. The algorithm provides a formalism which can be used to rectify all further measurements generated with the same device. In detail, one needs to distinguish between radial and asymmetric distortion. Additionally, it is necessary to know the primary energy of the electrons precisely to derive accurate lattice constants. Often, there will be a deviation between the true kinetic energy and the value set in the LEED control. Here, we introduce a method to determine this energy error more accurately than in previous studies. Following the correction of the systematic errors, a relative accuracy of better than 1% can be achieved for the determination of the lattice parameters of unknown samples.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electrical and chemical characteristics of probe-induced two-dimensional SiO{sub x} protrusion layers

Three two-dimensional SiO{sub x} (x {identical_to} O/Si content ratio and x > 2) protrusion layers of {approx}0.5, {approx}4, and {approx}6 nm high were induced on a native SiO{sub 2} layer by atomic force microscopy (AFM) probes. X-ray photoemission spectroscopy (XPS) was used to reveal the elemental quantity of the photoelectrons, Si 2p core-levels, and Si oxidation states in the three SiO{sub x} protrusion layers and native SiO{sub 2} layer. Pt-coated conductive AFM probes were also exploited to acquire the rectifying current-voltage (IV) characteristics of the three SiO{sub x} protrusion layers and the native SiO{sub 2} layer, indicating all the three SiO{sub x} protrusion layers to be good Schottky diodes.

36 MATERIALS SCIENCE↗

Core-ion temperature measurement of the ADITYA tokamak using passive charge exchange neutral particle energy analyzer

Core-ion temperature measurements have been carried out by the energy analysis of passive charge exchange (CX) neutrals escaping out of the ADITYA tokamak plasma (minor radius, a= 25 cm and major radius, R= 75 cm) using a 45 Degree-Sign parallel plate electrostatic energy analyzer. The neutral particle analyzer (NPA) uses a gas cell configuration for re-ionizing the CX-neutrals and channel electron multipliers (CEMs) as detectors. Energy calibration of the NPA has been carried out using ion-source and {Delta}E/E of high-energy channel has been found to be {approx}10%. Low signal to noise ratio (SNR) due to VUV reflections on the CEMs was identified during the operation of the NPA with ADITYA plasma discharges. This problem was rectified by upgrading the system by incorporating the additional components and arrangements to suppress VUV radiations and improve its VUV rejection capabilities. The noise rejection capability of the NPA was experimentally confirmed using a standard UV-source and also during the plasma discharges to get an adequate SNR (>30) at the energy channels. Core-ion temperature T{sub i}(0) during flattop of the plasma current has been measured to be up to 150 eV during ohmically heated plasma discharges which is nearly 40% of the average core-electron temperature (typically T{sub e}(0) {approx} 400 eV). The present paper describes the principle of tokamak ion temperature measurement, NPA's design, development, and calibration along with the modifications carried out for minimizing the interference of plasma radiations in the CX-spectrum. Performance of the NPA during plasma discharges and experimental results on the measurement of ion-temperature have also been reported here.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Heteroepitaxial growth of GaN/Si (111) junctions in ammonia-free atmosphere: Charge transport, optoelectronic, and photovoltaic properties

We report the catalyst-free growth of gallium nitride (GaN) nanostructures on n-Si (111) substrates using physical vapor deposition via thermal evaporation of GaN powder at 1150 Degree-Sign C in the absence of NH{sub 3} gas. Scanning electron microscopy and energy dispersive x-ray analysis indicate that the growth rate of GaN nanostructures varies with deposition time. Photoluminescence spectra showed the suppression of the UV emission and the enhancement of the visible band emission with increasing the deposition time. The fabricated GaN nanostructures exhibited p-type behavior at the GaN/Si interface, which can be related to the diffusion of Ga into the Si substrate. The obtained lowest reflection and highest transmittance over a wide wavelength range (450-750 nm) indicate the high quality of the fabricated GaN films. Hall-effect measurements showed that all fabricated films have p-type behavior with decreasing electron concentration from 10{sup 21} to 10{sup 12} cm{sup -3} and increasing the electron mobility from 50 to 225 cm{sup 2}/V s with increasing the growth time. The fabricated solar cell based on the 1 h-deposited GaN nanostructures on n-Si (111) substrate showed a well-defined rectifying behavior with a rectification ratio larger than 8.32 Multiplication-Sign 10{sup 3} in dark. Upon illumination (30 mW/cm{sup 2}), the 1 h-deposited heterojunction solar cell device showed a conversion efficiency of 5.78%. The growth of GaN in the absence of NH{sub 3} gas has strong effect on the morphological, optical, and electrical properties and consequently on the efficiency of the solar cell devices made of such layers.

36 MATERIALS SCIENCE↗

Fluid modeling of radio frequency and direct currents in a biased magnetized plasma

This model aims at simulating a magnetized plasma column connected on one side to a probe and on the other side to an ICRH (Ion Cyclotron Resonant Heating) antenna. This is a double probe modeling of a plasma flux tube exchanging perpendicular currents: rf polarization current and dc currents (inertia, viscous, and friction) perpendicular to the magnetic field. A self consistent solution for the rectified potential and the density is obtained under the assumptions of flute hypothesis, inertialess electrons, and no collision in parallel direction. The main effect of rf biasing on the antenna side is to shift the IV characteristic so that the floating potential can be increased up to ln(I{sub 0}(eV{sub rf}/(k{sub B}T{sub e}))), with I{sub 0} the modified Bessel function of the first kind. On the contrary, the effect of dc currents is to decrease the plasma potential and the sheath potential which can be lower than 3k{sub B}T{sub e}/e or even be negative. Experimental characteristics are well matched by the 1D fluid code and exhibit very high negative currents (more than 30 j{sub i} the ion saturation current) for high positive biasing of the probe and for long flux tube (10 m). The non-saturation of the electron current is here due to high transverse transport enhanced by convective fluxes and dc currents able to bring an amount of density around the biased flux tube. During comparisons with experiments, the floating potential measured by a reciprocating probe is recovered by the code revealing that for a 120 V measured peak potential on the probe, the rf potential on the ICRH antenna is twice this value. Finally, the density profile can be flattened or steepened as a function of the transverse dc current direction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗