SEARCH · Search NASA

Results for “representativeness analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Investigation of the sensitivity of ionization-type vacuum gauges

A quantitative analysis of a large and representative sample of available data has been made to determine the best criteria for predicting the relative sensitivities of ionization-type vacuum gauges to different gases. The molecular property of the gas that correlates best with relative sensitivity is the ionization cross section (eV). For high-pressure ionization gauges, a cross section evaluated at 2/3 of the accelerating potential of the gauge is the best choice. For Bayard-Alpert and triode gauges, any of three choices are of approximately equal value. These are 100 eV cross section values, maximum cross section value for each gas, and a cross section evaluated at 2/3 of the accelerating potential for each gauge. For the Alphatron gauge, cross section values in the range 5000-10,000 eV provide the best correlation.

Holanda, R.↗

NASA NTRS1973

An experimental study of the motorcycle roll stabilization task

The work of Sharp represents the most complete theoretical analysis of the uncontrolled motorcycle presently available, and serves as a theoretical basis for the study described. Sharp's analysis included roll, yaw, lateral translation, and steering degrees of freedom, and the resulting equations are linear with constant coefficients. Tire aligning moments due to tire sideslip were added to Sharp's equations. Experimental results are presented, and related to the theoretical studies of Sharp and Weir.

Eaton, D. J.↗

NASA NTRS1977

Comparison of finite source and plane wave scattering from corrugated surfaces

The choice of a plane wave to represent incident radiation in the analysis of scatter from corrugated surfaces was examined. The physical optics solution obtained for the scattered fields due to an incident plane wave was compared with the solution obtained when the incident radiation is produced by a source of finite size and finite distance from the surface. The two solutions are equivalent if the observer is in the far field of the scatterer and the distance from observer to scatterer is large compared to the radius of curvature at the scatter points, condition not easily satisfied with extended scatterers such as rough surfaces. In general, the two solutions have essential differences such as in the location of the scatter points and the dependence of the scattered fields on the surface properties. The implication of these differences to the definition of a meaningful radar cross section was examined.

Levine, D. M.↗

NASA NTRS1980

Acoustoelasticity - Review and extension

Research on the interaction between the sound pressure field and the flexible wall of an enclosure is reviewed. The topics discussed include: a mathematical model, simplified solutions for sinusoidal excitation, damping, random excitation, numerical results, including comparisons with representative experimental data, and design analysis methodology. Results of various authors using finite element techniques and modal analysis suggest that effective analytical models are available.

Dowell, E. H.↗

NASA NTRS1982

Use of the thin sheath approximation for obtaining ion temperatures from the ISEE 1 limited aperture RPA

A procedure for analyzing low-energy (less than approximately 100 eV) ion data from the plasma composition experiment on ISEE 1 is set forth. The method is based on a derived analytic expression for particle flux to a limited aperture retarding potential analyzer (RPA) in the thin sheath approximation, which makes allowance for some effects of a charged spacecraft on plasma particle trajectories. Calculations using simulated data are employed in testing the efficacy and accuracy of the technique. On the basis of an analysis of these calculation results and the mathematical model, the method is seen as being able to provide accurate ion temperatures from all good plasmaspheric RPA data. It is noted that corresponding densities and spacecraft potentials should be accurate when spacecraft potentials are negative but that they are subject to error for positive spacecraft potentials, particularly when ion Mach numbers are much less than 1. An analysis of data from a representative ISEE 1 pass produces a plasmasphere temperature profile that is consistent in overall structure with previous observations.

Comfort, R. H.↗

NASA NTRS1983

The properties of coronal voids

Skylab coronagraph observations of the outer solar corona have revealed dark, ray-like structures whose identification as a true coronal phenomenon rather than a subtle photographic effect is presently undertaken. Photometric analysis indicates that these features represent a reduction of 5% in coronal radiance, and the use of a previously developed model of the coronal electron component allows the specification of void electron densities over a 2.5-4.5 solar radius range. Projection of the phenomena onto synoptic surface maps indicates a close relationship with filaments and neutral lines, and a potentially significant temporal correlation between void formation and the formation of the underlying prominence is noted.

Macqueen, R. M.↗

NASA NTRS1985

A software technology evaluation program

A set of quantitative approaches is presented for evaluating software development methods and tools. The basic idea is to generate a set of goals which are refined into quantifiable questions which specify metrics to be collected on the software development and maintenance process and product. These metrics can be used to characterize, evaluate, predict, and motivate. They can be used in an active as well as passive way by learning form analyzing the data and improving the methods and tools based upon what is learned from that analysis. Several examples were given representing each of the different approaches to evaluation. The cost of the approaches varied inversely with the level of confidence in the interpretation of the results.

Novaes-Card, David N.↗

NASA NTRS1989

Shear buckling of specially orthotropic plates with centrally located cutouts

The shear loading of a composite rectangular plate with a centrally located circular cutout was analyzed in order to predict the buckling load of the plate. The first step in this analysis is to calculare the in-plane stress distribution of the plate prior to buckling. This problem can be solved using finite element methods, but a quicker and more cost efficient method is desired. The method chosen to determine the pre-buckling stresses is that of boundary collocation using complex variables. The real valued force functions are written in terms of two complex valued functions, each of which is a function of a different complex variable. The solution of the generalized biharmonic function is a superposition of functions of these two complex variables. For this analysis, the force functions are represented with a Laurent series. The constants in these series are found using boundary collocation. Two force equations for complex variables are satisfied over the plate boundaries to obtain these constants. The stresses in the plate are then known for any particular locations on the plate given the applied shear on the edges of the plate.

Klang, Eric C.↗

NASA NTRS1990

Evaluation of thermal loading on a methane injector at high pressure and temperature

Experimental and numerical analyses are conducted to determine the surface temperature on a methane fuel injector used to produce a high enthalpy test stream for a combustion-fed subscale wind tunnel facility. It was found that the ratio of the methane fuel injection velocity to the air stream velocity is a significant factor in the production of high injector surface temperatures which lead to rapid deterioration of the fuel injector structure. The numerical code utilized for the computational analysis was found to be representative of the experimentally measured data since the experimental trends were reproduced by the numerical simulation. The quantitative accuracy of the numerical predictions could not be assessed from the data gathered because of the difficulty of making a noninterfering injector surface temperature measurement. The numerical code can be used for parametric evaluation of combustor parameters and thus will serve as an important tool in the design of such fuel injector systems.

Harvin, Stephen F.↗

NASA NTRS1991

Calculating Flow Through A Helicopter Rotor

New method for calculating flow of air through and around helicopter rotor incorporated into General Rotorcraft Aeromechanical Stability Program (GRASP) (computer program for aeroelastic analysis). Flow about helicopter rotor represented by axisymmetric flow field in cylindrical region with actuator disk as source of flow.

Kunz, Donald L.↗

NASA NTRS1992

Computational aspects of helicopter trim analysis and damping levels from Floquet theory

Helicopter trim settings of periodic initial state and control inputs are investigated for convergence of Newton iteration in computing the settings sequentially and in parallel. The trim analysis uses a shooting method and a weak version of two temporal finite element methods with displacement formulation and with mixed formulation of displacements and momenta. These three methods broadly represent two main approaches of trim analysis: adaptation of initial-value and finite element boundary-value codes to periodic boundary conditions, particularly for unstable and marginally stable systems. In each method, both the sequential and in-parallel schemes are used and the resulting nonlinear algebraic equations are solved by damped Newton iteration with an optimally selected damping parameter. The impact of damped Newton iteration, including earlier-observed divergence problems in trim analysis, is demonstrated by the maximum condition number of the Jacobian matrices of the iterative scheme and by virtual elimination of divergence. The advantages of the in-parallel scheme over the conventional sequential scheme are also demonstrated.

Gaonkar, Gopal H.↗

NASA NTRS1992

Origins for the near-earth asteroids

Because of their short dynamical lifetimes, the population of near-earth asteroids (NEAs) must be resupplied. Two sources have been hypothesized: main-belt asteroids and extinct comet nuclei. A new survey of physical properties for less than 5 kilometers diameter main-belt asteroids reveals that their spin rate and shape distributions are similar to those of NEAs, as is fully consistent with a main-belt origin for most NEAs. Physical data on comet nuclei are limited. If the existing sample is representative of the comet population, analysis of the asteroid and comet samples constrains the fraction of comet nuclei to between 0 and 40 percent of the total NEA population.

Binzel, Richard P.↗

NASA NTRS1993

Helicopter trim analysis by shooting and finite element methods with optimally damped Newton iterations

Helicopter trim settings of periodic initial state and control inputs are investigated for convergence of Newton iteration in computing the settings sequentially and in parallel. The trim analysis uses a shooting method and a weak version of two temporal finite element methods with displacement formulation and with mixed formulation of displacements and momenta. These three methods broadly represent two main approaches of trim analysis: adaptation of initial-value and finite element boundary-value codes to periodic boundary conditions, particularly for unstable and marginally stable systems. In each method, both the sequential and in-parallel schemes are used, and the resulting nonlinear algebraic equations are solved by damped Newton iteration with an optimally selected damping parameter. The impact of damped Newton iteration, including earlier-observed divergence problems in trim analysis, is demonstrated by the maximum condition number of the Jacobian matrices of the iterative scheme and by virtual elimination of divergence. The advantages of the in-parallel scheme over the conventional sequential scheme are also demonstrated.

Achar, N. S.↗

NASA NTRS1995

Prediction of Wind Tunnel Effects on the Installed F/A-18A Inlet Flow Field at High Angles-of-attack

NASA Lewis is currently engaged in a research effort as a team member of the High Alpha Technology Program (HATP) within NASA. This program utilizes a specially equipped F/A-18A, the High Alpha Research Vehicle (HARV), in an ambitious effort to improve the maneuverability of high performance military aircraft at low subsonic speed, high angle of attack conditions. The overall objective of the Lewis effort is to develop inlet technology that will ensure efficient airflow delivery to the engine during these maneuvers. One part of the Lewis approach utilizes computational fluid dynamics codes to predict the installed performance of inlets for these highly maneuverable aircraft. Wind tunnel tests were a major component of the Lewis program. Since the available wind tunnel was small (9 x 15 ft) as compared to the scale of the model of the F/A-18A (19.78 percent), there were questions about the capability to obtain useful inlet performance data. The blockage effects were expected to be very large. This report represents the results of an analysis to determine how the wind tunnel walls effect inlet performance at several angles of attack. The predictions for the external particle traces along the fuselage indicate the influence of the wind tunnel side wall under the model is greater at 30 deg angle of attack than at 50 deg angle of attack on the under Leading Edge Extension (LEX) vortex trajectory. The side wall above the model appears to have negligible influence on the under LEX vortex. This may be due to the LEX acting as 'shield' to the upper wall effects. As expected, the wind tunnel has a significant influence on the external forces. The lift and drag coefficients increase significantly for the wind tunnel model as compared to free stream conditions. The wind tunnel had a small effect on the inlet recovery and on inlet total pressure distortion patterns. The predicted recoveries for the wind tunnel model are within one percentage point of the model recoveries in free stream conditions.

Smith, Crawford F.↗

NASA NTRS1997

Turbulent Premixed Flame Propagation in Microgravity

A facility in which turbulent Couette flow could be generated in a microgravity environment was designed and built. To fit into the NASA Lewis drop tower the device had to be very compact. This means that edge effects and flow re-circulation were expected to affect the flow. The flow was thoroughly investigated using LDV and was found to be largely two dimensional away from the edges with constant turbulence intensities in the core. Slight flow asymmetries are introduced by the non symmetric re-circulation of the fluid outside the test region. Belt flutter problems were remedied by adding a pair of guide plates to the belt. In general, the flow field was found to be quite similar to previously investigated Couette flows. However, turbulence levels and associated shear stresses were higher. This is probably due to the confined re-circulation zone reintroducing turbulence into the test section. An estimate of the length scales in the flow showed that the measurements were able to resolve nearly all the length scales of interest. Using a new LES method for subgrid combustion it has been demonstrated that the new procedure is computational feasible even on workstation type environment. It is found that this model is capable of capturing the propagation of the premixed names by resolving the flame in the LES grid within 2-3 grid points. In contrast, conventional LES results in numerical smearing of the flame and completely inaccurate estimate of the turbulent propagation speed. Preliminary study suggests that there is observable effect of buoyancy in the 1g environment suggesting the need for microgravity experiments of the upcoming experimental combustion studies. With the cold flow properties characterized, an identical hot flow facility is under construction. It is assumed that the turbulence properties ahead of the flame in this new device will closely match the results obtained here. This is required since the hot facility will not enable LDV measurements. The reacting flow facility is also being constructed with planned drop tower experiments in mind. Therefore, issues related to safety and structural integrity are being take into account. Further development of the numerical model will also be carried out to include finite-rate kinetics for representative premixed cases. More detail analysis of the flame structure and propagation nature will be investigated. Simulations will also be compared to the flame properties observed in the experiments.

Menon, S.↗

NASA NTRS2000

Development of Ceramic Matrix Composite Turbine Blisks for Rocket Engines

Ceramic matrix composite (CMC) integrally bladed turbine disks (blisks) are being considered for use in various advanced propulsion systems for space vehicles. The successful development of this technology can significantly impact National Aeronautics and Space Administration (NASA) space transportation missions, by enabling new efficient systems that can operate at higher temperatures, while reducing costs. Composite blisks comprised of carbon (C) fibers and a silicon carbide (SiC) ceramic matrix were designed, fabricated, characterized, and tested by a multidisciplinary team involving materials, design, structural analysis, turbomachinery, and nondestructive evaluation representatives from government, academia, and industry during a 4.5 year effort led by the NASA Marshall Space Flight Center (MSFC). The testing of several of these blisks, which were developed in the Simplex Turbopump CMC Blisk ]Program for use in rocket engine turbopumps, was recently completed. CMC blisks offer potential advantages in rocket engine turbopumps including increased safety resulting from increased operating temperature margins and greater pump reliability, and decreased costs resulting from improved turbopump performance. The progress that was achieved in that development effort is reviewed, and some of the technology that could be applied to other advanced space transportation propulsion systems is discussed.

Effinger, Mike↗

NASA NTRS2002

Formation metrology and control for large separated optics space telescopes

In this paper we present formation flying performance analysis initial results for a representative large space telescope composed of separated optical elements [Mett 02]. A virtual-structure construct (an equivalent rigid body) is created by unique metrology and control that combines both centralized and decentralized methods. The formation may be in orbit at GEO for super-resolution Earth observation, as in the case of Figure 1, or it may be in an Earth-trailing orbit for astrophysics, Figure 2. Extended applications are envisioned for exo-solar planet interferometric imaging by a formation of very large separated optics telescopes, Figure 3. Space telescopes, with such large apertures and f/10 to f/100 optics, are not feasible if connected by massive metering structures. Instead, the new virtual-structure paradigm of information and control connectivity between the formation elements provides the necessary spatial rigidity and alignment precision for the telescope.

formation flying virtual-structure telescopes↗

NASA NTRS2007

NASA Langley's Approach to the Sandia's Structural Dynamics Challenge Problem

The objective of this challenge is to develop a data-based probabilistic model of uncertainty to predict the behavior of subsystems (payloads) by themselves and while coupled to a primary (target) system. Although this type of analysis is routinely performed and representative of issues faced in real-world system design and integration, there are still several key technical challenges that must be addressed when analyzing uncertain interconnected systems. For example, one key technical challenge is related to the fact that there is limited data on target configurations. Moreover, it is typical to have multiple data sets from experiments conducted at the subsystem level, but often samples sizes are not sufficient to compute high confidence statistics. In this challenge problem additional constraints are placed as ground rules for the participants. One such rule is that mathematical models of the subsystem are limited to linear approximations of the nonlinear physics of the problem at hand. Also, participants are constrained to use these models and the multiple data sets to make predictions about the target system response under completely different input conditions. Our approach involved initially the screening of several different methods. Three of the ones considered are presented herein. The first one is based on the transformation of the modal data to an orthogonal space where the mean and covariance of the data are matched by the model. The other two approaches worked solutions in physical space where the uncertain parameter set is made of masses, stiffnesses and damping coefficients; one matches confidence intervals of low order moments of the statistics via optimization while the second one uses a Kernel density estimation approach. The paper will touch on all the approaches, lessons learned, validation 1 metrics and their comparison, data quantity restriction, and assumptions/limitations of each approach. Keywords: Probabilistic modeling, model validation, uncertainty quantification, kernel density

Horta, Lucas G.↗