Search NASA⌕ Search

SEARCH · Search NASA

Results for “separability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Separation of Americium in High Oxidation States from Curium Utilizing Sodium Bismuthate

A simple separation of americium from curium would support closure of the nuclear fuel cycle, assist in nuclear forensic analysis, and allow for more accurate measurement of neutron capture properties of 241 Am. Methods for the separation of americium from curium are however complicated and time-consuming due to the similar chemical properties of these elements. In this work a novel method for the separation of americium from curium in nitric acid media was developed using sodium bismuthate to perform both the oxidation and separation. Sodium bismuthate is shown to be a promising material for performing a simple and rapid separation. Curium is more strongly retained than americium on the undissolved sodium bismuthate at nitric acid concentrations below 1.0 M. A separation factor of ~90 was obtained in 0.1 M nitric acid. This separation factor is achieved within the first minute of contact and is maintained for at least 2 h of contact. Separations using sodium bismuthate were performed using solid–liquid extraction as well as column chromatography.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Centrifugal Length Separation of Carbon Nanotubes

Separation of single-wall carbon nanotubes (SWCNTs) by length via centrifugation in a high density medium, and the characterization of both the separated fractions and the centrifugation process are presented. Significant quantities of the separated SWCNTs ranging in average length from < 50 nm to ~2 μm were produced, with the distribution width being coupled to the rate of the separation. Less rapid separation is shown to produce narrower distributions; these length fractions, produced using sodium deoxycholate dispersed SWCNTs, were characterized by UV-visible-nearinfrared absorption and fluorescence spectroscopy, dynamic light scattering, Raman scattering, and atomic force microscopy. Several parameters of the separation were additionally explored: SWCNT concentration, added salt concentration, liquid density, rotor speed, surfactant concentration, and the processing temperature. The centrifugation technique is shown to support 10 mg per day scale processing and is applicable to all of the major SWCNT production methods. The cost per unit of the centrifugation-based separation is also demonstrated to be significantly less than size exclusion chromatography-based separations.

36 MATERIALS SCIENCE↗

Killing tensors, warped products and the orthogonal separation of the Hamilton-Jacobi equation

We study Killing tensors in the context of warped products and apply the results to the problem of orthogonal separation of the Hamilton-Jacobi equation. This work is motivated primarily by the case of spaces of constant curvature where warped products are abundant. We first characterize Killing tensors which have a natural algebraic decomposition in warped products. We then apply this result to show how one can obtain the Killing-Stäckel space (KS-space) for separable coordinate systems decomposable in warped products. This result in combination with Benenti's theory for constructing the KS-space of certain special separable coordinates can be used to obtain the KS-space for all orthogonal separable coordinates found by Kalnins and Miller in Riemannian spaces of constant curvature. Next we characterize when a natural Hamiltonian is separable in coordinates decomposable in a warped product by showing that the conditions originally given by Benenti can be reduced. Finally, we use this characterization and concircular tensors (a special type of torsionless conformal Killing tensor) to develop a general algorithm to determine when a natural Hamiltonian is separable in a special class of separable coordinates which include all orthogonal separable coordinates in spaces of constant curvature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental Demonstration of Advanced Palladium Membrane Separators for Central High Purity Hydrogen Production

The overall objectives for this project were to: (1) confirm the high stability and resistance of a PdCu trimetallic alloy to carbon and carbide formation and, in addition, resistance to sulfur, halides, and ammonia; (2) develop a sulfur, halide, and ammonia resistant alloy membrane with a projected hydrogen permeance of 25 m{sup 3}m{sup -2}atm{sup -0.5}h{sup -1} at 400 C and capable of operating at pressures of 12.1 MPa ({approx}120 atm, 1750 psia); and (3) construct and experimentally validate the performance of 0.1 kg/day H{sup 2} PdCu trimetallic alloy membrane separators at feed pressures of 2 MPa (290 psia) in the presence of H{sub 2}S, NH{sub 3}, and HCl. This project successfully increased the technology readiness level of palladium-based metallic membranes for hydrogen separation from coal-biomass gasifier exhaust or similar hydrogen-containing gas streams. The reversible tolerance of palladium-copper (PdCu) alloys was demonstrated for H{sub 2}S concentrations varying from 20 ppmv up to 487 ppmv and NH{sub 3} concentrations up to 9 ppmv. In addition, atomistic modeling validated the resistance of PdCu alloys to carbon formation, irreversible sulfur corrosion, and chlorine attack. The experimental program highlighted two key issues which must be addressed as part of future experimental programs: (1) tube defects and (2) non-membrane materials of construction. Four out of five FCC PdCu separators developed leaks during the course of the experimental program because {approx}10% of the alloy tubes contained a single defect that resulted in a thin, weak point in the tube walls. These defects limited operation of the existing tubes to less than 220 psig. For commercial applications of a PdCu alloy hydrogen separator under high sulfur concentrations, it was determined that stainless steel 316 is not suitable for housing or supporting the device. Testing with sulfur concentrations of 487 {+-} 4 ppmv resulted in severe corrosion of the stainless steel components of the separators. The project identified an experimental methodology for quantifying the impact of gas contaminants on PdCu alloy membrane performance as well as an atomistic modeling approach to screen metal alloys for their resistance to irreversible sulfur corrosion. Initial mathematical descriptions of the effect of species such as CO and H{sub 2}S were developed, but require further experimental work to refine. At the end of the project, an improvement to the experimental approach for acquiring the necessary data for the permeability model was demonstrated in preliminary tests on an enhanced PdCu separator. All of the key DOE 2010 technical targets were met or exceeded except for the hydrogen flux. The highest flux observed for the project, 125 ft{sup 3}ft{sup -2}h{sup -1}, was obtained on a single tube separator with the aforementioned enhanced PdCu separator with a hydrogen feed pressure of 185 psig at 500 C.

08 HYDROGEN↗

Final summarizing report on Grant DE-SC0001014 "Separation of Highly Complex Mixtures by Two-dimension Liquid Chromatography"

The goal of our research was a fundamental investigation of methods available for the coupling of two separate chromatographic separations that would considerably enhance the individual separation power of each of these two separations. This gain arises from the combination of two independent retention mechanisms, one of them separating the components that coelute on the other column, making possible the separation of many more compounds in a given time. The two separation mechanisms used must be very different. This is possible because many retention mechanisms are available, using different kinds of molecular interactions, hydrophobic or hydrophilic interactions, polar interactions, hydrogen bonding, complex formation, ionic interactions, steric exclusion. Two methods can be used, allowing separations to be performed in space (spreading the bands of sample components on a plate covered with stationary phase layer) or in time (eluting the sample components through a column and detecting the bands leaving the column). Both offer a wide variety of possible combinations and were studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The mechanics of pressed-pellet separators in molten salt batteries

We present a phenomenological constitutive model that describes the macroscopic behavior of pressed-pellet materials used in molten salt batteries. Such materials include separators, cathodes, and anodes. The purpose of this model is to describe the inelastic deformation associated with the melting of a key constituent, the electrolyte. At room temperature, all constituents of these materials are solid and do not transport cations so that the battery is inert. As the battery is heated, the electrolyte, a constituent typically present in the separator and cathode, melts and conducts charge by flowing through the solid skeletons of the anode, cathode, and separator. The electrochemical circuit is closed in this hot state of the battery. The focus of this report is on the thermal-mechanical behavior of the separator, which typically exhibits the most deformation of the three pellets during the process of activating a molten salt battery. Separator materials are composed of a compressed mixture of a powdered electrolyte, an inert binder phase, and void space. When the electrolyte melts, macroscopically one observes both a change in volume and shape of the separator that depends on the applied boundary conditions during the melt transition. Although porous flow plays a critical role in the battery mechanics and electrochemistry, the focus of this report is on separator behavior under flow-free conditions in which the total mass of electrolyte is static within the pellet. Specific poromechanics effects such as capillary pressure, pressure-saturation, and electrolyte transport between layers are not considered. Instead, a phenomenological model is presented to describe all such behaviors including the melting transition of the electrolyte, loss of void space, and isochoric plasticity associated with the binder phase rearrangement. The model is appropriate for use finite element analysis under finite deformation and finite temperature change conditions. The model reasonably describes the stress dependent volume and shape change associated with dead load compression and spring-type boundary conditions; the latter is relevant in molten salt batteries. Future work will transition the model towards describing the solid skeleton of the separator in the traditional poromechanics context.

25 ENERGY STORAGE↗

Advanced Aqueous Separation Systems for Actinide Partitioning

One of the most challenging aspects of advanced processing of used nuclear fuel is the separation of transplutonium actinides from fission product lanthanides. This separation is essential if actinide transmutation options are to be pursued in advanced fuel cycles, as lanthanides compete with actinides for neutrons in both thermal and fast reactors, thus limiting efficiency. The separation is difficult because the chemistry of Am 3+ and Cm 3+ is nearly identical to that of the trivalent lanthanides (Ln 3+ ). The prior literature teaches that two approaches offer the greatest probability of devising a successful group separation process based on aqueous processes: 1) the application of complexing agents containing ligand donor atoms that are softer than oxygen (N, S, Cl - ) or 2) changing the oxidation state of Am to the IV, V, or VI state to increase the essential differences between Am and lanthanide chemistry (an approach utilized in the PUREX process to selectively remove Pu 4+ and UO 2 2+ from fission products). The latter approach offers the additional benefit of enabling a separation of Am from Cm, as Cm(III) is resistant to oxidation and so can easily be made to follow the lanthanides. The fundamental limitations of these approaches are that 1) the soft(er) donor atoms that interact more strongly with actinide cations than lanthanides form substantially weaker bonds than oxygen atoms, thus necessitating modification of extraction conditions for adequate phase transfer efficiency, 2) soft donor reagents have been seen to suffer slow phase transfer kinetics and hydro-/radiolytic stability limitations and 3) the upper oxidation states of Am are all moderately strong oxidants, hence of only transient stability in media representative of conventional aqueous separations systems. There are examples in the literature of both approaches having been described. However, it is not clear at present that any extant process is sufficiently robust for application at the scale necessary for commercial fuel processing supporting transmutation of transplutonium elements. This research project continued basic themes investigated by this research group during the past decade. In the Fuel Cycle Research and Development program at DOE, the current favorite process for accomplishing the separation of trivalent actinides from fission product lanthanides is the TALSPEAK process. TALSPEAK is a solvent extraction method (developed at Oak Ridge National Lab in the 1960s) based on the combination of a cation exchanging extractant (e.g., HDEHP), an actinide-selective aminopolycarboxylate complexing agent (e.g., DTPA), and a carboxylic acid buffer to control pH in the range of 3-4. Considerable effort has been expended in this research group during the past 8 years to elaborate the details of TALSPEAK in the interest of developing improved approaches to the operation of TALSPEAK-like systems. In this project we focused on defining aggregation phenomena in conventional TALSPEAK separations, on supporting the development of Advanced TALSPEAK processes, on profiling the aqueous complexation kinetics of lanthanides in TALSPEAK relevant aqueous media, on the design of new diglycolamide and N-donor extractants, and on characterizing cation-cation complexes of pentavalent actinides.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Rare earth separation in voltage-gated 2D MXene membranes

The separation of rare earth elements (REEs) has historically been a complicated and expensive process, producing significant amounts of pollution. To this end, MXene membranes (MXMs) have attracted researchers' interest. It has been demonstrated that MXMs are capable of separating ions and that it is possible to precisely control the separation rate by applying a voltage to the membrane. Indeed, due to their chemical nature, MXenes show outstanding electrical conductivity. However, the effect of applied voltage on the permeation rate and separation effects of iconic species remains an intriguing area of research. In this work, we demonstrate how applying different voltages (gate voltage) to a MXM affects the permeation rate of various REE ions. Our hypothesis to explain MXMs behavior towards REE is that under negative voltage, the interlayer spacing decreases due to attraction between charged MXene surfaces and intercalated cations, increasing the separation factor between REEs. Under positive voltage, the interlayer spacing increases due to repulsion between the MXene surfaces and intercalated cations. However, we demonstrate relatively poor separation capability for REEs at 1mM starting concentration and 1.0 V applied DC voltage (separation factor ~1-3). This study demonstrates the need for future experiments to observe varied experimental conditions and chemical functionalization to determine whether MXene membranes can be an efficient platform for REE separation.

36 MATERIALS SCIENCE↗

Decarb/Desal: Separation of Carbon Dioxide from Flue Gas with Simultaneous Fresh Water Production

If fossil fuels continue to be a major part of the world's energy supply, effective means must be developed to deal with the carbon emissions. Geologic sequestration of supercritical CO{sub 2} is expected to play a major role in mitigating this problem. Separating carbon dioxide from other gases is the most costly aspect of schemes for geologic sequestration. That cost is driven by the complexity and energy intensity of current chemical-stripping methods for separating carbon dioxide. Our experience in water treatment technology indicated that an entirely new approach could be developed, taking advantage of water's propensity to separate gases that ionize in water (like CO{sub 2}) from those that do not (like N{sub 2}). Even though water-based systems might not have the extreme selectivity of chemicals like substituted amines used in industrial systems today, they have the potential to tolerate NO{sub x}, SO{sub x}, and particulates while also producing clean drinking water as a valuable byproduct. Lower capital cost, broader range of applicability, environmental friendliness, and revenue from a second product stream give this approach the potential to significantly expand the worldwide application of carbon separation for geologic sequestration. Here we report results for separation of CO{sub 2} from flue gas by two methods that simultaneously separate carbon dioxide and fresh water: ionic pumping of carbonate ions dissolved in water, and thermal distillation. The ion pumping method dramatically increases dissolved carbonate ion in solution and hence the overlying vapor pressure of CO{sub 2} gas, allowing its removal as a pure gas. We have used two common water treatment methods to drive the ion pumping approach, reverse osmosis and electrodialysis to produce pure CO{sub 2}. This novel approach to increasing the concentration of the extracted gas permits new approaches to treating flue gas, because the slightly basic water used as the extraction medium is impervious to trace acid gases that destroy existing solvents, and no pre-separation is necessary. Thermal distillation uses boiling water to steam strip solid sorbents - the steam is recovered as fresh water. We anticipate that our method will compete favorably with current chemical stripping systems used for CO{sub 2} separation at power plants, which incur a 35% energy penalty. Thus we expect to offer a dramatically improved solution for removing carbon from hydrocarbon combustion. Our method can be demonstrated on small sources, which will enable us to conduct the demonstrations required to build confidence in the method. If successful, we will be in a position to advance a follow-on proposal for a demonstration at the 10-MW scale.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Design of Multi-Stage Solvent Extraction Process for Separation of Rare Earth Elements

Flowsheet design and stage determination for the separation of rare earth elements (REEs) using solvent extraction (SX) is a challenging task because of the chemical similarity of the REEs. Low separation factors between the elements and complex equilibrium chemistry provide unique challenges to designing an efficient flowsheet for the separation of elements. The multi-stage nature of the SX process adds further complexity, making the assessment of products for a proposed design and stage combination difficult. Therefore, to develop a SX flowsheet, it is essential to quantify the performance for various design and separation conditions. This paper attempts to address the challenge by utilizing an equilibrium and process modeling approach. Results from a bench-scale study performed on a 10 g/L rare earth salt mixture were used in studying the extraction/stripping behavior and developing equilibrium models. DEHPA with TBP as a phase modifier was used as an extractant, while hydrochloric acid was utilized as a stripping agent. The results obtained were used in developing extraction/stripping models, which were integrated into a process framework of a SX train in a Matlab/Simulink environment. The models were programmed as a function block routine and used for developing a flowsheet, which was simulated for differing separation and design conditions. To identify optimum stage combinations, a particle swarm optimization (PSO) routine was developed and implemented for each SX train. Recovery and purity of elements of interest were used as objective function criteria. The stage combination leading to the minimization of the objective function was used to identify the optimum stage combination for a series of SX trains to attempt a balance of purity and recovery. The models and optimization method were implemented to separate a feed mixture containing REEs, which indicated that 99.52 and 85.41 percent purity is achievable for Yttrium and Lanthanum separation using 8-12-3 and 10-3-5 stage combination for loading, scrubbing, and striping. The model also indicated difficult separability between neodymium, praseodymium, and cerium.

Srivastava, Vaibhav (ORCID:0000000212645987)↗

Hydrogen separation process

A method for separating a hydrogen-rich product stream from a feed stream comprising hydrogen and at least one carbon-containing gas, comprising feeding the feed stream, at an inlet pressure greater than atmospheric pressure and a temperature greater than 200.degree. C., to a hydrogen separation membrane system comprising a membrane that is selectively permeable to hydrogen, and producing a hydrogen-rich permeate product stream on the permeate side of the membrane and a carbon dioxide-rich product raffinate stream on the raffinate side of the membrane. A method for separating a hydrogen-rich product stream from a feed stream comprising hydrogen and at least one carbon-containing gas, comprising feeding the feed stream, at an inlet pressure greater than atmospheric pressure and a temperature greater than 200.degree. C., to an integrated water gas shift/hydrogen separation membrane system wherein the hydrogen separation membrane system comprises a membrane that is selectively permeable to hydrogen, and producing a hydrogen-rich permeate product stream on the permeate side of the membrane and a carbon dioxide-rich product raffinate stream on the raffinate side of the membrane. A method for pretreating a membrane, comprising: heating the membrane to a desired operating temperature and desired feed pressure in a flow of inert gas for a sufficient time to cause the membrane to mechanically deform; decreasing the feed pressure to approximately ambient pressure; and optionally, flowing an oxidizing agent across the membrane before, during, or after deformation of the membrane. A method of supporting a hydrogen separation membrane system comprising selecting a hydrogen separation membrane system comprising one or more catalyst outer layers deposited on a hydrogen transport membrane layer and sealing the hydrogen separation membrane system to a porous support.

08 HYDROGEN↗

Methods and materials for determination of distribution coefficients for separation materials

Methods and materials for determining the affinity of separation materials for targeted species are described. A composite separation medium is described that combines a separation material such as an ion exchange material or a sorbent with an SERS substrate. Methods and materials can be utilized to determine the distribution coefficient of a species for a separation material after running a single separation protocol followed by examination of the separation material of the protocol according to SERS. Disclosed methods can be utilized to determine the affinity of existing separation materials for targeted species as well as to determine the affinity of newly engineered separation materials to characterize species.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Use of Separator with Regular Granular Filling in Extraction Processes - 12209

The separator with a regular granular filling has been developed to be used for the operations of the removal of carbon-black impurities from the aqueous flow; the intra-cycle regeneration of back-extractants; and the concentrating back-extraction of plutonium in the extraction SNF reprocessing technology. The process conditions for those operations have been experimentally tested using this separator. Thus, the separator for operations of concentrating reextraction of plutonium and regeneration recycling extractant allows to: - derive plutonium from the organic stream into an extremely concentrated form, reducing the amount of liquid radioactive waste (raffinate, decantate) plutonium branches to a minimum; - controlling the processes of concentration of uranium and plutonium, get uranium-plutonium product with required concentration and the amount of metal with required ratio; - eliminate contamination of the emulsion flows; - simplify the purification of uranium from the extract plutonium; - test results showed that when working on a solution 'hydrazine-DTPA' in the separator it is achieved the extraction of plutonium re-extract - 82% TC - at 56-65%. With the transition to the reextraction by solution 'U (IV)-hydrazine', of plutonium into re-extract increases to 95%, technetium - up to 83%; - regenerate the extractant recycling minimizing the amount of liquid radioactive waste generated as a technology used as well as alternative 'salt-free' systems; - it is found that the regeneration of the extractant solution of soda and EDA in the separator at a load of 3.2 m{sup 3} / (m{sup 2}.h) it can be achieved almost complete phase separation. Residual carryover of 0,005-0,006% emulsion is on the verge of analytical detection. - It is shown that in the depth of separation phase a separation of the extractant regeneration of quality superior is more than 5-7 times to the extraction. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Separator Effect on Zinc Electrodeposition Behavior and Its Implication for Zinc Battery Lifetime

We report uncontrolled zinc electrodeposition is an obstacle to long-cycling zinc batteries. Much has been researched on regulating zinc electrodeposition, but rarely are the studies performed in the presence of a separator, as in practical cells. Here, we show that the microstructure of separators determines the electrodeposition behavior of zinc. Porous separators direct zinc to deposit into their pores and leave “dead zinc” upon stripping. In contrast, a nonporous separator prevents zinc penetration. Such a difference between the two types of separators is distinguished only if caution is taken to preserve the attachment of the separator to the zinc-deposited substrate during the entire electrodeposition–morphological observation process. Failure to adopt such a practice could lead to misinformed conclusions. Our work reveals the mere use of porous separators as a universal yet overlooked challenge for metal anode-based rechargeable batteries. Countermeasures to prevent direct exposure of the metal growth front to a porous structure are suggested.

25 ENERGY STORAGE↗

Separating Oil-Water Mixtures Using Bump Arrays

Particle separation is an important process step across many fields. One technique being applied for separating solids such as blood components or sand particles from carrier fluids is the use of arrays of aligned posts called deterministic lateral arrays to bump particles to one side in the flow stream to enhance separation. This technique may be useful for separation of deformable particles. The ability to efficiently separate two-phase industrial (oil/water) mixtures is key for future use of valuable resources. Over 1 trillion gallons of petroleum production water could be reclaimed annually for reuse in the drought-ridden western US states. The ability to reclaim this petroleum production water may be critical for the Central High Plains (Colorado, Kansas, Oklahoma, Texas, and New Mexico). Trends in just the High Plains area already lost 20 to 25% of the irrigated farming area due to insufficient ground water storage to irrigate, and farmland losses are expected to grow to 40%. Proving this technology is key to reuse of petroleum production water for crop irrigation or to replace water from currently failing aquifers in rich agricultural lands of the Central High Plains. We conducted experiments applying mesofluidic separation for flowing two-phase (oil/water) mixtures. Experiments were conducted using oils of differing viscosities with water as the carrier fluid; separation was achieved over a range of oil-water concentrations. We describe the results of these experiments in this paper.

oil-water separation, micelle, droplet separation,↗

Simple Bioparticle Filtration Device Based on an Ultralow-Fouling Zwitterionic Polyurethane Membrane for Rapid Large-Volume Separation of Plasma and Viruses from Whole Blood

Plasma separation from whole blood is oftent required as an essential first step when performing blood tests with a viral assay. However, developing a point-of-care plasma extraction device with a large output and high virus recovery remains a significant obstacle to the success of on-site viral load tests. Here, we report a portable, easy-to-use, cost-efficient, membrane-filtration-based plasma separation device that enables rapid large-volume plasma extraction from whole blood, designed for point-of-care virus assays. The plasma separation is realized by a low-fouling zwitterionic polyurethane-modified cellulose acetate (PCBU-CA) membrane. The zwitterionic coating on the cellulose acetate membrane can decrease surface protein adsorption by 60% and increase plasma permeation by 46% compared with a pristine membrane. The PCBU-CA membrane, with its ultralow-fouling properties, enables rapid plasma separation. The device can yield a total of 1.33 mL plasma from 10 mL whole blood in 10 min. The extracted plasma is cell-free and exhibits a low hemoglobin level. In addition, our device demonstrated a 57.8% T7 phage recovery in the separated plasma. The results of real-time polymerase chain reaction analysis confirmed that the nucleic acid amplification curve of the plasma extracted by our device is comparable to that obtained by centrifugation. With its high plasma yield and good phage recovery, our plasma separation device provides an excellent replacement for traditional plasma separation protocols for point-of-care virus assays and a broad spectrum of clinical tests.

36 MATERIALS SCIENCE↗

Important Role of Ion Flux Regulated by Separators in Lithium Metal Batteries

Abstract Polyolefin separators are the most common separators used in rechargeable lithium (Li)‐ion batteries. However, the influence of different polyolefin separators on the performance of Li metal batteries (LMBs) has not been well studied. By performing particle injection simulations on the reconstructed three‐dimensional pores of different polyethylene separators, it is revealed that the pore structure of the separator has a significant impact on the ion flux distribution, the Li deposition behavior, and consequently, the cycle life of LMBs. It is also discovered that the homogeneity factor of Li‐ion toward Li metal electrode is positively correlated to the longevity and reproducibility of LMBs. This work not only emphasizes the importance of the pore structure of polyolefin separators but also provides an economic and effective method to screen favorable separators for LMBs.

25 ENERGY STORAGE↗

Nanofiltration Membranes for Li + /Mg 2+ Separation: Materials and Mechanisms

Nanofiltration (NF) membranes have garnered significant interest for Li + /Mg 2+ separation, a crucial step in lithium extraction from brines. The state-of-the-art commercial LiNE-XD membrane exhibits a Li + /Mg 2+ separation factor (SF Li/Mg ) of 42 at pH 3.3, due to the positive charges on the membrane surface and its strong size-sieving ability. Membranes with higher separation factors at a broad pH range are being pursued to improve separation efficiency. This work aims to provide a timely and comprehensive assessment of advanced NF membranes with superior Li + /Mg 2+ separation properties, as well as their structure and property relationships for designing next-generation membranes. We describe transport mechanisms for ions in NF membranes and discuss governing parameters and models employed to quantify the Li + /Mg 2+ separation. High-performance membrane materials are exhaustively introduced, including commercial and modified polyamides, two-dimensional materials, metal–organic frameworks, crown ethers, and their blends. Finally, we critically compare these membranes in an upper bound plot and highlight the opportunities and challenges of NF membranes for practical Li + /Mg 2+ separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗