Search NASA⌕ Search

SEARCH · Search NASA

Results for “separator modification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Weak double layers in the auroral ionosphere

Previous work on the evolution of weak double layers in a hydrogen plasma was extended to include H(+) and O(+) with relative drift. The relative drift between hydrogen and oxygen ions due to a quasi-static parallel electric field gives rise to a strong linear fluid instability which dominates the ion-acoustic mode at the bottom of the auroral acceleration region. This ion-ion instability can modify ion distributions at lower altitudes and the subsequent nonlinear evolution of weak double layers at higher altitudes in the ion-acoustic regime. Ion hole formation can occur for smaller relative electron-ion drifts than seen in previous simulations, due to the hydrogen-oxygen two-stream instability. This results in local modification of the ion distributions in phase space, and a partial filling of the valley between the hydrogen and oxygen peaks, which would be expected at higher altitudes on auroral field lines. The observed velocity diffusion does not necessarily preclude ion hole and double layer formation in hydrogen in the ion-acoustic regime. These simulation results are consistent with the experimentally measured persistence of separate hydrogen and oxygen peaks, and the observation of weak double layers above an altitude of 3000 km on auroral field lines.

Hudson, M. K.↗

An Investigation of the Pitching-Moment Contribution of a High Horizontal Tail on an Unswept-Wing and Body Combination at Mach Numbers from 0.80 to 1.40

An investigation has been conducted to determine the effects of a high positioned horizontal tail on a wing-body configuration having a thin unswept wing of aspect ratio 3.09. Lift and pitching-moment coefficients were obtained for Mach numbers from 0.80 to 1.40 at Reynolds numbers of 1.0 and 1.5 million and for angles of attack to 20 deg. An experimental study of the pitching-moment contribution of the horizontal tail indicated that the marked destabilizing effect of the horizontal tail at high angles of attack for Mach numbers of 0.80 to 1.00 was associated with the formation of completely separated flow on the upper surface of the wing. Computations of the interference effects of the wing-body combination on the tail for Mach numbers of 0.80 and 0.94 and high angles of attack confirmed this conclusion. For a Mach number of 1.40, and high angles of attack, computations disclosed that the destabilizing effect primarily resulted from the trailing vortices of the wing. Two modifications to the basic wing plan form, which consisted of chord extensions, were generally unsuccessful in reducing the destabilizing contributions of the horizontal tail at high angles of attack.

Lippmann, Garth W.↗

Tailoring the Coordination Micro‐Environment in Nanotraps for Efficient Platinum/Palladium Separation

Abstract Recovering platinum group metals from secondary resources is crucial to meet the growing demand for high‐tech applications. Various techniques are explored, and adsorption using porous materials has emerged as a promising technology due to its efficient performance and environmental beingness. However, the challenge lies in effectively recovering and separating individual platinum group metals (PGMs) given their similar chemical properties. Herein, a breakthrough approach is presented by sophisticatedly tailoring the coordination micro‐environment in a series of aminopyridine‐based porous organic polymers, which enables the creation of platinum‐specific nanotraps for efficient separation of binary PGMs (platinum/palladium). The newly synthesized POP‐o2NH 2 ‐Py demonstrates record uptakes and selectivity toward platinum over palladium, with the amino groups adjacent to the pyridine moieties being vital in improving platinum binding performance. Further breakthrough experiments underline its remarkable ability to separate platinum and palladium. Spectroscopic analysis reveals that POP‐o2NH 2 ‐Py offers a more favorable coordination fashion to platinum ions compared to palladium ions owing to the greater interaction between N and Pt 4+ and stronger intramolecular hydrogen bonding between the amino groups and four coordinating chlorines at platinum. These findings underscore the importance of fine‐tuning the coordination micro‐environment of nanotraps through subtle modifications that can greatly enhance the selectivity toward the desired metal ions.

Chemistry↗

Rheology of lignin and lignin-based solutions, dispersions, gels, polymer blends, and melts

Lignin is an abundant resource that finds application in energy and sustainable materials development. In addition to the utilization of lignin in three-dimensional (3D) printing and hydrogel production, recent studies have reported the use of lignin as a liquid fuel additive. The characterization of the rheological properties of lignin and its derivatives is a dynamic and evolving field, underpinned by advances in experimental, analytical, and modeling techniques. Here, this review provides a comprehensive overview of the recent progress in the study of lignin rheology, highlighting the interplay between structure, modification, and flow behavior in lignin-based solutions, dispersions, gels, polymer blends, and melts. A specific highlight of this review is how lignin concentration affects the rheological properties of lignin-based solutions and dispersions. Furthermore, the effect of lignin type on the properties of 3D-printed lignin-based composites is discussed. For polymer systems, this review discussed lignin-in-polymer solutions separately from lignin-filled polymer systems. Finally, challenges and perspectives on lignin rheology are presented.

Dispersions↗

A theoretical and experimental study of turbulent evaporating sprays

Measurements and analysis limited to the dilute portions of turbulent evaporating sprays, injected into a still air environment were completed. Mean and fluctuating velocities and Reynolds stress were measured in the continuous phase. Liquid phase measurements included liquid mass fluxes, drop sizes and drop size and velocity correlation. Initial conditions needed for model evaluation were measured at a location as close to the injector exit as possible. The test sprays showed significant effects of slip and turbulent dispersion of the discrete phase. The measurements were used to evaluate three typical models of these processes: (1) a locally homogeneous flow (LHF) model, where slip between the phases were neglected; (2) a deterministic separated flow (DSF) model, where slip was considered but effects of drop dispersion by turbulence were ignored; and (3) a stochastic separated flow (SSF) model, where effects of interphase slip and turbulent dispersion were considered using random-walk computations for drop motion. For all three models, a k-epsilon model as used to find the properties of the continuous phase. The LHF and DSF models did not provide very satisfactory predictions for the present measurements. In contrast, the SSF model performed reasonably well--with no modifications in the prescription of eddy properties from its original calibration.

Solomon, A. S. P.↗

An aerodynamic analysis computer program and design notes for low speed wing flap systems

The expanded capabilities for analysis and design of low speed flap systems afforded by recent modifications of an existing computer program is described. The program provides for the simultaneous analysis of up to 25 pairs of leading-edge and trailing-edge flap deflection schedules. Among other new features of the program are a revised attainable thrust estimation method to provide more accurate predictions for low Mach numbers, and a choice of three options for estimation of leading-edge separation vortex flow effects. Comparison of program results with low speed experimental data for an arrow wing supersonic cruise configuration with leading-edge and trailing-edge flaps showed good agreement over most of the range of flap deflections. Other force data comparisons and an independent study of airfoil and wing pressure distributions indicated that wind-tunnel measurements of the aerodynamic performance of twisted and cambered wings and wings with leading-edge flaps can be very sensitive to Reynolds number effects.

Carlson, H. W.↗

A Numerical Study of Anti-Vortex Film Cooling Designs at High Blowing Ratio

A concept for mitigating the adverse effects of jet vorticity and liftoff at high blowing ratios for turbine film cooling flows has been developed and studied at NASA Glenn Research Center. This "anti-vortex" film cooling concept proposes the addition of two branched holes from each primary hole in order to produce a vorticity counter to the detrimental kidney vortices from the main jet. These vortices typically entrain hot freestream gas and are associated with jet separation from the turbine blade surface. The anti-vortex design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The anti-vortex film cooling hole concept has been modeled computationally for a single row of 30deg angled holes on a flat surface using the 3D Navier-Stokes solver Glenn-HT. A modification of the anti-vortex concept whereby the branched holes exit adjacent to the main hole has been studied computationally for blowing ratios of 1.0 and 2.0 and at density ratios of 1.0 and 2.0. This modified concept was selected because it has shown the most promise in recent experimental studies. The computational results show that the modified design improves the film cooling effectiveness relative to the round hole baseline and previous anti-vortex cases, in confirmation of the experimental studies.

Heidmann, James D.↗

Metallurgical Research Relating to the Development of Metals and Alloys for Use in the High-Temperature Components of Jet-Engines, Gas Turbines and Other Aircraft Propulsion Systems

Studies are in progress to establish the fundamental processes by which treatment and composition control properties of commercial alloys at high temperatures. Low-Carbon N155 and Inconel-X alloys are being used as indicative of two types of alloys of major interest. Progress has been reported three time previously. The work has been separated into two sections: studies of structures resulting from solu tion treatment and aging and studies of structures resulting from rolling at various temperatures. Brief descriptions of experimental techniques used, results, and interpretation of the data obtained to date are summarized below. Since the work outlined is to a large extent still in progress, the discussion given is to be considered tentative and subject to further modification as additional data becomes available.

Source record↗

STS-114: Discovery Tanking Operations for Launch

Jessica Rye from NASA Public Affairs is the narrator for the tanking operations for the launch of the Space Shuttle Discovery. She presents a video of the arrival and processing of the new external tank at the Kennedy Space Center. The external tank is also shown entering the Vehicle Assembly Building (VAB). The external tank underwent new processing resulting from its redesign including inspection of the bipod heater and the external separation camera. The changes to the external tank include: 1) Electric heaters to protect from icing; and 2) Liquid Oxygen feed line bellows to carry fuel from the external tank to the Orbiter. Footage of the external tank processing facility at NASA's Michoud Assembly Facility in New Orleans, La. prior to its arrival at Kennedy Space Center is shown and a video of the three key modifications to the external tank including the bipod, flange and bellows are shown.

Source record↗

Wind-tunnel investigation of effects of wing-leading-edge modifications on the high angle-of-attack characteristics of a T-tail low-wing general-aviation aircraft

Exploratory tests have been conducted in the NASA-Langley Research Center's 12-Foot Low-Speed wind Tunnel to evaluate the application of wing-leading-edge devices on the stall-departure and spin resistance characteristics of a 1/6-scale model of a T-tail general-aviation aircraft. The model was force tested with an internal strain-gauge balance to obtain aerodynamic data on the complete configuration and with a separate wing balance to obtain aerodynamic data on the outer portion of the wing. The addition of the outboard leading-edge droop eliminated the abrupt stall of the windtip and maintained or increased the resultant-force coefficient up to about alpha = 32 degrees. This change in slope of the resultant-force coefficient curve with angle of attack has been shown to be important for eliminating autorotation and for providing spin resistance.

White, E. R.↗

Surface and bulk two-level-system losses in lithium niobate acoustic resonators

Lithium niobate (LN) is a promising material for building acoustic resonators used in quantum applications, but its performance is limited by poorly understood material defects called two-level systems (TLSs). Here, in this work, we fabricate high-performance acoustic resonators from LN with quality factors up to 6 ×10 7 and use them to separate bulk and surface contributions to TLS loss. By comparing these bulk acoustic wave (BAW) resonators with previous surface-acoustic-wave and phononic-crystal studies, we show that devices with high surface-participation ratios are limited by surface TLSs, while our BAW devices reveal an intrinsic bulk TLS limit. Through systematic surface treatments and microscopy, we demonstrate that BAW resonator performance remains unchanged despite surface modifications, confirming operation in a bulk-limited regime. Here, our work establishes quantitative bounds on both surface and bulk TLS losses in LN within the context of the material growth and fabrication approaches we have pursued, and it provides guidance for future device engineering and materials development.

acoustic wave phenomena↗

Electrospinner Upgrades for Nanofiber Production

Electrospinning is an inexpensive method for producing nanofibers, with applications in accelerator targets, air filtration, and biomedicine. This project aims to upgrade and test an existing roll-to-roll electrospinner that is economical for industrial production. Our unit cannot adjust spinneret to collector separation and thus nanofiber diameter (application dependent). The electro-spinneret channel also does not have lateral adjustment capabilities. Lastly, the viscosities of our polymers have not been quantified, which can inform future injector nozzle designs. Modeling was done with Siemens NX CAD, and viscosity was measured using a Brookfield DVE-LV viscometer. A dual scissor lift design was approved, and construction was started, along with channel modifications. Viscosity measurements of polyvinyldimethylformamide were recorded with inconsistent results. Going forward, the scissor lift and channel modifications will be evaluated with our electrospinner. Future viscosity trials must be completed in accordance with testing requirements. The optimization of electrospinner units can make nanofiber production more feasible for many industries.

Black, Niko↗

A study of the electric field in an open magnetospheric model

The qualitative properties of an open magnetosphere and its electric field are examined and compared to a simple model of a dipole in a constant field and to actual observations. Many of these properties are found to depend on the separatrix, a curve connecting neutral points and separating different field-line regimes. In the simple model, the electric field in the central polar cap tends to point from dawn to dusk for a wide choice of external fields. Near the boundary of the polar cap electric equipotentials curve and become crescent-shaped, which may explain the correlation of polar magnetic variations with the azimuthal component of the interplanetary magnetic field, reported by Svalgaard. Modifications expected to occur in the actual magnetosphere are also investigated: in particular, it appears that bending of equipotentials may be reduced by cross-field flow during the merging of field lines and that open field lines connected to the polar caps emerge from a long and narrow slot extending along the tail.

Stern, D. P.↗

Models of climate cycles recorded in Martian polar layered deposits

Mars polar deposit accumulation models are used to predict the sequences of layer thicknesses. Continuous deposition and climate-modulated deposition models are compared, and two physical models of the latter type are developed in detail. In addition to examining the sensitivity of the sequence of layer thicknesses to model type and threshold, parallels with terrestrial ocean margin deposition are drawn with a view to better understanding the effects of a prolonged interval of nondeposition on stratigraphy and the modification of the central polar stratigraphy by scarp margin effects. When the threshold for deposition lies in the midrange with respect to excursions of the climate function, deposition occurs about half of the time, and there is only a slight modulation of the layer thickness. When the threshold for deposition is high, deposition occurs only a small fraction of the total time, and groups of layers form which are separated from other groups by long periods of nondeposition.

Cutts, J. A.↗

Calculation of molecular excitation rates

State-to-state collisional excitation rates for interstellar molecules observed by radio astronomers continue to be required to interpret observed line intensities in terms of local temperatures and densities. A problem of particular interest is collisional excitation of water which is important for modeling the observed interstellar masers. In earlier work supported by a different NASA Grant, excitation of water in collisions with He atoms was studied; after many years of successively more refined calculations that problem now seems to be well understood, and discrepancies with earlier experimental data for related (pressure broadening) phenomena are believed to reflect experimental errors. Because of interstellar abundances, excitation by H2, the dominant interstellar species, is much more important than excitation by He, although it has been argued that rates for excitation by these are similar. Under the current grant theoretical study of this problem has begun which is greatly complicated by the additional degrees of freedom which must be included both in determining the interaction potential and also in the molecular scattering calculation. We have now computed the interaction forces for nearly a thousand molecular geometries and are close to having an acceptable global fit to these points which is necessary for the molecular dynamics calculations. Also, extensive modifications have been made to the molecular scattering code, MOLSCAT. These included coding the rotational basis sets and coupling matrix elements required for collisions of an asymmetric top with a linear rotor. A new method for numerical solution of the coupled equations has been incorporated. Because of the long-ranged nature of the water-hydrogen interaction it is necessary to integrate the equations to rather large intermolecular separations, and the integration methods previously available in MOLSCAT are not ideal for such cases. However, the method used by Alexander in his HIBRIDON code is particularly suited for such cases. We have obtained this code and incorporated that part which solves the coupled differential equations as an option in the MOLSCAT program.

Flynn, George↗

Radiative interaction of atmosphere and surface: write up with elements of code

In passive satellite remote sensing of the Earth, separation of the path radiance (atmosphere-only contribution) from the surface reflection remains a “significant challenge”. Recent literature names it among the gaps in radiative transfer (RT) topics that “require continued research in the near future”. The challenge comes from multiple reflections (bouncing) between the atmosphere and surface – radiative interaction. In this paper we use a known RT technique, the matrix-operator method (MOM), and a new modification of the monochromatic vector RT (vRT) code IPOL (Intensity and POLarization) to simulate the interaction of a plane-parallel atmosphere and a few widely used surface reflection models. Following the idea of the Green’s function method, IPOL no longer takes the surface model parameters on input. Instead, it provides the path radiance, and the atmospheric reflection and transmission matrices as output. Despite many RT codes use the MOM formalism, this output does not seem common. The surface reflection matrix is computed externally. Therefore, this paper extends the Green’s function atmospheric correction technique to the case of polarized light. Aiming clarity rather than performance, we explain in Python the structure of the surface matrices for the isotropic (Lambertian), directional unpolarized, and polarized ocean reflection models. We then combine these surface matrices and the precomputed IPOL output to get numerically accurate signal at the top of atmosphere (TOA) and test it vs. published benchmarks. Then, for each benchmark scenario we show how to get the surface from the TOA signal, i.e. perform the RT-based atmospheric correction.

radiative transfer↗

Mark 4-A DSCC telemetry system description

The DSN is undertaking a major modification of the Mark 3. The modified network described is the Mark 4-A. The DSCC portion of the DSN telemetry system is changed in two major ways as a result of the Mark 4-A DSN implementation. Two 34 meter antennas are added to each deep space communications complex (DSCC). The arraying of those antennas with the existing 64 and 34 meter antennas will provide the equivalent of two separate 64 meter antennas or two 64 meter antennas arrayed together. To accomplish this, the DSCC is modified to provide baseband combining of three 34 meter antennas and one 64 meter antenna. The telemetry system is configured to support either two deep space missions and one highly elliptical orbiter or two highly elliptical orbiters and one deep space mission. Highly elliptical orbiter missions have data rates up to 202 ksps modulated directly on the carrier.

Burt, R.↗

Particle-laden weakly swirling free jets: Measurements and predictions

A theoretical and experimental investigation of particle-laden, weakly swirling, turbulent free jets was conducted. Glass particles, having a Sauter mean diameter of 39 microns, with a standard deviation of 15 microns, were used. A single loading ratio (the mass flow rate of particles per unit mass flow rate of air) of 0.2 was used in the experiments. Measurements are reported for three swirl numbers, ranging from 0 to 0.33. The measurements included mean and fluctuating velocities of both phases, and particle mass flux distributions. Measurements were also completed for single-phase non-swirling and swirling jets, as baselines. Measurements were compared with predictions from three types of multiphase flow analysis, as follows: (1) locally homogeneous flow (LHF) where slip between the phases was neglected; (2) deterministic separated flow (DSF), where slip was considered but effects of turbulence/particle interactions were neglected; and (3) stochastic separated flow (SSF), where effects of both interphase slip and turbulence/particle interactions were considered using random sampling for turbulence properties in conjunction with random-walk computations for particle motion. Single-phase weakly swirling jets were considered first. Predictions using a standard k-epsilon turbulence model, as well as two versions modified to account for effects of streamline curvature, were compared with measurements. Predictions using a streamline curvature modification based on the flux Richardson number gave better agreement with measurements for the single-phase swirling jets than the standard k-epsilon model. For the particle-laden jets, the LHF and DSF models did not provide very satisfactory predictions. The LHF model generally overestimated the rate of decay of particle mean axial and angular velocities with streamwise distance, and predicted particle mass fluxes also showed poor agreement with measurements, due to the assumption of no-slip between phases. The DSF model also performed quite poorly for predictions of particle mass flux because turbulent dispersion of the particles was neglected. The SSF model, which accounts for both particle inertia and turbulent dispersion of the particles, yielded reasonably good predictions throughout the flow field for the particle-laden jets.

Bulzan, Daniel L.↗